Make use of SDIO CRC error workaround hardware flag and avoid
target revision checks.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
AR6004(UB134) firmware supports only LP Endpoint, So map
all Access Categories to Low Priority endpoints. This fixes a WPA2
connection issue as the uplink(tx) endpoint is appropriately
mapped in sync with the firmware.
Tested-by: Ben Gray <ben.r.gray@gmail.com>
Reported-by: Ben Gray <ben.r.gray@gmail.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently AR6004 handles the inactivity timeout resolution
in minutes rather than seconds. So parse the inactivity timeout
to the firmware in minutes. For now we will cleanup the
inactive station entries to the nearest converted minutes
(ex: an inactive time of 70 seconds would take atleast 2 - 3 minutes)
Tested with surprise removal of client cards/host shutdown.
Cc: Manikandan Radhakrishnan <mradhakr@qca.qualcomm.com>
Reported-by: Leela Kella <leela@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rename ATH6KL_HW_FLAG_64BIT_RATES to ATH6KL_HW_64BIT_RATES.
This seemed to be necessary to add/use new hardware flags
without exceeding 80 lines. We shall be adding new hw flags
dropping the FLAG term.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a modparam to configure recovery. Recovery
from firmware error is disabled by default to debug
the actual issue further. To recovery from error,
modprobe ath6kl_core recovery_enable=1.
Reported-by: Jin Navy <nhjin@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a bit in ath6kl_dev_state to maintian the run time state
of firmware recovery configuration. This would help to have
user configuration in fw_recovery which will be added in
a separate patch.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some error conditions, fw pauses HTC pipes which would
result in control endpoint full condition. When we hit this
case, most of the time the device will be unusable. Re-initialize
the target to recover from this situation.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds support to detect fw error condition by sending
periodic message (heart beat challenge) to firmware. Upon reception
of the message, fw would send a response event to driver. When
there are no reponses from fw for about 5 cmd driver would
trigger the recovery logic assuming that fw has gone into an
error state.
Capable fw will advertise this capability through
ATH6KL_FW_CAPABILITY_HEART_BEAT_POLL bit. This feature
is disabled by default, can be enabled through a modparam
(heart_beat_poll). This modparam also confiures the polling
interval in msecs.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Re-initialize the target when fw crash is reported.
This would make the device functional again after
target crash. During the target re-initialization
it is made sure that target is not bugged with data/cmd
request, ar->state ATH6KL_STATE_RECOVERY is used
for this purpose.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch reflects changes in the firmware scheduled scan
implementation to behave better in cases with multiple concurrent vifs.
Major changes:
- scheduled scan filters and state are now programmed per-vif.
- decouple scheduled scan from host sleep.
To maintain graceful failure with old firmwares, a new firmware
capability bit is introduced: ATH6KL_FW_CAPABILITY_SCHED_SCAN_V2.
ath6kl simply won't advertise scheduled scan to cfg80211 if the
SCHED_SCAN_V2 is not supported.
Since firmwares from here on out won't support the previous implicit API
for scheduled scan (set WoW filters and host sleep), bump the firmware
API to protect old drivers.
Unfortunately, due to firmware RAM constraints ath6kl still cannot
expect a scan complete event at the end of a scheduled scan results
cycle, so the sched_scan_timer is retained.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If the firmware decides to initiate a channel switch on an AP vif
running an RSN BSS, reconfigure the saved RSN IE capabilities as well.
Fixes a bug where the beacon and 4-way handshake would have a capability
mismatch after a channel switch, since the firmware apparently clears
these on an AP disconnect.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When an ath6kl STA vif is issued a connect command, the firmware will
disconnect all other beaconing vifs in preparation for a potential
channel switch. The case where the connect fails is currently unhandled,
so if a connection attempt on a STA vif fails and any vifs were waiting
for a new channel, simply restart the concurrent vifs on their previous
channel.
Requires that we start tracking the last issued channel in ar->last_ch,
which is valid since ath6kl only supports 1 channel at a time.
Also clear the beaconing vif's want_ch_switch bit regardless of whether
channel switch succeeds, to stop recommitting the same failed profile.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To make it possible to change the country code from user space via nl80211
add handler for reg_notifier. The feature is only enabled when built
time option CONFIG_ATH6KL_REGDOMAIN is enabled, which again depends on
CFG80211_CERTIFICATION_ONUS for certication purposes.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath6kl firmware can monitor a connection and report when a certain
TX failure threshold is crossed. Support this configuration and event
reporting on compatible firmwares.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for AR6004 hardware with version 1.3 and has
id 0x31c8088a.
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware and driver generate MAC addresses for the second and third interfaces.
In addition to the existing algorithm, flip bit 7 of 5th octet. Since both
firmware and driver individually generate the MAC addresses, introduce a new
firmware capability bit to keep them compatible.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath6kl firmware can filter scan results based on rssi. This is
useful to limit hosts wakeups on scheduled scans.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The management frame and remain-on-channel APIs will be
needed in the P2P device abstraction, so move them over
to the new wdev-based APIs. Userspace can still use both
the interface index and wdev identifier for them so it's
backward compatible, but for the P2P Device wdev it will
be able to use the wdev identifier only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is frequent downlink throughput drop to 0 when operating
at the signal level between -42dBm to -53dBm. This has been root
caused to the delay in releasing pending a-mpdu subframes in
reorder buffer. Right now the timeout value is 400ms, there
is also a race condition where timeout handler can be delayed
to run at an extra timeout interval. This patch reduces the
timout interval to reasonable 100ms and makes sure releasing
pending frames are not skipped in the timeout handler by removing
the flag (rxtid->progress) which can delay the timeout logic.
Reported-by: Yu Yanzhi <yanzhiy@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are many places where tid data are accessed without
the lock (rxtid->lock), this can lead to a race condition
when the timeout handler for aggregatin reorder and the
receive function are getting executed at the same time.
Fix this race, but still there are races which can not
be fixed without rewriting the whole aggregation reorder
logic, for now fix the obvious ones.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of setting the channel first and then
starting the AP, let cfg80211 store the channel
and provide it as one of the AP settings.
This means that now you have to set the channel
before you can start an AP interface, but since
hostapd/wpa_supplicant always do that we're OK
with this change.
Alternatively, it's now possible to give the
channel as an attribute to the start-ap nl80211
command, overriding any preset channel.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In virtual interface structure, for each band separate ht cap
is needed. so that one can disable or enable ht capability band
wise.
This will fix the following issue:
1) Disable 11n from supplicant and start a P2P GO.
2) In beacon frames no HT-CAP IE is seen which is expected.
3) Now remove the P2P GO and kill the supplicant.
4) Beacon stops
5) Now using iw associate to an external AP in 5 GHZ
6) In 5 GHZ no HT IE going in assoc request but
when associated in 2.4 GHZ can see HT IES over the air
in assoc request.
In the code for del_beacon in cfg80211.c,set_ht_cap is being
called first for 2.4 GHZ and then for 5 GHZ. When called
for the first time for 2.4 GHZ the enable flag will be set to true
and so when called for the second time for 5 GHZ it just returns
after checking the flag.
Also using this one can have different HT capabilities
per band (for example one may decide not to use 20/40 in 2.4 GHZ
but use it in 5 GHZ). So maintaining a single context is not ok.
it is true for even the enable/disable flag and other HT
capabilities as well
Signed-off-by: Kiran Reddy <c_lreddy@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tx legacy and mcs rateset can configured using iw for
2.4 and 5 bands. Add support for the same in driver.
kvalo: add an enum for the hw flags and rename the flag accordingly,
rename ath6kl_cfg80211_set_bitrate_mask() to a shorter version to make
it easier to indent
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Scheduled scan implementation was only taking probed list into
consideration. The matched list was dropped. This would cause
FW not to report the AP as the list never had that AP's SSID
populated. This was causing long connection time when supplicant
would just issue a wild card SSID in probed list. As a part of
this implementation, ath6kl driver would create a complete list
by taking both probed and matched list and pass it to FW. FW would
probe for the SSID that it needs to and would match against the
relevant SSIDS that is been configured.
kvalo: whitespace changes, less indentation in the for loop, use ++
Signed-off-by: Naveen Singh <navesing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable enhanced bmiss detection if the firmware supports it. This
feature is only enabled on some firmwares since it comes with a power
cost.
Also add a few missing command ids to keep the enums straight.
kvalo: fix a compiler with ath6kl_err(), add few empty lines
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Infrastructure to enable Multicast WOW support based on
firmware capability added to the driver.This enables
different customers or chips to control this feature based
on firmware capability.
kvalo: Firmware capability infrastructure for multicast wow feature,
indetation fixes.
Signed-off-by: Naveen Gangadharan <ngangadh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch enables all multicast packets in non suspend mode
and enable multicast filtering in wow suspend mode. This also
fixes a bug in multicast where the driver assumed disable
multicast-all command disabled/filtered all multicast
packets, which was wrong assumption, because firmware will
apply the programmed filter.
Multicast requirements
- Enable forward all multicast packets(no filtering) in
non suspend mode.
- Enable multicast filtering in wow suspend mode for both
AP and CLIENT.
kvalo: fix a checkpatch warning and drop unrelated newline removal
Signed-off-by: Naveen Gangadharan <ngangadh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the supported bands are just hard coded in the driver.
However, the ath6kl FW will include its 11n and band capabilites in a
WMI_READY event. Handle this and report capabilites to cfg80211
accordingly.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added a new member bg_scan_period in struct ath6kl_vif
to retain background scan period value configured via debugfs
entry 'bgscan_interval'. This backup is needed in schedule scan
path while configuring scan parameters.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
kvalo: do the same changes for ar6004 hw1.2 as well
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the necessary change for AR6004 1.2 chip support
Signed-off-by: Ray Chen <raychen@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If an ath6kl AP vif is beaconing on one channel, and a STA vif
associates on a different channel, a WMI_DISCONNECT event will be sent
to the AP vif. Make the AP vif follow the STA interface, and notify
userspace.
kvalo: fix a sparse warning with vif->next_chan
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
RSN capability field of RSN IE which is generated (which is what really
advertised in beacon/probe response) differs from the one generated in
wpa_supplicant. This inconsistency in rsn IE results in 4-way handshake
failure. To fix this, configure rsn capability used in wpa_supplicant
in firmware using a new wmi command, WMI_SET_IE_CMDID. There is a bit
(ATH6KL_FW_CAPABILITY_RSN_CAP_OVERRIDE) in fw_capabilities to advertise
this support to driver.
Signed-off-by: Subramania Sharma <sharmat@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch disables HT in start_ap if the type of the channel on
which the AP mode is going to be operating is non-HT. HT is enabled
with default ht cap setting if the operating channel is going to be
11n.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In preparation for adding HTC pipe implementation add htc-ops.h to make
it possible dynamically choose which HTC type is used.
Needed for full USB support.
Based on the code by Ray Chen <raychen@qca.qualcomm.com>.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Ray Chen <raychen@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is needed by the USB code. Also while at it replace one void pointer
with a properly typed pointer.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Configure the inactivity timeout passed in start_ap() to
firmware. This capability is advertised only when fw supports
it, there is a new bit (ATH6KL_FW_CAPABILITY_INACTIVITY_TIMEOUT)
in firmware capability ie for driver to learn fw's capability.
After the fw finds out the station is inactive, it will probe
the station with null func frames. By default, the timeout is
10 secs.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When the device is in P2P GO mode and in listen state, the correct behavior is
to see two different probe response frames - one from P2P device and the other
from GO. wpa_supplicant uses the same mechanism to send the frame in both cases
(ath6kl_mgmt_tx). For GO probe response, ath6kl needs to call
ath6kl_send_go_probe_resp (this will add only WSC/P2P IEs and the rest of the
IEs are filled in by the firmware). That was done based on the nw_type ==
AP_NETWORK which would work if P2P Device role were in a separate netdev. When
P2P Device and GO use the same netdev, ath6kl needs to use the special GO probe
response case only if SSID is longer than P2P wildcard SSID.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Also fixes quite a few checkpatch warnings like this:
ath6kl/hif.h:226: CHECK: spinlock_t definition without comment
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
reported by checkpatch:
ath6kl/core.h:748: ERROR: "foo * bar" should be "foo *bar"
ath6kl/core.h:751: ERROR: "foo * bar" should be "foo *bar"
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* In order to save the target power in WOW suspend state,
configure the best optimal values for the below parameters,
- listen interval.
- beacon miss interval.
- scan parameters.
Default values for above attributes are reverted in
wow resume operation.
* The default listen interval is set before the host issue
connect request.
* New function is added to configure beacon miss count.
kvalo: minor changes to fix open parenthesis alignment
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware has the option to support the listen interval
per vif specific. Fix this.
Listen interval can be set by the TUs or by the number
of beacons. Current code enables the user to configure
the listen interval in the unit of 'number of beacons'
using debugfs entry "listen_interval". Going forward,
we need to alter the listen interval in the unit of TUs
to get good power numbers while going to WOW suspend/resume.
Allowing the user to change the listen interval in
the unit of "number of beacons" in debugfs and changing
listen interval in wow suspend/resume in the unit of
time (TUs) would lead us to confuse.
This patch make sures the listen interval is changed only
in the unit of time (TUs).
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Below two scenarios are taken care in this patch which helped
to fix the firmware crash during wow suspend/resume.
* TX operation (ctrl tx and data tx) has to be controlled based
on suspend state. i.e, with respect to WOW mode, control packets
are allowed to send from the host until the suspend state goes
ATH6KL_STATE_WOW and the data packets are allowed until WOW
suspend operation starts.
* Similarly, wow resume is NOT allowed if WOW suspend is in progress.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It gives flexibility to the user to define suspend policy
when the suspend mode is set to WOW and the device is in
disconnected state at the time of suspend.
New module parameter wow_mode is added to get the choice
from the user. This parameter is valid only if the module
parameter suspend_mode is set to WOW.
To force WOW in connected state and cut power
in disconnected state:
suspend_mode=0x3 wow_mode=0x1
To force WOW in connected state and deep sleep
in disconnected state (this is also the default wow_mode):
suspend_mode=0x3 wow_mode=0x2
If there is no value specified to wow_mode during insmod,
deep sleep mode will be tried in the disconnected state.
kvalo: clarified commit log
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As regulatory events are processed even before the wiphy is registered,
calling regulatory_hint() at early stage should be fixed.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes the device get into scan state as soon as a
scan request is received, instead of blocking the scan
request till the traffic comes down. It is necessary
for the deterministic foreground scan particularly when
having multiple vif operating where, if the scan is non-
deterministic, scan on one interface will not start
as long as there are traffic on the other interface. This
change passes 50 msec as foreground scan interval to fix this.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
PS buffering of unicast Action frames that are sent in a context
of a BSS. In AP mode when the recepient station goes to powersave
and PS_POLL flag is not set, we would buffer the frames. Send out
unicast mgmt bufferred frame when PS_POLL is received.
This fixes a bug in P2P GO behavior when sending a GO Discoverability
Request to a client that is in sleep mode.
kvalo: indentation fixes
Signed-off-by: Thirumalai Pachamuthu <tpachamu@qca.qualcomm.com>
Signed-off-by: Naveen Gangadharan <ngangadh@qca.qualcomm.com>
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Update license header with the copyright to Qualcomm Atheros, Inc.
for the year 2011-2012.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Mohammed Shafi Shajakhan
Vasanthakumar Thiagarajan
Thomas Pedersen
Kalle Valo
Bala Shanmugam
Aarthi Thiruvengadam
Johannes Berg
Kiran Reddy
Naveen Singh
Naveen Gangadharan
Raja Mani
Tim Gardner
Ray Chen