The debug interface is substandard and on error returns either
NULL or an error code packed in the pointer. So using "IS_ERR"
for the pointers returned by debugfs function is incorrect.
Instead, we should use IS_ERR_OR_NULL.
This path is an improved vestion of the original patch from
Phil Carmody.
Reported-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
This is just a small clean-up patch which simlifies and unifies the
error path in the dbg_debugfs_init_fs(). We have common error path
for all failure cases in this function except of the very first
case. And this patch makes the first failure case use the same
error path as the other cases by using the 'fname' and 'dent'
variables.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
All UBIFS needs is to make sure we stacktraces when UBIFS debugging
is enabled. It is enough to select KALLSYMS for this, KALLSYMS_ALL
is not necessary. Moreover, Randy Dunlap reported that UBIFS causes
the following Kconfig dependency warning:
warning: (UBIFS_FS_DEBUG && LOCKDEP && LATENCYTOP) selects KALLSYMS_ALL
which has unmet direct dependencies (DEBUG_KERNEL && KALLSYMS)
The reason is that KALLSYMS_ALL requires DEBUG_KERNEL and KALLSYMS, so
ideally, to select KALLSYMS_ALL we'd need to select DEBUG_KERNEL and
KALLSYMS first.
This seems to be too much to select. The easiest way to go is to forget
about KALLSYMS_ALL and just select KALLSYMS when UBIFS debugging is
enabled - that should be enough for stackdumps.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
This patch fixes UBIFS assertion warnings like:
UBIFS assert failed in ubifs_leb_unmap at 135 (pid 29365)
Pid: 29365, comm: integck Tainted: G I 2.6.37-ubi-2.6+ #34
Call Trace:
[<ffffffffa047c663>] ubifs_lpt_init+0x95e/0x9ee [ubifs]
[<ffffffffa04623a7>] ubifs_remount_fs+0x2c7/0x762 [ubifs]
[<ffffffff810f066e>] do_remount_sb+0xb6/0x101
[<ffffffff81106ff4>] ? do_mount+0x191/0x78e
[<ffffffff811070bb>] do_mount+0x258/0x78e
[<ffffffff810da1e8>] ? alloc_pages_current+0xa2/0xc5
[<ffffffff81107674>] sys_mount+0x83/0xbd
[<ffffffff81009a12>] system_call_fastpath+0x16/0x1b
They happen when we re-mount from R/O mode to R/W mode. While
re-mounting, we write to the media, but we still have the c->ro_mount
flag set. The fix is very simple - just clear the flag before
starting re-mounting R/W.
These warnings are caused by the following commit:
2ef13294d2
For -stable guys: this bug was introduced in 2.6.38, this is materieal
for 2.6.38-stable.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org [2.6.38]
Thanks to coverity which spotted that UBIFS will oops if 'kmalloc()'
in 'read_pnode()' fails and we dereference a NULL 'pnode' pointer
when we 'goto out'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org
This fix makes the 'dbg_check_old_index()' function return
immediately if debugging is disabled, instead of executing
incorrect 'goto out' which causes UBIFS to:
1. Allocate memory
2. Read the flash
On every commit. OK, we do not commit that often, but it is
still silly to do unneeded I/O anyway.
Credits to coverity for spotting this silly issue.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org
* 'for-2.6.39/core' of git://git.kernel.dk/linux-2.6-block: (65 commits)
Documentation/iostats.txt: bit-size reference etc.
cfq-iosched: removing unnecessary think time checking
cfq-iosched: Don't clear queue stats when preempt.
blk-throttle: Reset group slice when limits are changed
blk-cgroup: Only give unaccounted_time under debug
cfq-iosched: Don't set active queue in preempt
block: fix non-atomic access to genhd inflight structures
block: attempt to merge with existing requests on plug flush
block: NULL dereference on error path in __blkdev_get()
cfq-iosched: Don't update group weights when on service tree
fs: assign sb->s_bdi to default_backing_dev_info if the bdi is going away
block: Require subsystems to explicitly allocate bio_set integrity mempool
jbd2: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
jbd: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
fs: make fsync_buffers_list() plug
mm: make generic_writepages() use plugging
blk-cgroup: Add unaccounted time to timeslice_used.
block: fixup plugging stubs for !CONFIG_BLOCK
block: remove obsolete comments for blkdev_issue_zeroout.
blktrace: Use rq->cmd_flags directly in blk_add_trace_rq.
...
Fix up conflicts in fs/{aio.c,super.c}
This patch fixes the following UBIFS assertion warning:
UBIFS assert failed in do_readpage at 115 (pid 199)
[<b00321b8>] (unwind_backtrace+0x0/0xdc) from [<af025118>]
(do_readpage+0x108/0x594 [ubifs])
[<af025118>] (do_readpage+0x108/0x594 [ubifs]) from [<af025764>]
(ubifs_write_end+0x1c0/0x2e8 [ubifs])
[<af025764>] (ubifs_write_end+0x1c0/0x2e8 [ubifs]) from
[<b00a0164>] (generic_file_buffered_write+0x18c/0x270)
[<b00a0164>] (generic_file_buffered_write+0x18c/0x270) from
[<b00a08d4>] (__generic_file_aio_write+0x478/0x4c0)
[<b00a08d4>] (__generic_file_aio_write+0x478/0x4c0) from
[<b00a0984>] (generic_file_aio_write+0x68/0xc8)
[<b00a0984>] (generic_file_aio_write+0x68/0xc8) from
[<af024a78>] (ubifs_aio_write+0x178/0x1d8 [ubifs])
[<af024a78>] (ubifs_aio_write+0x178/0x1d8 [ubifs]) from
[<b00d104c>] (do_sync_write+0xb0/0x100)
[<b00d104c>] (do_sync_write+0xb0/0x100) from [<b00d1abc>]
(vfs_write+0xac/0x154)
[<b00d1abc>] (vfs_write+0xac/0x154) from [<b00d1c10>]
(sys_write+0x3c/0x68)
[<b00d1c10>] (sys_write+0x3c/0x68) from [<b002d9a0>]
(ret_fast_syscall+0x0/0x2c)
The 'PG_checked' flag is used to indicate that the page does not
supposedly exist on the media (e.g., a hole or a page beyond the
inode size), so it requires slightly bigger budget, because we have
to account the indexing size increase. And this flag basically
tells that the budget for this page has to be "new page budget".
The "new page budget" is slightly bigger than the "existing page
budget".
The 'do_readpage()' function has the following assertion which
sometimes is hit: 'ubifs_assert(!PageChecked(page))'. Obviously,
the meaning of this assertion is: "I should not be asked to read
a page which does not exist on the media".
However, in 'ubifs_write_begin()' we have a small "trick". Notice,
that VFS may write pages which were not read yet, so the page data
were not loaded from the media to the page cache yet. If VFS tells
that it is going to change only some part of the page, we obviously
have to load it from the media. However, if VFS tells that it is
going to change whole page, we do not read it from the media for
optimization purposes.
However, since we do not read it, we do not know if it exists on
the media or not (a hole, etc). So we set the 'PG_checked' flag
to this page to force bigger budget, just in case.
So 'ubifs_write_begin()' sets 'PG_checked'. Then we are in
'ubifs_write_end()'. And VFS tells us: "hey, for some reasons I
changed my mind and did not change whole page". Frankly, I do not
know why this happens, but I hit this somehow on an ARM platform.
And this is extremely rare.
So in this case UBIFS does the following:
1. Cancels allocated budget.
2. Loads the page from the media by calling 'do_readpage()'.
3. Asks VFS to repeat the whole write operation from the very
beginning (call '->write_begin() again, etc).
And the assertion warning is hit at the step 2 - remember we have
the 'PG_checked' set for this page, and 'do_readpage()' does not
like this. So this patch fixes the problem by adding step 1.5 and
cleaning the 'PG_checked' before calling 'do_readpage()'.
All in all, this patch does not fix any functionality issue, but it
silences UBIFS false positive warning which may happen in very very
rare cases.
And while on it, this patch also improves a commentary which explains
the reasons of setting the 'PG_checked' flag for the page. The old
commentary was a bit difficult to understand.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Simplify UBIFS configuration menu and kill the option to enable self-check
compile-time. We do not really need this because we can do this run-time
using the module parameters or the corresponding sysfs interfaces. And
there is a value in simplifying the kernel configuration menu which becomes
increasingly large.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch fixes a brown-paperbag bug which was introduced by me:
I used incorrect "GFP_KERNEL | GFP_NOFS" allocation flags to make
sure my allocations do not cause write-back. But the correct form
is "GFP_NOFS".
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
And give it a kernel-doc comment.
[akpm@linux-foundation.org: btrfs changed in linux-next]
Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Daniel Lezcano <daniel.lezcano@free.fr>
Acked-by: David Howells <dhowells@redhat.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'linux-next' of git://git.infradead.org/ubifs-2.6: (25 commits)
UBIFS: clean-up commentaries
UBIFS: save 128KiB or more RAM
UBIFS: allocate orphans scan buffer on demand
UBIFS: allocate lpt dump buffer on demand
UBIFS: allocate ltab checking buffer on demand
UBIFS: allocate scanning buffer on demand
UBIFS: allocate dump buffer on demand
UBIFS: do not check data crc by default
UBIFS: simplify UBIFS Kconfig menu
UBIFS: print max. index node size
UBIFS: handle allocation failures in UBIFS write path
UBIFS: use max_write_size during recovery
UBIFS: use max_write_size for write-buffers
UBIFS: introduce write-buffer size field
UBI: incorporate LEB offset information
UBIFS: incorporate maximum write size
UBI: provide LEB offset information
UBI: incorporate maximum write size
UBIFS: fix LEB number in printk
UBIFS: restrict world-writable debugfs files
...
When debugging is enabled, we allocate a buffer of PEB size for
various debugging purposes. However, now all users of this buffer
are gone and we can safely remove it and save 128KiB or more RAM.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Instead of using pre-allocated 'c->dbg->buf' buffer in
'dbg_scan_orphans()', dynamically allocate it when needed. The intend
is to get rid of the pre-allocated 'c->dbg->buf' buffer and save
128KiB of RAM (or more if PEB size is larger). Indeed, currently we
allocate this memory even if the user never enables any self-check,
which is wasteful.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Instead of using pre-allocated 'c->dbg->buf' buffer in
'dump_lpt_leb()', dynamically allocate it when needed. The intend
is to get rid of the pre-allocated 'c->dbg->buf' buffer and save
128KiB of RAM (or more if PEB size is larger). Indeed, currently we
allocate this memory even if the user never enables any self-check,
which is wasteful.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Instead of using pre-allocated 'c->dbg->buf' buffer in
'dbg_check_ltab_lnum()', dynamically allocate it when needed. The
intend is to get rid of the pre-allocated 'c->dbg->buf' buffer and
save 128KiB of RAM (or more if PEB size is larger). Indeed,
currently we allocate this memory even if the user never enables
any self-check, which is wasteful.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Instead of using pre-allocated 'c->dbg->buf' buffer in
'scan_check_cb()', dynamically allocate it when needed. The intend
is to get rid of the pre-allocated 'c->dbg->buf' buffer and save
128KiB of RAM (or more if PEB size is larger). Indeed, currently we
allocate this memory even if the user never enables any self-check,
which is wasteful.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Instead of using pre-allocated 'c->dbg->buf' buffer in
'dbg_dump_leb()', dynamically allocate it when needed. The intend
is to get rid of the pre-allocated 'c->dbg->buf' buffer and save
128KiB of RAM (or more if PEB size is larger). Indeed, currently we
allocate this memory even if the user never enables any self-check,
which is wasteful.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Now that VFS check for inode->i_nlink == 0 and returns proper
error, remove similar check from file system
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Change the default UBIFS behavior WRT data CRC checking. Currently,
UBIFS checks data CRC when reading, which slows it down quite a bit,
and this is the default option. However, it looks like in average
user does not need this feature and would prefer faster read speed
over extra reliability. And this seems to be de-facto standard that
file-systems do not check data CRC every time they read from the
media.
Thus, make UBIFS default behavior so that it does not check data
CRC. This corresponds to the no_chk_data_crc mount option. Those users
who need extra protection can always enable it using the chk_data_crc
option.
Please, read more information about this feature here:
http://www.linux-mtd.infradead.org/doc/ubifs.html#L_checksumming
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Remove debug message level and debug checks Kconfig options as they
proved to be useless anyway. We have sysfs interface which we can
use for fine-grained debugging messages and checks selection, see
Documentation/filesystems/ubifs.txt for mode details.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Running kernel 2.6.37, my PPC-based device occasionally gets an
order-2 allocation failure in UBIFS, which causes the root FS to
become unwritable:
kswapd0: page allocation failure. order:2, mode:0x4050
Call Trace:
[c787dc30] [c00085b8] show_stack+0x7c/0x194 (unreliable)
[c787dc70] [c0061aec] __alloc_pages_nodemask+0x4f0/0x57c
[c787dd00] [c0061b98] __get_free_pages+0x20/0x50
[c787dd10] [c00e4f88] ubifs_jnl_write_data+0x54/0x200
[c787dd50] [c00e82d4] do_writepage+0x94/0x198
[c787dd90] [c00675e4] shrink_page_list+0x40c/0x77c
[c787de40] [c0067de0] shrink_inactive_list+0x1e0/0x370
[c787de90] [c0068224] shrink_zone+0x2b4/0x2b8
[c787df00] [c0068854] kswapd+0x408/0x5d4
[c787dfb0] [c0037bcc] kthread+0x80/0x84
[c787dff0] [c000ef44] kernel_thread+0x4c/0x68
Similar problems were encountered last April by Tomasz Stanislawski:
http://patchwork.ozlabs.org/patch/50965/
This patch implements Artem's suggested fix: fall back to a
mutex-protected static buffer, allocated at mount time. I tested it
by forcing execution down the failure path, and didn't see any ill
effects.
Artem: massaged the patch a little, improved it so that we'd not
allocate the write reserve buffer when we are in R/O mode.
Signed-off-by: Matthew L. Creech <mlcreech@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
When recovering from unclean reboots UBIFS scans the journal and checks nodes.
If a corrupted node is found, UBIFS tries to check if this is the last node
in the LEB or not. This is is done by checking if there only 0xFF bytes
starting from the next min. I/O unit. However, since now we write in
c->max_write_size, we should actually check for 0xFFs starting from the
next max. write unit.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Switch write-buffers from 'c->min_io_size' to 'c->max_write_size' which
presumably has to be more write speed-efficient. However, when write-buffer
is synchronized, write only the the min. I/O units which contain the
data, do not write whole write-buffer. This is more space-efficient.
Additionally, this patch takes into account that the LEB might not start
from the max. write unit-aligned address.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Currently we assume write-buffer size is always min_io_size. But
this is about to change and write-buffers may be of variable size.
Namely, they will be of max_write_size at the beginning, but will
get smaller when we are approaching the end of LEB.
This is a preparation patch which introduces 'size' field in
the write-buffer structure which carries the current write-buffer
size.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Incorporate the LEB offset information into UBIFS. We'll use this
information in one of the next patches to figure out what are the
max. write size offsets relative to the PEB. So this patch is just
a preparation.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Incorporate maximum write size into the UBIFS description data
structure. This patch just introduces new 'c->max_write_size'
and 'c->max_write_shift' fields as a preparation for the following
patches.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This is a minor patch which fixes the LEB number we print when
corrupted empty space is found.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds more commentaries about UBIFS recovery logic which should
explain the famous UBIFS "corrupt empty space" errors.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch fixes suboptimal UBIFS 'sync_fs()' implementation which causes
flash I/O even if the file-system is synchronized. E.g., a 'printk()'
in the MTD erasure function (e.g., 'nand_erase_nand()') can show that
for every 'sync' shell command UBIFS erases at least one eraseblock.
So '$ while true; do sync; done' will cause huge amount of flash I/O.
The reason for this is that UBIFS commits in 'sync_fs()', and starts the
commit even if there is nothing to commit, e.g., it anyway changes the
log. This patch adds a check in the 'do_commit()' UBIFS functions which
prevents the commit if there is nothing to commit.
Reported-by: Hans J. Koch <hjk@linutronix.de>
Tested-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This is a preparational patch which removes the 'c->always_chk_crc' which was
set during mounting and remounting to R/W mode and introduces 'c->mounting'
flag which is set when mounting. Now the 'c->always_chk_crc' flag is the
same as 'c->remounting_rw && c->mounting'.
This patch is a preparation for the next one which will need to know when we
are mounting and remounting to R/W mode, which is exactly what
'c->always_chk_crc' effectively is, but its name does not suite the
next patch. The other possibility would be to just re-name it, but then
we'd end up with less logical flags coverage.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This is a cosmetic patch which re-arranges variables in 'struct ubifs_info'
so that all boolean-like variables which are only changed during mounting or
re-mounting to R/W mode are places together. Then they are turned into
bit-fields, which makes the structure a little bit smaller.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
RCU free the struct inode. This will allow:
- Subsequent store-free path walking patch. The inode must be consulted for
permissions when walking, so an RCU inode reference is a must.
- sb_inode_list_lock to be moved inside i_lock because sb list walkers who want
to take i_lock no longer need to take sb_inode_list_lock to walk the list in
the first place. This will simplify and optimize locking.
- Could remove some nested trylock loops in dcache code
- Could potentially simplify things a bit in VM land. Do not need to take the
page lock to follow page->mapping.
The downsides of this is the performance cost of using RCU. In a simple
creat/unlink microbenchmark, performance drops by about 10% due to inability to
reuse cache-hot slab objects. As iterations increase and RCU freeing starts
kicking over, this increases to about 20%.
In cases where inode lifetimes are longer (ie. many inodes may be allocated
during the average life span of a single inode), a lot of this cache reuse is
not applicable, so the regression caused by this patch is smaller.
The cache-hot regression could largely be avoided by using SLAB_DESTROY_BY_RCU,
however this adds some complexity to list walking and store-free path walking,
so I prefer to implement this at a later date, if it is shown to be a win in
real situations. I haven't found a regression in any non-micro benchmark so I
doubt it will be a problem.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
* 'linux-next' of git://git.infradead.org/ubifs-2.6:
UBIFS: do not allocate unneeded scan buffer
UBIFS: do not forget to cancel timers
UBIFS: remove a bit of unneeded code
UBIFS: add a commentary about log recovery
UBIFS: avoid kernel error if ubifs superblock read fails
UBIFS: introduce new flags for RO mounts
UBIFS: introduce new flag for RO due to errors
UBIFS: check return code of pnode_lookup
UBIFS: check return code of ubifs_lpt_lookup
UBIFS: improve error reporting when reading bad node
UBIFS: introduce list sorting debugging checks
UBIFS: fix assertion warnings in comparison function
UBIFS: mark unused key objects as invalid
UBIFS: do not write rubbish into truncation scanning node
UBIFS: improve assertion in node comparison functions
UBIFS: do not use key type in list_sort
UBIFS: do not look up truncation nodes
UBIFS: fix assertion warning
UBIFS: do not treat ENOSPC specially
UBIFS: switch to RO mode after synchronizing
In 'ubifs_replay_journal()' we allocate 'sbuf' for scanning the log.
However, we already have 'c->sbuf' for these purposes, so do not
allocate yet another one. This reduces UBIFS memory consumption while
recovering.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This is a bug-fix: when we unmount, and we are currently in R/O
mode because of an error - we do not sync write-buffers, which
means we also do not cancel write-buffer timers we may possibly
have armed. This patch fixes the issue.
The issue can easily be reproduced by enabling UBIFS failure debug
mode (echo 4 > /sys/module/ubifs/parameters/debug_tsts) and
unmounting as soon as a failure happen. At some point the system
oopses because we have an armed hrtimer but UBIFS is unmounted
already.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This is a clean-up patch which:
1. Removes explicite 'hrtimer_cancel()' after 'ubifs_wbuf_sync()' in
'ubifs_remount_ro()', because the timers will be canceled by
'ubifs_wbuf_sync()', no need to cancel them for the second time.
2. Remove "if (c->jheads)" check from 'ubifs_put_super()', because
at journal heads must always be allocated there, since we checked
earlier that we were mounted R/W, and the olny situation when
journal heads are not allocated is when mounter or re-mounted R/O.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Add a commentary which elaborates that 'ubifs_recover_log_leb()' recovers only
the last log LEB, not any. Also remove some unneeded newlines.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
.get_sb is called on mounts with automatic fs detection too, so this
function should print an error if it cannot read the superblock in
debug mode only (new behaviour conforms the other fs types)
Signed-off-by: Steffen Sledz <sledz@dresearch.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Commit 2fde99cb55 "UBIFS: mark VFS SB RO too"
introduced regression. This commit made UBIFS set the 'MS_RDONLY' flag in the
VFS superblock when it switches to R/O mode due to an error. This was done
to make VFS show the R/O UBIFS flag in /proc/mounts.
However, several places in UBIFS relied on the 'MS_RDONLY' flag and assume this
flag can only change when we re-mount. For example, 'ubifs_put_super()'.
This patch introduces new UBIFS flag - 'c->ro_mount' which changes only when
we re-mount, and preserves the way UBIFS was originally mounted (R/W or R/O).
This allows us to de-initialize UBIFS cleanly in 'ubifs_put_super()'.
This patch also changes all 'ubifs_assert(!c->ro_media)' assertions to
'ubifs_assert(!c->ro_media && !c->ro_mount)', because we never should write
anything if the FS was mounter R/O.
All the places where we test for 'MS_RDONLY' flag in the VFS SB were changed
and now we test the 'c->ro_mount' flag instead, because it preserves the
original UBIFS mount type, unlike the 'MS_RDONLY' flag.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The R/O state may have various reasons:
1. The UBI volume is R/O
2. The FS is mounted R/O
3. The FS switched to R/O mode because of an error
However, in UBIFS we have only one variable which represents cases
1 and 3 - 'c->ro_media'. Indeed, we set this to 1 if we switch to
R/O mode due to an error, and then we test it in many places to
make sure that we stop writing as soon as the error happens.
But this is very unclean. One consequence of this, for example, is
that in 'ubifs_remount_fs()' we use 'c->ro_media' to check whether
we are in R/O mode because on an error, and we print a message
in this case. However, if we are in R/O mode because the media
is R/O, our message is bogus.
This patch introduces new flag - 'c->ro_error' which is set when
we switch to R/O mode because of an error. It also changes all
"if (c->ro_media)" checks to "if (c->ro_error)" checks, because
this is what the checks actually mean. We do not need to check
for 'c->ro_media' because if the UBI volume is in R/O mode, we
do not allow R/W mounting, and now writes can happen. This is
guaranteed by VFS. But it is good to double-check this, so this
patch also adds many "ubifs_assert(!c->ro_media)" checks.
In the 'ubifs_remount_fs()' function this patch makes a bit more
changes - it fixes the error messages as well.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Function pnode_lookup may return ERR_PTR(...). Check for it.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Function ubifs_lpt_lookup may return ERR_PTR(...). Check for it.
[Tweaked by Artem Bityutskiy]
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When an error happens during validation of read node, the typical situation is that
the LEB we read is unmapped (due to some bug). It is handy to include the mapping
status into the error message.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The UBIFS bug in the GC list sorting comparison functions inspired
me to write internal debugging check functions which verify that
the list of nodes is sorted properly.
So, this patch implements 2 new debugging functions:
o 'dbg_check_data_nodes_order()' - check order of data nodes list
o 'dbg_check_nondata_nodes_order()' - check order of non-data nodes list
The debugging functions are executed only if general UBIFS debugging checks are
enabled. And they are compiled out if UBIFS debugging is disabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When running the integrity test ('integck' from mtd-utils) on current
UBIFS on 2.6.35, I see that assertions in UBIFS 'list_sort()' comparison
functions trigger sometimes, e.g.:
UBIFS assert failed in data_nodes_cmp at 132 (pid 28311)
My investigation showed that this happens when 'list_sort()' calls the 'cmp()'
function with equivalent arguments. In this case, the 'struct list_head'
parameter, passed to 'cmp()' is bogus, and it does not belong to any element in
the original list.
And this issue seems to be introduced by commit:
commit 835cc0c847
Author: Don Mullis <don.mullis@gmail.com>
Date: Fri Mar 5 13:43:15 2010 -0800
It is easy to work around the issue by doing:
if (a == b)
return 0;
in UBIFS. It works, but 'lib_sort()' should nevertheless be fixed. Although it
is harmless to have this piece of code in UBIFS.
This patch adds that code to both UBIFS 'cmp()' functions:
'data_nodes_cmp()' and 'nondata_nodes_cmp()'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When scanning the flash, UBIFS builds a list of flash nodes of type
'struct ubifs_scan_node'. Each scanned node has a 'snod->key' field. This field
is valid for most of the nodes, but invalid for some node type, e.g., truncation
nodes. It is safer to explicitly initialize such keys to something invalid,
rather than leaving them initialized to all zeros, which has key type of
UBIFS_INO_KEY.
This patch introduces new "fake" key type UBIFS_INVALID_KEY and initializes
unused 'snod->key' objects to this type. It also adds debugging assertions in
the TNC code to make sure no one ever tries to look these nodes up in the TNC.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
In the scanning code, in 'ubifs_add_snod()', we write rubbish into
'snod->key', because we assume that on-flash truncation nodes have a key, but
they do not. If the other parts of UBIFS then mistakenly try to look-up
the truncation node key (they should not do this, but may do because of a bug),
we can succeed and corrupt TNC. It looks like we did have such a situation in
'sort_nodes()' in gc.c.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Improve assertions in gc.c in the comparison functions for 'list_sort()': check
key types _and_ node types.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
In comparison function for 'list_sort()' we use key type to distinguish between
node types. However, we have a bit simper way to detect node type -
'snod->type'. This more logical to use, comparing to decoding key types. Also
allows to get rid of 2 local variables.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When moving nodes in GC, do not try to look up truncation nodes in TNC,
because they do not exist there. This would be harmless, because the TNC
look-up would fail, if we did not have bug 'ubifs_add_snod()' which reads
garbage into 'snod->key'. But in any case, it is less error prone to
explicitly ignore everything but inode, data, dentry and xentry nodes.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch fixes the following false assertion warning:
UBIFS assert failed in data_nodes_cmp at 130 (pid 15107)
The assertion was wrong because it did not take into account that the
node can be an xentry.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
'ubifs_garbage_collect_leb()' should never return '-ENOSPC', and if it
does, this is an error. Thus, do not treat this error code specially.
'-EAGAIN' is a special error code, but not '-ENOSPC'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
In 'ubifs_garbage_collect()' on error path, we first switch to R/O mode, and
then synchronize write-buffers (to make sure no data are lost). But the GC
write-buffer synchronization will fail, because we are already in R/O mode.
This patch re-orders this and makes sure we first synchronize the write-buffer,
and then switch to R/O mode.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (96 commits)
no need for list_for_each_entry_safe()/resetting with superblock list
Fix sget() race with failing mount
vfs: don't hold s_umount over close_bdev_exclusive() call
sysv: do not mark superblock dirty on remount
sysv: do not mark superblock dirty on mount
btrfs: remove junk sb_dirt change
BFS: clean up the superblock usage
AFFS: wait for sb synchronization when needed
AFFS: clean up dirty flag usage
cifs: truncate fallout
mbcache: fix shrinker function return value
mbcache: Remove unused features
add f_flags to struct statfs(64)
pass a struct path to vfs_statfs
update VFS documentation for method changes.
All filesystems that need invalidate_inode_buffers() are doing that explicitly
convert remaining ->clear_inode() to ->evict_inode()
Make ->drop_inode() just return whether inode needs to be dropped
fs/inode.c:clear_inode() is gone
fs/inode.c:evict() doesn't care about delete vs. non-delete paths now
...
Fix up trivial conflicts in fs/nilfs2/super.c
Make sure we check the truncate constraints early on in ->setattr by adding
those checks to inode_change_ok. Also clean up and document inode_change_ok
to make this obvious.
As a fallout we don't have to call inode_newsize_ok from simple_setsize and
simplify it down to a truncate_setsize which doesn't return an error. This
simplifies a lot of setattr implementations and means we use truncate_setsize
almost everywhere. Get rid of fat_setsize now that it's trivial and mark
ext2_setsize static to make the calling convention obvious.
Keep the inode_newsize_ok in vmtruncate for now as all callers need an
audit for its removal anyway.
Note: setattr code in ecryptfs doesn't call inode_change_ok at all and
needs a deeper audit, but that is left for later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In 'mount_ubifs()', in case of 'ubifs_leb_unmap()' falure,
free allocated resources.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The current shrinker implementation requires the registered callback
to have global state to work from. This makes it difficult to shrink
caches that are not global (e.g. per-filesystem caches). Pass the shrinker
structure to the callback so that users can embed the shrinker structure
in the context the shrinker needs to operate on and get back to it in the
callback via container_of().
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
UBIFS tries to alway have an LEB reserved for GC, and stores it
in c->gc_lnum. Besides, there is GC head which points to the current
GC head LEB.
In case of an unclean power cut, what may happen is that the GC head
was switched to the reserved GC LEB (c->gc_lnum), but a new reserved
GC LEB was not created yet. So, after an unclean reboot we may have
no reserved GC LEB, and we need to find a new LEB for this.
To do this, we find a dirty LEB which can fit the current GC head,
move the data, unmap this dirty LEB, and it becomes our reserved GC
LEB.
However, if we cannot find a dirty enough LEB, we return failure,
which is wrong, because we still can have free LEBs to use for
the reserved GC LEB. This patch fixes the issue.
This patch also fixes few typos in comments, which were spotted by
aspell.
Note, this patch fixes a real issue
[ 14.328117] UBIFS: recovery needed
[ 53.941378] UBIFS error (pid 462): ubifs_rcvry_gc_commit: could not find a dirty LEB
[ 89.606399] UBIFS: recovery completed
[ 89.609329] UBIFS assert failed in mount_ubifs at 1358 (pid 462)
[ 89.616165] [<c0026144>] (unwind_backtrace+0x0/0xe4) from [<c0125ce4>] (ubifs_fill_super+0x11d0/0x1c4c)
[ 89.625930] [<c0125ce4>] (ubifs_fill_super+0x11d0/0x1c4c) from [<c0126910>] (ubifs_get_sb+0x1b0/0x354)
[ 89.635696] [<c0126910>] (ubifs_get_sb+0x1b0/0x354) from [<c008a50c>] (vfs_kern_mount+0x50/0xe0)
[ 89.644485] [<c008a50c>] (vfs_kern_mount+0x50/0xe0) from [<c008a5e0>] (do_kern_mount+0x34/0xdc)
[ 89.653274] [<c008a5e0>] (do_kern_mount+0x34/0xdc) from [<c00a29d8>] (do_mount+0x148/0x7cc)
[ 89.662063] [<c00a29d8>] (do_mount+0x148/0x7cc) from [<c00a30f4>] (sys_mount+0x98/0xc8)
[ 89.670852] [<c00a30f4>] (sys_mount+0x98/0xc8) from [<c0021f40>] (ret_fast_syscall+0x0/0x28)
which was reported here:
http://article.gmane.org/gmane.linux.drivers.mtd/29923
by Alexander Pazdnikov <pazdnikov@list.ru>
Reported-by: Alexander Pazdnikov <pazdnikov@list.ru>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reviewed-by: Adrian Hunter <adrian.hunter@nokia.com>
Use ERR_CAST(x) rather than ERR_PTR(PTR_ERR(x)). The former makes more
clear what is the purpose of the operation, which otherwise looks like a
no-op.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The error code from 'ubifs_rcvry_gc_commit()' was ignored, so UBIFS
failed to recover and continued. Instead, we should refuse mounting
the file-system.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Make sure that not only sync_filesystem but all callers of writeback_inodes_sb
have the superblock protected against remount. As-is this disables all
functionality for these callers, but the next patch relies on this locking to
fix writeback_inodes_sb for sync_filesystem.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Lots of filesystems calls vmtruncate despite not implementing the old
->truncate method. Switch them to use simple_setsize and add some
comments about the truncate code where it seems fitting.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If some read/write error happens (eg.CRC error), UBIFS swotches to
read-only mode, but the VFS infomation still not update.
This patch add this also make /proc/mounts update.
Signed-off-by: Zhang Jiejing <kzjeef@gmail.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This reverts commit a069c266ae.
It turns ou that not only was it missing a case (XFS) that needed it,
but perhaps more importantly, people sometimes want to enable new
modules that they hadn't had enabled before, and if such a module uses
list_sort(), it can't easily be inserted any more.
So rather than add a "select LIST_SORT" to the XFS case, just leave it
compiled in. It's not all _that_ big, after all, and the inconvenience
isn't worth it.
Requested-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Don Mullis <don.mullis@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Chinner <david@fromorbit.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Build list_sort() only for configs that need it -- those that don't save
~581 bytes (i386).
Signed-off-by: Don Mullis <don.mullis@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This gives the filesystem more information about the writeback that
is happening. Trond requested this for the NFS unstable write handling,
and other filesystems might benefit from this too by beeing able to
distinguish between the different callers in more detail.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
There are two copies of list_sort() in the tree already, one in the DRM
code, another in ubifs. Now XFS needs this as well. Create a generic
list_sort() function from the ubifs version and convert existing users
to it so we don't end up with yet another copy in the tree.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After I_SYNC was split from I_LOCK the leftover is always used together with
I_NEW and thus superflous.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Return the PTR_ERR of the correct pointer. This fixes the debugging code.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
generic_file_aio_write already calls into ->fsync to handle O_SYNC/O_DSYNC.
Remove the duplicate call to ubifs_sync_wbufs_by_inode which is already
covered by ubifs_fsync.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch makes it possible to mount UBI character device
nodes, and use something like:
$ mount -t ubifs /dev/ubi_volume_name /mnt/ubifs
instead of the old restrictive 'nodev' semantics:
$ mount -t ubifs ubi0_0 /mnt/ubifs
[Comments and the patch were amended a bit by Artem]
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code
But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In 'dbg_check_space_info()' we want to dump current lprops statistics,
but actually dump old statistics. Fix this.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
bdi_start_writeback() is currently split into two paths, one for
WB_SYNC_NONE and one for WB_SYNC_ALL. Add bdi_sync_writeback()
for WB_SYNC_ALL writeback and let bdi_start_writeback() handle
only WB_SYNC_NONE.
Push down the writeback_control allocation and only accept the
parameters that make sense for each function. This cleans up
the API considerably.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We do this automatically in get_sb_bdev() from the set_bdev_super()
callback. Filesystems that have their own private backing_dev_info
must assign that in ->fill_super().
Note that ->s_bdi assignment is required for proper writeback!
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Improve 'dbg_dump_lprop()' and print dark and dead space there,
decode flags, and journal heads.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The journal head names and numbers are part of the UBIFS format, so
they should be in the ubifs-media.h.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This enables us to track who does what and print info. Its main use
is catching dirty inodes on the default_backing_dev_info, so we can
fix that up.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This adds two new exported functions:
- writeback_inodes_sb(), which only attempts to writeback dirty inodes on
this super_block, for WB_SYNC_NONE writeout.
- sync_inodes_sb(), which writes out all dirty inodes on this super_block
and also waits for the IO to complete.
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch amends and nicifies commentaries in file.c, as well as
fixes some spelling problems.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The 'ubifs_scan()' function returns -EUCLEAN if something is corrupted
and recovery is needed, otherwise it returns other error codes. However,
in few places UBIFS does not check the error codes and runs recovery.
This patch changes this behavior and makes UBIFS start recovery only
on -EUCLEAN errors.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reviewed-by: Adrian Hunter <Adrian.Hunter@nokia.com>
At the moment UBIFS print large and scary error messages and
flash dumps in case of nearly any corruption, even if it is
a recoverable corruption. For example, if the master node is
corrupted, ubifs_scan() prints error dumps, then UBIFS recovers
just fine and goes on.
This patch makes UBIFS print scary error messages only in
real cases, which are not recoverable. It adds 'quiet' argument
to the 'ubifs_scan()' function, so the caller may ask 'ubi_scan()'
not to print error messages if the caller is able to do recovery.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reviewed-by: Adrian Hunter <Adrian.Hunter@nokia.com>
Add one more check to UBIFS - a check that makes sure that there
are no data nodes beyond inode size. And few commantaries fixes
along the line.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reviewed-by: Adrian Hunter <Adrian.Hunter@nokia.com>
This patch adds 'const' qualifier to UBIFS xattr inode and file
operations.
Pointed-out-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Nowadays VFS always synchronizes all dirty inodes and pages before
calling '->sync_fs()', so remove unneeded 'generic_sync_sb_inodes()'
from 'ubifs_sync_fs()'. It used to be needed, but not any longer.
Pointed-out-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The BKL was pushed down from VFS to the file-systems. It used
to serialize mount/unmount/remount and prevented more than one
instance of the same file-system from doing
mount/umount/remount at the same time. But it is OK for UBIFS
and it does not need any additional locking for these cases.
Thus, kick the BKL out of UBIFS.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Remove 'xent_key_init_hash()' and 'data_key_init_flash()' functions,
as they are unot used anywhere.
Signed-off-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the 'ubifs_recover_leb()' function, when we find corrupted
empty space, we dump 8K starting from the offset where the last
node ends. This is OK if the corrupted empty space is somewhere
near that offset. But if the corruption is far at the end of the
LEB, we will dump all 0xFF bytes and complitely ignore the
interesting data. This is observed on a PPC ("kilauea") with
NOR flash.
This patch changes the behavior and teaches UBIFS to print only
interesting data. I.e., now we find where corruption starts and
start dumping from that offset.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reviewed-by: Adrian Hunter <Adrian.Hunter@nokia.com>
recovery.c has 'is_empty()' helper and it is better to use
this helper instead of re-implementing it in several places.
This patch does this and removes some amount of unneeded code.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reviewed-by: Adrian Hunter <Adrian.Hunter@nokia.com>
This patch fixes few minor things I've spotted while going through
code:
1. Better document return codes
2. If 'ubifs_scan_a_node()' returns some thing we do not expect,
treat this as an error.
3. Try to do recovery only when 'ubifs_scan()' returns %-EUCLEAN,
not on any error.
4. If empty space starts at a non-aligned address, print a message.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reviewed-by: Adrian Hunter <Adrian.Hunter@nokia.com>
In case of corruptions, dump 8192 bytes instead of 4096. The
largest node is 4096+ bytes, so it is better to see a node
boundary, which is not always possible when only 4096 bytes
are printed.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reviewed-by: Adrian Hunter <Adrian.Hunter@nokia.com>
UBIFS uses a bdi device per volume, but does not care to hand out unique
names to each of them. This causes an error when trying to mount more
than one volumes. Append the UBI volume and device ID to avoid that.
[Amended a bit by Artem Bityutskiy]
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Adrian Hunter <ext-adrian.hunter@nokia.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When debugging is enabled and an unclean file-system is mounter,
the following assertion is triggered:
UBIFS assert failed in ubifs_tnc_start_commit at 805 (pid 1081)
Call Trace:
[cfaffbd0] [c0006cf8] show_stack+0x44/0x16c (unreliable)
[cfaffc10] [c011b738] ubifs_tnc_start_commit+0xbb8/0xd18
[cfaffc90] [c0112670] do_commit+0x150/0xa44
[cfaffd10] [c0125234] ubifs_rcvry_gc_commit+0xd8/0x544
[cfaffd60] [c0100e9c] ubifs_fill_super+0xe78/0x15f8
[cfaffdf0] [c0102118] ubifs_get_sb+0x20c/0x320
[cfaffe70] [c007f764] vfs_kern_mount+0x58/0xe0
[cfaffe90] [c007f83c] do_kern_mount+0x40/0xf8
[cfaffeb0] [c0095c24] do_mount+0x550/0x758
[cfafff10] [c0095ebc] sys_mount+0x90/0xe0
[cfafff40] [c000ed4c] ret_from_syscall+0x0/0x3c
The reason is that we initialize 'c->min_leb_idx' early, and do
not re-calculate it after journal replay.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds the following minor optimization:
1. If write-buffer does not use the timer, indicate it with the
wbuf->no_timer variable, instead of using the wbuf->softlimit
variable. This is better because wbuf->softlimit is of ktime_t
type, and the ktime_to_ns function contains 64-bit multiplication.
2. Do not call the 'hrtimer_cancel()' function for write-buffers
which do not use timers.
3. Do not cancel the timer in 'ubifs_put_super()' because the
synchronization function does this.
This patch also removes a confusing comment.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
1. Make the I/O debugging message print the journal head number.
2. Add prints to timer functions.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Fix the following warning:
fs/ubifs/io.c: In function 'ubifs_wbuf_init':
fs/ubifs/io.c:860: warning: integer overflow in expression
And limit maximum hrtimer delta to ULONG_MAX because the
argument is 'unsigned long'.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
helpers: get_cached_acl(inode, type), set_cached_acl(inode, type, acl),
forget_cached_acl(inode, type).
ubifs/xattr.c needed includes reordered, the rest is a plain switchover.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'linux-next' of git://git.infradead.org/ubifs-2.6:
UBIFS: start using hrtimers
hrtimer: export ktime_add_safe
UBIFS: do not forget to register BDI device
UBIFS: allow sync option in rootflags
UBIFS: remove dead code
UBIFS: use anonymous device
UBIFS: return proper error code if the compr is not present
UBIFS: return error if link and unlink race
UBIFS: reset no_space flag after inode deletion
Move BKL into ->put_super from the only caller. A couple of
filesystems had trivial enough ->put_super (only kfree and NULLing of
s_fs_info + stuff in there) to not get any locking: coda, cramfs, efs,
hugetlbfs, omfs, qnx4, shmem, all others got the full treatment. Most
of them probably don't need it, but I'd rather sort that out individually.
Preferably after all the other BKL pushdowns in that area.
[AV: original used to move lock_super() down as well; these changes are
removed since we don't do lock_super() at all in generic_shutdown_super()
now]
[AV: fuse, btrfs and xfs are known to need no damn BKL, exempt]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Make sure a superblock really is writeable by checking MS_RDONLY
under s_umount. sync_filesystems needed some re-arragement for
that, but all but one sync_filesystem caller had the correct locking
already so that we could add that check there. cachefiles grew
s_umount locking.
I've also added a WARN_ON to sync_filesystem to assert this for
future callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
UBIFS uses timers for write-buffer write-back. It is not
crucial for us to write-back exactly on time. We are fine
to write-back a little earlier or later. And this means
we may optimize UBIFS timer so that it could be groped
with a close timer event, so that the CPU would not be
waken up just to do the write back. This is optimization
to lessen power consumption, which is important in
embedded devices UBIFS is used for.
hrtimers have a nice feature: they are effectively range
timers, and we may defind the soft and hard limits for
it. Standard timers do not have these feature. They may
only be made deferrable, but this means there is effectively
no hard limit. So, we will better use hrtimers.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When passing UBIFS parameters via kernel command line, the
sync option will be passed to UBIFS as a string, not as an
MS_SYNCHRONOUS flag. Teach UBIFS interpreting this flag.
Reported-by: Aurélien GÉRÔME <ag@debian.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
UBIFS assumes that @c->min_io_size is 8 in case of NOR flash. This
is because UBIFS alignes all nodes to 8-byte boundary, and maintaining
@c->min_io_size introduced unnecessary complications.
This patch removes senseless constructs like:
if (c->min_io_size == 1)
NOR-specific code
Also, few commentaries amendments.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
UBIFS has erroneuosly set 'sb->s_dev' to the UBI volume
character device major/minor. This may lead to clashes
if there is another FS mounted to a block device with
the same major/minor numbers. User-space programs which
use 'stat->st_dev' may get confused because of this.
This problem was found by Al Viro. He also pointed the
way to fix the problem - use 'set_anon_super()' and
'kill_anon_super()' VFS helpers.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
If the compressor is not present, mount_ubifs need
to return an error code. This way ubifs_fill_super
will stop and handle the error.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Consider a scenario when 'vfs_link(dirA/fileA)' and
'vfs_unlink(dirA/fileA, dirB/fileB)' race. 'vfs_link()' does not
lock 'dirA->i_mutex', so this is possible. Both of the functions
lock 'fileA->i_mutex' though. Suppose 'vfs_unlink()' wins, and takes
'fileA->i_mutex' mutex first. Suppose 'fileA->i_nlink' is 1. In this
case 'ubifs_unlink()' will drop the last reference, and put 'inodeA'
to the list of orphans. After this, 'vfs_link()' will link
'dirB/fileB' to 'inodeA'. Thir is a problem because, for example,
the subsequent 'vfs_unlink(dirB/fileB)' will add the same inode
to the list of orphans.
This problem was reported by J. R. Okajima <hooanon05@yahoo.co.jp>
[Artem: add more comments, amended commit message]
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When UBIFS runs out of space it spends a lot of time trying to
find more space before returning ENOSPC. As there is no point
repeating that unless something has changed, UBIFS has an
optimization to record that the file system is 100% full and not
try to find space. That flag was not being reset when a pending
deletion was finally done.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Reviewed-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
Change the page_mkwrite prototype to take a struct vm_fault, and return
VM_FAULT_xxx flags. There should be no functional change.
This makes it possible to return much more detailed error information to
the VM (and also can provide more information eg. virtual_address to the
driver, which might be important in some special cases).
This is required for a subsequent fix. And will also make it easier to
merge page_mkwrite() with fault() in future.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <joel.becker@oracle.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
UBIFS did not recovery in a situation in which it could
have. The relevant function assumed there could not be
more nodes in an eraseblock after a corrupted node, but
in fact the last (NAND) page written might contain anything.
The correct approach is to check for empty space (0xFF bytes)
from then on.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
simple_set_mnt() is defined as returning 'int' but always returns 0.
Callers assume simple_set_mnt() never fails and don't properly cleanup if
it were to _ever_ fail. For instance, get_sb_single() and get_sb_nodev()
should:
up_write(sb->s_unmount);
deactivate_super(sb);
if simple_set_mnt() fails.
Since simple_set_mnt() never fails, would be cleaner if it did not
return anything.
[akpm@linux-foundation.org: fix build]
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now UBIFS is supported by u-boot. If we ever decide to change the
media format, then people will have to upgrade their u-boots to
mount new format images. However, very often it is possible to
preserve R/O forward-compatibility, even though the write
forward-compatibility is not preserved.
This patch introduces a new super-block field which stores the
R/O compatibility version.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: Adrian Hunter <Adrian.Hunter@nokia.com>
fs/ubifs/super.c: In function ‘ubifs_show_options’:
fs/ubifs/super.c:425: warning: format not a string literal and no format arguments
fs/ubifs/super.c: In function ‘mount_ubifs’:
fs/ubifs/super.c:1204: warning: format not a string literal and no format arguments
fs/ubifs/super.c: In function ‘ubifs_remount_rw’:
fs/ubifs/super.c:1557: warning: format not a string literal and no format arguments
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The 'joinup()' function cannot deal with situations when nodes
go in reverse order - it just leaves them in this order. This
patch implement full nodes sorting using n*log(n) algorithm.
It sorts data nodes for bulk-read, and direntry nodes for
readdir().
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch introduces a helpful @c->idx_leb_size variable.
The patch also fixes some spelling issues and makes comments
use "LEB" instead of "eraseblock", which is more correct.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Empty journal head LEBs are accounted as taken empty as well, so
the GC LEB does not have to be the only taken empty LEB when
nounting/remounting.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
UBIFS fast path in write_begin may mark a page up to date
and then discover that there may not be enough space to do
the write, and so fall back to a slow path. The slow path
tries harder, but may still find no space - leaving the page
marked up to date, when it is not. This patch ensures that
the page is marked not up to date in that case.
The bug that this patch fixes becomes evident when the write
is into a hole (sparse file) or is at the end of the file
and a subsequent read is off the end of the file. In both
cases, the file system should return zeros but was instead
returning the page that had not been written because the
file system was out of space.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Make 'ubifs_find_free_space()' return offset where free space starts,
rather than the amount of free space. This is just more appropriat
for its caller.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Trivial cleanup, list_del(); list_add{,_tail}() is equivalent
to list_move{,_tail}(). Semantic patch for coccinelle can be
found at www.cccmz.de/~snakebyte/list_move_tail.spatch
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The debugging function dbg_chk_lpt_sz() was not working
correctly for small min_io_unit size e.g. NOR flash.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This UBIFS feature has never worked properly, and it was a mistake
to add it because we simply have no use-cases. So, lets still accept
the fast_unmount mount option, but ignore it. This does not change
much, because UBIFS commit in sync_fs anyway, and sync_fs is called
while unmounting.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When mounting/re-mounting, UBIFS returns EINVAL even if the ENOSPC
or EROFS codes are are much better, just because we have not found
references to ENOSPC/EROFS in mount (2) man pages. This patch
changes this behaviour and makes UBIFS return real error code,
because:
1. It is just less confusing and more logical
2. mount is not described in SuSv3, so it seems to be not really
well-standartized
3. we do not cover all cases, and any random undocumented in man
pages error code may be returned anyway
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
- preserve the idx_gc list - it will be needed in the same
state, should UBIFS be remounted rw again
- prevent remounting ro if we have switched to read only
mode (due to a fatal error)
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
All writes go through wbufs so they must be sync'd
after syncing inodes and pages.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The function to traverse and dirty the LPT was still not
dirtying all nodes, with the result that the LPT could
run out of space.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When data CRC checking is disabled, UBIFS returns incorrect return
code from the 'try_read_node()' function (0 instead of 1, which means
CRC error), which make the caller re-read the data node again, but using
a different code patch, so the second read is fine. Thus, we read the
same node twice. And the result of this is that UBIFS is slower
with no_chk_data_crc option than it is with chk_data_crc option.
This patches fixes the problem.
Reported-by: Reuben Dowle <Reuben.Dowle@navico.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
I introduce wrong assertions in one of the previous commits, this
patch fixes them.
Also, initialize debugfs after the debugging check. This is a little
nicer because we want the FS data to be accessible to external users
after everything has been initialized.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When mounting read-only the orphan area head is
not initialized. It must be initialized when
remounting read/write, but it was not. This patch
fixes that.
[Artem: sorry, added comment tweaking noise]
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When we mount UBIFS, GC LEB may contain out-of-date information,
and UBIFS should update lprops and set free space for thei LEB.
Currently UBIFS does this only if mounted R/W. But for R/O mount
we have to do the same, because otherwise we will have incorrect
FS free space reported to user-space.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
We observe space corrupted accounting when re-mounting. So add some
debbugging checks to catch problems like this.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When freeing the c->idx_lebs list, we have to release the LEBs as well,
because we might be called from mount to read-only mode code. Otherwise
the LEBs stay taken forever, which may cause problems when we re-mount
back ro RW mode.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch simplifies lock_[23]_inodes functions. We do not have
to care about locking order, because UBIFS does this for @i_mutex
and this is enough. Thanks to Al Viro for suggesting this.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
UBIFS wrongly tells UBI that all data is short term. Use proper
hints instead. Thanks to Xiaochuan-Xu for noticing this.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
VFS calls '->sync_fs()' twice - first time with @wait = 0, second
time with @wait = 1. As a result, we may commit and synchronize
write-buffers twice. Avoid doing this by returning immediatelly if
@wait = 0.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
WB_SYNC_HOLD is going to be zapped so we should not use it. Use
%WB_SYNC_NONE instead. Here is what akpm said:
"I think I'll just switch that to WB_SYNC_NONE. The `wait==0' mode is
just an advisory thing to help the fs shove lots of data into the
queues. If some gets missed then it'll be picked up on the second
->sync_fs call, with wait==1."
Thanks to Randy Dunlap for catching this.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the write_begin/write_end aops, page_symlink was broken because it
could no longer pass a GFP_NOFS type mask into the point where the
allocations happened. They are done in write_begin, which would always
assume that the filesystem can be entered from reclaim. This bug could
cause filesystem deadlocks.
The funny thing with having a gfp_t mask there is that it doesn't really
allow the caller to arbitrarily tinker with the context in which it can be
called. It couldn't ever be GFP_ATOMIC, for example, because it needs to
take the page lock. The only thing any callers care about is __GFP_FS
anyway, so turn that into a single flag.
Add a new flag for write_begin, AOP_FLAG_NOFS. Filesystems can now act on
this flag in their write_begin function. Change __grab_cache_page to
accept a nofs argument as well, to honour that flag (while we're there,
change the name to grab_cache_page_write_begin which is more instructive
and does away with random leading underscores).
This is really a more flexible way to go in the end anyway -- if a
filesystem happens to want any extra allocations aside from the pagecache
ones in ints write_begin function, it may now use GFP_KERNEL (rather than
GFP_NOFS) for common case allocations (eg. ocfs2_alloc_write_ctxt, for a
random example).
[kosaki.motohiro@jp.fujitsu.com: fix ubifs]
[kosaki.motohiro@jp.fujitsu.com: fix fuse]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: <stable@kernel.org> [2.6.28.x]
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Cleaned up the calling convention: just pass in the AOP flags
untouched to the grab_cache_page_write_begin() function. That
just simplifies everybody, and may even allow future expansion of the
logic. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'linux-next' of git://git.infradead.org/ubifs-2.6: (33 commits)
UBIFS: add more useful debugging prints
UBIFS: print debugging messages properly
UBIFS: fix numerous spelling mistakes
UBIFS: allow mounting when short of space
UBIFS: fix writing uncompressed files
UBIFS: fix checkpatch.pl warnings
UBIFS: fix sparse warnings
UBIFS: simplify make_free_space
UBIFS: do not lie about used blocks
UBIFS: restore budg_uncommitted_idx
UBIFS: always commit on unmount
UBIFS: use ubi_sync
UBIFS: always commit in sync_fs
UBIFS: fix file-system synchronization
UBIFS: fix constants initialization
UBIFS: avoid unnecessary calculations
UBIFS: re-calculate min_idx_size after the commit
UBIFS: use nicer 64-bit math
UBIFS: fix available blocks count
UBIFS: various comment improvements and fixes
...
We cannot use ubifs_err() macro with DBGKEY() and DBGKEY1(),
because this is racy and holding dbg_lock is needed. Use
dbg_err() instead, which does have the lock held.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
It is fine if there is not free space - we should still allow mounting
this FS. This patch relaxes the free space requirements and adds info
dumps.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
UBIFS does not disable compression if ui->flags is non-zero, e.g.
if the file has "sync" flag. This is because of the typo which
is fixed by this patch. The patch also adds a couple of useful
debugging prints.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
These are mostly long lines and wrong indentation warning
fixes. But also there are two volatile variables and
checkpatch.pl complains about them:
WARNING: Use of volatile is usually wrong: see Documentation/volatile-considered-harmful.txt
+ volatile int gc_seq;
WARNING: Use of volatile is usually wrong: see Documentation/volatile-considered-harmful.txt
+ volatile int gced_lnum;
Well, we anyway use smp_wmb() for c->gc_seq and c->gced_lnum, so
these 'volatile' modifiers can be just dropped.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
fs/ubifs/compress.c:111:8: warning: incorrect type in argument 5 (different signedness)
fs/ubifs/compress.c:111:8: expected unsigned int *dlen
fs/ubifs/compress.c:111:8: got int *out_len
fs/ubifs/compress.c:175:10: warning: incorrect type in argument 5 (different signedness)
fs/ubifs/compress.c:175:10: expected unsigned int *dlen
fs/ubifs/compress.c:175:10: got int *out_len
Fix this by adding a cast to (unsigned int *). We guarantee that
our lengths are small and no overflow is possible.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The 'make_free_space()' function was too complex and this patch
simplifies it. It also fixes a bug - the freespace test failed
straight away on UBI volumes with 512 bytes LEB size.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Do not force UBIFS return 0 used space when it is empty. It leads
to a situation when creating any file immediately produces tens of
used blocks, which looks very weird. It is better to be honest and
say that some blocks are used even if the FS is empty. And ext2
does the same.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
UBIFS stores uncommitted index size in c->budg_uncommitted_idx,
and this affect budgeting calculations. When mounting and
replaying, this variable is not updated, so we may end up
with "over-budgeting". This patch fixes the issue.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
UBIFS commits on unmount to make the next mount faster. Currently,
it commits only if there is more than LEB size bytes in the
journal. This is not very good, because journal size may be
large (512KiB). And there may be few deletions in the journal
which do not take much journal space, but which do introduce
a lot of TNC changes and make mount slow.
Thus, jurt remove this condition and always commit.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Always run commit in sync_fs, because even if the journal seems
to be almost empty, there may be a deletion which removes a large
file, which affects the index greatly. And because we want
better free space predictions after 'sync_fs()', we have to
commit.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Argh. The ->sync_fs call is called _before_ all inodes are flushed.
This means we first sync write buffers and commit, then all
inodes are synced, and we end up with unflushed write buffers!
Fix this by forcing synching all indoes from 'ubifs_sync_fs()'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The c->min_idx_lebs constant depends on c->old_idx_sz, which
is read from the master node. This means that we have to
initialize c->min_idx_lebs only after we have read the master
node.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When we commit, but before we try to write anything to the flash
media, @c->min_idx_size is inaccurate, because we do not re-calculate
it after the commit. Do not forget to do this.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Take into account that 2 eraseblocks are never available because
they are reserved for the index. This gives more realistic count
of FS blocks.
To avoid future confusions like this, introduce a constant.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch fixes the following section mismatch:
WARNING: fs/ubifs/ubifs.o(.init.text+0xec): Section mismatch in reference from the function init_module() to the function .exit.text:ubifs_compressors_exit()
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Conflicts:
fs/nfsd/nfs4recover.c
Manually fixed above to use new creds API functions, e.g.
nfs4_save_creds().
Signed-off-by: James Morris <jmorris@namei.org>
Do not forget to check whether lpt debugging is enabled before
running the check functions. This commit also makes some spelling
fixes.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
We need to have a possibility to see various UBIFS variables
and ask UBIFS to dump various information. Debugfs is what
we need.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Introduce a new data structure which contains all debugging
stuff inside. This is cleaner than having debugging stuff
directly in 'c'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
I have a habit of compiling kernel with
EXTRA_CFLAGS="-Wextra -Wno-unused -Wno-sign-compare -Wno-missing-field-initializers"
and so fs/ubifs/key.h give lots (~10) of these every time:
CC fs/ubifs/tnc_misc.o
In file included from fs/ubifs/ubifs.h:1725,
from fs/ubifs/tnc_misc.c:30:
fs/ubifs/key.h: In function 'key_r5_hash':
fs/ubifs/key.h:64: warning: comparison of unsigned expression >= 0 is always true
fs/ubifs/key.h: In function 'key_test_hash':
fs/ubifs/key.h:81: warning: comparison of unsigned expression >= 0 is always true
This patch fixes the warnings.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
It is very handy to be able to change default UBIFS compressor
via mount options. Introduce -o compr=<name> mount option support.
Currently only "none", "lzo" and "zlib" compressors are supported.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Save a 4 bytes of RAM per 'struct inode' by stroring inode
compression type in bit-filed, instead of using 'int'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
If data does not compress, it is better to leave it uncompressed
because we'll read it faster then. So do not compress data if we
save less than 64 bytes.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
To avoid memory allocation failure during bulk-read, pre-allocate
a bulk-read buffer, so that if there is only one bulk-reader at
a time, it would just use the pre-allocated buffer and would not
do any memory allocation. However, if there are more than 1 bulk-
reader, then only one reader would use the pre-allocated buffer,
while the other reader would allocate the buffer for itself.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Bulk-read allocates 128KiB or more using kmalloc. The allocation
starts failing often when the memory gets fragmented. UBIFS still
works fine in this case, because it falls-back to standard
(non-optimized) read method, though. This patch teaches bulk-read
to allocate exactly the amount of memory it needs, instead of
allocating 128KiB every time.
This patch is also a preparation to the further fix where we'll
have a pre-allocated bulk-read buffer as well. For example, now
the @bu object is prepared in 'ubifs_bulk_read()', so we could
path either pre-allocated or allocated information to
'ubifs_do_bulk_read()' later. Or teaching 'ubifs_do_bulk_read()'
not to allocate 'bu->buf' if it is already there.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Bulk-read allocates a lot of memory with 'kmalloc()', and when it
is/gets fragmented 'kmalloc()' fails with a scarry warning. But
because bulk-read is just an optimization, UBIFS keeps working fine.
Supress the warning by passing __GFP_NOWARN option to 'kmalloc()'.
This patch also introduces a macro for the magic 128KiB constant.
This is just neater.
Note, this is not really fixes the problem we had, but just hides
the warnings. The further patches fix the problem.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Adrian Hunter <ext-adrian.hunter@nokia.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: James Morris <jmorris@namei.org>
The LPT may have gaps in it because initially empty LEBs
are not added by mkfs.ubifs - because it does not know how
many there are. Then UBIFS allocates empty LEBs in the
reverse order that they are discovered i.e. they are
added to, and removed from, the front of a list. That
creates a gap in the middle of the LPT.
The function dirtying the LPT tree (for the purpose of
small model garbage collection) assumed that a gap could
only occur at the very end of the LPT and stopped dirtying
prematurely, which in turn resulted in the LPT running
out of space - something that is designed to be impossible.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
We print 'ino_t' type using '%lu' printk() placeholder, but this
results in many warnings when compiling for Alpha platform. Fix
this by adding (unsingned long) casts.
Fixes these warnings:
fs/ubifs/journal.c:693: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/journal.c:1131: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/dir.c:163: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/tnc.c:2680: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/tnc.c:2700: warning: format '%lu' expects type 'long unsigned int', but argument 5 has type 'ino_t'
fs/ubifs/replay.c:1066: warning: format '%lu' expects type 'long unsigned int', but argument 7 has type 'ino_t'
fs/ubifs/orphan.c:108: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/orphan.c:135: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/orphan.c:142: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/orphan.c:154: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/orphan.c:159: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/orphan.c:451: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/orphan.c:539: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/orphan.c:612: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/orphan.c:843: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/orphan.c:856: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/recovery.c:1438: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/recovery.c:1443: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/recovery.c:1475: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/recovery.c:1495: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/debug.c:105: warning: format '%lu' expects type 'long unsigned int', but argument 3 has type 'ino_t'
fs/ubifs/debug.c:105: warning: format '%lu' expects type 'long unsigned int', but argument 3 has type 'ino_t'
fs/ubifs/debug.c:110: warning: format '%lu' expects type 'long unsigned int', but argument 3 has type 'ino_t'
fs/ubifs/debug.c:110: warning: format '%lu' expects type 'long unsigned int', but argument 3 has type 'ino_t'
fs/ubifs/debug.c:114: warning: format '%lu' expects type 'long unsigned int', but argument 3 has type 'ino_t'
fs/ubifs/debug.c:114: warning: format '%lu' expects type 'long unsigned int', but argument 3 has type 'ino_t'
fs/ubifs/debug.c:118: warning: format '%lu' expects type 'long unsigned int', but argument 3 has type 'ino_t'
fs/ubifs/debug.c:118: warning: format '%lu' expects type 'long unsigned int', but argument 3 has type 'ino_t'
fs/ubifs/debug.c:1591: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/debug.c:1671: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/debug.c:1674: warning: format '%lu' expects type 'long unsigned int', but argument 5 has type 'ino_t'
fs/ubifs/debug.c:1680: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/debug.c:1699: warning: format '%lu' expects type 'long unsigned int', but argument 5 has type 'ino_t'
fs/ubifs/debug.c:1788: warning: format '%lu' expects type 'long unsigned int', but argument 5 has type 'ino_t'
fs/ubifs/debug.c:1821: warning: format '%lu' expects type 'long unsigned int', but argument 5 has type 'ino_t'
fs/ubifs/debug.c:1833: warning: format '%lu' expects type 'long unsigned int', but argument 5 has type 'ino_t'
fs/ubifs/debug.c:1924: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/debug.c:1932: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/debug.c:1938: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/debug.c:1945: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/debug.c:1953: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/debug.c:1960: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/debug.c:1967: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/debug.c:1973: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/debug.c:1988: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'ino_t'
fs/ubifs/debug.c:1991: warning: format '%lu' expects type 'long unsigned int', but argument 5 has type 'ino_t'
fs/ubifs/debug.c:2009: warning: format '%lu' expects type 'long unsigned int', but argument 2 has type 'ino_t'
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Noticed by sparse:
fs/ubifs/file.c:75:2: warning: restricted __le64 degrades to integer
fs/ubifs/file.c:629:4: warning: restricted __le64 degrades to integer
fs/ubifs/dir.c:431:3: warning: restricted __le64 degrades to integer
This should be checked to ensure the ubifs_assert is working as
intended, I've done the suggested annotation in this patch.
fs/ubifs/sb.c:298:6: warning: incorrect type in assignment (different base types)
fs/ubifs/sb.c:298:6: expected int [signed] [assigned] tmp
fs/ubifs/sb.c:298:6: got restricted __le64 [usertype] <noident>
fs/ubifs/sb.c:299:19: warning: incorrect type in assignment (different base types)
fs/ubifs/sb.c:299:19: expected restricted __le64 [usertype] atime_sec
fs/ubifs/sb.c:299:19: got int [signed] [assigned] tmp
fs/ubifs/sb.c:300:19: warning: incorrect type in assignment (different base types)
fs/ubifs/sb.c:300:19: expected restricted __le64 [usertype] ctime_sec
fs/ubifs/sb.c:300:19: got int [signed] [assigned] tmp
fs/ubifs/sb.c:301:19: warning: incorrect type in assignment (different base types)
fs/ubifs/sb.c:301:19: expected restricted __le64 [usertype] mtime_sec
fs/ubifs/sb.c:301:19: got int [signed] [assigned] tmp
This looks like a bugfix as your tmp was a u32 so there was truncation in
the atime, mtime, ctime value, probably not intentional, add a tmp_le64
and use it here.
fs/ubifs/key.h:348:9: warning: cast to restricted __le32
fs/ubifs/key.h:348:9: warning: cast to restricted __le32
fs/ubifs/key.h:419:9: warning: cast to restricted __le32
Read from the annotated union member instead.
fs/ubifs/recovery.c:175:13: warning: incorrect type in assignment (different base types)
fs/ubifs/recovery.c:175:13: expected unsigned int [unsigned] [usertype] save_flags
fs/ubifs/recovery.c:175:13: got restricted __le32 [usertype] flags
fs/ubifs/recovery.c:186:13: warning: incorrect type in assignment (different base types)
fs/ubifs/recovery.c:186:13: expected restricted __le32 [usertype] flags
fs/ubifs/recovery.c:186:13: got unsigned int [unsigned] [usertype] save_flags
Do byteshifting at compile time of the flag value. Annotate the saved_flags
as le32.
fs/ubifs/debug.c:368:10: warning: cast to restricted __le32
fs/ubifs/debug.c:368:10: warning: cast from restricted __le64
Should be checked if the truncation was intentional, I've changed the
printk to print the full width.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Remove the "UBIFS background thread ubifs_bgd0_0 started" message.
We kill the background thread when we switch to R/O mode, and
start it again whan we switch to R/W mode. OLPC is doing this
many times during boot, and we see this message many times as
well, which is irritating. So just kill the message.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
* 'linux-next' of git://git.infradead.org/ubifs-2.6: (25 commits)
UBIFS: fix ubifs_compress commentary
UBIFS: amend printk
UBIFS: do not read unnecessary bytes when unpacking bits
UBIFS: check buffer length when scanning for LPT nodes
UBIFS: correct condition to eliminate unecessary assignment
UBIFS: add more debugging messages for LPT
UBIFS: fix bulk-read handling uptodate pages
UBIFS: improve garbage collection
UBIFS: allow for sync_fs when read-only
UBIFS: commit on sync_fs
UBIFS: correct comment for commit_on_unmount
UBIFS: update dbg_dump_inode
UBIFS: fix commentary
UBIFS: fix races in bit-fields
UBIFS: ensure data read beyond i_size is zeroed out correctly
UBIFS: correct key comparison
UBIFS: use bit-fields when possible
UBIFS: check data CRC when in error state
UBIFS: improve znode splitting rules
UBIFS: add no_chk_data_crc mount option
...
Update the comment for ubifs_compress(), which incorrectly states that it
returnsa success/failure indicator.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
It is better to print "Reserved for root" than
"Reserved pool size", because it is more obvious for users
what this means.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This is a much better version of a previous patch to make the parser
tables constant. Rather than changing the typedef, we put the "const" in
all the various places where its required, allowing the __initconst
exception for nfsroot which was the cause of the previous trouble.
This was posted for review some time ago and I believe its been in -mm
since then.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Cc: Alexander Viro <aviro@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Also add debugging checks for LPT size and separate
out c->check_lpt_free from unrelated bitfields.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Bulk-read skips uptodate pages but this was putting its
array index out and causing it to treat subsequent pages
as holes.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Make garbage collection try to keep data nodes from the same
inode together and in ascending order. This improves
performance when reading those nodes especially when bulk-read
is used.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
sync_fs can be called even if the file system is mounted
read-only. Ensure the commit is not run in that case.
Reported-by: Zoltan Sogor <weth@inf.u-szeged.hu>
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Commit the journal when the FS is sync'ed. This will make
statfs provide better free space report. And we anyway
advice our users to sync the FS if they want better statfs
report.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
We cannot store bit-fields together if the processes which
change them may race, unless we serialize them.
Thus, move the nospc and nospc_rp bit-fields eway from
the mount option/constant bit-fields, to avoid races.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The "bulk_read" and "no_chk_data_crc" have only 2 values -
0 and 1. We already have bit-fields in corresponding data
structers, so make "bulk_read" and "no_chk_data_crc"
bit-fields as well.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When UBIFS switches to R/O mode because of an error,
it is reasonable to enable data CRC checking.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When inserting into a full znode it is split into two
znodes. Because data node keys are usually consecutive,
it is better to try to keep them together. This patch
does a better job of that.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
UBIFS read performance can be improved by skipping the CRC
check when data nodes are read. This option can be used if
the underlying media is considered to be highly reliable.
Note that CRCs are always checked for metadata.
Read speed on Arm platform with OneNAND goes from 19 MiB/s
to 27 MiB/s with data CRC checking disabled.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Some flash media are capable of reading sequentially at faster rates.
UBIFS bulk-read facility is designed to take advantage of that, by
reading in one go consecutive data nodes that are also located
consecutively in the same LEB.
Read speed on Arm platform with OneNAND goes from 17 MiB/s to
19 MiB/s.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
In case of error, the function kthread_create returns an ERR pointer,
but never returns a NULL pointer. So a NULL test that comes before an
IS_ERR test should be deleted.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@match_bad_null_test@
expression x, E;
statement S1,S2;
@@
x = kthread_create(...)
... when != x = E
* if (x == NULL)
S1 else S2
// </smpl>
Signed-off-by: Julien Brunel <brunel@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
'ubifs_get_lprops()' and 'ubifs_release_lprops()' basically wrap
mutex lock and unlock. We have them because we want lprops subsystem
be separate and as independent as possible. And we planned better
locking rules for lprops.
Anyway, because they are short, it is better to inline them.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
IS_ERR() macro already has unlikely(), so do not use constructions
like 'if (unlikely(IS_ERR())'.
Signed-off-by: Hirofumi Nakagawa <hnakagawa@miraclelinux.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This commit adds a reserved pool size print and tweaks the
prints to make them look nicer.
It also fixes and cleans-up some comments.
Additionally, it deletes some blank lines to make the code look
a little nicer.
In other words, nothing essential.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Artem Bityutskiy