Remove the atomic counter for slab_reclaim_pages and replace the counter
and NR_SLAB with two ZVC counter that account for unreclaimable and
reclaimable slab pages: NR_SLAB_RECLAIMABLE and NR_SLAB_UNRECLAIMABLE.
Change the check in vmscan.c to refer to to NR_SLAB_RECLAIMABLE. The
intend seems to be to check for slab pages that could be freed.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We cannot check MAX_NR_ZONES since it not defined in the preprocessor
anymore.
So remove the check.
The maximum number of zones per node for i386 is 3 since i386 does not
support ZONE_DMA32.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix array initialization in lots of arches
The number of zones may now be reduced from 4 to 2 for many arches. Fix the
array initialization for the zones array for all architectures so that it is
not initializing a fixed number of elements.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I keep seeing zones on various platforms that are never used and wonder why we
compile support for them into the kernel. Counters show up for HIGHMEM and
DMA32 that are alway zero.
This patch allows the removal of ZONE_DMA32 for non x86_64 architectures and
it will get rid of ZONE_HIGHMEM for arches not using highmem (like 64 bit
architectures). If an arch does not define CONFIG_HIGHMEM then ZONE_HIGHMEM
will not be defined. Similarly if an arch does not define CONFIG_ZONE_DMA32
then ZONE_DMA32 will not be defined.
No current architecture uses all the 4 zones (DMA,DMA32,NORMAL,HIGH) that we
have now. The patchset will reduce the number of zones for all platforms.
On many platforms that do not have DMA32 or HIGHMEM this will reduce the
number of zones by 50%. F.e. ia64 only uses DMA and NORMAL.
Large amounts of memory can be saved for larger systemss that may have a few
hundred NUMA nodes.
With ZONE_DMA32 and ZONE_HIGHMEM support optional MAX_NR_ZONES will be 2 for
many non i386 platforms and even for i386 without CONFIG_HIGHMEM set.
Tested on ia64, x86_64 and on i386 with and without highmem.
The patchset consists of 11 patches that are following this message.
One could go even further than this patchset and also make ZONE_DMA optional
because some platforms do not need a separate DMA zone and can do DMA to all
of memory. This could reduce MAX_NR_ZONES to 1. Such a patchset will
hopefully follow soon.
This patch:
Fix strange uses of MAX_NR_ZONES
Sometimes we use MAX_NR_ZONES - x to refer to a zone. Make that explicit.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Address a long standing issue of booting with an initrd on an i386 numa
system. Currently (and always) the numa kva area is mapped into low memory
by finding the end of low memory and moving that mark down (thus creating
space for the kva). The issue with this is that Grub loads initrds into
this similar space so when the kernel check the initrd it finds it outside
max_low_pfn and disables it (it thinks the initrd is not mapped into usable
memory) thus initrd enabled kernels can't boot i386 numa :(
My solution to the problem just converts the numa kva area to use the
bootmem allocator to save it's area (instead of moving the end of low
memory). Using bootmem allows the kva area to be mapped into more diverse
addresses (not just the end of low memory) and enables the kva area to be
mapped below the initrd if present.
I have tested this patch on numaq(no initrd) and summit(initrd) i386 numa
based systems.
[akpm@osdl.org: cleanups]
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If there is only 1 node in the system cpus should think they are apart of
some other node.
If cases where a real numa system boots the Flat numa option make sure the
cpus don't claim to be apart on a non-existent node.
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With CONFIG_PHYSICAL_START set to a non default values the i386
boot_ioremap code calculated its pte index wrong and users of boot_ioremap
have their areas incorrectly mapped (for me SRAT table not mapped during
early boot). This patch removes the addr < BOOT_PTE_PTRS constraint.
[ Keith says this is applicable to 2.6.16 and 2.6.17 as well ]
Signed-off-by: Keith Mannthey<kmannth@us.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: <stable@kernel.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] sw_any_bug_dmi_table can be used on resume, so it isn't initdata
[CPUFREQ] Fix some more CPU hotplug locking.
[CPUFREQ] Workaround for BIOS bug in software coordination of frequency
[CPUFREQ] Longhaul - Add voltage scaling to driver
[CPUFREQ] Fix sparse warning in ondemand
[CPUFREQ] make drivers/cpufreq/cpufreq_ondemand.c:powersave_bias_target() static
[CPUFREQ] Longhaul - Add ignore_latency option
[CPUFREQ] Longhaul - Disable arbiter
[CPUFREQ][2/2] ondemand: updated add powersave_bias tunable
[CPUFREQ][1/2] ondemand: updated tune for hardware coordination
[CPUFREQ] Fix typo.
sw_any_bug_dmi_table can be used on resume, so it isn't initdata.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Now that the tfm is passed directly to setkey instead of the ctx, we no
longer need to pass the &tfm->crt_flags pointer.
This patch also gets rid of a few unnecessary checks on the key length
for ciphers as the cipher layer guarantees that the key length is within
the bounds specified by the algorithm.
Rather than testing dia_setkey every time, this patch does it only once
during crypto_alloc_tfm. The redundant check from crypto_digest_setkey
is also removed.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This reverts commits 11012d419c and
40dd2d20f2, which allowed us to use the
MMIO accesses for PCI config cycles even without the area being marked
reserved in the e820 memory tables.
Those changes were needed for EFI-environment Intel macs, but broke some
newer Intel 965 boards, so for now it's better to revert to our old
2.6.17 behaviour and at least avoid introducing any new breakage.
Andi Kleen has a set of patches that work with both EFI and the broken
Intel 965 boards, which will be applied once they get wider testing.
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Edgar Hucek <hostmaster@ed-soft.at>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(And reset it on new thread creation)
It turns out that eflags is important to save and restore not just
because of iopl, but due to the magic bits like the NT bit, which we
don't want leaking between different threads.
Tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Take default arch/*/kernel/audit.c to lib/, have those with special
needs (== biarch) define AUDIT_ARCH in their Kconfig.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Some buggy BIOSes do a "software any" kind of coordination without telling
about it to OS. So, when OS sets frequency on one CPU on these platforms,
it will also impact all the other logical CPUs that are in the same power
domain. Attached patch is a workaround for those buggy BIOSes.
Patch should be a noop on the normal non-buggy platforms.
Applies over previously sent acpi-cpufreq and software coordination
bug fix patch
Signed-off-by: Denis Sadykov <denis.m.sadykov@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Rename option "dont_scale_voltage" to "scale_voltage" because
don't will be default.
Use "pos" for calculating voltage. In this way driver don't need
to know mV value or low level value. Simply min U is one pos and
max U is second pos. All pos between these two are used.
Assume that min U is for min f and max U for max f. For frequency
between min and max calculate pos based on difference between
current frequency and min f.
Values in mobile VRM table changed to values from
C3-M datasheet.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Apparently some systems export valid HPET addresses, but hpet_enable()
fails. Then when the HPET clocksource starts up, it only checks for a
valid HPET address, and the result is a system where time does not advance.
See http://bugme.osdl.org/show_bug.cgi?id=7062 for details.
This patch just makes sure we better check that the HPET is functional
before registering the HPET clocksource.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was a bogus hunk from the genirq merge that essentially
broke stack switching for hard interrupts. Remove it since it isn't
needed.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As a replacement for the earlier removal of the e820 MCFG check
we blacklist the Intel SDV with the original BIOS bug that
motivated that check. On those machines don't use MMCONFIG.
This also adds a new pci=mmconf parameter to override the blacklist.
Cc: Greg KH <gregkh@suse.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The unwinder fallback logic still had potential for falling through to
the legacy stack trace code without printing an indication (at once
serving as a separator) of this.
Further, the stack pointer retrieval for the fallback should be as
restrictive as possible (in order to avoid having the legacy stack
tracer try to access invalid memory). The patch tightens that, but
this could certainly be further improved.
Also making the call_trace command line option now conditional upon
CONFIG_STACK_UNWIND (as it's meaningless otherwise).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One open question: Should this added push perhaps be made conditional
upon CONFIG_STACK_UNWIND or CONFIG_UNWIND_INFO?
[AK: not needed, these are all very slow paths]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The check for the MCFG table being reserved in the e820 map was originally
added to detect a broken BIOS in a preproduction Intel SDV. However it also
breaks the Apple x86 Macs, which can't supply this properly, but need
a working MCFG. With this patch they wouldn't use the MCFG and not work.
After some discussion I think it's best to remove the heuristic again.
It also failed on some other boxes (although it didn't cause much
problems there because old style port access for PCI config space
still works as fallback), but the preproduction SDVs can just use
pci=nommcfg. Supporting production machines properly is more
important.
Edgar Hucek did all the debugging work.
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Edgar Hucek <hostmaster@ed-soft.at>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we select NUMA with i386, the system is only X86_NUMAQ or using ACPI.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ignore the return value of early_init_acpi(), as it can give false error
messages. If there is something really wrong, then register_driver will
fail cleanly with EINVAL later.
[ background: modprobe acpi-cpufreq on systems not capable of speed-scaling
started failing with 'invalid argument', where previously it would only
ever -ENODEV
I'm not 100% happy with the solution. It'd be better to handle
failure properly, but this is a low-impact change for 2.6.18
We can always revisit doing this better in .19 --davej.]
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On i386 PCI mmconfig forgets the bus number when setting the fallback_slots
bits which means fallback to conf1 only works for bus 0.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
there was a change in 2.6.17 which affected the order in which the PCI
access methods are probed. this gives regressions on some machines with
broken BIOS. the problem is that PCBIOS sometimes reports last bus wrong,
leaving cardbus non-funcational. previously those system worked fine with
direct access.
The patch changes the PCI init code to have PCBIOS as last fallback, yet
the PCBIOS code still has to run first to set pcibios_last_bus to the value
reported by the BIOS. this is needed in case legacy PCI probing
(arch/i386/pci/legacy.c) is used to detect peer busses. using direct
access if available fixes the cardbus problems.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ACPI 3.0 appended a variable length UID string to the LAPIC structure
as part of support for > 256 processors. So the BAD_MADT_ENTRY() sanity
check can no longer compare for equality with a fixed structure length.
Signed-off-by: Alexey Y Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
A BIOS has been found that resumes from S3 to the routine that invoked suspend,
ignoring the resume vector. This appears to the OS as a failed S3 attempt.
This same system suspend/resume's properly with Windows.
It is possible to invoke the protected mode register restore routine (which
would normally restore the sysenter registers) when the BIOS returns from
S3. This has no effect on a correctly running system and repairs the
damage from the deviant BIOS.
Signed-off-by: William Morrow <william.morrow@amd.com>
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously the message was "Fatal exception: panic_on_oops", as introduced
in a recent patch whith removed a somewhat dangerous call to ssleep() in
the panic_on_oops path. However, Paul Mackerras suggested that this was
somewhat confusing, leadind people to believe that it was panic_on_oops
that was the root cause of the fatal exception. On his suggestion, this
patch changes the message to simply "Fatal exception". A suitable oops
message should already have been displayed.
Signed-off-by: Simon Horman <horms@verge.net.au>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some laptops with VIA C3 processor, CLE266 chipset and
AMI BIOS have incorrect latency values in FADT table. These
laptops seems to be C3 capable, but latency values are to
big: 101 for C2 and 1017 for C3. This option will allow
user to skip C3 latency test but not C3 address test. AMI
BIOS is setting C3 address to correct value in DSDT table.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
ACPI C3 works for "Powersaver" processors, so use it only for them.
Older CPU will change frequency on "halt" only. But we can protect transition
in two ways:
- by ACPI PM2 register, there is "bus master arbiter disable" bit.
This isn't tested because VIA mainboards don't have PM2 register,
- by PLE133 PCI/AGP arbiter disable register.
There are two bits in this register. First is "PCI arbiter disable",
second "AGP arbiter disable". This is working on VIA Epia 800 mainboards.
Test on bm_control is more proper because this is true
when PM2 register exist.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Note how any error from acpi_processor_preregister_performance is ignored.
From: bert hubert <bert.hubert@netherlabs.nl>
Signed-off-by: Dave Jones <davej@redhat.com>
This table is only used by Ezra-T CPUs currently, and has values
for some other CPU. Fix them to match the values used by that CPU,
and for now make it clearer by renaming the variable.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
This is changing "always true" test to something usefull.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch makes the needlessly global longhaul_walk_callback() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Jones <davej@redhat.com>
It seems commit 32ee8c3e47 accidentially
reverted cdc9cc1d74, IOW, it reintroduced
the following compile error with CONFIG_PCI=n:
<-- snip -->
...
CC arch/i386/kernel/cpu/cpufreq/gx-suspmod.o
arch/i386/kernel/cpu/cpufreq/gx-suspmod.c: In function ‘gx_detect_chipset’:
arch/i386/kernel/cpu/cpufreq/gx-suspmod.c:193: error: implicit declaration of function ‘pci_match_id’
arch/i386/kernel/cpu/cpufreq/gx-suspmod.c:193: warning: comparison between pointer and integer
make[3]: *** [arch/i386/kernel/cpu/cpufreq/gx-suspmod.o] Error 1
<-- snip -->
This patch therefore re-adds the dependency of X86_GX_SUSPMOD on PCI.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Without this longhaul will always fail when compiled into kernel,
as it needs to initialise after the ACPI processor module.
I lost this when I was splitting patches. Sorry.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
There is no need to worry about local APIC.
There is need to worry about I/O APIC, because I/O APIC
is replacing good old 8259. According to Nehemiah datasheet VIA is
using 3-wire bus to connect local APIC to I/O APIC.
"[...] When IA32_APIC_BASE[11] is set to 0, processor APICs based on the 3-wire APIC
bus cannot be generally re-enabled until a system hardware reset. The 3-wire bus
looses track of arbitration that would be necessary for complete re-enabling. Certain
(local) APIC functionality can be enabled. [...]"
So we must set disable bit for each interrupt in I/O APIC registers.
Same situation as for PIC - we must poke registers direcly.
How to do this? I don't know. So at the moment it is better to fail.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Minimal change necessary for hardware support.
Changes in longhaul.c:
- most important - now C3 state is causing transition,
- code responsible for clearing "bus master" bit removed,
- protect bcr2 transition in the same way as longhaul.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
CFA needs to be adjusted upwards for push, and downwards for pop.
arch/i386/kernel/entry.S gets it wrong in one place.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The latest toolchains can produce a new ELF section in DSOs and
dynamically-linked executables. The new section ".gnu.hash" replaces
".hash", and allows for more efficient runtime symbol lookups by the
dynamic linker. The new ld option --hash-style={sysv|gnu|both} controls
whether to produce the old ".hash", the new ".gnu.hash", or both. In some
new systems such as Fedora Core 6, gcc by default passes --hash-style=gnu
to the linker, so that a standard invocation of "gcc -shared" results in
producing a DSO with only ".gnu.hash". The new ".gnu.hash" sections need
to be dealt with the same way as ".hash" sections in all respects; only the
dynamic linker cares about their contents. To work with older dynamic
linkers (i.e. preexisting releases of glibc), a binary must have the old
".hash" section. The --hash-style=both option produces binaries that a new
dynamic linker can use more efficiently, but an old dynamic linker can
still handle.
The new section runs afoul of the custom linker scripts used to build vDSO
images for the kernel. On ia64, the failure mode for this is a boot-time
panic because the vDSO's PT_IA_64_UNWIND segment winds up ill-formed.
This patch addresses the problem in two ways.
First, it mentions ".gnu.hash" in all the linker scripts alongside ".hash".
This produces correct vDSO images with --hash-style=sysv (or old tools),
with --hash-style=gnu, or with --hash-style=both.
Second, it passes the --hash-style=sysv option when building the vDSO
images, so that ".gnu.hash" is not actually produced. This is the most
conservative choice for compatibility with any old userland. There is some
concern that some ancient glibc builds (though not any known old production
system) might choke on --hash-style=both binaries. The optimizations
provided by the new style of hash section do not really matter for a DSO
with a tiny number of symbols, as the vDSO has. If someone wants to use
=gnu or =both for their vDSO builds and worry less about that
compatibility, just change the option and the linker script changes will
make any choice work fine.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use hotplug version of register_cpu_notifier in late init functions.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is part of an effort to unify the panic_on_oops behaviour across
all architectures that implement it.
It was pointed out to me by Andi Kleen that if an oops has occured in
interrupt context, then calling sleep() in the oops path will only cause a
panic, and that it would be really better for it not to be in the path at
all.
This patch removes the ssleep() call and reworks the console message
accordinly. I have a slght concern that the resulting console message is
too long, feedback welcome.
For powerpc it also unifies the 32bit and 64bit behaviour.
Fror x86_64, this patch only updates the console message, as ssleep() is
already not present.
Signed-off-by: Horms <horms@verge.net.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When resuming from suspend-to-RAM, the NMI watchdog detects a lockup in
ide_wait_not_busy. Here's a screenshot of the trace taken by a digital
camera: http://www.uamt.feec.vutbr.cz/rizeni/pom/DSC03510-2.JPG
Let's touch the NMI watchdog in ide_wait_not_busy. The system then resumes
correctly from STR.
[akpm@osdl.org: modular build fix]
Signed-off-by: Michal Schmidt <xschmi00@stud.feec.vutbr.cz>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Christoph Lameter
keith mannthey
Linus Torvalds
Jeremy Fitzhardinge
Herbert Xu
Joachim Fritschi
Benjamin LaHaise
Al Viro
Venkatesh Pallipadi
Rafa³ Bilski
Dave Jones
john stultz
Andi Kleen
Jan Beulich
KAMEZAWA Hiroyuki
Daniel Ritz
Len Brown
Starikovskiy, Alexey Y
William Morrrow
Horms
bert hubert
Adrian Bunk
Markus Armbruster
Roland McGrath
Chandra Seetharaman
Michal Schmidt
