Pull pile 2 of execve and kernel_thread unification work from Al Viro:
"Stuff in there: kernel_thread/kernel_execve/sys_execve conversions for
several more architectures plus assorted signal fixes and cleanups.
There'll be more (in particular, real fixes for the alpha
do_notify_resume() irq mess)..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (43 commits)
alpha: don't open-code trace_report_syscall_{enter,exit}
Uninclude linux/freezer.h
m32r: trim masks
avr32: trim masks
tile: don't bother with SIGTRAP in setup_frame
microblaze: don't bother with SIGTRAP in setup_rt_frame()
mn10300: don't bother with SIGTRAP in setup_frame()
frv: no need to raise SIGTRAP in setup_frame()
x86: get rid of duplicate code in case of CONFIG_VM86
unicore32: remove pointless test
h8300: trim _TIF_WORK_MASK
parisc: decide whether to go to slow path (tracesys) based on thread flags
parisc: don't bother looping in do_signal()
parisc: fix double restarts
bury the rest of TIF_IRET
sanitize tsk_is_polling()
bury _TIF_RESTORE_SIGMASK
unicore32: unobfuscate _TIF_WORK_MASK
mips: NOTIFY_RESUME is not needed in TIF masks
mips: merge the identical "return from syscall" per-ABI code
...
Conflicts:
arch/arm/include/asm/thread_info.h
the only non-obvious part is that current_pt_regs() is really needed
here - task_pt_regs() is NULL for kernel threads; it's OK for ptrace
uses (the thing task_pt_regs() is intended for), but not for us.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We can't emulate stwu since that may corrupt current exception stack.
So we will have to do real store operation in the exception return code.
Firstly we'll allocate a trampoline exception frame below the kprobed
function stack and copy the current exception frame to the trampoline.
Then we can do this real store operation to implement 'stwu', and reroute
the trampoline frame to r1 to complete this exception migration.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During a context switch we always restore the per thread DSCR value.
If we aren't doing explicit DSCR management
(ie thread.dscr_inherit == 0) and the default DSCR changed while
the process has been sleeping we end up with the wrong value.
Check thread.dscr_inherit and select the default DSCR or per thread
DSCR as required.
This was found with the following test case, when running with
more threads than CPUs (ie forcing context switching):
http://ozlabs.org/~anton/junkcode/dscr_default_test.c
With the four patches applied I can run a combination of all
test cases successfully at the same time:
http://ozlabs.org/~anton/junkcode/dscr_default_test.chttp://ozlabs.org/~anton/junkcode/dscr_explicit_test.chttp://ozlabs.org/~anton/junkcode/dscr_inherit_test.c
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
mtmsrd is an expensive instruction, we save a few cycles by
doing it once instead of twice.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In entry_64.S version of ret_from_except_lite, you'll notice that
in the !preempt case, after we've checked MSR_PR we test for any
TIF flag in _TIF_USER_WORK_MASK to decide whether to go to do_work
or not. However, in the preempt case, we do a convoluted trick to
test SIGPENDING only if PR was set and always test NEED_RESCHED ...
but we forget to test any other bit of _TIF_USER_WORK_MASK !!! So
that means that with preempt, we completely fail to test for things
like single step, syscall tracing, etc...
This should be fixed as the following path:
- Test PR. If not set, go to resume_kernel, else continue.
- If go resume_kernel, to do that original do_work.
- If else, then always test for _TIF_USER_WORK_MASK to decide to do
that original user_work, else restore directly.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
So we have another case of paca->irq_happened getting out of
sync with the HW irq state. This can happen when a perfmon
interrupt occurs while soft disabled, as it will return to a
soft disabled but hard enabled context while leaving a stale
PACA_IRQ_HARD_DIS flag set.
This patch fixes it, and also adds a test for the condition
of those flags being out of sync in arch_local_irq_restore()
when CONFIG_TRACE_IRQFLAGS is enabled.
This helps catching those gremlins faster (and so far I
can't seem see any anymore, so that's good news).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We had a case where we could turn on hard interrupts while
leaving the PACA_IRQ_HARD_DIS bit set in the PACA. This can
in turn cause a BUG_ON() to hit in __check_irq_replay() due
to interrupt state getting out of sync.
The assembly code was also way too convoluted. Instead, we
now leave it to the C code to do the right thing which ends
up being smaller and more readable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At the moment system call entry looks like:
crclr so
...
mfcr r9
...
std r9,_CCR(r1)
commit bd19c8994a ([POWERPC] system call micro optimisation) put
some space between the crclr and mfcr in order to avoid a stall.
There is still a stall seen between the mfcr and std. We can avoid
the crclr by doing it in a GPR with rlwinm which gives us more room
to better schedule the sequence.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The count register is volatile so we don't need to preserve it.
Store zero to the entry in the exception frame.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The XER is a volatile register so there is no need to save and restore
it over a system call - zero it out in the exception stack frame
instead.
This should fix a 5 cycle stall of the mfxer/std seen on POWER7.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
syscall_dotrace_cont and syscall_error_cont tend to complicate perf
output so make them local.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current implementation of lazy interrupts handling has some
issues that this tries to address.
We don't do the various workarounds we need to do when re-enabling
interrupts in some cases such as when returning from an interrupt
and thus we may still lose or get delayed decrementer or doorbell
interrupts.
The current scheme also makes it much harder to handle the external
"edge" interrupts provided by some BookE processors when using the
EPR facility (External Proxy) and the Freescale Hypervisor.
Additionally, we tend to keep interrupts hard disabled in a number
of cases, such as decrementer interrupts, external interrupts, or
when a masked decrementer interrupt is pending. This is sub-optimal.
This is an attempt at fixing it all in one go by reworking the way
we do the lazy interrupt disabling from the ground up.
The base idea is to replace the "hard_enabled" field with a
"irq_happened" field in which we store a bit mask of what interrupt
occurred while soft-disabled.
When re-enabling, either via arch_local_irq_restore() or when returning
from an interrupt, we can now decide what to do by testing bits in that
field.
We then implement replaying of the missed interrupts either by
re-using the existing exception frame (in exception exit case) or via
the creation of a new one from an assembly trampoline (in the
arch_local_irq_enable case).
This removes the need to play with the decrementer to try to create
fake interrupts, among others.
In addition, this adds a few refinements:
- We no longer hard disable decrementer interrupts that occur
while soft-disabled. We now simply bump the decrementer back to max
(on BookS) or leave it stopped (on BookE) and continue with hard interrupts
enabled, which means that we'll potentially get better sample quality from
performance monitor interrupts.
- Timer, decrementer and doorbell interrupts now hard-enable
shortly after removing the source of the interrupt, which means
they no longer run entirely hard disabled. Again, this will improve
perf sample quality.
- On Book3E 64-bit, we now make the performance monitor interrupt
act as an NMI like Book3S (the necessary C code for that to work
appear to already be present in the FSL perf code, notably calling
nmi_enter instead of irq_enter). (This also fixes a bug where BookE
perfmon interrupts could clobber r14 ... oops)
- We could make "masked" decrementer interrupts act as NMIs when doing
timer-based perf sampling to improve the sample quality.
Signed-off-by-yet: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
v2:
- Add hard-enable to decrementer, timer and doorbells
- Fix CR clobber in masked irq handling on BookE
- Make embedded perf interrupt act as an NMI
- Add a PACA_HAPPENED_EE_EDGE for use by FSL if they want
to retrigger an interrupt without preventing hard-enable
v3:
- Fix or vs. ori bug on Book3E
- Fix enabling of interrupts for some exceptions on Book3E
v4:
- Fix resend of doorbells on return from interrupt on Book3E
v5:
- Rebased on top of my latest series, which involves some significant
rework of some aspects of the patch.
v6:
- 32-bit compile fix
- more compile fixes with various .config combos
- factor out the asm code to soft-disable interrupts
- remove the C wrapper around preempt_schedule_irq
v7:
- Fix a bug with hard irq state tracking on native power7
On 64-bit, the mfmsr instruction can be quite slow, slower
than loading a field from the cache-hot PACA, which happens
to already contain the value we want in most cases.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We unconditionally hard enable interrupts. This is unnecessary as
syscalls are expected to always be called with interrupts enabled.
While at it, we add a WARN_ON if that is not the case and
CONFIG_TRACE_IRQFLAGS is enabled (we don't want to add overhead
to the fast path when this is not set though).
Thus let's remove the enabling (and associated irq tracing) from
the syscall entry path. Also on Book3S, replace a few mfmsr
instructions with loads of PACAMSR from the PACA, which should be
faster & schedule better.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This removes the various bits of assembly in the kernel entry,
exception handling and SLB management code that were specific
to running under the legacy iSeries hypervisor which is no
longer supported.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a few problems when returning to userspace. This is a
quick set of fixes for 3.3, I'll look into a more comprehensive
rework for 3.4. This fixes:
- We kept interrupts soft-disabled when schedule'ing or calling
do_signal when returning to userspace as a result of a hardware
interrupt.
- Rename do_signal to do_notify_resume like all other archs (and
do_signal_pending back to do_signal, which it was before Roland
changed it).
- Add the missing call to key_replace_session_keyring() to
do_notify_resume().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
Some of the 64bit PPC CPU features are MMU-related, so this patch moves
them to MMU_FTR_ bits. All cpu_has_feature()-style tests are moved to
mmu_has_feature(), and seven feature bits are freed as a result.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The DSCR (aka Data Stream Control Register) is supported on some
server PowerPC chips and allow some control over the prefetch
of data streams.
This patch allows the value to be specified per thread by emulating
the corresponding mfspr and mtspr instructions. Children of such
threads inherit the value. Other threads use a default value that
can be specified in sysfs - /sys/devices/system/cpu/dscr_default.
If a thread starts with non default value in the sysfs entry,
all children threads inherit this non default value even if
the sysfs value is changed later.
Signed-off-by: Alexey Kardashevskiy <aik@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When running in Hypervisor mode (arch 2.06 or later), we store the PACA
in HSPRG0 instead of SPRG1. The architecture specifies that SPRGs may be
lost during a "nap" power management operation (though they aren't
currently on POWER7) and this enables use of SPRG1 by KVM guests.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, when CONFIG_VIRT_CPU_ACCOUNTING is enabled, we use the
PURR register for measuring the user and system time used by
processes, as well as other related times such as hardirq and
softirq times. This turns out to be quite confusing for users
because it means that a program will often be measured as taking
less time when run on a multi-threaded processor (SMT2 or SMT4 mode)
than it does when run on a single-threaded processor (ST mode), even
though the program takes longer to finish. The discrepancy is
accounted for as stolen time, which is also confusing, particularly
when there are no other partitions running.
This changes the accounting to use the timebase instead, meaning that
the reported user and system times are the actual number of real-time
seconds that the program was executing on the processor thread,
regardless of which SMT mode the processor is in. Thus a program will
generally show greater user and system times when run on a
multi-threaded processor than on a single-threaded processor.
On pSeries systems on POWER5 or later processors, we measure the
stolen time (time when this partition wasn't running) using the
hypervisor dispatch trace log. We check for new entries in the
log on every entry from user mode and on every transition from
kernel process context to soft or hard IRQ context (i.e. when
account_system_vtime() gets called). So that we can correctly
distinguish time stolen from user time and time stolen from system
time, without having to check the log on every exit to user mode,
we store separate timestamps for exit to user mode and entry from
user mode.
On systems that have a SPURR (POWER6 and POWER7), we read the SPURR
in account_system_vtime() (as before), and then apportion the SPURR
ticks since the last time we read it between scaled user time and
scaled system time according to the relative proportions of user
time and system time over the same interval. This avoids having to
read the SPURR on every kernel entry and exit. On systems that have
PURR but not SPURR (i.e., POWER5), we do the same using the PURR
rather than the SPURR.
This disables the DTL user interface in /sys/debug/kernel/powerpc/dtl
for now since it conflicts with the use of the dispatch trace log
by the time accounting code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The POWER architecture does not require stcx to check that it is operating
on the same address as the larx. This means it is possible for an
an exception handler to execute a larx, get a reservation, decide
not to do the stcx and then return back with an active reservation. If the
interrupted code was in the middle of a larx/stcx sequence the stcx could
incorrectly succeed.
All recent POWER CPUs check the address before letting the stcx succeed
so we can create a CPU feature and nop it out. As Ben suggested, we can
only do this in our syscall path because there is a remote possibility
some kernel code gets interrupted by an exception that ends up operating
on the same cacheline.
Thanks to Paul Mackerras and Derek Williams for the idea.
To test this I used a very simple null syscall (actually getppid) testcase
at http://ozlabs.org/~anton/junkcode/null_syscall.c
I tested against 2.6.35-git10 with the following changes against the
pseries_defconfig:
CONFIG_VIRT_CPU_ACCOUNTING=n
CONFIG_AUDIT=n
CONFIG_PPC_4K_PAGES=n
CONFIG_PPC_64K_PAGES=y
CONFIG_FORCE_MAX_ZONEORDER=9
CONFIG_PPC_SUBPAGE_PROT=n
CONFIG_FUNCTION_TRACER=n
CONFIG_FUNCTION_GRAPH_TRACER=n
CONFIG_IRQSOFF_TRACER=n
CONFIG_STACK_TRACER=n
to remove the overhead of virtual CPU accounting, syscall auditing and
the ftrace mcount tracers. 64kB pages were enabled to minimise TLB misses.
POWER6: +8.2%
POWER7: +7.0%
Another suggestion was to use a larx to something in the L1 instead of a stcx.
This was almost as fast as removing the larx on POWER6, but only 3.5% faster
on POWER7. We can use this to speed up the reservation clear in our
exception exit code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard found that large POWER systems would occasionally
crash in the exception exit path when profiling with perf_events.
The symptom was that an interrupt would occur late in the exit path
when the MSR[RI] (recoverable interrupt) bit was clear. Interrupts
should be hard-disabled at this point but they were enabled. Because
the interrupt was not recoverable the system panicked.
The reason is that the exception exit path was calling
perf_event_do_pending after hard-disabling interrupts, and
perf_event_do_pending will re-enable interrupts.
The simplest and cleanest fix for this is to use the same mechanism
that 32-bit powerpc does, namely to cause a self-IPI by setting the
decrementer to 1. This means we can remove the tests in the exception
exit path and raw_local_irq_restore.
This also makes sure that the call to perf_event_do_pending from
timer_interrupt() happens within irq_enter/irq_exit. (Note that
calling perf_event_do_pending from timer_interrupt does not mean that
there is a possible 1/HZ latency; setting the decrementer to 1 ensures
that the timer interrupt will happen immediately, i.e. within one
timebase tick, which is a few nanoseconds or 10s of nanoseconds.)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
RTAS should never cause an exception but if it does (for example accessing
outside our RMO) then we might go a long way through the kernel before
oopsing. If we unset MSR_RI we should at least stop things on exception
exit.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If CONFIG_PPC_ISERIES isn't defined we end up with
iseries_check_pending_irqs and do_work at the same address.
perf ends up picking iseries_check_pending_irqs which creates
confusing backtraces. Hide it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Based on an original patch by Valentine Barshak <vbarshak@ru.mvista.com>
Use preempt_schedule_irq to prevent infinite irq-entry and
eventual stack overflow problems with fast-paced IRQ sources.
This kind of problems has been observed on the PASemi Electra IDE
controller. We have to make sure we are soft-disabled before calling
preempt_schedule_irq and hard disable interrupts after that
to avoid unrecoverable exceptions.
This patch also moves the "clrrdi r9,r1,THREAD_SHIFT" out of
the #ifdef CONFIG_PPC_BOOK3E scope, since r9 is clobbered
and has to be restored in both cases.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The mod_return_to_handler needs to switch to the kernel TOC before
jumping to a the kernel code. It currently does this by looking
at the kernel function data and retrieves the TOC that way.
Not only is this inefficient, it also breaks with a relocatable kernel.
The PACA contains the kernel TOC and we can easily retrieve it that
way.
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Bye-bye Performance Counters, welcome Performance Events!
In the past few months the perfcounters subsystem has grown out its
initial role of counting hardware events, and has become (and is
becoming) a much broader generic event enumeration, reporting, logging,
monitoring, analysis facility.
Naming its core object 'perf_counter' and naming the subsystem
'perfcounters' has become more and more of a misnomer. With pending
code like hw-breakpoints support the 'counter' name is less and
less appropriate.
All in one, we've decided to rename the subsystem to 'performance
events' and to propagate this rename through all fields, variables
and API names. (in an ABI compatible fashion)
The word 'event' is also a bit shorter than 'counter' - which makes
it slightly more convenient to write/handle as well.
Thanks goes to Stephane Eranian who first observed this misnomer and
suggested a rename.
User-space tooling and ABI compatibility is not affected - this patch
should be function-invariant. (Also, defconfigs were not touched to
keep the size down.)
This patch has been generated via the following script:
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/PERF_EVENT_/PERF_RECORD_/g' \
-e 's/PERF_COUNTER/PERF_EVENT/g' \
-e 's/perf_counter/perf_event/g' \
-e 's/nb_counters/nb_events/g' \
-e 's/swcounter/swevent/g' \
-e 's/tpcounter_event/tp_event/g' \
$FILES
for N in $(find . -name perf_counter.[ch]); do
M=$(echo $N | sed 's/perf_counter/perf_event/g')
mv $N $M
done
FILES=$(find . -name perf_event.*)
sed -i \
-e 's/COUNTER_MASK/REG_MASK/g' \
-e 's/COUNTER/EVENT/g' \
-e 's/\<event\>/event_id/g' \
-e 's/counter/event/g' \
-e 's/Counter/Event/g' \
$FILES
... to keep it as correct as possible. This script can also be
used by anyone who has pending perfcounters patches - it converts
a Linux kernel tree over to the new naming. We tried to time this
change to the point in time where the amount of pending patches
is the smallest: the end of the merge window.
Namespace clashes were fixed up in a preparatory patch - and some
stylistic fallout will be fixed up in a subsequent patch.
( NOTE: 'counters' are still the proper terminology when we deal
with hardware registers - and these sed scripts are a bit
over-eager in renaming them. I've undone some of that, but
in case there's something left where 'counter' would be
better than 'event' we can undo that on an individual basis
instead of touching an otherwise nicely automated patch. )
Suggested-by: Stephane Eranian <eranian@google.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux-arch@vger.kernel.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This contains all the bits that didn't fit in previous patches :-) This
includes the actual exception handlers assembly, the changes to the
kernel entry, other misc bits and wiring it all up in Kconfig.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
enter_prom() used to save and restore registers such as CTR, XER etc..
which are volatile, or SRR0,1... which we don't care about. This
removes a bunch of useless code and while at it turns an mtmsrd into
an MTMSRD macro which will be useful to Book3E.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The kernel uses SPRG registers for various purposes, typically in
low level assembly code as scratch registers or to hold per-cpu
global infos such as the PACA or the current thread_info pointer.
We want to be able to easily shuffle the usage of those registers
as some implementations have specific constraints realted to some
of them, for example, some have userspace readable aliases, etc..
and the current choice isn't always the best.
This patch should not change any code generation, and replaces the
usage of SPRN_SPRGn everywhere in the kernel with a named replacement
and adds documentation next to the definition of the names as to
what those are used for on each processor family.
The only parts that still use the original numbers are bits of KVM
or suspend/resume code that just blindly needs to save/restore all
the SPRGs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Merge reason: we have gathered quite a few conflicts, need to merge upstream
Conflicts:
arch/powerpc/kernel/Makefile
arch/x86/ia32/ia32entry.S
arch/x86/include/asm/hardirq.h
arch/x86/include/asm/unistd_32.h
arch/x86/include/asm/unistd_64.h
arch/x86/kernel/cpu/common.c
arch/x86/kernel/irq.c
arch/x86/kernel/syscall_table_32.S
arch/x86/mm/iomap_32.c
include/linux/sched.h
kernel/Makefile
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The TOCS used by modules are different than the one used by
the core kernel code. The function graph tracer must save and
restore the TOC whenever it traces a module call. But this
is an added overhead to burden the majority of core kernel
code being traced.
Benjamin Herrenschmidt suggested in testing the entry of
the call to tell if it is a core kernel function or a module.
He recommended using the REGION_ID() macro to perform this test.
This patch implements Benjamin's idea, and uses a different
return_to_handler routine dependent on if the entry is a core
kernel function or not. The module version saves the TOC, where as
the core kernel version does not.
Geoff Lavand tested on PS3.
Tested-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is the port of the function graph tracer to PowerPC with
dynamic tracing.
Geoff Lavand tested on PS3.
Tested-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a port of the function graph tracer that was written by
Frederic Weisbecker for the x86.
This only works for PPC64 at the moment and only for static tracing.
PPC32 and dynamic function graph tracing support will come later.
The trace produces a visual calling of functions:
# tracer: function_graph
#
# CPU DURATION FUNCTION CALLS
# | | | | | | |
0) 2.224 us | }
0) ! 271.024 us | }
0) ! 320.080 us | }
0) ! 324.656 us | }
0) ! 329.136 us | }
0) | .put_prev_task_fair() {
0) | .update_curr() {
0) 2.240 us | .update_min_vruntime();
0) 6.512 us | }
0) 2.528 us | .__enqueue_entity();
0) + 15.536 us | }
0) | .pick_next_task_fair() {
0) 2.032 us | .__pick_next_entity();
0) 2.064 us | .__clear_buddies();
0) | .set_next_entity() {
0) 2.672 us | .__dequeue_entity();
0) 6.864 us | }
Geoff Lavand tested on PS3.
Tested-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Because 64-bit powerpc uses lazy (soft) interrupt disabling, it is
possible for a performance monitor exception to come in when the
kernel thinks interrupts are disabled (i.e. when they are
soft-disabled but hard-enabled). In such a situation the performance
monitor exception handler might have some processing to do (such as
process wakeups) which can't be done in what is effectively an NMI
handler.
This provides a way to defer that work until interrupts get enabled,
either in raw_local_irq_restore() or by returning from an interrupt
handler to code that had interrupts enabled. We have a per-processor
flag that indicates that there is work pending to do when interrupts
subsequently get re-enabled. This flag is checked in the interrupt
return path and in raw_local_irq_restore(), and if it is set,
perf_counter_do_pending() is called to do the pending work.
Signed-off-by: Paul Mackerras <paulus@samba.org>
It turns out that on Cell, on a kernel with CONFIG_VIRT_CPU_ACCOUNTING
= y, if a program sets the SO (summary overflow) bit in the XER and
then does a system call, the SO bit in CR0 will be set on return
regardless of whether the system call detected an error. Since CR0.SO
is used as the error indication from the system call, this means that
all system calls appear to fail.
The reason is that the workaround for the timebase bug on Cell uses a
compare instruction. With CONFIG_VIRT_CPU_ACCOUNTING = y, the
ACCOUNT_CPU_USER_ENTRY macro reads the timebase, so we end up doing a
compare instruction, which copies XER.SO to CR0.SO. Since we were
doing this in the system call entry patch after clearing CR0.SO but
before saving the CR, this meant that the saved CR image had CR0.SO
set if XER.SO was set on entry.
This fixes it by moving the clearing of CR0.SO to after the
ACCOUNT_CPU_USER_ENTRY call in the system call entry path.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Impact: quicken mcount calls that are not replaced by dyn ftrace
Dynamic ftrace no longer does on the fly recording of mcount locations.
The mcount locations are now found at compile time. The mcount
function no longer needs to store registers and call a stub function.
It can now just simply return.
Since there are some functions that do not get converted to a nop
(.init sections and other code that may disappear), this patch should
help speed up that code.
Also, the stub for mcount on PowerPC 32 can not be a simple branch
link register like it is on PowerPC 64. According to the ABI specification:
"The _mcount routine is required to restore the link register from
the stack so that the profiling code can be inserted transparently,
whether or not the profiled function saves the link register itself."
This means that we must restore the link register that was used
to make the call to mcount. The minimal mcount function for PPC32
ends up being:
mcount:
mflr r0
mtctr r0
lwz r0, 4(r1)
mtlr r0
bctr
Where we move the link register used to call mcount into the
ctr register, and then restore the link register from the stack.
Then we use the ctr register to jump back to the mcount caller.
The r0 register is free for us to use.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Due to confusion between the ftrace infrastructure and the gcc profiling
tracer "ftrace", this patch renames the config options from FTRACE to
FUNCTION_TRACER. The other two names that are offspring from FTRACE
DYNAMIC_FTRACE and FTRACE_MCOUNT_RECORD will stay the same.
This patch was generated mostly by script, and partially by hand.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Using LOAD_REG_IMMEDIATE to get the address of kernel symbols
generates 5 instructions where LOAD_REG_ADDR can do it in one,
and will generate R_PPC64_ADDR16_* relocations in the output when
we get to making the kernel as a position-independent executable,
which we'd rather not have to handle. This changes various bits
of assembly code to use LOAD_REG_ADDR when we need to get the
address of a symbol, or to use suitable position-independent code
for cases where we can't access the TOC for various reasons, or
if we're not running at the address we were linked at.
It also cleans up a few minor things; there's no reason to save and
restore SRR0/1 around RTAS calls, __mmu_off can get the return
address from LR more conveniently than the caller can supply it in
R4 (and we already assume elsewhere that EA == RA if the MMU is on
in early boot), and enable_64b_mode was using 5 instructions where
2 would do.
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is a small passage of code in ret_from_except_lite which is
only required on iSeries. For a multi-platform kernel on non-iSeries
machines this means we end up executing ~15 nops in ret_from_except_lite.
It would be nicer if non-iSeries could skip the code entirely, and on
iSeries we can jump out of line to execute the code.
I have no performance numbers to justify this, other than the assertion
that executing 15 nops takes longer than executing 0.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds TIF_NOTIFY_RESUME support for powerpc. When set,
we call tracehook_notify_resume() on the way to user mode.
This overloads do_signal() to do the work, but changes its
arguments to it has the TIF_* bits handy in a register and
drops the useless first argument that was always zero.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This changes powerpc syscall tracing to use the new tracehook.h entry
points. There is no change, only cleanup.
In addition, the assembly changes allow do_syscall_trace_enter() to
abort the syscall without losing the information about the original
r0 value.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Li Zhong
Linus Torvalds
Al Viro
Tiejun Chen
Anton Blanchard
Stuart Yoder
Benjamin Herrenschmidt
Matt Evans
Alexey Kardashevskiy
Paul Mackerras
Ingo Molnar
Steven Rostedt
Steven Rostedt
Michael Ellerman
Roland McGrath