Export the information which antennas are available for configuration as TX or
RX antennas via nl80211.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As has been pointed out by Daniel Halperin some devices (e.g. Intel IWL5100)
can only TX from a subset of RX antennas, so use separate availability masks
for RX and TX.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let path selection frames for protocols other than HWMP be sent to
userspace via NL80211_CMD_REGISTER_FRAME. Also allow userspace to send
and receive mesh path selection frames.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Userspace will now be allowed to toggle between the default path
selection algorithm (HWMP, implemented in the kernel), and a vendor
specific alternative. Also in the same patch, allow userspace to add
information elements to mesh beacons. This is accordance with the
Extensible Path Selection Framework specified in version 7.0 of the
802.11s draft.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh parameters can be to setup a mesh or to configure it.
This patch renames the ambiguous name mesh_params to mesh_config
in preparation for mesh_setup.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new notification to indicate that a received, unprotected
Deauthentication or Disassociation frame was dropped due to
management frame protection being in use. This notification is
needed to allow user space (e.g., wpa_supplicant) to implement
SA Query procedure to recover from association state mismatch
between an AP and STA.
This is needed to avoid getting stuck in non-working state when MFP
(IEEE 802.11w) is used and a protected Deauthentication or
Disassociation frame is dropped for any reason. After that, the
station would silently discard any unprotected Deauthentication or
Disassociation frame that could be indicating that the AP does not
have association for the STA (when the Reason Code would be 6 or 7).
IEEE Std 802.11w-2009, 11.13 describes this recovery mechanism.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the upcoming hardware offload implementation,
some devices will have a different maximum duration
for the remain-on-channel command. Advertise the
maximum duration in mac80211, and make mac80211 set
it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to specify that a given key
is default only for unicast and/or multicast
transmissions. Only WEP keys are for both,
WPA/RSN keys set here are GTKs for multicast
only. For more future flexibility, allow to
specify all combiations.
Wireless extensions can only set both so use
nl80211; WEP keys (connect keys) must be set
as default for both (but 802.1X WEP is still
possible).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a field to wiphy for the hardware to report the availble antennas for
configuration. Only if this is set to something bigger than zero, will the
anntenna configuration ops be executed.
Allthough this could be a simple number of antennas, I defined it as a bitmap
of antennas which are available for configuration, since it's more consistent
with the rest of the antenna API and there could be cases where the
hardware allows only configuration of certain antennas. As it does not make
much of a difference in size or normal usage, I think it's better to be able to
support this, in case the need arises.
The antenna configuration is now also checked against the availabe antennas and
rejected if it does not match.
Signed-off-by: Bruno Randolf <br1@einfach.org>
--
v3: always apply available antenna mask (for "all" antennas case).
v2: reject antenna configurations which don't match the available antennas
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new BSS attribute to allow hostapd to set the current HT opmode.
Otherwise drivers won't be able to set up protection for HT rates in
AP mode.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.
This uses the recently added generic EWMA library function.
--
v2: fix ABI breakage and change factor to be a power of 2.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of tying mesh activity to interface up,
add join and leave commands for mesh. Since we
must be backward compatible, let cfg80211 handle
joining a mesh if a mesh ID was pre-configured
when the device goes up.
Note that this therefore must modify mac80211 as
well since mac80211 needs to lose the logic to
start the mesh on interface up.
We now allow querying mesh parameters before the
mesh is connected, which simply returns defaults.
Setting them (internally renamed to "update") is
only allowed while connected. Specify them with
the new mesh join command instead where needed.
In mac80211, beaconing must now also follow the
mesh enabled/not enabled state, which is done
by testing the mesh ID.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I'm going to need this in a new place later.
Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 used to do all its bookkeeping in
the notifier, but some new stuff will have
to use local variables so make the callback
return the netdev pointer.
Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TTL in path selection information elements is different from
the mesh ttl used in mesh data frames. Version 7.03 of the 11s
draft calls this ttl 'Element TTL'.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With p2p, it is sometimes necessary to transmit
a frame (typically an action frame) on another
channel than the current channel. Enable this
through the CMD_FRAME API, and allow it to wait
for a response. A new command allows that wait
to be aborted.
However, allow userspace to specify whether or
not it wants to allow off-channel TX, it may
actually want to use the same channel only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the ability for drivers to use CQM events
to notify about packet loss for specific stations
(which could be the AP for the managed mode case).
Since the threshold might be determined by the
driver (it isn't passed in right now) it will be
passed out of the driver to userspace in the event.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- store the multicast rate as an index instead of the rate value
(reduces cpu overhead in a hotpath)
- validate the rate values (must match a bitrate in at least one sband)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.
This uses the recently added generic EWMA library function.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow setting of TX and RX antennas configuration via nl80211.
The antenna configuration is defined as a bitmap of allowed antennas to use.
This API can be used to mask out antennas which are not attached or should not
be used for other reasons like regulatory concerns or special setups.
Separate bitmaps are used for RX and TX to allow configuring different antennas
for receiving and transmitting. Each bitmap is 32 bit long, each bit
representing one antenna, starting with antenna 1 at the first bit. If an
antenna bit is set, this means the driver is allowed to use this antenna for RX
or TX respectively; if the bit is not set the hardware is not allowed to use
this antenna.
Using bitmaps has the benefit of allowing for a flexible configuration
interface which can support many different configurations and which can be used
for 802.11n as well as non-802.11n devices. Instead of relying on some hardware
specific assumptions, drivers can use this information to know which antennas
are actually attached to the system and derive their capabilities based on
that.
802.11n devices should enable or disable chains, based on which antennas are
present (If all antennas belonging to a particular chain are disabled, the
entire chain should be disabled). HT capabilities (like STBC, TX Beamforming,
Antenna selection) should be calculated based on the available chains after
applying the antenna masks. Should a 802.11n device have diversity antennas
attached to one of their chains, diversity can be enabled or disabled based on
the antenna information.
Non-802.11n drivers can use the antenna masks to select RX and TX antennas and
to enable or disable antenna diversity.
While covering chainmasks for 802.11n and the standard "legacy" modes "fixed
antenna 1", "fixed antenna 2" and "diversity" this API also allows more rare,
but useful configurations as follows:
1) Send on antenna 1, receive on antenna 2 (or vice versa). This can be used to
have a low gain antenna for TX in order to keep within the regulatory
constraints and a high gain antenna for RX in order to receive weaker signals
("speak softly, but listen harder"). This can be useful for building long-shot
outdoor links. Another usage of this setup is having a low-noise pre-amplifier
on antenna 1 and a power amplifier on the other antenna. This way transmit
noise is mostly kept out of the low noise receive channel.
(This would be bitmaps: tx 1 rx 2).
2) Another similar setup is: Use RX diversity on both antennas, but always send
on antenna 1. Again that would allow us to benefit from a higher gain RX
antenna, while staying within the legal limits.
(This would be: tx 0 rx 3).
3) And finally there can be special experimental setups in research and
development even with pre 802.11n hardware where more than 2 antennas are
available. It's good to keep the API simple, yet flexible.
Signed-off-by: Bruno Randolf <br1@einfach.org>
--
v7: Made bitmasks 32 bit wide and rebased to latest wireless-testing.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IS_ERR and PTR_ERR were called with the wrong pointer, leading to a
crash when cfg80211_get_dev_from_ifindex fails.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using these, user space can calculate a relative channel utilization
with arbitrary intervals by regularly taking snapshots of the survey
results.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need for the WDS peer address
to not be const, so make it const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Jordan's patch to allow setting the WDS
peer crossed with my patch removing all the
boilerplate code in nl80211, and consequently
he didn't make use of it yet. Fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This information is already available in mac80211, we just need to export it
via cfg80211 and nl80211.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yikes! The error return keeps a netdev reference
and the rdev mutex locked, fix that!
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds API to allow adding per-station GTKs,
updates mac80211 to support it, and also allows
drivers to remove a key from hwaccel again when
this may be necessary due to multiple GTKs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Consolidate boilerplate code needed for .dumpit
calls operating on netdevs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a new flag that requires the netdev to be
UP and use it to check instead of coding the
check into all functions that require it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes nl80211 use the new genetlink
pre_doit/post_doit hooks for locking and
checking the interface/wiphy index.
This significantly reduces the code size
and the likelihood of locking errors.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added a nl interface to set the peer bssid of a WDS interface.
Signed-off-by: Bill Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add missing unlocking of the wiphy in set_channel,
and don't try to unlock a non-existing wiphy in
set_cqm.
Cc: stable@kernel.org [2.6.35+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable management frame transmission and subscribing
to management frames through nl80211 in both cfg80211
and mac80211. Also update a few places that I forgot
to update for P2P-client mode previously, and fix a
small bug with non-action frames in this API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some user space applications only want to display survey data for
the operating channel, however there is no API to get that yet.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IBSS started from wireless extensions is currently
missing basic rate configuration, fix this by moving
the code to generate the default to the common code
that gets invoked for both nl80211 and wext.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If interface does not existk, when nl80211_set_power_save is called, (eg.
module has been unloaded) it has been causing kernel panic. Added new
goto target to avoid crash if get_rdev_dev_by_info_ifindex does not
return dev and rdev pointers.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds P2P-STA and P2P-GO as device types so
we can distinguish between those and normal STA
or AP (respectively) type interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a path in nl80211_set_wiphy where result is tested but
uninitialized.
I am hitting this path when I attempt:
sh# iw dev wlan0 set channel 10
command failed: Unknown error 1069727332 (-1069727332)
Signed-off-by: William Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some vendor specified mechanisms for 802.1X-style
functionality use a different protocol than EAP
(even if EAP is vendor-extensible). Allow setting
the ethertype for the protocol when a driver has
support for this. The default if unspecified is
EAP, of course.
Note: This is suitable only for station mode, not
for AP implementation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 95a6ccbb46c70cff376684c752831c014c87029d
Author: Johannes Berg <johannes.berg@intel.com>
Date: Thu Aug 12 15:38:38 2010 +0200
cfg80211/mac80211: extensible frame processing
introduced a netlink bug that caused parsing errors
in userspace because it forgot to close a nesting,
which would advertise a nesting length of zero to
userspace, which then completely threw off parsing
and led to
Illegal nla->nla_type == 0
being printed by libnl.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to register for more than just
action frames by giving the frame subtype, and
make it possible to use this in various modes
as well.
With some tweaks and some added functionality
this will, in the future, also be usable in AP
mode and be able to replace the cooked monitor
interface currently used in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When shared key auth is requested, cfg80211
should verify that the device is capable of
WEP crypto which is required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of errors during message composing msg should be freed after canceling.
Signed-off-by: Yuri Kululin <ext-yuri.kululin@nokia.com>
Signed-off-by: Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanse found that nl80211_set_wiphy imporperly handles a lock and netdev
reference and contains unreachable code. It is because there return statement
isntead of assignment to result variable. Fix that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jouni Malinen <j@w1.fi>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds transmit power setting type and transmit power level attributes
to NL80211_CMD_SET_WIPHY in order to facilitate adjusting of the transmit power
level of the device.
The added attributes allow selection of automatic, limited or fixed transmit
power level, with the level definable in signed mBm format.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf
Javier Cardona
Jouni Malinen
Johannes Berg
Helmut Schaa
Felix Fietkau
John W. Linville
Bill Jordan
Teemu Paasikivi
Bill Jordan
Yuri Ershov
Jiri Slaby
David S. Miller
Juuso Oikarinen