A0 hybrid steering is a form of high performance flow steering.
By using this mode, mlx4 cards use a fast limited table based steering,
in order to enable fast steering of unicast packets to a QP.
In order to implement A0 hybrid steering we allocate resources
from different zones:
(1) General range
(2) Special MAC-assigned QPs [RSS, Raw-Ethernet] each has its own region.
When we create a rss QP or a raw ethernet (A0 steerable and BF ready) QP,
we try hard to allocate the QP from range (2). Otherwise, we try hard not
to allocate from this range. However, when the system is pushed to its
limits and one needs every resource, the allocator uses every region it can.
Meaning, when we run out of raw-eth qps, the allocator allocates from the
general range (and the special-A0 area is no longer active). If we run out
of RSS qps, the mechanism tries to allocate from the raw-eth QP zone. If that
is also exhausted, the allocator will allocate from the general range
(and the A0 region is no longer active).
Note that if a raw-eth qp is allocated from the general range, it attempts
to allocate the range such that bits 6 and 7 (blueflame bits) in the
QP number are not set.
When the feature is used in SRIOV, the VF has to notify the PF what
kind of QP attributes it needs. In order to do that, along with the
"Eth QP blueflame" bit, we reserve a new "A0 steerable QP". According
to the combination of these bits, the PF tries to allocate a suitable QP.
In order to maintain backward compatibility (with older PFs), the PF
notifies which QP attributes it supports via QUERY_FUNC_CAP command.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The zone allocator is a mechanism which manages a few mlx4_bitmaps.
When allocating a resource, the user indicates the desired zone of
which this resource will be allocated from. If possible, the resource
will be allocated from this zone. Otherwise, the resource will be
allocated from a less-than, equal-to, higher-than priority zone,
according to the desired zone's properties with that respective
allocation order.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of reserved QPs is affected both from the firmware and
from the driver's requirements. This patch adds a check that
validates that this number is indeed feasable.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using BF (Blue-Flame), the QPN overrides the VLAN, CV, and SV fields
in the WQE. Thus, BF may only be used for QPNs with bits 6,7 unset.
The current Ethernet driver code reserves a Tx QP range with 256b alignment.
This is wrong because if there are more than 64 Tx QPs in use,
QPNs >= base + 65 will have bits 6/7 set.
This problem is not specific for the Ethernet driver, any entity that
tries to reserve more than 64 BF-enabled QPs should fail. Also, using
ranges is not necessary here and is wasteful.
The new mechanism introduced here will support reservation for
"Eth QPs eligible for BF" for all drivers: bare-metal, multi-PF, and VFs
(when hypervisors support WC in VMs). The flow we use is:
1. In mlx4_en, allocate Tx QPs one by one instead of a range allocation,
and request "BF enabled QPs" if BF is supported for the function
2. In the ALLOC_RES FW command, change param1 to:
a. param1[23:0] - number of QPs
b. param1[31-24] - flags controlling QPs reservation
Bit 31 refers to Eth blueflame supported QPs. Those QPs must have
bits 6 and 7 unset in order to be used in Ethernet.
Bits 24-30 of the flags are currently reserved.
When a function tries to allocate a QP, it states the required attributes
for this QP. Those attributes are considered "best-effort". If an attribute,
such as Ethernet BF enabled QP, is a must-have attribute, the function has
to check that attribute is supported before trying to do the allocation.
In a lower layer of the code, mlx4_qp_reserve_range masks out the bits
which are unsupported. If SRIOV is used, the PF validates those attributes
and masks out unsupported attributes as well. In order to notify VFs which
attributes are supported, the VF uses QUERY_FUNC_CAP command. This command's
mailbox is filled by the PF, which notifies which QP allocation attributes
it supports.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, we've fired all our completion callbacks straight from our ISR.
Some of those callbacks were lightweight (for example, mlx4_en's and
IPoIB napi callbacks), but some of them did more work (for example,
the user-space RDMA stack uverbs' completion handler). Besides that,
doing more than the minimal work in ISR is generally considered wrong,
it could even lead to a hard lockup of the system. Since when a lot
of completion events are generated by the hardware, the loop over those
events could be so long, that we'll get into a hard lockup by the system
watchdog.
In order to avoid that, add a new way of invoking completion events
callbacks. In the interrupt itself, we add the CQs which receive completion
event to a per-EQ list and schedule a tasklet. In the tasklet context
we loop over all the CQs in the list and invoke the user callback.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VFs (guests in this context) issue the QUERY_DEV_CAP command, they
need not be told that host side virtualization features such as VST, FSM
(MAC anti-spoofing) and running > 80 VFs are supported by the device.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was dropped by mistake for the napi_gro_frags flow, fix that.
Fixes: dd65beac48 ('net/mlx4_en: Extend usage of napi_gro_frags')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Simplify Device Tree initialisation; lp855x_bl
- Add Regulator support; lp855x
- Remove Bryan from the Maintainer list -- new baby, no time :)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0PNI
-----END PGP SIGNATURE-----
Merge tag 'backlight-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
- Clean-up leaky resources; pwm_bl
- Simplify Device Tree initialisation; lp855x_bl
- Add Regulator support; lp855x
- Remove Bryan from the Maintainer list -- new baby, no time :)
* tag 'backlight-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
MAINTAINERS: Remove my name from Backlight subsystem
backlight: lp855x: Add supply regulator to lp855x
backlight: lp855x: Refactor DT parsing code
backlight: pwm: Clean-up pwm requested using legacy API
The encapsulated offload flags shouldn't be unconditionally exported
to the stack. The stack expects offloading to work across all tunnel
types when those flags are set. This would break other tunnels (like
GRE) since be2net currently supports tunnel offload for VxLAN only.
Also, with VxLANs Skyhawk-R can offload only 1 UDP dport. If more
than 1 UDP port is added, we should disable offloads in that case too.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to use dma_mapping_error() to check the dma address returned
by dma_map_single/page(). Otherwise we would get warning like this:
WARNING: at lib/dma-debug.c:1140
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.18.0-rc2-next-20141029 #196
task: c0834300 ti: effe6000 task.ti: c0874000
NIP: c02b2c98 LR: c02b2c98 CTR: c030abc4
REGS: effe7d70 TRAP: 0700 Not tainted (3.18.0-rc2-next-20141029)
MSR: 00021000 <CE,ME> CR: 22044022 XER: 20000000
GPR00: c02b2c98 effe7e20 c0834300 00000098 00021000 00000000 c030b898 00000003
GPR08: 00000001 00000000 00000001 749eec9d 22044022 1001abe0 00000020 ef278678
GPR16: ef278670 ef278668 ef278660 070a8040 c087f99c c08cdc60 00029000 c0840d44
GPR24: c08be6e8 c0840000 effe7e78 ef041340 00000600 ef114e10 00000000 c08be6e0
NIP [c02b2c98] check_unmap+0x51c/0x9e4
LR [c02b2c98] check_unmap+0x51c/0x9e4
Call Trace:
[effe7e20] [c02b2c98] check_unmap+0x51c/0x9e4 (unreliable)
[effe7e70] [c02b31d8] debug_dma_unmap_page+0x78/0x8c
[effe7ed0] [c03d1640] gfar_clean_rx_ring+0x208/0x488
[effe7f40] [c03d1a9c] gfar_poll_rx_sq+0x3c/0xa8
[effe7f60] [c04f8714] net_rx_action+0xc0/0x178
[effe7f90] [c00435a0] __do_softirq+0x100/0x1fc
[effe7fe0] [c0043958] irq_exit+0xa4/0xc8
[effe7ff0] [c000d14c] call_do_irq+0x24/0x3c
[c0875e90] [c00048a0] do_IRQ+0x8c/0xf8
[c0875eb0] [c000ed10] ret_from_except+0x0/0x18
For TX, we need to unmap the pages which has already been mapped and
free the skb before return.
For RX, move the dma mapping and error check to gfar_new_skb(). We
would reuse the original skb in the rx ring when either allocating
skb failure or dma mapping error.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove use of calls into t4_fw_hello() with MASTER_MUST, which results in
FW_HELLO_CMD_MASTERFORCE being set. The firmware doesn't support this and of
course any existing PF Drivers will totally go for a toss.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Force conversion of the ux500 pin control device trees
and parsers to use the generic pin control bindings.
- New driver and device tree bindings for the Qualcomm
PMIC MPP pin controller and GPIO.
- Some ACPI infrastructure for pin controllers.
- New driver for the Intel CherryView/Braswell pin controller,
the first Intel pin controller to fully take advantage of
the pin control subsystem.
- Support the Freescale i.MX VF610 variant.
- Support the sunxi A80 variant.
- Support the Samsung Exynos 4415 and Exynos 7 variants.
- Split out Intel pin controllers to their own subdirectory.
- A large slew of rockchip pin control updates, including
suspend/resume support.
- A large slew of Samsung Exynos pin controller updates.
- Various minor updates and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sxpe
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
"Here is a stash of pin control changes I have collected for the v3.19
series. Mainly new hardware support, with Intels new embedded SoC as
the especially interesting thing standing out, fully using the
subsystem.
- Force conversion of the ux500 pin control device trees and parsers
to use the generic pin control bindings.
- New driver and device tree bindings for the Qualcomm PMIC MPP pin
controller and GPIO.
- Some ACPI infrastructure for pin controllers.
- New driver for the Intel CherryView/Braswell pin controller, the
first Intel pin controller to fully take advantage of the pin
control subsystem.
- Support the Freescale i.MX VF610 variant.
- Support the sunxi A80 variant.
- Support the Samsung Exynos 4415 and Exynos 7 variants.
- Split out Intel pin controllers to their own subdirectory.
- A large slew of rockchip pin control updates, including
suspend/resume support.
- A large slew of Samsung Exynos pin controller updates.
- Various minor updates and fixes"
* tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (49 commits)
pinctrl: at91: enhance (debugfs) at91_gpio_dbg_show
pinctrl: meson: add device tree bindings documentation
gpio: tz1090: Fix error handling of irq_of_parse_and_map
pinctrl: tz1090-pinctrl.txt: Fix typo in binding
pinctrl: pinconf-generic: Declare dt_params/conf_items const
pinctrl: exynos: Add support for Exynos4415
pinctrl: exynos: Add initial driver data for Exynos7
pinctrl: exynos: Add irq_chip instance for Exynos7 wakeup interrupts
pinctrl: exynos: Consolidate irq domain callbacks
pinctrl: exynos: Generalize the eint16_31 demux code
pinctrl: samsung: Separate per-bank init and runtime data
pinctrl: samsung: Constify samsung_pin_ctrl struct
pinctrl: samsung: Constify samsung_pin_bank_type struct
pinctrl: samsung: Drop unused label field in samsung_pin_ctrl struct
pinctrl: samsung: Make samsung_pinctrl_get_soc_data use ERR_PTR()
pinctrl: Add Intel Cherryview/Braswell pin controller support
gpio / ACPI: Add knowledge about pin controllers to acpi_get_gpiod()
pinctrl: Fix path error in documentation
pinctrl: rockchip: save and restore gpio6_c6 pinmux in suspend/resume
pinctrl: rockchip: add suspend/resume functions
...
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
o Fix handling the make kernelrelease change
o Fix make_min_config that was broken by new bisect_config changes
o Allow tests to undefine default options (not just being able to override
them)
o Print name of test (if defined) to start of test output
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUheY3AAoJEEjnJuOKh9ld+CgH/16NxltuIVFMTDB+I7AP/ixV
YP2m4dGn0wrzg8GhZNJX7x9irh8Shg5da4mjqH163qylNfQl7QuALzs5c7B3ZDv3
dQa2GMR34/bUbcqejrZm7fcwRH8yw1E88hAs71CNM+PMW1AAe8CBth2ogCXC/V8N
uln7Fr0aS3Y/sPxWzkCp4Y8ZAsoRMei3igfnJUPu0a1p7pyKaN0ne060S5znWYwl
8fW4DACR1EppMmfwdslORN9miPol4nuBQICmqNM6shtJaef6yb9aErSiTTT4m4PK
RIpWZasmosKBIeIkTXWxLhr3liEFTMm3BsflD+YUnIM7cLFziHGDp6ThH3TwwSo=
=Y3vY
-----END PGP SIGNATURE-----
Merge tag 'ktest-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull ktest changes from Steven Rostedt:
"The following ktest updates were done:
- Fix handling the make kernelrelease change
- Fix make_min_config that was broken by new bisect_config changes
- Allow tests to undefine default options (not just being able to
override them)
- Print name of test (if defined) to start of test output"
* tag 'ktest-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Add back "tail -1" to kernelrelease make
ktest: Add name to running title
ktest: Allow tests to undefine default options
ktest: Fix make_min_config to handle new assign_configs call
ktest: Use make -s kernelrelease
Fugang Duan says:
====================
net: fec: driver code clean and bug fix
The patch serial include code clean and bug fix:
Patch#1: avoid dummy operation during suspend/resume test.
Patch#2: bug fix for i.MX6SX SOC that clean all interrupt events during MAC initial process.
Patch#3: before phy device link status is up, only enable MDIO bus interrupt.
V2:
- Modify the comment form from David's suggestion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Before phy device link up, we only enable FEC mdio interrupt, which
is more reasonable.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For i.MX6SX FEC controller, there have interrupt mask and event
field extension. To support all SOCs FEC, we clear all interrupt
events during MAVC initial process.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some i.MX6 serial boards, phy power and refrence clock are supplied
or controlled by SOC. When do suspend/resume test, the power and clock
are disabled, so phy device link down.
For current driver, fep->link is still up status, which cause extra operation
like below code. To avoid the dumy operation, we set fep->link to down when
phy device is real down.
...
if (fep->link) {
napi_disable(&fep->napi);
netif_tx_lock_bh(ndev);
fec_stop(ndev);
netif_tx_unlock_bh(ndev);
napi_enable(&fep->napi);
fep->link = phy_dev->link;
status_change = 1;
}
...
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clean ups from that branch.
This code solves the issue of performing stack dumps from NMI context.
The issue is that printk() is not safe from NMI context as if the NMI
were to trigger when a printk() was being performed, the NMI could
deadlock from the printk() internal locks. This has been seen in practice.
With lots of review from Petr Mladek, this code went through several
iterations, and we feel that it is now at a point of quality to be
accepted into mainline.
Here's what is contained in this patch set:
o Creates a "seq_buf" generic buffer utility that allows a descriptor
to be passed around where functions can write their own "printk()"
formatted strings into it. The generic version was pulled out of
the trace_seq() code that was made specifically for tracing.
o The seq_buf code was change to model the seq_file code. I have
a patch (not included for 3.19) that converts the seq_file.c code
over to use seq_buf.c like the trace_seq.c code does. This was done
to make sure that seq_buf.c is compatible with seq_file.c. I may
try to get that patch in for 3.20.
o The seq_buf.c file was moved to lib/ to remove it from being dependent
on CONFIG_TRACING.
o The printk() was updated to allow for a per_cpu "override" of
the internal calls. That is, instead of writing to the console, a call
to printk() may do something else. This made it easier to allow the
NMI to change what printk() does in order to call dump_stack() without
needing to update that code as well.
o Finally, the dump_stack from all CPUs via NMI code was converted to
use the seq_buf code. The caller to trigger the NMI code would wait
till all the NMIs finished, and then it would print the seq_buf
data to the console safely from a non NMI context.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUhbrnAAoJEEjnJuOKh9ldsCoIAJ3sKIJ5B3jxJJTCHPAx/lZD
GVbV1J1mu4kTAZuhJZOAxW8D6PZGZMyEjg0y6ScDEnBGcjAZ9gTiWCdakPktf9EX
GfaPPqwiL9dZ18J9Qc6uR+7M1Ffpzzwbcc6lJrpoTcjRgkoH9wCiLS9ozFQyYzWb
/7m5UbUM/PIk9WAjLYXPW6UUVtPTPT0RdEQKofMGTeah+vgqj4TXCOROdlxsXXWF
77vqBvPd5TUPWFH9ftzJGDtZS8SroXVKCu3fZIqHgzAU0yqwVtH/JzDTy9u2UYhX
GzDEPeAIdp6m6Uyc406VuIf1QW0gfBgmA0ir80vFoP27uFMM6j5HlF7azgQfx34=
=YBgA
-----END PGP SIGNATURE-----
Merge tag 'trace-seq-buf-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull nmi-safe seq_buf printk update from Steven Rostedt:
"This code is a fork from the trace-3.19 pull as it needed the
trace_seq clean ups from that branch.
This code solves the issue of performing stack dumps from NMI context.
The issue is that printk() is not safe from NMI context as if the NMI
were to trigger when a printk() was being performed, the NMI could
deadlock from the printk() internal locks. This has been seen in
practice.
With lots of review from Petr Mladek, this code went through several
iterations, and we feel that it is now at a point of quality to be
accepted into mainline.
Here's what is contained in this patch set:
- Creates a "seq_buf" generic buffer utility that allows a descriptor
to be passed around where functions can write their own "printk()"
formatted strings into it. The generic version was pulled out of
the trace_seq() code that was made specifically for tracing.
- The seq_buf code was change to model the seq_file code. I have a
patch (not included for 3.19) that converts the seq_file.c code
over to use seq_buf.c like the trace_seq.c code does. This was
done to make sure that seq_buf.c is compatible with seq_file.c. I
may try to get that patch in for 3.20.
- The seq_buf.c file was moved to lib/ to remove it from being
dependent on CONFIG_TRACING.
- The printk() was updated to allow for a per_cpu "override" of the
internal calls. That is, instead of writing to the console, a call
to printk() may do something else. This made it easier to allow
the NMI to change what printk() does in order to call dump_stack()
without needing to update that code as well.
- Finally, the dump_stack from all CPUs via NMI code was converted to
use the seq_buf code. The caller to trigger the NMI code would
wait till all the NMIs finished, and then it would print the
seq_buf data to the console safely from a non NMI context
One added bonus is that this code also makes the NMI dump stack work
on PREEMPT_RT kernels. As printk() includes sleeping locks on
PREEMPT_RT, printk() only writes to console if the console does not
use any rt_mutex converted spin locks. Which a lot do"
* tag 'trace-seq-buf-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
x86/nmi: Fix use of unallocated cpumask_var_t
printk/percpu: Define printk_func when printk is not defined
x86/nmi: Perform a safe NMI stack trace on all CPUs
printk: Add per_cpu printk func to allow printk to be diverted
seq_buf: Move the seq_buf code to lib/
seq-buf: Make seq_buf_bprintf() conditional on CONFIG_BINARY_PRINTF
tracing: Add seq_buf_get_buf() and seq_buf_commit() helper functions
tracing: Have seq_buf use full buffer
seq_buf: Add seq_buf_can_fit() helper function
tracing: Add paranoid size check in trace_printk_seq()
tracing: Use trace_seq_used() and seq_buf_used() instead of len
tracing: Clean up tracing_fill_pipe_page()
seq_buf: Create seq_buf_used() to find out how much was written
tracing: Add a seq_buf_clear() helper and clear len and readpos in init
tracing: Convert seq_buf fields to be like seq_file fields
tracing: Convert seq_buf_path() to be like seq_path()
tracing: Create seq_buf layer in trace_seq
0day robot reported the following crash:
[ 21.233581] BUG: unable to handle kernel NULL pointer dereference at 0000000000000007
[ 21.234709] IP: [<ffffffff8156ebda>] sk_attach_bpf+0x39/0xc2
It's due to bpf_prog_get() returning ERR_PTR.
Check it properly.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes: 89aa075832 ("net: sock: allow eBPF programs to be attached to sockets")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Added kprobes on ftrace testcase
o Sort test cases
o Add file to hold helper functions
o Use logfile name supported by busybox's mktemp
o Clear trace buffer after running kprobe test
o Fix show descriptions when run on dash shell
o Add --verbose option for showing echo output
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUhbSvAAoJEEjnJuOKh9ldB84H+gNuE2PPvsxmgSxFP0bdo+Uw
k/8C2QBU6xLXZFZvqXnH7P0gLP2OIjpOBOTKt+yjkB/Elm+XnMVV1Xy+k7VLBiMD
g+DRoIcpJL2dOy/D8t/P4SjVNXt4Btwxf/tCTabbubLc+aBmvkEG4DL2Vk/Xl5+Y
XH1dBgYvI9irAxgnYpBnPlN7WIWg1+WCshdOtqkNGRuyJ1G9gn0VlxGmNF7B+0ye
cjFj19loPMGzmYBDgGCa9ypQHEP1F97t+WUEDrwCZsXLtaA7Z4bumXTrxKQWsmdT
bDZQTEFcQ9EYQGvqbaz+nHb94P8cyFrSNvSiAAqhuc2ZqigYWUYDEvFjYxSSGAE=
=eiD2
-----END PGP SIGNATURE-----
Merge tag 'ftracetest-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace self-test updates from Steven Rostedt:
"Updates for the ftrace self tests:
- Added kprobes on ftrace testcase
- Sort test cases
- Add file to hold helper functions
- Use logfile name supported by busybox's mktemp
- Clear trace buffer after running kprobe test
- Fix show descriptions when run on dash shell
- Add --verbose option for showing echo output"
* tag 'ftracetest-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftracetest: Add --verbose option for showing echo output
ftracetest: Fix to show descriptions on dash
ftracetest: Add basic event tracing test cases
ftracetest: Clear trace buffer after running kprobe testcases
ftracetest: Use logfile name supported by busybox's mktemp
ftracetest: Add a couple of ftrace test cases
ftracetest: Add functions file that holds helper functions
ftracetest: Sort testcases
ftracetest: Add kprobes on ftrace testcase
to the trace_seq code. It also removed the return values to the
trace_seq_*() functions and use trace_seq_has_overflowed() to see if
the buffer filled up or not. This is similar to work being done to the
seq_file code as well in another tree.
Some of the other goodies include:
o Added some "!" (NOT) logic to the tracing filter.
o Fixed the frame pointer logic to the x86_64 mcount trampolines
o Added the logic for dynamic trampolines on !CONFIG_PREEMPT systems.
That is, the ftrace trampoline can be dynamically allocated
and be called directly by functions that only have a single hook
to them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUhbLGAAoJEEjnJuOKh9ldRV4H/3NcLbgGB2iu96la1zdYE6pG
Q7cDJMxXK80YIIL70h9G0IItcD4t62LMb72lfBnMGRj3msgFb3AgISW57EuI0Pxk
xk24wuIPoTG2S7v9sc3SboNFwO8qbtIjxD2OBmqIUrGo2sZIiGjyj3gX7mCY3uzL
WB2bUOSFz/22OgaANinR5EELHA3pZZCf54Vz1K9ndmtK0xp0j1a7xJShD6TrMdYv
mZ3zH5ViIhW4A3mdcMceh6fy2JLQAiEKF0uPTvcMMz7NlVul0mxyL/+10P7AE/3R
Ehw4fzmm4NDshPDtBOkKH0LsppgXzuItFuQUTpact3JlqTg++bV6onSsrkt1hlY=
=Z7Cm
-----END PGP SIGNATURE-----
Merge tag 'trace-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"There was a lot of clean ups and minor fixes. One of those clean ups
was to the trace_seq code. It also removed the return values to the
trace_seq_*() functions and use trace_seq_has_overflowed() to see if
the buffer filled up or not. This is similar to work being done to
the seq_file code as well in another tree.
Some of the other goodies include:
- Added some "!" (NOT) logic to the tracing filter.
- Fixed the frame pointer logic to the x86_64 mcount trampolines
- Added the logic for dynamic trampolines on !CONFIG_PREEMPT systems.
That is, the ftrace trampoline can be dynamically allocated and be
called directly by functions that only have a single hook to them"
* tag 'trace-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (55 commits)
tracing: Truncated output is better than nothing
tracing: Add additional marks to signal very large time deltas
Documentation: describe trace_buf_size parameter more accurately
tracing: Allow NOT to filter AND and OR clauses
tracing: Add NOT to filtering logic
ftrace/fgraph/x86: Have prepare_ftrace_return() take ip as first parameter
ftrace/x86: Get rid of ftrace_caller_setup
ftrace/x86: Have save_mcount_regs macro also save stack frames if needed
ftrace/x86: Add macro MCOUNT_REG_SIZE for amount of stack used to save mcount regs
ftrace/x86: Simplify save_mcount_regs on getting RIP
ftrace/x86: Have save_mcount_regs store RIP in %rdi for first parameter
ftrace/x86: Rename MCOUNT_SAVE_FRAME and add more detailed comments
ftrace/x86: Move MCOUNT_SAVE_FRAME out of header file
ftrace/x86: Have static tracing also use ftrace_caller_setup
ftrace/x86: Have static function tracing always test for function graph
kprobes: Add IPMODIFY flag to kprobe_ftrace_ops
ftrace, kprobes: Support IPMODIFY flag to find IP modify conflict
kprobes/ftrace: Recover original IP if pre_handler doesn't change it
tracing/trivial: Fix typos and make an int into a bool
tracing: Deletion of an unnecessary check before iput()
...
Introduce helper macro for_each_cmsghdr as a wrapper of the enumerating
cmsghdr from msghdr, just cleanup.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge first patchbomb from Andrew Morton:
- a few minor cifs fixes
- dma-debug upadtes
- ocfs2
- slab
- about half of MM
- procfs
- kernel/exit.c
- panic.c tweaks
- printk upates
- lib/ updates
- checkpatch updates
- fs/binfmt updates
- the drivers/rtc tree
- nilfs
- kmod fixes
- more kernel/exit.c
- various other misc tweaks and fixes
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (190 commits)
exit: pidns: fix/update the comments in zap_pid_ns_processes()
exit: pidns: alloc_pid() leaks pid_namespace if child_reaper is exiting
exit: exit_notify: re-use "dead" list to autoreap current
exit: reparent: call forget_original_parent() under tasklist_lock
exit: reparent: avoid find_new_reaper() if no children
exit: reparent: introduce find_alive_thread()
exit: reparent: introduce find_child_reaper()
exit: reparent: document the ->has_child_subreaper checks
exit: reparent: s/while_each_thread/for_each_thread/ in find_new_reaper()
exit: reparent: fix the cross-namespace PR_SET_CHILD_SUBREAPER reparenting
exit: reparent: fix the dead-parent PR_SET_CHILD_SUBREAPER reparenting
exit: proc: don't try to flush /proc/tgid/task/tgid
exit: release_task: fix the comment about group leader accounting
exit: wait: drop tasklist_lock before psig->c* accounting
exit: wait: don't use zombie->real_parent
exit: wait: cleanup the ptrace_reparented() checks
usermodehelper: kill the kmod_thread_locker logic
usermodehelper: don't use CLONE_VFORK for ____call_usermodehelper()
fs/hfs/catalog.c: fix comparison bug in hfs_cat_keycmp
nilfs2: fix the nilfs_iget() vs. nilfs_new_inode() races
...
The comments in zap_pid_ns_processes() are not clear, we need to explain
how this code actually works.
1. "Ignore SIGCHLD" looks like optimization but it is not, we also
need this for correctness.
2. The comment above sys_wait4() could tell more.
EXIT_ZOMBIE child is only possible if it has exited before we
ignored SIGCHLD. Or if it is traced from the parent namespace,
but in this case it will be reaped by debugger after detach,
sys_wait4() acts as a synchronization point.
3. The comment about TASK_DEAD (EXIT_DEAD in fact) children is
outdated. Contrary to what it says we do not need to make sure
they all go away after 0a01f2cc39 "pidns: Make the pidns proc
mount/umount logic obvious".
At the same time, we do need to wait for nr_hashed==init_pids,
but the reasons are quite different and not obvious: setns().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: Sterling Alexander <stalexan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alloc_pid() does get_pid_ns() beforehand but forgets to put_pid_ns() if it
fails because disable_pid_allocation() was called by the exiting
child_reaper.
We could simply move get_pid_ns() down to successful return, but this fix
tries to be as trivial as possible.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: Sterling Alexander <stalexan@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After the previous change we can add just the exiting EXIT_DEAD task to
the "dead" list and remove another release_task(tsk).
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Sterling Alexander <stalexan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shift "release dead children" loop from forget_original_parent() to its
caller, exit_notify(). It is safe to reap them even if our parent reaps
us right after we drop tasklist_lock, those children no longer have any
connection to the exiting task.
And this allows us to avoid write_lock_irq(tasklist_lock) right after it
was released by forget_original_parent(), we can simply call it with
tasklist_lock held.
While at it, move the comment about forget_original_parent() up to
this function.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Sterling Alexander <stalexan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that pid_ns logic was isolated we can change forget_original_parent()
to return right after find_child_reaper() when father->children is empty,
there is nothing to reparent in this case.
In particular this avoids find_alive_thread() and this can help if the
whole process exits and it has a lot of PF_EXITING threads at the start of
the thread list, this can easily lead to O(nr_threads ** 2) iterations.
Trivial test case (tested under KVM, 2 CPUs):
static void *tfunc(void *arg)
{
pause();
return NULL;
}
static int child(unsigned int nt)
{
pthread_t pt;
while (nt--)
assert(pthread_create(&pt, NULL, tfunc, NULL) == 0);
pthread_kill(pt, SIGTRAP);
pause();
return 0;
}
int main(int argc, const char *argv[])
{
int stat;
unsigned int nf = atoi(argv[1]);
unsigned int nt = atoi(argv[2]);
while (nf--) {
if (!fork())
return child(nt);
wait(&stat);
assert(stat == SIGTRAP);
}
return 0;
}
$ time ./test 16 16536 shows:
real user sys
- 5m37.628s 0m4.437s 8m5.560s
+ 0m50.032s 0m7.130s 1m4.927s
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Sterling Alexander <stalexan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the new simple helper to factor out the for_each_thread() code in
find_child_reaper() and find_new_reaper(). It can also simplify the
potential PF_EXITING -> exit_state change, plus perhaps we can change this
code to take SIGNAL_GROUP_EXIT into account.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Sterling Alexander <stalexan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
find_new_reaper() does 2 completely different things. Not only it finds a
reaper, it also updates pid_ns->child_reaper or kills the whole namespace
if the caller is ->child_reaper.
Now that has_child_subreaper logic doesn't depend on child_reaper check we
can move that pid_ns code into a separate helper. IMHO this makes the
code more clean, and this allows the next changes.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Sterling Alexander <stalexan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Swap the "init_task" and same_thread_group() checks. This way it is more
simple to document these checks and we can remove the link to the previous
discussion on lkml.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Sterling Alexander <stalexan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change find_new_reaper() to use for_each_thread() instead of deprecated
while_each_thread(). We do not bother to check "thread != father" in the
1st loop, we can rely on PF_EXITING check.
Note: this means the minor behavioural change: for_each_thread() starts
from the group leader. But this should be fine, nobody should make any
assumption about do_wait(__WNOTHREAD) when it comes to reparented tasks.
And this can avoid the pointless reparenting to a short-living thread
While zombie leaders are not that common.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Sterling Alexander <stalexan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
find_new_reaper() assumes that "has_child_subreaper" logic is safe as
long as we are not the exiting ->child_reaper and this is doubly wrong:
1. In fact it is safe if "pid_ns->child_reaper == father"; there must
be no children after zap_pid_ns_processes() returns, so it doesn't
matter what we return in this case and even pid_ns->child_reaper is
wrong otherwise: we can't reparent to ->child_reaper == current.
This is not a bug, but this is confusing.
2. It is not safe if we are not pid_ns->child_reaper but from the same
thread group. We drop tasklist_lock before zap_pid_ns_processes(),
so another thread can lock it and choose the new reaper from the
upper namespace if has_child_subreaper == T, and this is obviously
wrong.
This is not that bad, zap_pid_ns_processes() won't return until the
the new reaper reaps all zombies, but this should be fixed anyway.
We could change for_each_thread() loop to use ->exit_state instead of
PF_EXITING which we had to use until 8aac62706a, or we could change
copy_signal() to check CLONE_NEWPID before setting has_child_subreaper,
but lets change this code so that it is clear we can't look outside of
our namespace, otherwise same_thread_group(reaper, child_reaper) check
will look wrong and confusing anyway.
We can simply start from "father" and fix the problem. We can't wrongly
return a thread from the same thread group if ->is_child_subreaper == T,
we know that all threads have PF_EXITING set.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Sterling Alexander <stalexan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ->has_child_subreaper code in find_new_reaper() finds alive "thread"
but returns another "reaper" thread which can be dead.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Sterling Alexander <stalexan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
proc_flush_task_mnt() always tries to flush task/pid, but this is
pointless if we reap the leader. d_invalidate() is recursive, and
if nothing else the next d_hash_and_lookup(tgid) should fail anyway.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sterling Alexander <stalexan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Contrary to what the comment in __exit_signal() says we do account the
group leader. Fix this and explain why.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sterling Alexander <stalexan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
wait_task_zombie() no longer needs tasklist_lock to accumulate the
psig->c* counters, we can drop it right after cmpxchg(exit_state).
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sterling Alexander <stalexan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. wait_task_zombie() uses p->real_parent to get psig/siglock. This is
correct but needs tasklist_lock, ->real_parent can exit.
We can use "current" instead. This is our natural child, its parent
must be our sub-thread.
2. Read psig/sig outside of ->siglock, ->signal is no longer protected
by this lock.
3. Fix the outdated comments about tasklist_lock. We can not race with
__exit_signal(), the whole thread group is dead, nobody but us can
call it.
Also clarify the usage of ->stats_lock and ->siglock.
Note: thread_group_cputime_adjusted() is sub-optimal in this case, we
probably want to export cputime_adjust() to avoid thread_group_cputime().
The comment says "all threads" but there are no other threads.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sterling Alexander <stalexan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that EXIT_DEAD is the terminal state we can kill "int traced"
variable and check "state == EXIT_DEAD" instead to cleanup the code. In
particular, this way it is clear that the check obviously doesn't need
tasklist_lock.
Also fix the type of "unsigned long state", "long" was always wrong
although this doesn't matter because cmpxchg/xchg uses typeof(*ptr).
[akpm@linux-foundation.org: don't make me google the C Operator Precedence table]
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sterling Alexander <stalexan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we do not call kernel_thread(CLONE_VFORK) from the worker
thread we can not deadlock if do_execve() in turn triggers another
call_usermodehelper(), we can remove the kmod_thread_locker code.
Note: we should probably kill khelper_wq and simply use one of the
global workqueues, say, system_unbound_wq, this special wq for umh buys
nothing nowadays.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After "kernel/kmod: fix use-after-free of the sub_infostructure"
CLONE_VFORK in __call_usermodehelper() buys nothing, we rely on on
umh_complete() in ____call_usermodehelper() anyway.
Remove it. This also eliminates the unnecessary sleep/wakeup in the
likely case, and this allows the next change.
While at it, kill the "int wait" locals in ____call_usermodehelper() and
__call_usermodehelper(), they can safely use sub_info->wait.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Relying on the sign (after casting to int) of the difference of two
quantities for comparison is usually wrong. For example, should a-b
turn out to be 2^31, the return value of cmp(a,b) is -2^31; but that
would also be the return value from cmp(b, a). So a compares less than
b and b compares less than a. One can also easily find three values
a,b,c such that a compares less than b, b compares less than c, but a
does not compare less than c.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Same story as in commit 41080b5a24 ("nfsd race fixes: ext2") (similar
ext2 fix) except that nilfs2 needs to use insert_inode_locked4() instead
of insert_inode_locked() and a bug of a check for dead inodes needs to
be fixed.
If nilfs_iget() is called from nfsd after nilfs_new_inode() calls
insert_inode_locked4(), nilfs_iget() will wait for unlock_new_inode() at
the end of nilfs_mkdir()/nilfs_create()/etc to unlock the inode.
If nilfs_iget() is called before nilfs_new_inode() calls
insert_inode_locked4(), it will create an in-core inode and read its
data from the on-disk inode. But, nilfs_iget() will find i_nlink equals
zero and fail at nilfs_read_inode_common(), which will lead it to call
iget_failed() and cleanly fail.
However, this sanity check doesn't work as expected for reused on-disk
inodes because they leave a non-zero value in i_mode field and it
hinders the test of i_nlink. This patch also fixes the issue by
removing the test on i_mode that nilfs2 doesn't need.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The iput() function tests whether its argument is NULL and then returns
immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes filemap_write_and_wait_range() from nilfs_sync_file(),
because it triggers a data segment construction by calling
nilfs_writepages() with WB_SYNC_ALL. A data segment construction does not
remove the inode from the i_dirty list and it does not clear the
NILFS_I_DIRTY flag. Therefore nilfs_inode_dirty() still returns true,
which leads to an unnecessary duplicate segment construction in
nilfs_sync_file().
A call to filemap_write_and_wait_range() is not needed, because NILFS2
does not rely on the generic writeback mechanisms. Instead it implements
its own mechanism to collect all dirty pages and write them into segments.
It is more efficient to initiate the segment construction directly in
nilfs_sync_file() without the detour over filemap_write_and_wait_range().
Additionally the lock of i_mutex is not needed, because all code blocks
that are protected by i_mutex are also protected by a NILFS transaction:
Function i_mutex nilfs_transaction
------------------------------------------------------
nilfs_ioctl_setflags: yes yes
nilfs_fiemap: yes no
nilfs_write_begin: yes yes
nilfs_write_end: yes yes
nilfs_lookup: yes no
nilfs_create: yes yes
nilfs_link: yes yes
nilfs_mknod: yes yes
nilfs_symlink: yes yes
nilfs_mkdir: yes yes
nilfs_unlink: yes yes
nilfs_rmdir: yes yes
nilfs_rename: yes yes
nilfs_setattr: yes yes
For nilfs_lookup() i_mutex is held for the parent directory, to protect it
from modification. The segment construction does not modify directory
inodes, so no lock is needed.
nilfs_fiemap() reads the block layout on the disk, by using
nilfs_bmap_lookup_contig(). This is already protected by bmap->b_sem.
Signed-off-by: Andreas Rohner <andreas.rohner@gmx.net>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc_timer_do_work() only judges -ETIME failure of__rtc_set_alarm(), but
doesn't handle other failures like -EIO, -EBUSY, etc.
If there is a failure other than -ETIME, the next rtc_timer will stay in
the timerqueue. Then later rtc_timers will be enqueued directly because
they have a later expires time, so the alarm irq will never be programmed.
When such failures happen, this patch will retry __rtc_set_alarm(), if
still can't program the alarm time, it will remove current rtc_timer from
timerqueue and fetch next one, thus preventing it from affecting other rtc
timers.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, ab8500 doesn't set uie_unsupported of rtc_device, while it
doesn't support UIE, see ab8500_rtc_set_alarm().
Thus, when going through rtc_update_irq_enable()->rtc_timer_enqueue(),
there's a chance it has an alarm timer1 queued before which is going to
fired, so this update timer2 will be queued because it isn't the leftmost
one, which means rtc_timer_enqueue() will return 0.
This will result in two problems:
1) UIE EMUL will not be used.
2) When the alarm timer1 is fired, in rtc_timer_do_work() timer2 will
fail to set the alarm time, so this rtc will disfunctional due to
timer2 with the earliest expires in the timerqueue.
So, rtc drivers must set this flag if they don't support UIE.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The alarm interrupt handler also reads registers which are part of SNVS
and need clocks enabled. However, the resume function is called after
IRQ's have been enabled, hence this leads to a abort:
Unhandled fault: external abort on non-linefetch (0x1008) at 0x908c604c
Internal error: : 1008 [#1] ARM
Modules linked in:
CPU: 0 PID: 421 Comm: sh Not tainted 3.18.0-rc5-00135-g0689c67-dirty #1592
task: 8e03e800 ti: 8cad8000 task.ti: 8cad8000
PC is at snvs_rtc_irq_handler+0x14/0x74
LR is at handle_irq_event_percpu+0x3c/0x144
Fix this by using the .{suspend/resume}_noirq callbacks instead of
.{suspend/resume} .
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matan Barak
Dotan Barak
Eugenia Emantayev
Or Gerlitz
Linus Torvalds
Sriharsha Basavapatna
Kevin Hao
Hariprasad Shenai
David S. Miller
Nimrod Andy
Alexei Starovoitov
Gu Zheng
Oleg Nesterov
Rasmus Villemoes
Ryusuke Konishi
Markus Elfring
Andreas Rohner
Xunlei Pang
Sanchayan Maity