Commit Graph

524 Commits

Author SHA1 Message Date
Linus Torvalds 21ebd6c68b Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
  rtc: max8925: Add function to work as wakeup source
  mfd: Add pm ops to max8925
  mfd: Convert aat2870 to dev_pm_ops
  mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
  mfd: Introduce missing kfree in 88pm860x probe routine
  mfd: Add S5M series configuration
  mfd: Add s5m series irq driver
  mfd: Add S5M core driver
  mfd: Improve mc13xxx dt binding document
  mfd: Fix stmpe section mismatch
  mfd: Fix stmpe build warning
  mfd: Fix STMPE I2c build failure
  mfd: Constify aat2870-core i2c_device_id table
  gpio: Add support for stmpe variant 801
  mfd: Add support for stmpe variant 801
  mfd: Add support for stmpe variant 610
  mfd: Add support for STMPE SPI interface
  mfd: Separate out STMPE controller and interface specific code
  misc: Remove max8997-muic sysfs attributes
  mfd: Remove unused wm831x_irq_data_to_mask_reg()
  ...

Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
2012-01-13 20:43:32 -08:00
Linus Walleij ee66e653ca mfd: Unify abx500 headers in mfd/abx500
This moves all the header files related to the abx500 family into
a common include directory below mfd. From now on we place any
subchip header in that directory. Headers previously in e.g.
<linux/mfd/ab8500/gpio.h> get prefixed and are now e.g.
<linux/mfd/abx500/ab8500-gpio.h>. The top-level abstract interface
remains in <linux/mfd/abx500.h>.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-01-09 00:37:39 +01:00
Richard Zhao 0c437c4ae7 regulator: set constraints.apply_uV to 0 in of_get_fixed_voltage_config
Fix fixed regulator using DT failed to call regulator_register.

of_get_regulator_init_data set apply_uV to 1, but fixed regulator
doesn't need it. Set it back to 0.

Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-01-06 11:01:09 -08:00
Kevin Liu 65364e9ab9 regulator: max8925: fix enabled/disabled judgement mistake
Max8925 ldo status should be determined by two factors:
1. power up/down sequence selection(LDOCTL[4:2]).
2. i2c enable bit(LDOCTL[0]).

Max8925 ldo support two types of power up/down sequence:
1. flexible sequence(LDOCTL[4:2] = 0~6).
2. i2c sequence(LDOCTL[4:2] = 7).

With flexible sequence selected, the ldo is enabled during power up by default.
With i2c sequence selected, the ldo is controlled by the i2c enable bit(LDOCTL[0]).

Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-01-06 10:56:14 -08:00
Donggeun Kim e1de2f4234 regulator: add regulator_bulk_force_disable function
This patch allows consumers to forcibly disable multiple regulator
clients in a single API call.

Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-01-03 20:20:01 +00:00
Richard Zhao 1bb50b28a9 regulator: pass regulator_register of_node in fixed voltage driver
regulator_get needs of_node to find right regulator.

Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-01-02 12:45:37 +00:00
Laxman Dewangan b2296bd43e regulator: Enable supply regulator if child rail is enabled.
During regulator_register, the rail is set on the provided
machine constraints and if it is enabled then it is also
require to enable the supply regulator. This will make sure
that:
   1. Proper reference count for supply regulator to be maintain.
   2. Supply regulator should be enable when given rail is enabled.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-01-02 11:36:02 +00:00
Fabio Estevam 4fef21eaac regulator: mc13892: Convert to devm_kzalloc()
Convert mc13892-regulator driver to use devm_kzalloc().

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-30 02:06:29 +00:00
Fabio Estevam cbe10a3674 regulator: mc13783: Convert to devm_kzalloc()
Convert mc13783-regulator driver to use devm_kzalloc().

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-29 17:58:37 +00:00
Axel Lin 32c78de8f1 regulator: Fix checking return value of create_regulator
create_regulator() returns NULL on fail.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-29 10:40:19 +00:00
Axel Lin bcda432194 regulator: Fix the error handling if create_regulator fails
In the case of create_regulator() fails, goto the error path immediately.
It does not make sense to update rdev->open_count if create_regulator fails.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-29 10:40:19 +00:00
Mark Brown a398eaa23e regulator: Export regulator_is_supported_voltage()
It's part of the driver interface so should be available to modules.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-28 17:09:32 +00:00
Shawn Guo 93bcb23b38 regulator: mc13892: add device tree probe support
It adds device tree probe support for mc13892-regulator driver.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-22 11:10:45 +00:00
Shawn Guo 3a5d03158d regulator: mc13892: remove the unnecessary prefix from regulator name
It's not really necessary to add a prefix 'MC13892__' for each mc13892
regulator name, since the chip must have been identified as mc13892
when we look at the regulator name.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-22 11:07:21 +00:00
Mark Brown fded2f4fae regulator: Convert wm831x regulator drivers to devm_kzalloc()
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-20 11:29:05 +00:00
Axel Lin 6242eae9bc regulator: da9052: Staticize non-exported symbols
da9052_regulator_info and da9053_regulator_info are not used outside
this driver so no need to make the symbol global.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-20 10:02:48 +00:00
Ashish Jangam 984b5a6ba5 regulator: Replace kzalloc with devm_kzalloc and if-else with a switch-case for da9052-regulator
Reported-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-17 09:25:47 +00:00
Mark Brown 47aed92c77 regulator: Update da9052-regulator for DT changes
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-15 15:03:38 +08:00
Ashish Jangam 08bf1c0ae9 regulator: DA9052/53 Regulator support
The Dialog PMIC has below featured regulators:-
DA9052-BC - 4 DVS Buck converters 0.5V - 3.6V upto 1Amp.
DA9053-AA/BX - 4 DVS Buck converters 0.5V - 2.5V upto 3Amp.
DA9052/53 - 10 Programmable LDO's High PSSR, 1% accuracy.

This patch support all the DA9052 and Da9053 regulators. The output voltages are
fully programmable via I2C or SPI interface. The platform data with regulation
constraints is passed down from the board to the regulator.

Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-15 02:00:10 +08:00
Mark Brown 2f288efd2f Merge branch 'topic/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-next 2011-12-05 19:27:49 +00:00
Shawn Guo d9a861cce1 regulator: pass device_node to of_get_regulator_init_data()
It's not always true that the device_node of regulator can be found
at dev->of_node at the time when of_get_regulator_init_data() is being
called, because in some cases the regulator nodes in device tree do
not have 'struct device' behind them until regulator_dev gets created
for it by core function regulator_register().

The patch adds device_node as a new parameter to
of_get_regulator_init_data(), so that caller can pass in the node of
regulator directly.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-05 19:10:17 +00:00
Mark Brown ab62aa931e regulator: If a single voltage is set with device tree then set apply_uV
Otherwise there is no way in the bindings to configure a fixed voltage
via software. It seems reasonable to assume that if the binding explicitly
specifies a voltage we want to actually use that voltage.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-05 18:59:10 +00:00
Mark Brown 9a8f5e0720 regulator: Allow regulators to register with no init_data
This allows read-only access to the device configuration which may be
useful for diagnostics.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
2011-11-30 09:38:28 +00:00
Mark Brown 979268cd32 Merge remote-tracking branches 'regulator/topic/dt' and 'regulator/for-linus' into regulator-next 2011-11-28 19:01:08 +00:00
Tero Kristo ba305e31e8 regulator: twl: fix twl4030 support for smps regulators
SMPS regulator voltage control differs from the one of the LDO ones.
Current TWL code was using LDO regulator ops for controlling the SMPS
regulators, which fails. This was fixed fixed by adding separate
regulator type which uses correct logic and calculations for the
voltage levels.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
2011-11-28 18:58:31 +00:00
Mark Brown 12f457dd78 Merge remote-tracking branch 'regulator/for-linus' into regulator-next 2011-11-28 14:50:45 +00:00
Lothar Waßmann 58fb5cf5d1 regulator: fix use after free bug
This is caused by dereferencing 'rdev' after device_unregister() in
the regulator_unregister() function.  'rdev' is freed by
device_unregister(), so it must not be dereferenced after this call.

[Edited commit message for legibility -- broonie]

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-28 14:44:38 +00:00
Mark Brown 9ee4be4156 Merge remote-tracking branch 'regulator/for-linus' into regulator-next 2011-11-28 11:49:56 +00:00
Axel Lin 005d610f2a regulator: Convert virtual and userspace regulator consumer drivers to use module_platform_driver()
This patch converts virtual and userspace regulator consumer drivers to use the
module_platform_driver() macro which makes the code smaller and a bit simpler.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-28 11:49:13 +00:00
Axel Lin a5228d2e5e regulator: aat2870: Remove a redundant bitwise and operation
The implementation in aat2870_update() already did the bitwise and operation
against mask parameter.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-28 11:49:10 +00:00
Axel Lin d4d6373c11 regulator: aat2870: Fix the logic of checking if no id is matched in aat2870_get_regulator
In current implementation, the pointer ri is not NULL if no id is matched.
Fix it by checking i == ARRAY_SIZE(aat2870_regulators) if no id is matched.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
2011-11-28 11:48:15 +00:00
Mark Brown ae523fc574 Merge remote-tracking branch 'regulator/topic/dt' into regulator-next 2011-11-27 19:47:03 +00:00
Axel Lin 22d881c068 regulator: Avoid potential NULL dereference in reg_fixed_voltage_probe()
of_get_fixed_voltage_config() may return NULL, return -ENOMEM in this case
so we don't dereference NULL pointer.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-27 19:46:31 +00:00
Mark Brown 6806a663b0 Merge remote-tracking branch 'regulator/topic/dt' into regulator-next 2011-11-27 11:36:16 +00:00
Axel Lin bc91396b0b regulator: Staticise of_get_fixed_voltage_config()
It is not used outside this driver so no need to make the symbol global.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-27 11:32:37 +00:00
Axel Lin 4b864af1a3 regulator: Checking return value of of_get_regulator_init_data
of_get_regulator_init_data() may return NULL, thus
check the return value to avoid NULL pointer dereference.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-27 11:29:21 +00:00
Axel Lin e69af5e967 regulator: export of_get_regulator_init_data
of_get_regulator_init_data is called in drivers/regulator/fixed.c
which could be a module.

Export of_get_regulator_init_data to fix below build error:
ERROR: "of_get_regulator_init_data" [drivers/regulator/fixed.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2

Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-27 11:29:21 +00:00
Mark Brown 02fcc84ae5 Merge remote-tracking branch 'regulator/topic/dt' into regulator-next 2011-11-24 10:49:38 +00:00
Rajendra Nayak 156843470c regulator: Fix compile break due to missing arguments to regulator_register
The commit 2c043bcbf2 ("regulator: pass additional of_node to
regulator_register()") caused a compile break because it missed
updating the regulator_register() call in gpio-regulator.c with
the additional parameter (NULL).

The compile break as reported by Stephen Rothwell with the
x86_64 allmodconfig looked like this

drivers/regulator/gpio-regulator.c: In function 'gpio_regulator_probe':
drivers/regulator/gpio-regulator.c:287:8: error: too few arguments to function 'regulator_register'
include/linux/regulator/driver.h:215:23: note: declared here

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-24 10:47:56 +00:00
Mark Brown 924ee2c962 Merge remote-tracking branch 'regulator/topic/dt' into regulator-next 2011-11-23 18:50:59 +00:00
Mark Brown 68aaa37d0e Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-next 2011-11-23 18:48:57 +00:00
Rajendra Nayak 69511a452e regulator: map consumer regulator based on device tree
Device nodes in DT can associate themselves with one or more
regulators/supply by providing a list of phandles (to regulator nodes)
and corresponding supply names.

For Example:
	devicenode: node@0x0 {
		...
		...
		vmmc-supply = <&regulator1>;
		vpll-supply = <&regulator2>;
	};

The driver would then do a regulator_get(dev, "vmmc"); to get
regulator1 and do a regulator_get(dev, "vpll"); to get
regulator2.

of_get_regulator() extracts the regulator node for a given
device, based on the supply name.

Use it to look up the regulator for a given consumer from device tree, during
a regulator_get(). If not found fallback and lookup through
the regulator_map_list instead.

Also, since the regulator dt nodes can use the same binding to
associate with a parent regulator/supply, allow the drivers to
specify a supply_name, which can then be used to lookup dt
to find the parent phandle.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-23 18:47:31 +00:00
Rajendra Nayak 2c043bcbf2 regulator: pass additional of_node to regulator_register()
With device tree support for regulators, its needed that the
regulator_dev->dev device has the right of_node attached.
To be able to do this add an additional parameter to the
regulator_register() api, wherein the dt-adapted driver can
then pass this additional info onto the regulator core.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-23 18:47:04 +00:00
Rajendra Nayak cef49102c1 regulator: adapt fixed regulator driver to dt
The fixed regulator driver uses of_get_fixed_voltage_config()
to extract fixed_voltage_config structure contents from device tree.

Also add documenation for additional bindings for fixed
regulators that can be passed through dt.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-23 18:47:00 +00:00
Rajendra Nayak 8f446e6fa1 regulator: helper routine to extract regulator_init_data
The helper routine is meant to be used by the regulator drivers
to extract the regulator_init_data structure from the data
that is passed from device tree.
'consumer_supplies' which is part of regulator_init_data is not extracted
as the regulator consumer mappings are passed through DT differently,
implemented in subsequent patches.
Similarly the regulator<-->parent/supply mapping is handled in
subsequent patches.

Also add documentation for regulator bindings to be used to pass
regulator_init_data struct information from device tree.

Some of the regulator properties which are linux and board specific,
are left out since its not clear if they can
be in someway embedded into the kernel or passed in from DT.
They will be revisited later.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-23 18:46:55 +00:00
Afzal Mohammed 780dc9ba4e regulator: TPS65910: Fix VDD1/2 voltage selector count
Count of selector voltage is required for regulator_set_voltage
to work via set_voltage_sel. VDD1/2 currently have it as zero,
so regulator_set_voltage won't work for VDD1/2.
Update count (n_voltages) for VDD1/2.

Output Voltage = (step value * 12.5 mV + 562.5 mV) * gain

With above expr, number of voltages that can be selected is
step value count * gain count

constant for gain count will be called VDD1_2_NUM_VOLT_COARSE

existing constant for step value count is VDD1_2_NUM_VOLTS,
use VDD1_2_NUM_VOLT_FINE instead to make clear that step value
is not the only component in deciding selectable voltage count

Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-23 14:03:52 +00:00
Mark Brown 4c78899b92 regulator: Don't create voltage sysfs entries if we can't read voltage
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-23 14:03:42 +00:00
Mark Brown aebe495895 regulator: Don't report zero volts for the fixed voltage regulator
If we don't know what voltage the regulator is set to return an error
rather than reporting zero volts.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-23 14:03:41 +00:00
Kyle Manna c1fc148024 regulator: TPS65910: Create an array for init data
Create an array of fixed size for the platform to pass regulator
initalization data through.

Passing an array of pointers to init data also allows more flexible
definition of init data as well as prevents reading past the end of the
array should the platform define an incorrectly sized array.

Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-23 14:02:48 +00:00
Kyle Manna 72c108cc49 regulator: TPS65910: Move regulator defs to header
Move the regulator defintions to the header so that platform board file
can use them to configure specific regulators.

Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-23 14:02:48 +00:00