Keep a STP port path cost value if it was set by a user.
Don't replace it with the link-speed based path cost
whenever the link goes down and comes back up.
Reported-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Obviously, vid should be considered when searching for multicast
group.
Cc: Vlad Yasevich <vyasevic@redhat.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an ability to configure a separate "untagged" egress
policy to the VLAN information of the bridge. This superseeds PVID
policy and makes PVID ingress-only. The policy is configured with a
new flag and is represented as a port bitmap per vlan. Egress frames
with a VLAN id in "untagged" policy bitmap would egress
the port without VLAN header.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN is added to the port, a local fdb entry for that port
(the entry with the mac address of the port) is added for that
VLAN. This way we can correctly determine if the traffic
is for the bridge itself. If the address of the port changes,
we try to change all the local fdb entries we have for that port.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a user adds bridge neighbors, allow him to specify VLAN id.
If the VLAN id is not specified, the neighbor will be added
for VLANs currently in the ports filter list. If no VLANs are
configured on the port, we use vlan 0 and only add 1 entry.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add vlan_id to multicasts groups so that we know which vlan
each group belongs to and can correctly forward to appropriate vlan.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds vlan to unicast fdb entries that are created for
learned addresses (not the manually configured ones). It adds
vlan id into the hash mix and uses vlan as an addditional parameter
for an entry match.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A user may designate a certain vlan as PVID. This means that
any ingress frame that does not contain a vlan tag is assigned to
this vlan and any forwarding decisions are made with this vlan in mind.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At ingress, any untagged traffic is assigned to the PVID.
Any tagged traffic is filtered according to membership bitmap.
At egress, if the vlan matches the PVID, the frame is sent
untagged. Otherwise the frame is sent tagged.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the RTM_GETLINK dump the vlan filter list of a given
bridge port. The information depends on setting the filter
flag similar to how nic VF info is dumped.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a netlink interface to add and remove vlan configuration on bridge port.
The interface uses the RTM_SETLINK message and encodes the vlan
configuration inside the IFLA_AF_SPEC. It is possble to include multiple
vlans to either add or remove in a single message.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bridge forwards a frame, make sure that a frame is allowed
to egress on that port.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a frame arrives on a port or transmitted by the bridge,
if we have VLANs configured, validate that a given VLAN is allowed
to enter the bridge.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds an optional infrustructure component to bridge that would allow
native vlan filtering in the bridge. Each bridge port (as well
as the bridge device) now get a VLAN bitmap. Each bit in the bitmap
is associated with a vlan id. This way if the bit corresponding to
the vid is set in the bitmap that the packet with vid is allowed to
enter and exit the port.
Write access the bitmap is protected by RTNL and read access
protected by RCU.
Vlan functionality is disabled by default.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And remove no longer used br->flags.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds empty br_mdb_init() and br_mdb_uninit() definitions in
br_private.h to avoid build failure when CONFIG_BRIDGE_IGMP_SNOOPING is not set.
These methods were moved from br_multicast.c to br_netlink.c by
commit 3ec8e9f085
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge fdb and link rtnl operations are registered in
core/rtnetlink. Bridge mdb operations are registred
in bridge/mdb. When removing bridge module, do not
unregister ALL PF_BRIDGE ops since that would remove
the ops from rtnetlink as well. Do remove mdb ops when
bridge is destroyed.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a flag to each mdb entry, so that we can distinguish
permanent entries with temporary entries.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implents adding/deleting mdb entries via netlink.
Currently all entries are temp, we probably need a flag to distinguish
permanent entries too.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Stephen mentioned, we need to monitor the mdb
changes in user-space, so add notifications via netlink too.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of rehashing, introduce a global variable 'br_mdb_rehash_seq'
which gets increased every time when rehashing, and assign
net->dev_base_seq + br_mdb_rehash_seq to cb->seq.
In theory cb->seq could be wrapped to zero, but this is not
easy to fix, as net->dev_base_seq is not visible inside
br_mdb_rehash(). In practice, this is rare.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
V5: fix two bugs pointed out by Thomas
remove seq check for now, mark it as TODO
V4: remove some useless #include
some coding style fix
V3: drop debugging printk's
update selinux perm table as well
V2: drop patch 1/2, export ifindex directly
Redesign netlink attributes
Improve netlink seq check
Handle IPv6 addr as well
This patch exports bridge multicast database via netlink
message type RTM_GETMDB. Similar to fdb, but currently bridge-specific.
We may need to support modify multicast database too (RTM_{ADD,DEL}MDB).
(Thanks to Thomas for patient reviews)
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
V3: make it a flag
V2: make the toggle per-port
Fast leave allows bridge to immediately stops the multicast
traffic on the port receives IGMP Leave when IGMP snooping is enabled,
no timeouts are observed.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
V2: make the toggle per-port
Fast leave allows bridge to immediately stops the multicast
traffic on the port receives IGMP Leave when IGMP snooping is enabled,
no timeouts are observed.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is Linux bridge implementation of root port guard.
If BPDU is received from a leaf (edge) port, it should not
be elected as root port.
Why would you want to do this?
If using STP on a bridge and the downstream bridges are not fully
trusted; this prevents a hostile guest for rerouting traffic.
Why not just use netfilter?
Netfilter does not track of follow spanning tree decisions.
It would be difficult and error prone to try and mirror STP
resolution in netfilter module.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is Linux bridge implementation of STP protection
(Cisco BPDU guard/Juniper BPDU block). BPDU block disables
the bridge port if a STP BPDU packet is received.
Why would you want to do this?
If running Spanning Tree on bridge, hostile devices on the network
may send BPDU and cause network failure. Enabling bpdu block
will detect and stop this.
How to recover the port?
The port will be restarted if link is brought down, or
removed and reattached. For example:
# ip li set dev eth0 down; ip li set dev eth0 up
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of issuing (0) statements when !CONFIG_SYSFS which will cause
'warning: ', we'll use inline statements instead. This will effectively
do the same thing, but suppress any unnecessary warnings.
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: bridge@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to ixgbe, ixgbevf, igbvf, igb and
networking core (bridge). Most notably is the addition of support
for local link multicast addresses in SR-IOV mode to the networking
core.
Also note, the ixgbe patch "ixgbe: Add support for pipeline reset" and
"ixgbe: Fix return value from macvlan filter function" is revised based
on community feedback.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware switches may support enabling and disabling the
loopback switch which puts the device in a VEPA mode defined
in the IEEE 802.1Qbg specification. In this mode frames are
not switched in the hardware but sent directly to the switch.
SR-IOV capable NICs will likely support this mode I am
aware of at least two such devices. Also I am told (but don't
have any of this hardware available) that there are devices
that only support VEPA modes. In these cases it is important
at a minimum to be able to query these attributes.
This patch adds an additional IFLA_BRIDGE_MODE attribute that can be
set and dumped via the PF_BRIDGE:{SET|GET}LINK operations. Also
anticipating bridge attributes that may be common for both embedded
bridges and software bridges this adds a flags attribute
IFLA_BRIDGE_FLAGS currently used to determine if the command or event
is being generated to/from an embedded bridge or software bridge.
Finally, the event generation is pulled out of the bridge module and
into rtnetlink proper.
For example using the macvlan driver in VEPA mode on top of
an embedded switch requires putting the embedded switch into
a VEPA mode to get the expected results.
-------- --------
| VEPA | | VEPA | <-- macvlan vepa edge relays
-------- --------
| |
| |
------------------
| VEPA | <-- embedded switch in NIC
------------------
|
|
-------------------
| external switch | <-- shiny new physical
------------------- switch with VEPA support
A packet sent from the macvlan VEPA at the top could be
loopbacked on the embedded switch and never seen by the
external switch. So in order for this to work the embedded
switch needs to be set in the VEPA state via the above
described commands.
By making these attributes nested in IFLA_AF_SPEC we allow
future extensions to be made as needed.
CC: Lennert Buytenhek <buytenh@wantstofly.org>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF_BRIDGE:RTM_{GET|SET}LINK nlmsg family and type are
currently embedded in the ./net/bridge module. This prohibits
them from being used by other bridging devices. One example
of this being hardware that has embedded bridging components.
In order to use these nlmsg types more generically this patch
adds two net_device_ops hooks. One to set link bridge attributes
and another to dump the current bride attributes.
ndo_bridge_setlink()
ndo_bridge_getlink()
CC: Lennert Buytenhek <buytenh@wantstofly.org>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SR-IOV mode the PF driver acts as the uplink port and is
used to send control packets e.g. lldpad, stp, etc.
eth0.1 eth0.2 eth0
VF VF PF
| | | <-- stand-in for uplink
| | |
--------------------------
| Embedded Switch |
--------------------------
|
MAC <-- uplink
But the embedded switch is setup to forward multicast addresses
to all interfaces both VFs and PF and onto the physical link.
This results in reserved MAC addresses used by control protocols
to be forwarded over the switch onto the VF.
In the LLDP case the PF sends an LLDPDU and it is currently
being forwarded to all the VFs who then see the PF as a peer.
This is incorrect.
This patch adds the multicast addresses to the RAR table in the
hardware to prevent this behavior.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Later changes need to be able to refer to neighbour attributes
when doing fdb_add.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal functions for add/deleting addresses don't change
their argument.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ensures that bridges created with brctl(8) or ioctl(2) directly
also carry IFLA_LINKINFO when dumped over netlink. This also allows
to create a bridge with ioctl(2) and delete it with RTM_DELLINK.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds two new flags NTF_MASTER and NTF_SELF that can
now be used to specify where PF_BRIDGE netlink commands should
be sent. NTF_MASTER sends the commands to the 'dev->master'
device for parsing. Typically this will be the linux net/bridge,
or open-vswitch devices. Also without any flags set the command
will be handled by the master device as well so that current user
space tools continue to work as expected.
The NTF_SELF flag will push the PF_BRIDGE commands to the
device. In the basic example below the commands are then parsed
and programmed in the embedded bridge.
Note if both NTF_SELF and NTF_MASTER bits are set then the
command will be sent to both 'dev->master' and 'dev' this allows
user space to easily keep the embedded bridge and software bridge
in sync.
There is a slight complication in the case with both flags set
when an error occurs. To resolve this the rtnl handler clears
the NTF_ flag in the netlink ack to indicate which sets completed
successfully. The add/del handlers will abort as soon as any
error occurs.
To support this new net device ops were added to call into
the device and the existing bridging code was refactored
to use these. There should be no required changes in user space
to support the current bridge behavior.
A basic setup with a SR-IOV enabled NIC looks like this,
veth0 veth2
| |
------------
| bridge0 | <---- software bridging
------------
/
/
ethx.y ethx
VF PF
\ \ <---- propagate FDB entries to HW
\ \
--------------------
| Embedded Bridge | <---- hardware offloaded switching
--------------------
In this case the embedded bridge must be managed to allow 'veth0'
to communicate with 'ethx.y' correctly. At present drivers managing
the embedded bridge either send frames onto the network which
then get dropped by the switch OR the embedded bridge will flood
these frames. With this patch we have a mechanism to manage the
embedded bridge correctly from user space. This example is specific
to SR-IOV but replacing the VF with another PF or dropping this
into the DSA framework generates similar management issues.
Examples session using the 'br'[1] tool to add, dump and then
delete a mac address with a new "embedded" option and enabled
ixgbe driver:
# br fdb add 22:35:19:ac:60:59 dev eth3
# br fdb
port mac addr flags
veth0 22:35:19:ac:60:58 static
veth0 9a:5f:81:f7:f6:ec local
eth3 00:1b:21:55:23:59 local
eth3 22:35:19:ac:60:59 static
veth0 22:35:19:ac:60:57 static
#br fdb add 22:35:19:ac:60:59 embedded dev eth3
#br fdb
port mac addr flags
veth0 22:35:19:ac:60:58 static
veth0 9a:5f:81:f7:f6:ec local
eth3 00:1b:21:55:23:59 local
eth3 22:35:19:ac:60:59 static
veth0 22:35:19:ac:60:57 static
eth3 22:35:19:ac:60:59 local embedded
#br fdb del 22:35:19:ac:60:59 embedded dev eth3
I added a couple lines to 'br' to set the flags correctly is all. It
is my opinion that the merit of this patch is now embedded and SW
bridges can both be modeled correctly in user space using very nearly
the same message passing.
[1] 'br' tool was published as an RFC here and will be renamed 'bridge'
http://patchwork.ozlabs.org/patch/117664/
Thanks to Jamal Hadi Salim, Stephen Hemminger and Ben Hutchings for
valuable feedback, suggestions, and review.
v2: fixed api descriptions and error case with both NTF_SELF and
NTF_MASTER set plus updated patch description.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sending general queries was implemented as an optimisation to speed
up convergence on start-up. In order to prevent interference with
multicast routers a zero source address has to be used.
Unfortunately these packets appear to cause some multicast-aware
switches to misbehave, e.g., by disrupting multicast packets to us.
Since the multicast snooping feature still functions without sending
our own queries, this patch will change the default to not send
queries.
For those that need queries in order to speed up convergence on start-up,
a toggle is provided to restore the previous behaviour.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it stands the bridge IGMP snooping system will respond to
group leave messages with queries for remaining membership.
This is both unnecessary and undesirable. First of all any
multicast routers present should be doing this rather than us.
What's more the queries that we send may end up upsetting other
multicast snooping swithces in the system that are buggy.
In fact, we can simply remove the code that send these queries
because the existing membership expiry mechanism doesn't rely
on them anyway.
So this patch simply removes all code associated with group
queries in response to group leave messages.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use IS_ENABLED(CONFIG_FOO)
instead of defined(CONFIG_FOO) || defined (CONFIG_FOO_MODULE)
Signed-off-by: Igor Maravić <igorm@etf.rs>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of testing defined(CONFIG_IPV6) || defined(CONFIG_IPV6_MODULE)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If user has configured a MAC address that is not one of the existing
ports of the bridge, then we need to add a special entry in the forwarding
table. This forwarding table entry has no outgoing port so it has to be
treated a little differently. The special entry is reported by the netlink
interface with ifindex of bridge, but ignored by the old interface since there
is no usable way to put it in the ABI.
Reported-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to cleanup bridge device timers and ports when being bridge
device is being removed via netlink.
This fixes the problem of observed when doing:
ip link add br0 type bridge
ip link set dev eth1 master br0
ip link set br0 up
ip link del br0
which would cause br0 to hang in unregister_netdev because
of leftover reference count.
Reported-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is based on an earlier patch by Nick Carter with comments
by David Lamparter but with some refinements. Thanks for their patience
this is a confusing area with overlap of standards, user requirements,
and compatibility with earlier releases.
It adds a new sysfs attribute
/sys/class/net/brX/bridge/group_fwd_mask
that controls forwarding of frames with address of: 01-80-C2-00-00-0X
The default setting has no forwarding to retain compatibility.
One change from earlier releases is that forwarding of group
addresses is not dependent on STP being enabled or disabled. This
choice was made based on interpretation of tie 802.1 standards.
I expect complaints will arise because of this, but better to follow
the standard than continue acting incorrectly by default.
The filtering mask is writeable, but only values that don't forward
known control frames are allowed. It intentionally blocks attempts
to filter control protocols. For example: writing a 8 allows
forwarding 802.1X PAE addresses which is the most common request.
Reported-by: David Lamparter <equinox@diac24.net>
Original-patch-by: Nick Carter <ncarter100@gmail.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Benjamin Poirier <benjamin.poirier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bridge topology with three systems:
+------+ +------+
| A(2) |--| B(1) |
+------+ +------+
\ /
+------+
| C(3) |
+------+
What is supposed to happen:
* bridge with the lowest ID is elected root (for example: B)
* C detects that A->C is higher cost path and puts in blocking state
What happens. Bridge with lowest id (B) is elected correctly as
root and things start out fine initially. But then config BPDU
doesn't get transmitted from A -> C. Because of that
the link from A-C is transistioned to the forwarding state.
The root cause of this is that the configuration messages
is generated with bogus message age, and dropped before
sending.
In the standardmessage_age is supposed to be:
the time since the generation of the Configuration BPDU by
the Root that instigated the generation of this Configuration BPDU.
Reimplement this by recording the timestamp (age + jiffies) when
recording config information. The old code incorrectly used the time
elapsed on the ageing timer which was incorrect.
See also:
https://bugzilla.vyatta.com/show_bug.cgi?id=7164
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note: netdev_update_features() needs only rtnl_lock as br->port_list
is only changed while holding it.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply restrictions on STP parameters based 802.1D 1998 standard.
* Fixes missing locking in set path cost ioctl
* Uses common code for both ioctl and sysfs
This is based on an earlier patch Sasikanth V but with overhaul.
Note:
1. It does NOT enforce the restriction on the relationship max_age and
forward delay or hello time because in existing implementation these are
set as independant operations.
2. If STP is disabled, there is no restriction on forward delay
3. No restriction on holding time because users use Linux code to act
as hub or be sticky.
4. Although standard allow 0-255, Linux only allows 0-63 for port priority
because more bits are reserved for port number.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use RTM_NEWNEIGH and RTM_DELNEIGH to allow updating of entries
in bridge forwarding table. This allows manipulating static entries
which is not possible with existing tools.
Example (using bridge extensions to iproute2)
# br fdb add 00:02:03:04:05:06 dev eth0
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows applications to query and monitor bridge forwarding
table in the same method used for neighbor table. The forward table
entries are returned in same structure format as used by the ioctl.
If more information is desired in future, the netlink method is
extensible.
Example (using bridge extensions to iproute2)
# br monitor
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger