Since an address in hash list has to already have a ref count,
no additional ref count is needed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link goes down, want address to be preserved but in a tentative
state, therefore it has to stay in hash list.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes preserve IPv6 address when link goes down (good).
But would cause address to point to dead dst entry (bad).
The simplest fix is to just not delete route if address is
being held for later use.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With latest CONFIG_PROVE_RCU stuff, I felt more comfortable to make this
work.
sk->sk_dst_cache is currently protected by a rwlock (sk_dst_lock)
This rwlock is readlocked for a very small amount of time, and dst
entries are already freed after RCU grace period. This calls for RCU
again :)
This patch converts sk_dst_lock to a spinlock, and use RCU for readers.
__sk_dst_get() is supposed to be called with rcu_read_lock() or if
socket locked by user, so use appropriate rcu_dereference_check()
condition (rcu_read_lock_held() || sock_owned_by_user(sk))
This patch avoids two atomic ops per tx packet on UDP connected sockets,
for example, and permits sk_dst_lock to be much less dirtied.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dont use netdev_warn() in dev_cap_txqueue() and get_rps_cpu() so that we
can catch following warnings without crash.
bond0.2240 received packet on queue 6, but number of RX queues is 1
bond0.2240 received packet on queue 11, but number of RX queues is 1
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the SO_TIMESTAMPING socket infrastructure for raw packet sockets.
We introduce PACKET_TX_TIMESTAMP for the control message cmsg_type.
Similar support for UDP and CAN sockets was added in commit
51f31cabe3
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in commit 04a0551c87
("loopback: Drop obsolete ip_summed setting") we stopped
setting CHECKSUM_UNNECESSARY in the loopback xmit.
This is because such a setting was a lie since it implies that the
checksum field of the packet is properly filled in.
Instead what happens normally is that CHECKSUM_PARTIAL is set and
skb->csum is calculated as needed.
But this was only happening for TCP data packets (via the
skb->ip_summed assignment done in tcp_sendmsg()). It doesn't
happen for non-data packets like ACKs etc.
Fix this by setting skb->ip_summed in the common non-data packet
constructor. It already is setting skb->csum to zero.
But this reminds us that we still have things like ip_output.c's
ip_dev_loopback_xmit() which sets skb->ip_summed to the value
CHECKSUM_UNNECESSARY, which Herbert's patch teaches us is not
valid. So we'll have to address that at some point too.
Signed-off-by: David S. Miller <davem@davemloft.net>
inet: Remove unused send_check length argument
This patch removes the unused length argument from the send_check
function in struct inet_connection_sock_af_ops.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Yinghai <yinghai.lu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: Handle CHECKSUM_PARTIAL for SYNACK packets for IPv6
This patch moves the common code between tcp_v6_send_check and
tcp_v6_gso_send_check into a new function __tcp_v6_send_check.
It then uses the new function in tcp_v6_send_synack as well as
tcp_v6_send_response so that they handle CHECKSUM_PARTIAL properly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Yinghai <yinghai.lu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: Handle CHECKSUM_PARTIAL for SYNACK packets for IPv4
This patch moves the common code between tcp_v4_send_check and
tcp_v4_gso_send_check into a new function __tcp_v4_send_check.
It then uses the new function in tcp_v4_send_synack so that it
handles CHECKSUM_PARTIAL properly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Yinghai <yinghai.lu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2626419ad5.
It causes regressions for people with IGB cards. Connection
requests don't complete etc. The true cause of the issue is
still not known, but we should sort this out in net-next-2.6
not net-2.6
Signed-off-by: David S. Miller <davem@davemloft.net>
As scan_work is queued from work_work it needs to be checked if scan
has been started during execution of work_work. Otherwise, when hw
scan is used, the stack gets error about hw being busy with ongoing
scan. This causes the stack to abort scan without notifying the driver
about it. This leads to a situation where the hw is scanning and the stack
thinks it's not. Then when the scan finishes, the stack will complain by
warnings.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We delay the skb linearising in ieee80211_rx_h_decrypt so that
frames do not require software decryption are not linearized. We
are safe to do this because ieee80211_get_mmie_keyidx() only
requires to touch nonlinear data for management frames, which are
already linearized before getting here.
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enhance tracing by adding tracing for a variety of
callbacks that the drivers call, and also for
internal calls (currently limited to queue status).
This can aid debugging what is going on in mac80211
in interaction with drivers, since we can now see
what drivers call and not just what mac80211 calls
in the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Grouped mesh action codes together with the other action codes in
ieee80211.h.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Back in commit 04a0551c87
("loopback: Drop obsolete ip_summed setting") we stopped
setting CHECKSUM_UNNECESSARY in the loopback xmit.
This is because such a setting was a lie since it implies that the
checksum field of the packet is properly filled in.
Instead what happens normally is that CHECKSUM_PARTIAL is set and
skb->csum is calculated as needed.
But this was only happening for TCP data packets (via the
skb->ip_summed assignment done in tcp_sendmsg()). It doesn't
happen for non-data packets like ACKs etc.
Fix this by setting skb->ip_summed in the common non-data packet
constructor. It already is setting skb->csum to zero.
But this reminds us that we still have things like ip_output.c's
ip_dev_loopback_xmit() which sets skb->ip_summed to the value
CHECKSUM_UNNECESSARY, which Herbert's patch teaches us is not
valid. So we'll have to address that at some point too.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits 5051ebd275 and
5051ebd275 ("ipv[46]: udp: optimize unicast RX
path") broke some programs.
After upgrading a L2TP server to 2.6.33 it started to fail, tunnels going up an
down, after the 10th tunnel came up. My modified rp-l2tp uses a global
unconnected socket bound to (INADDR_ANY, 1701) and one connected socket per
tunnel after parameter negotiation.
After ten sockets were open and due to mixed parameters to
udp[46]_lib_lookup2() kernel started to drop packets.
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coding style errors and warnings output while running checkpatch.pl
on the files net/core/ethtool.c and include/linux/ethtool.h
Signed-off-by: chavey <chavey@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current X.25 code has some bugs in throughput negotiation:
1. It does negotiation in all cases, usually there is no need
2. It incorrectly attempts to negotiate the throughput class in one
direction only. There are separate throughput classes for input
and output and if either is negotiated both mist be negotiates.
This is bug https://bugzilla.kernel.org/show_bug.cgi?id=15681
This bug was first reported by Daniel Ferenci to the linux-x25 mailing
list on 6/8/2004, but is still present.
The current (2.6.34) x.25 code doesn't seem to know that the X.25
throughput facility includes two values, one for the required
throughput outbound, one for inbound.
This causes it to attempt to negotiate throughput 0x0A, which is
throughput 9600 inbound and the illegal value "0" for inbound
throughput.
Because of this some X.25 devices (e.g. Cisco 1600) refuse to connect
to Linux X.25.
The following patch fixes this behaviour. Unless the user specifies a
required throughput it does not attempt to negotiate. If the user
does not specify a throughput it accepts the suggestion of the remote
X.25 system. If the user requests a throughput then it validates both
the input and output throughputs and correctly negotiates them with
the remote end.
Signed-off-by: John Hughes <john@calva.com>
Tested-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is a patch to stop X.25 examining fields beyond the end of the packet.
For example, when a simple CALL ACCEPTED was received:
10 10 0f
x25_parse_facilities was attempting to decode the FACILITIES field, but this
packet contains no facilities field.
Signed-off-by: John Hughes <john@calva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IGMP3 report parsing is looking at the wrong address for
group records. This patch fixes it.
Reported-by: Banyeer <banyeer@yahoo.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed by Randy Dunlap, we must include linux/proc_fs.h in
net/core/dev_addr_lists.c, regardless of CONFIG_PROC_FS
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>,
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WEP crypto was broken, but upon finding the problem
it is evident that other things were broken by the
paged RX patch as well.
To fix it, for now move the linearising in front.
This means that we linearise all frames, which is
not at all what we want, but at least it fixes the
problem for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few places in mac80211 do not currently acquire
the sta lock for RX aggregation, but they should.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The aggregation code has a number of quirks, like
inventing an unneeded WLAN_BACK_TIMER value and
leaking memory under certain circumstances during
station destruction. Fix these issues by using
the regular aggregation session teardown code and
blocking new aggregation sessions, all before the
station is really destructed.
As a side effect, this gets rid of the long code
block to destroy aggregation safely.
Additionally, rename tid_state_rx which can only
have the values IDLE and OPERATIONAL to
tid_active_rx to make it easier to understand
that there is no bitwise stuff going on on the
RX side -- the TX side remains because it needs
to keep track of the driver and peer states.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I want to use it during station destruction as well
so rename it to WLAN_STA_BLOCK_BA which is also the
only use of it now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All callers of ieee80211_sta_stop_rx_ba_session can
just call __ieee80211_stop_rx_ba_session instead
because they already have the station struct, so do
that and remove ieee80211_sta_stop_rx_ba_session.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All other places except one in the TX path, which
has BHs disabled, and it also cannot be locked from
interrupts so disabling IRQs is not necessary.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a station w/o a key is destroyed, or when
a driver submits work for a station and thereby
references it again, it seems like potentially
we could reference the station structure while
it is being destroyed.
Wait for an RCU grace period to elapse before
finishing destroying the station after we have
removed the station from the driver and from
the hash table etc., even in the case where no
key is associated with the station.
Also, there's no point in deleting the plink
timer here since it'll be properly deleted just
a bit later.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 is quite strict on allowing authentication and association
commands only in certain states. In order to meet these requirements,
user space applications may need to clear authentication or
association state in some cases. Currently, this can be done with
deauth/disassoc command, but that ends up sending out Deauthentication
or Disassociation frame unnecessarily. Add a new nl80211 attribute to
allow this sending of the frame be skipped, but with all other
deauth/disassoc operations being completed.
Similar state change is also needed for IEEE 802.11r FT protocol in
the FT-over-DS case which does not use Authentication frame exchange
in a transition to another BSS. For this to work with cfg80211, an
authentication entry needs to be created for the target BSS without
sending out an Authentication frame. The nl80211 authentication
command can be used for this purpose, too, with the new attribute to
indicate that the command is only for changing local state. This
enables wpa_supplicant to complete FT-over-DS transition successfully.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Speed up lookups by freeing flow cache entries later. After
virtualizing flow cache entry operations, the flow cache may now
end up calling policy or bundle destructor which can be slowish.
As gc_list is more effective with double linked list, the flow cache
is converted to use common hlist and list macroes where appropriate.
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Policies are now properly reference counted and destroyed from
all code paths. The delayed gc is just an overhead now and can
be removed.
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
__xfrm_lookup() is called for each packet transmitted out of
system. The xfrm_find_bundle() does a linear search which can
kill system performance depending on how many bundles are
required per policy.
This modifies __xfrm_lookup() to store bundles directly in
the flow cache. If we did not get a hit, we just create a new
bundle instead of doing slow search. This means that we can now
get multiple xfrm_dst's for same flow (on per-cpu basis).
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to validate the cached object before returning it.
It also allows to destruct object properly, if the last reference
was held in flow cache. This is also a prepartion for caching
bundles in the flow cache.
In return for virtualizing the methods, we save on:
- not having to regenerate the whole flow cache on policy removal:
each flow matching a killed policy gets refreshed as the getter
function notices it smartly.
- we do not have to call flow_cache_flush from policy gc, since the
flow cache now properly deletes the object if it had any references
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct timespec ts was alreay defined. Reuse the previously
defined one and reduce the memory footprint on the stack by
16 bytes.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it explicit in the API that all fields in subscriptions and events exchanged with the Topology Server must be in
network byte order.
It also ensures that all fields of a subscription are compared when cancelling a subscription, in order to avoid inadvertent
cancelling of the wrong subscription.
Finally, the tipc module version is updated to 2.0.0, to reflect the API change.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e34e09401ee9888dd662b2fca5d607794a56daf2 incorrectly removed
use of ieee80211_has_protected() from the management frame case and in
practice, made this validation drop all Action frames when MFP is
enabled. This should have only been done for frames with Protected
field set to zero.
Signed-off-by: Jouni Malinen <j@w1.fi>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new RCU lockdep support warns about these
in some contexts -- make it aware of the locks
used to protect all this. Different locks are
used in different contexts which unfortunately
means we can't get perfect checking.
Also remove rcu_dereference() from two places
that don't actually dereference the pointers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the problem introduced in commit
8404080568 which broke mesh peer link establishment.
changes:
v2 Added missing break (Johannes)
v3 Broke original patch into two (Johannes)
Signed-off-by: Javier Cardona <javier@cozybit.com>
Cc: stable@kernel.org
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
smc91c92_cs: fix the problem of "Unable to find hardware address"
r8169: clean up my printk uglyness
net: Hook up cxgb4 to Kconfig and Makefile
cxgb4: Add main driver file and driver Makefile
cxgb4: Add remaining driver headers and L2T management
cxgb4: Add packet queues and packet DMA code
cxgb4: Add HW and FW support code
cxgb4: Add register, message, and FW definitions
netlabel: Fix several rcu_dereference() calls used without RCU read locks
bonding: fix potential deadlock in bond_uninit()
net: check the length of the socket address passed to connect(2)
stmmac: add documentation for the driver.
stmmac: fix kconfig for crc32 build error
be2net: fix bug in vlan rx path for big endian architecture
be2net: fix flashing on big endian architectures
be2net: fix a bug in flashing the redboot section
bonding: bond_xmit_roundrobin() fix
drivers/net: Add missing unlock
net: gianfar - align BD ring size console messages
net: gianfar - initialize per-queue statistics
...
Fix kernel panic by NULL pointer dereference in the context of
ieee80211_ops->prepare_multicast().
This bug was introduced by commit 22bedad3c.. ("net: convert
multicast list to list_head").
Call __hw_addr_init() in ieee80211_alloc_hw() to initialize
list_head of private device multicast list, like we do in
bond_init().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noticed by Changli Gao, we must call local_irq_enable() after
rps_unlock()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix spin_unlock_irq which needs to be rps_unlock.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: saving negative to unsigned char
9p: return on mutex_lock_interruptible()
9p: Creating files with names too long should fail with ENAMETOOLONG.
9p: Make sure we are able to clunk the cached fid on umount
9p: drop nlink remove
fs/9p: Clunk the fid resulting from partial walk of the name
9p: documentation update
9p: Fix setting of protocol flags in v9fs_session_info structure.
Saving -EINVAL as unsigned char truncates the high bits and changes it
into 234 instead of -22. This breaks the test for "if (ret == -EINVAL)"
in parse_opts().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
RPC6 requires that it be possible to create endpoints that listen
exclusively for IPv4 or IPv6 connection requests. This is not currently
supported by the RDMA API.
This fixes a server RDMA regression introduced by 37498292a "NFSD:
Create PF_INET6 listener in write_ports".
Signed-off-by: Tom Tucker<tom@opengridcomputing.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
dcache prune happen on umount. So we cannot mark the client
satus disconnect. That will prevent a 9p call to the server
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Followup to commit 789a4a2c
(l2tp: Add support for static unmanaged L2TPv3 tunnels)
One missing init in l2tp_tunnel_sock_create() could access random kernel
memory, and a bit field should be unsigned.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ip_append() fails because of socket limit or memory shortage,
increment ICMP_MIB_OUTERRORS counter, so that "netstat -s" can report
these errors.
LANG=C netstat -s | grep "ICMP messages failed"
0 ICMP messages failed
For IPV6, implement ICMP6_MIB_OUTERRORS counter as well.
# grep Icmp6OutErrors /proc/net/dev_snmp6/*
/proc/net/dev_snmp6/eth0:Icmp6OutErrors 0
/proc/net/dev_snmp6/lo:Icmp6OutErrors 0
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for static (unmanaged) L2TPv3 tunnels, where
the tunnel socket is created by the kernel rather than being created
by userspace. This means L2TP tunnels and sessions can be created
manually, without needing an L2TP control protocol implemented in
userspace. This might be useful where the user wants a simple ethernet
over IP tunnel.
A patch to iproute2 adds a new command set under "ip l2tp" to make use
of this feature. This will be submitted separately.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing pppol2tp driver exports debug info to
/proc/net/pppol2tp. Rather than adding info to that file for the new
functionality added in this patch series, we add new files in debugfs,
leaving the old /proc file for backwards compatibility (L2TPv2 only).
Currently only one file is provided: l2tp/tunnels, which lists
internal debug info for all l2tp tunnels and sessions. More files may
be added later. The info is for debug and problem analysis only -
userspace apps should use netlink to obtain status about l2tp tunnels
and sessions.
Although debugfs does not support net namespaces, the tunnels and
sessions dumped in l2tp/tunnels are only those in the net namespace of
the process reading the file.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver presents a regular net_device for each L2TP ethernet
pseudowire instance. These interfaces are named l2tpethN by default,
though userspace can specify an alternative name when the L2TP
session is created, if preferred. When the pseudowire is established,
regular Linux networking utilities may be used to configure the
interface, i.e. give it IP address info or add it to a bridge. Any
data passed over the interface is carried over an L2TP tunnel.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reader/write locks are discouraged because they are slower than spin
locks. So this patch converts the rwlocks used in the per_net structs
to rcu.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In L2TPv3, we need to create/delete/modify/query L2TP tunnel and
session contexts. The number of parameters is significant. So let's
use netlink. Userspace uses this API to control L2TP tunnel/session
contexts in the kernel.
The previous pppol2tp driver was managed using [gs]etsockopt(). This
API is retained for backwards compatibility. Unlike L2TPv2 which
carries only PPP frames, L2TPv3 can carry raw ethernet frames or other
frame types and these do not always have an associated socket
family. Therefore, we need a way to use L2TP sessions that doesn't
require a socket type for each supported frame type. Hence netlink is
used.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This lets kernel modules which use genl netlink APIs serialize netlink
processing.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new L2TPIP socket family and modifies the core to
handle the case where there is no UDP header in the L2TP
packet. L2TP/IP uses IP protocol 115. Since L2TP/UDP and L2TP/IP
packets differ in layout, the datapath packet handling code needs
changes too. Userspace uses an L2TPIP socket instead of a UDP socket
when IP encapsulation is required.
We can't use raw sockets for this because the semantics of raw sockets
don't lend themselves to the socket-per-tunnel model - we need to
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes changes to the L2TP PPP code for L2TPv3.
The existing code has some assumptions about the L2TP header which are
broken by L2TPv3. Also the sockaddr_pppol2tp structure of the original
code is too small to support the increased size of the L2TPv3 tunnel
and session id, so a new sockaddr_pppol2tpv3 structure is needed. In
the socket calls, the size of this structure is used to tell if the
operation is for L2TPv2 or L2TPv3.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The L2TPv3 protocol changes the layout of the L2TP packet
header. Tunnel and session ids change from 16-bit to 32-bit values,
data sequence numbers change from 16-bit to 24-bit values and PPP-specific
fields are moved into protocol-specific subheaders.
Although this patch introduces L2TPv3 protocol support, there are no
userspace interfaces to create L2TPv3 sessions yet.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dumping L2TP PPP sessions using /proc/net/pppol2tp, get the
assigned PPP device name from PPP using ppp_dev_name().
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits the pppol2tp driver into separate L2TP and PPP parts
to prepare for L2TPv3 support. In L2TPv3, protocols other than PPP can
be carried, so this split creates a common L2TP core that will handle
the common L2TP bits which protocol support modules such as PPP will
use.
Note that the existing pppol2tp module is split into l2tp_core and
l2tp_ppp by this change.
There are no feature changes here. Internally, however, there are
significant changes, mostly to handle the separation of PPP-specific
data from the L2TP session and to provide hooks in the core for
modules like PPP to access.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the existing pppol2tp driver from drivers/net into a
new net/l2tp directory, which is where the upcoming L2TPv3 code will
live. The existing CONFIG_PPPOL2TP config option is left in its
current place to avoid "make oldconfig" issues when an existing
pppol2tp user takes this change. (This is the same approach used for
the pppoatm driver, which moved to net/atm.)
There are no code changes. The existing drivers/net/pppol2tp.c is
simply moved to net/l2tp.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
+little renaming of unicast functions to be smooth with multicast ones
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup to commit 5acbbd428d
(net: change illegal_highdma to use dma_mask)
If dev->dev.parent is NULL, we should not try to dereference it.
Dont force inline illegal_highdma() as its pretty big now.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Hancock pointed out two problems about NETIF_F_HIGHDMA:
-Many drivers only set the flag when they detect they can use 64-bit DMA,
since otherwise they could receive DMA addresses that they can't handle
(which on platforms without IOMMU/SWIOTLB support is fatal). This means that if
64-bit support isn't available, even buffers located below 4GB will get copied
unnecessarily.
-Some drivers set the flag even though they can't actually handle 64-bit DMA,
which would mean that on platforms without IOMMU/SWIOTLB they would get a DMA
mapping error if the memory they received happened to be located above 4GB.
http://lkml.org/lkml/2010/3/3/530
We can use the dma_mask if we need bouncing or not here. Then we can
safely fix drivers that misuse NETIF_F_HIGHDMA.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Group all per-cpu data to one structure instead of having many
globals. Also prepare the internals so that we can have multiple
instances of the flow cache if needed.
Only the kmem_cache is left as a global as all flow caches share
the same element size, and benefit from using a common cache.
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the code considers ->dead as a hint that the cached policy
needs to get refreshed. The read side can just drop the read lock
without any side effects.
The write side needs to make sure that it's written only exactly
once. Only possible race is at xfrm_policy_kill(). This is fixed
by checking result of __xfrm_policy_unlink() when needed. It will
always succeed if the policy object is looked up from the hash
list (so some checks are removed), but it needs to be checked if
we are trying to unlink policy via a reference (appropriate
checks added).
Since policy->walk.dead is written exactly once, it no longer
needs to be protected with a write lock.
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing check for policy direction verification. This is
especially important since without this xfrm_user may end up
deleting per-socket policy which is not allowed.
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xfrm state genid only needs to be matched against the copy
saved in xfrm_dst. So we don't need a global genid at all. In
fact, we don't even need to initialise it.
Based on observation by Timo Teräs.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
keep the old behavior on SMP without rps
RPS introduces a lock operation to per cpu variable input_pkt_queue on
SMP whenever rps is enabled or not. On SMP without RPS, this lock isn't
needed at all.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
net/core/dev.c | 42 ++++++++++++++++++++++++++++--------------
1 file changed, 28 insertions(+), 14 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
One of my test machine got a deadlock during "tc" sessions,
adding/deleting classes & filters, using traffic estimators.
After some analysis, I believe we have a potential use after free case
in est_timer() :
spin_lock(e->stats_lock); << HERE >>
read_lock(&est_lock);
if (e->bstats == NULL) << TEST >>
goto skip;
Test is done a bit late, because after estimator is killed, and before
rcu grace period elapsed, we might already have freed/reuse memory where
e->stats_locks points to (some qdisc->q.lock)
A possible fix is to respect a rcu grace period at Qdisc dismantle time.
On 64bit, sizeof(struct Qdisc) is exactly 192 bytes. Adding 16 bytes to
it (for struct rcu_head) is a problem because it might change
performance, given QDISC_ALIGNTO is 32 bytes.
This is why I also change QDISC_ALIGNTO to 64 bytes, to satisfy most
current alignment requirements.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check if error signaling is wanted (inet->recverr != 0) is done by
the caller: raw.c:raw_err() and udp.c:__udp4_lib_err(), so there is no
need to check this condition again.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent changes to add RCU lock verification to rcu_dereference() calls
caught out a problem with netlbl_unlhsh_hash(), see below.
===================================================
[ INFO: suspicious rcu_dereference_check() usage. ]
---------------------------------------------------
net/netlabel/netlabel_unlabeled.c:246 invoked rcu_dereference_check()
without protection!
This patch fixes this problem as well as others like it in the NetLabel
code. Also included in this patch is the identification of future work
to eliminate the RCU read lock in netlbl_domhsh_add(), but in the interest
of getting this patch out quickly that work will happen in another patch
to be finished later.
Thanks to Eric Dumazet and Paul McKenney for their help in understanding
the recent RCU changes.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Reported-by: David Howells <dhowells@redhat.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
check the length of the socket address passed to connect(2).
Check the length of the socket address passed to connect(2). If the
length is invalid, -EINVAL will be returned.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
net/bluetooth/l2cap.c | 3 ++-
net/bluetooth/rfcomm/sock.c | 3 ++-
net/bluetooth/sco.c | 3 ++-
net/can/bcm.c | 3 +++
net/ieee802154/af_ieee802154.c | 3 +++
net/ipv4/af_inet.c | 5 +++++
net/netlink/af_netlink.c | 3 +++
7 files changed, 20 insertions(+), 3 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bef5d1c70d split
ieee80211_drop_unencrypted() into separate functions that are used for
Data and Management frames. However, it did not handle the
RX_FLAG_DECRYPTED correctly for Management frames:
ieee80211_drop_unencrypted() can only return 0 for Management frames,
so there is no point in calling it here. Instead, just check the
status->flag directly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iw dev <devname> station del <MAC address> is quiet useful in mesh mode and should be possible.
Signed-off-by: Marco Porsch <marco.porsch@siemens.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When selecting the RX key for group-addressed robust management
frames, we do not actually select any BIP key if the frame is
unprotected (since we cannot find the key index from MMIE). This
results in the drop_unencrypted check in failing to drop the frame. It
is enough to verify that we have a STA entry for the transmitter and
that MFP is enabled for that STA; we do not need to check rx->key
here. This fixes BIP processing for unprotected, group-addressed,
robust management frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BIP (part of IEEE 802.11w) is only supposed to be used with
group-addressed frames. We ended up picking it as a default mechanism
for every management whenever we did not have a STA entry for the
destination (e.g., for Probe Response to a STA that is not
associated). While the extra MMIE in the end of management frames
should not break frames completed in most cases, there is no point in
doing this. Fix key selection to pick the default management key only
if the frame is sent to multicast/broadcast address and the frame is a
robust management frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When management frame protection (IEEE 802.11w) is used, the
deauthentication and disassociation frames must be protected whenever
the encryption keys are configured. We were removing the STA entry and
with it, the keys, just before actually sending out these frames which
meant that the frames went out unprotected. The AP will drop them in
such a case. Fix this by reordering the operations a bit so that
sta_info_destroy_addr() gets called only after
ieee80211_send_deauth_disassoc().
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calculate a running average of the signal strength reported for Beacon
frames and indicate cqm events if the average value moves below or
above the configured threshold value (and filter out repetitive events
with by using the configured hysteresis).
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable QoS explicitly, when user space AP program will setup a QoS
queues. Currently this is not needed as iwlwifi not work in AP mode
and no other driver implement enable/disable QoS.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add interface to disable/enable QoS (aka WMM or WME). Currently drivers
enable it explicitly when ->conf_tx method is called, and newer disable.
Disabling is needed for some APs, which do not support QoS, such
we should send QoS frames to them.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mac80211 drivers can now pass paged SKBs to mac80211 via
ieee80211_rx{_irqsafe}. The implementation currently use
skb_linearize() in a few places i.e. management frame
handling, software decryption, defragmentation and A-MSDU
process. We will optimize them one by one later.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Cc: Kalle Valo <kalle.valo@iki.fi>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove duplicate declaration of symbol: struct hlist_node *node was
already declared, the seconds declaration shadows the first one.
CC: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct _zone *tipc_zones has local scope level and
should defined with the correct scoping.
CC: Per Liden <per.liden@nospam.ericsson.com>
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coding style errors and warnings output while running checkpatch.pl
on the file net/core/dst.c.
Signed-off-by: chavey <chavey@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds ethtool and device feature flag to allow control
of receive hashing offload.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger
Eric Dumazet
Richard Cochran
Linus Torvalds
David S. Miller
Herbert Xu
Teemu Paasikivi
Luis R. Rodriguez
Zhu Yi
Johannes Berg
Javier Cardona
Jorge Boncompte [DTI2]
John W. Linville
chavey
John Hughes
Johannes Berg
Jouni Malinen
Timo Teräs
Hagen Paul Pfeifer
Jon Paul Maloy
YOSHIFUJI Hideaki / 吉藤英明
Tom Herbert
Dan Carpenter
Tom Tucker
Aneesh Kumar K.V
Brian Haley
James Chapman
Jiri Pirko
FUJITA Tomonori
Changli Gao
Paul Moore
Stephen Rothwell
Marco Porsch
Stanislaw Gruszka
Frans Pop