Recent changes to tighten the check for UARTs that don't correctly
re-assert THRE (01c194d927: "serial 8250:
tighten test for using backup timer") caused problems when such a UART was
opened for the second time - the bug could only successfully be detected
at first initialization. For users of this version of this particular
UART IP it is fatal.
This patch stores the information about the bug in the bugs field of the
port structure when the port is first started up so subsequent opens can
check this bit even if the test for the bug fails.
David Brownell: "My own exposure to this is that the UART on DaVinci
hardware, which TI allegedly derived from its original 16550 logic, has
periodically gone from working to unusable with the mainline 8250.c ...
and back and forth a bunch. Currently it's "unusable", a regression from
some previous versions. With this patch from Will, it's usable."
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Alex Williamson <alex.williamson@hp.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Cc: <stable@kernel.org> [2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The interrupt handler for muxed interrupts (imx2/imx3) was calling
the rts handling subroutine if the RTSS bit was set.
(Which indicates the status of the RTS line), leading to an
interrupt flood on RTS bit low.
This patch fixes the problem by looking at the RTSD bit instead,
indicating a change in the RTS line.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
RX in i.MX27 and i.MX31 UART lines does not work unless the
"RXD Muxed Input Select" bit is set on i.MX27 and i.MX31 processors.
This patch sets the missing RXD mux bit in the UCR3 register.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adds extra "out" label to probe function after calling .init form platform data.
Because .init can return error number caused by gpio request fail.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* master.kernel.org:/home/rmk/linux-2.6-arm: (38 commits)
[ARM] 5191/1: ARM: remove CVS keywords
[ARM] pxafb: fix the warning of incorrect lccr when lcd_conn is specified
[ARM] pxafb: add flag to specify output format on LDD pins when base is RGBT16
[ARM] pxafb: fix the incorrect configuration of GPIO77 as ACBIAS for TFT LCD
[ARM] 5198/1: PalmTX: PCMCIA fixes
[ARM] Fix a pile of broken watchdog drivers
[ARM] update mach-types
[ARM] 5196/1: fix inline asm constraints for preload
[ARM] 5194/1: update .gitignore
[ARM] add proc-macros.S include to proc-arm940 and proc-arm946
[ARM] 5192/1: ARM TLB: add v7wbi_{possible,always}_flags to {possible,always}_tlb_flags
[ARM] 5193/1: Wire up missing syscalls
[ARM] traps: don't call undef hook functions with spinlock held
[ARM] 5183/2: Provide Poodle LoCoMo GPIO names
[ARM] dma-mapping: provide sync_range APIs
[ARM] dma-mapping: improve type-safeness of DMA translations
[ARM] Kirkwood: instantiate the orion_spi driver in the platform code
[ARM] prevent crashing when too much RAM installed
[ARM] Kirkwood: Instantiate mv_xor driver
[ARM] Orion: Instantiate mv_xor driver for 5182
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Handle stack trace attempts before irqstacks are setup.
sparc64: Implement IRQ stacks.
sparc: remove include of linux/of_device.h from asm/of_device.h
sparc64: Fix recursion in stack overflow detection handling.
sparc/drivers: use linux/of_device.h instead of asm/of_device.h
sparc64: Don't MAGIC_SYSRQ ifdef smp_fetch_global_regs and support code.
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It now compiles with the tty changes but isn't tested (which has to be
better than not compiling..
Closes bug #11218
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Blackfin peers into the ldisc in an odd way for IRDA snooping which
therefore got missed. Simple enough fix.
Closes bug #11233
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (28 commits)
mm/hugetlb.c must #include <asm/io.h>
video: Fix up hp6xx driver build regressions.
sh: defconfig updates.
sh: Kill off stray mach-rsk7203 reference.
serial: sh-sci: Fix up SH7760/SH7780/SH7785 early printk regression.
sh: Move out individual boards without mach groups.
sh: Make sure AT_SYSINFO_EHDR is exposed to userspace in asm/auxvec.h.
sh: Allow SH-3 and SH-5 to use common headers.
sh: Provide common CPU headers, prune the SH-2 and SH-2A directories.
sh/maple: clean maple bus code
sh: More header path fixups for mach dir refactoring.
sh: Move out the solution engine headers to arch/sh/include/mach-se/
sh: I2C fix for AP325RXA and Migo-R
sh: Shuffle the board directories in to mach groups.
sh: dma-sh: Fix up dreamcast dma.h mach path.
sh: Switch KBUILD_DEFCONFIG to shx3_defconfig.
sh: Add ARCH_DEFCONFIG entries for sh and sh64.
sh: Fix compile error of Solution Engine
sh: Proper __put_user_asm() size mismatch fix.
sh: Stub in a dummy ENTRY_OFFSET for uImage offset calculation.
...
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Lockless get_user_pages_fast() for 64-bit (v3)
powerpc: Don't use the wrong thread_struct for ptrace get/set VSX regs
powerpc: Fix ptrace buffer size for VSX
powerpc: Correctly hookup PTRACE_GET/SETVSRREGS for 32 bit processes
ide/powermac: Fix use of uninitialized pointer on media-bay
powerpc: Allow non-hcall return values for lparcfg writes
ipmi/powerpc: Use linux/of_{device,platform}.h instead of asm
powerpc/fsl: proliferate simple-bus compatibility to soc nodes
Documentation: remove old sbc8260 board specific information
cpm2: Rework baud rate generators configuration to support external clocks.
powerpc: rtc_cmos_setup: assign interrupts only if there is i8259 PIC
cpm_uart: Add generic clock API support to set baudrates
cpm_uart: Modem control lines support
powerpc: implement GPIO LIB API on CPM1 Freescale SoC.
cpm2: Implement GPIO LIB API on CPM2 Freescale SoC.
powerpc: Fix 8xx build failure
powerpc: clean up the Book-E HW watchpoint support
The removal of drivers/serial/v850e_uart.c originally was in my v850
removal patch, but it seems it got lost somewhere.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
serial8250_startup() doesn't disable interrupts while taking the &up->port.lock
which might race against the interrupt handler serial8250_interrupt(), which
when entered, will deadlock waiting for the lock to be released.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As noted by Manuel:
Commit c63847a362 ("sh: Add
SCIF2 support for SH7763.") broke build with CONFIG_EARLY_PRINTK
enabled for me (SH7760):
CC arch/sh/kernel/early_printk.o
/mnt/work/sh7760/kernel/linux-2.6.git/arch/sh/kernel/early_printk.c: In function 'scif_sercon_putc':
/mnt/work/sh7760/kernel/linux-2.6.git/arch/sh/kernel/early_printk.c:84: error: implicit declaration of function 'sci_SCFDR_in'
Move the SH7763 definitions out on their own, so they don't create additional
confusion within the SH7760/SH7780/SH7785 block. Restore the deleted
SCFDR definition for these parts.
Reported-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch introduces baudrate setting support via the generic clock API.
When present the optional device tree clock property is used instead of
fsl-cpm-brg. Platforms can then define complex clock schemes, to output
the serial clock on an external pin for instance.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch replaces the get_mctrl/set_mctrl stubs with modem control line
read/write access through the GPIO lib.
Available modem control lines are described in the device tree using GPIO
bindings. The driver expect a GPIO pin for each of the CTS, RTS, DCD, DSR,
DTR and RI signals. Unused control lines can be left out.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SH7763 has 3 SCIF device. Current code supports SCIF0 and 1.
SCIF0 and 1 are same register constitution, but only SCIF2 is different.
I added support of SCIF2.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Before setting STOP_TX, set _brkcr to 0 so the SMC does not send a break
character. The driver appears to properly re-initialize _brkcr when the
SMC is restarted.
Do not interrupt RX/TX when the termios is being adjusted; it results in
corrupted characters appearing on the line.
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changes to the generic console support code that happened a while ago
introduced a scenario where the initial console is used in parallel with
the final console during a brief period when switching between the two is
in progress. During that time a message about the switch-over is printed.
With some combinations of chips, firmware and drivers, such as the DEC
DZ11 clone used with the DECstation, a hang may happen because the
firmware used for the initial console may not expect the state of the chip
after it has been initialised by the driver.
This is a workaround for the DZ11 which reuses the power-management
callback to keep the transmitter of the line associated with the console
enabled. It reflects the consensus reached in a discussion a while ago.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changes to the generic console support code that happened a while ago
introduced a scenario where the initial console is used in parallel with
the final console during a brief period when switching between the two is
in progress. During that time a message about the switch-over is printed.
With some combinations of chips, firmware and drivers, such as the Zilog
Z85C30 SCC used with the DECstation, a hang may happen because the
firmware used for the initial console may not expect the state of the chip
after it has been initialised by the driver. This is not a bug in the
firmware, as some registers it would have to examine are write-only.
This is a workaround for the Z85C30 which reuses the power-management
callback to keep the transmitter of the line associated with the console
enabled. It reflects the consensus reached in a discussion a while ago.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is a no-name PCI card. I found no reference to a producer so I used
"UNKNOWN_0x1584" as the name.
Full lspci:
01:07.0 0780: 10b5:9050 (rev 01)
Subsystem: 10b5:1584
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- \
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- \
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 1: I/O ports at ec00 [size=128]
Region 2: I/O ports at e480 [size=32]
Region 3: I/O ports at e400 [size=8]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA \
PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] #06 [0080]
Capabilities: [4c] Vital Product Data
After:
0000:01:07.0: ttyS4 at I/O 0xe480 (irq = 10) is a 16550A
0000:01:07.0: ttyS5 at I/O 0xe488 (irq = 10) is a 16550A
0000:01:07.0: ttyS6 at I/O 0xe490 (irq = 10) is a 16550A
0000:01:07.0: ttyS7 at I/O 0xe498 (irq = 10) is a 16550A
Signed-off-by: Catalin(ux) M BOIE <catab@embedromix.ro>
Acked-by: Alan Cox <alan@redhat.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel 82571 has a "Serial Over LAN" feature that doesn't properly
implements the receiving of break characters. When a break is received,
it doesn't set UART_LSR_DR and unless another character is received, the
break won't be received by the application.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the missing MODULE_LICENSE("GPL").
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trying to compile the v850 port brings many compile errors, one of them exists
since at least kernel 2.6.19.
There also seems to be noone willing to bring this port back into a usable
state.
This patch therefore removes the v850 port.
If anyone ever decides to revive the v850 port the code will still be
available from older kernels, and it wouldn't be impossible for the port to
reenter the kernel if it would become actively maintained again.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add in console polling hooks for the cpm uart for use with kgdb and
kgdboc.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: galak@kernel.crashing.org
I missed the cpm_uart one. Thanks to Kumar Gala for reporting it. A double
check found samsung also needed fixing up.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With SMP kernels _irqsave spinlock disables only local interrupts, while
the shared serial interrupt could be assigned to the CPU that is not
currently starting up the serial port.
This might cause issues because serial8250_startup() routine issues
IRQ-triggering operations before registering the port in the IRQ chain
(though, this is fine to do and done explicitly because we don't want to
process any interrupts on the port startup).
With RT kernels and preemptable hardirqs, _irqsave spinlock does not
disable local hardirqs, and the bug could be reproduced much easily:
$ cat /dev/ttyS0 &
$ cat /dev/ttyS1
irq 42: nobody cared (try booting with the "irqpoll" option)
Call Trace:
[C0475EB0] [C0008A98] show_stack+0x4c/0x1ac (unreliable)
[C0475EF0] [C004BBD4] __report_bad_irq+0x34/0xb8
[C0475F10] [C004BD38] note_interrupt+0xe0/0x308
[C0475F50] [C004B09C] thread_simple_irq+0xdc/0x104
[C0475F70] [C004B3FC] do_irqd+0x338/0x3c8
[C0475FC0] [C00398E0] kthread+0xf8/0x100
[C0475FF0] [C0011FE0] original_kernel_thread+0x44/0x60
handlers:
[<c02112c4>] (serial8250_interrupt+0x0/0x138)
Disabling IRQ #42
After this, all serial ports on the given IRQ are non-functional.
To fix the issue we should explicitly disable shared IRQ before
issuing any IRQ-triggering operations.
I also changed spin_lock_irqsave to the ordinary spin_lock, since it
seems to be safe: chain does not contain new port (yet), thus nobody
will interfere us from the ISRs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some hardware needs to do break handling itself and may have partial
support only. Make break_ctl return an error code. Add a tty driver flag
so you can indicate driver hardware side break support.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tty pointer has been moved into a tty_port field, so we need to use
->info->port.tty instead of just ->info->tty. Fixes these build errors:
David Brownell <david-b@pacbell.net> wrote:
> drivers/serial/atmel_serial.c: In function 'atmel_rx_from_ring':
> drivers/serial/atmel_serial.c:665: error: 'struct uart_info' has no member named 'tty'
> drivers/serial/atmel_serial.c: In function 'atmel_rx_from_dma':
> drivers/serial/atmel_serial.c:672: error: 'struct uart_info' has no member named 'tty'
> drivers/serial/atmel_serial.c: In function 'atmel_startup':
> drivers/serial/atmel_serial.c:797: error: 'struct uart_info' has no member named 'tty'
> make[2]: *** [drivers/serial/atmel_serial.o] Error 1
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The below is the patch to replace blindly all possible places,
including Jack's fixes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
(Reviewed and checked rather than blindly added)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix compile errors in SGI console drivers caused by changes to the
tty_port structures in the linux-next tree.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Today's linux-next build (powerpc allyesconfig) failed like this:
drivers/serial/pmac_zilog.c: In function 'pmz_receive_chars':
drivers/serial/pmac_zilog.c:245: error: 'struct uart_info' has no member named 'tty'
drivers/serial/pmac_zilog.c:250: error: 'struct uart_info' has no member named 'tty'
I applied the patch below (which builds but may, or may not, be correct).
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.auhttp://www.canb.auug.org.au/~sfr/
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Today's linux-next build (sparc64 defconfig) failed like this:
drivers/serial/sunhv.c: In function `receive_chars':
drivers/serial/sunhv.c:188: error: structure has no member named `tty'
drivers/serial/sunsu.c: In function `receive_chars':
drivers/serial/sunsu.c:314: error: structure has no member named `tty'
drivers/serial/sunsab.c: In function `receive_chars':
drivers/serial/sunsab.c:121: error: structure has no member named `tty'
I applied the following patch (which, again, may not be correct).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch the serial_core based drivers to use the new tty_port structure.
We can't quite use all of it yet because of the dynamically allocated
extras in the serial_core layer.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes CVS keywords that weren't updated for a long time in
comments, printk's and MODULE_DESCRIPTION's (no printk's or
MODULE_DESCRIPTION's are completely removed).
While doing this I also found and fixed a missing \n in a printk
in m32r_sio.c
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid dumping garbage to the serial port when the tty is flushed. This
tends to happen when rebooting from a serial console.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Serial drivers using DMA (like the atmel_serial driver) tend to get very
confused when the xmit buffer is flushed and nobody told them. They
also tend to spew a lot of garbage since the DMA engine keeps running
after the buffer is flushed and possibly refilled with unrelated data.
This patch adds a new flush_buffer operation to the uart_ops struct,
along with a call to it from uart_flush_buffer() right after the xmit
buffer has been cleared. The driver can implement this in order to
syncronize its internal DMA state with the xmit buffer when the buffer
is flushed.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As part of a heuristic to identify modem devices, 8250_pnp.c
checks to see whether a device can be configured at any of the
legacy COM port addresses.
This patch moves the code that traverses the PNP "possible resource
options" from 8250_pnp.c to the PNP subsystem. This encapsulation
is important because a future patch will change the implementation
of those resource options.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The SERIAL_SAMSUNG needs SERIAL_CORE but doesn't select it, leading to a
build failure. Adding a 'select SERIAL_CORE' cure the trouble.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
