The DCS_DATAPATH_BUSY bit used to monitor the completion of DC servo
operations has been deprecated and with some more recente revisions
may perform incorrectly, especially when only analogue bypass paths
are in use. Switch to using readback from the DC servo command
register instead, which is supported for all devices. Without this
unacceptably long timeouts may be observed in some circumstances.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
If we need to offset correct the DC servo then don't use runtime
recalibration since that is likely to introduce further offsets
which will be evident on powerdown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
More recent Wolfson hubs devices add the ability to read back the DC
servo calibration information from the register used to write offsets,
and later still ones remove the old readback registers. Add support
for the new scheme, and use it for WM8994 device revisions that
support it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
If the correction wraps around then a substantial offset would be
introduced.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
We're keeping track of the number of times we've iterated but never
actually using this to bail out if the chip looks stuck.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Perform DC servo offset calibration using a series update sequence
rather than startup update sequence, tuning the configuration of the
WM8993 DC servo to make best use of this.
Also introduce currently unused data allowing us to correct for
any systematic errors in the DC servo calibration results and an
alternative startup path for the headphone output which performs
better with some chip revisions. The alternative setup sequence is
enabled for WM8993.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This provides a small power saving when audio is inactive.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This renames from a character / to : of controls. A / occurs below error
messages.
ASoC: Failed to create IN2RP/VXRP debugfs file
ASoC: Failed to create IN2LP/VXRN debugfs file
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Avoids potential issues if we read back unexpected values during
a read/modify/write cycle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8993 analogue control is shared with other devices in the same
product line. Since this is a very substantial proportion of the
driver move the definitions of these controls into a new wm_hubs module
which allows them to be shared between the two.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown
Joonyoung Shim
Takashi Iwai