In preparation of dropping interconnect target module platform data in
favor of devicetree based data, we must pass swsup idle quirks to the
platform data functions.
For now, let's only tag the UART modules with the SWSUP_SIDLE_ACT quirk.
The other modules will get tagged with swsup quirks as we drop the
platform data and test the changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We cannot access mcpdm registers at all unless there is an optional pdmclk
configured. As this is currently only needed for mcpdm, let's check for
mcpdm in sysc_get_clocks(). If it turns out to be needed for other modules
too, we can add more flags to the quirks table for this.
Signed-off-by: Tony Lindgren <tony@atomide.com>
At least mcpdm needs an optional external clock enabled to function and
this clock typically comes from the PMIC. We can detect mcpdm based on
the interconnect target module address and set a quirk flag early.
To do this, let's initialize the clocks a bit later and add a new
function for sysc_init_early_quirks(). Note that we cannot yet enable
the early quirks for mcpdm until the optional external clocks are
handled in the in the following patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can do the rsstctrl a bit later, but need to deassert rstctrl reset
before the clocks are enabled if asserted. Let's only init restctrl
in sysc_init_resets() and do the reset later on just before we enable
the device clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are currently not managing interconnect target module clocks in the
for legacy platform data based case. This causes a problem for using the
platform data based functions when dropping the platform data for the
interconnect target module configuration.
To avoid a situation where we need to populate the main and optional
clocks also for the platform data based functions, let's just manage the
clocks directly in ti-sysc driver. This means that until the interconnect
target module confugration platform data is dropped our use count for
clk_enable() will be 2 instead of 1.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The platform data based init functions typically reset the interconnect
target module configure the registers. As we may need the interconnect
target module specific quirks configured based on the revision register,
we want to move the platform data based init to happen later.
Let's allocate mdata as needed so it's available for sysc_legacy_init()
that we call with module clocks enabled from sysc_init_module().
Signed-off-by: Tony Lindgren <tony@atomide.com>
The first thing we want to do is just read the module revision register to
be able to configure the module specific quirks and configure the module
registers.
As the interconnect target module may not yet be properly configured and
may need a reset first, we don't want to use pm_runtime_get() at this
point.
To read the revision register, let's just enable the all the clocks for
the interconnect target module during init even if the optional clocks
are not needed. That way we can read the revision register to configure
the quirks needed for PM runtime.
Signed-off-by: Tony Lindgren <tony@atomide.com>
At least McPDM module depends on an external optional clock to be
usable. To make handling of the McPDM clock easier in the following
patches, let's add separate functions for handling the main clocks
and the optional clocks.
Let's also add error handling to shut down already enabled clocks
while at it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have ti,no-idle in use in addition to ti,no-idle-on-init but we're
missing handling for it in the ti-sysc interconnect target module driver.
Let's also group the idle defines together and update the binding
documentation for it.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If we return early before ddata->clocks have been allocated we will get a
NULL pointer dereference in sysc_unprepare(). Let's fix this by returning
early when no clocks are allocated.
Fixes: 0eecc636e5 ("bus: ti-sysc: Add minimal TI sysc interconnect target driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
pm_runtime_force_suspend() and pm_runtime_force_resume() are used as system
sleep noirq suspend and resume callbacks. If the driver is active till late
suspend, where runtime PM cannot run, force suspend is essential for the
device. This makes sure that the device is put into low power state during
system wide PM transitions to sleep states.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
aconnect bus driver is using pm_clk_*() interface for managing clocks.
With this, clocks seem to be always ON. This happens on Tegra devices
which use BPMP co-processor to manage clock resources, where clocks
are enabled during prepare phase. This is necessary because calls to
BPMP are always blocking. When pm_clk_*() interface is used on such
Tegra devices, clock prepare count is not balanced till driver remove()
gets executed and hence clocks are seen ON always. Thus this patch
replaces pm_clk_*() with devm_clk_*() framework.
Suggested-by: Mohan Kumar D <mkumard@nvidia.com>
Reviewed-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As usual, the drivers/tee and drivers/reset subsystems get merged
here, with the expected set of smaller updates and some new hardware
support. The tee subsystem now supports device drivers to be attached
to a tee, the first example here is a random number driver with its
implementation in the secure world.
Three new power domain drivers get added for specific chip families:
- Broadcom BCM283x chips (used in Raspberry Pi)
- Qualcomm Snapdragon phone chips
- Xilinx ZynqMP FPGA SoCs
One new driver is added to talk to the BPMP firmware on NVIDIA
Tegra210
Existing drivers are extended for new SoC variants from NXP,
NVIDIA, Amlogic and Qualcomm.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=+DOl
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, the drivers/tee and drivers/reset subsystems get merged
here, with the expected set of smaller updates and some new hardware
support. The tee subsystem now supports device drivers to be attached
to a tee, the first example here is a random number driver with its
implementation in the secure world.
Three new power domain drivers get added for specific chip families:
- Broadcom BCM283x chips (used in Raspberry Pi)
- Qualcomm Snapdragon phone chips
- Xilinx ZynqMP FPGA SoCs
One new driver is added to talk to the BPMP firmware on NVIDIA
Tegra210
Existing drivers are extended for new SoC variants from NXP, NVIDIA,
Amlogic and Qualcomm"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (113 commits)
tee: optee: update optee_msg.h and optee_smc.h to dual license
tee: add cancellation support to client interface
dpaa2-eth: configure the cache stashing amount on a queue
soc: fsl: dpio: configure cache stashing destination
soc: fsl: dpio: enable frame data cache stashing per software portal
soc: fsl: guts: make fsl_guts_get_svr() static
hwrng: make symbol 'optee_rng_id_table' static
tee: optee: Fix unsigned comparison with less than zero
hwrng: Fix unsigned comparison with less than zero
tee: fix possible error pointer ctx dereferencing
hwrng: optee: Initialize some structs using memset instead of braces
tee: optee: Initialize some structs using memset instead of braces
soc: fsl: dpio: fix memory leak of a struct qbman on error exit path
clk: tegra: dfll: Make symbol 'tegra210_cpu_cvb_tables' static
soc: qcom: llcc-slice: Fix typos
qcom: soc: llcc-slice: Consolidate some code
qcom: soc: llcc-slice: Clear the global drv_data pointer on error
drivers: soc: xilinx: Add ZynqMP power domain driver
firmware: xilinx: Add APIs to control node status/power
dt-bindings: power: Add ZynqMP power domain bindings
...
Pull crypto update from Herbert Xu:
"API:
- Add helper for simple skcipher modes.
- Add helper to register multiple templates.
- Set CRYPTO_TFM_NEED_KEY when setkey fails.
- Require neither or both of export/import in shash.
- AEAD decryption test vectors are now generated from encryption
ones.
- New option CONFIG_CRYPTO_MANAGER_EXTRA_TESTS that includes random
fuzzing.
Algorithms:
- Conversions to skcipher and helper for many templates.
- Add more test vectors for nhpoly1305 and adiantum.
Drivers:
- Add crypto4xx prng support.
- Add xcbc/cmac/ecb support in caam.
- Add AES support for Exynos5433 in s5p.
- Remove sha384/sha512 from artpec7 as hardware cannot do partial
hash"
[ There is a merge of the Freescale SoC tree in order to pull in changes
required by patches to the caam/qi2 driver. ]
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (174 commits)
crypto: s5p - add AES support for Exynos5433
dt-bindings: crypto: document Exynos5433 SlimSSS
crypto: crypto4xx - add missing of_node_put after of_device_is_available
crypto: cavium/zip - fix collision with generic cra_driver_name
crypto: af_alg - use struct_size() in sock_kfree_s()
crypto: caam - remove redundant likely/unlikely annotation
crypto: s5p - update iv after AES-CBC op end
crypto: x86/poly1305 - Clear key material from stack in SSE2 variant
crypto: caam - generate hash keys in-place
crypto: caam - fix DMA mapping xcbc key twice
crypto: caam - fix hash context DMA unmap size
hwrng: bcm2835 - fix probe as platform device
crypto: s5p-sss - Use AES_BLOCK_SIZE define instead of number
crypto: stm32 - drop pointless static qualifier in stm32_hash_remove()
crypto: chelsio - Fixed Traffic Stall
crypto: marvell - Remove set but not used variable 'ivsize'
crypto: ccp - Update driver messages to remove some confusion
crypto: adiantum - add 1536 and 4096-byte test vectors
crypto: nhpoly1305 - add a test vector with len % 16 != 0
crypto: arm/aes-ce - update IV after partial final CTR block
...
- Add compatibility support for different FWs in the hisi LPC bus driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=f0/p
-----END PGP SIGNATURE-----
Merge tag 'hisi-drivers-for-5.1' of git://github.com/hisilicon/linux-hisi into arm/drivers
ARM64: hisi: SoC driver updates for 5.1
- Add compatibility support for different FWs in the hisi LPC bus driver
* tag 'hisi-drivers-for-5.1' of git://github.com/hisilicon/linux-hisi:
bus: hisi_lpc: Don't fail probe for unrecognised child devices
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Do not get GPCv2 driver depend on SOC_IMX8MQ since the driver is
going to be used on more SoCs than just i.MX8MQ.
- Add power domain information into SCU bindings document.
- Add support of start/stop a CPU into imx firmware driver.
- Support multiple address ranges per child node for imx-weim bus
driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcYi+0AAoJEFBXWFqHsHzOtdYH/jX/y0r7OvX5GVSrrnW8PlkC
3i2EQ0sGOxWOMqBegZIpFe9W7IddAetMf6praPGz/efHPnoVC4jO8Yqe4TZwQXLB
vOxoN4G7NH9Al9RX11ce96kd/tUgVK/JHuQJ9fu+ogrprLpAS3w1sbIkidOMSF3M
/5VrmFCxUNOPwTHRnyjw8QsyypKnKEBu0jA8sgyUmg99ii6rqQ5OKh1vgKf62J0f
1BbJLalI0CxGcYVQxYBy2ML37+XxCcN9Vl8FxiI4tVRtZox8/YkU9V5vEgVWN2fS
ZWfgT9w7cJxI5x8Em8Cxe4zcyVdbn5w26lXc6WbXazIncm206Ps+DIeHkQI9jPA=
=8C2m
-----END PGP SIGNATURE-----
Merge tag 'imx-drivers-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers
i.MX drivers update for 5.1:
- Do not get GPCv2 driver depend on SOC_IMX8MQ since the driver is
going to be used on more SoCs than just i.MX8MQ.
- Add power domain information into SCU bindings document.
- Add support of start/stop a CPU into imx firmware driver.
- Support multiple address ranges per child node for imx-weim bus
driver.
* tag 'imx-drivers-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
firmware: imx: Add support to start/stop a CPU
soc: imx: Break dependency on SOC_IMX8MQ for GPCv2
firmware: imx: scu-pd: add fallback compatible string support
dt-bindings: fsl: scu: add imx8qm scu power domain support
dt-bindings: fsl: scu: add fallback compatible string for power domain
bus: imx-weim: guard against timing configuration conflicts
bus: imx-weim: support multiple address ranges per child node
dt-bindings: bus: imx-weim: document multiple address ranges per child node
soc: imx: gpcv2: handle reset clocks
soc: imx: gpcv2: handle additional power-down bits in handshake register
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently for ACPI-based FW we fail the probe for an unrecognised child
HID.
However, there is FW in the field with LPC child devices having fake HIDs,
namely "IPI0002", which was an IPMI device invented to support the
initial out-of-tree LPC host driver, different from the final mainline
version.
To provide compatibility support for these dodgy FWs, just discard the
unrecognised HIDs instead of failing the probe altogether.
Tested-by: Zengruan Ye <yezengruan@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Commit 84badc5ec5 ("ARM: dts: omap4: Move l4 child devices to probe
them with ti-sysc") started producing a warning for pwm-omap-dmtimer:
WARNING: CPU: 0 PID: 77 at drivers/bus/omap_l3_noc.c:147
l3_interrupt_handler+0x2f8/0x388
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4PER2 (Idle):
Data Access in Supervisor mode during Functional access
...
__pm_runtime_idle
omap_dm_timer_disable
pwm_omap_dmtimer_start
pwm_omap_dmtimer_enable
pwm_apply_state
pwm_vibrator_start
pwm_vibrator_play_work
This is because the timer that pwm-omap-dmtimer is using is now being
probed with ti-sysc interconnect target module instead of omap_device
and the ti-sysc quirk for SYSC_QUIRK_LEGACY_IDLE is not fully
compatible with what omap_device has been doing.
We could fix this by reverting the timer changes and have the timer
probe again with omap_device. Or we could add more quirk handling to
ti-sysc driver. But as these options don't work nicely as longer term
solutions, let's just make timers probe with ti-sysc without any
quirks.
To do this, all we need to do is remove quirks for timers for ti-sysc,
and drop the bogus pm_runtime_irq_safe() flag for timer-ti-dm.
We should not use pm_runtime_irq_safe() anyways for drivers as it will
take a permanent use count on the parent device blocking the parent
devices from idling and has been forcing ti-sysc driver to use a
quirk flag.
Note that we will move the timer data to DEBUG section later on in
clean-up patches.
Fixes: 84badc5ec5 ("ARM: dts: omap4: Move l4 child devices to probe them with ti-sysc")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-By: Andreas Kemnade <andreas@kemnade.info>
Tested-By: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allocatable devices can be acquired by drivers on the fsl-mc bus using
the fsl_mc_portal_allocate or fsl_mc_object_allocate functions. Add a
device link between the consumer device and the supplier device so that
proper resource management is achieved.
Also, adding a link between these devices ensures that a proper unbind
order is respected (ie before the supplier device is unbound from its
respective driver all consumer devices will be notified and unbound
first).
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
When specifying weim child devices, there is a risk that more than
one timing setting is specified for the same chip select.
The driver cannot support such a configuration.
In case of conflict, this patch will print a warning to the log,
and will ignore the child node in question.
In this example, node acme@1 will be ignored, as it tries to modify
timing settings for CS0:
&weim {
acme@0 {
compatible = "acme,whatever";
reg = <0 0 0x100>;
fsl,weim-cs-timing = <something>;
};
acme@1 {
compatible = "acme,whatnot";
reg = <0 0x500 0x100>;
fsl,weim-cs-timing = <something else>;
};
};
However in this example, the driver will be happy:
&weim {
acme@0 {
compatible = "acme,whatever";
reg = <0 0 0x100>;
fsl,weim-cs-timing = <something>;
};
acme@1 {
compatible = "acme,whatnot";
reg = <0 0x500 0x100>;
fsl,weim-cs-timing = <something>;
};
};
Signed-off-by: Sven Van Asbroeck <TheSven73@googlemail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ensure that timing values for the child node are applied to
all chip selects in the child's address ranges.
Note that this does not support multiple timing settings per
child; this can be added in the future if required.
Example:
&weim {
acme@0 {
compatible = "acme,whatever";
reg = <0 0 0x100>, <0 0x400000 0x800>,
<1 0x400000 0x800>;
fsl,weim-cs-timing = <0x024400b1 0x00001010 0x20081100
0x00000000 0xa0000240 0x00000000>;
};
};
Signed-off-by: Sven Van Asbroeck <TheSven73@googlemail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Misc driver updates for platforms, many of them power related.
- Rockchip adds power domain support for rk3066 and rk3188
- Amlogic adds a power measurement driver
- Allwinner adds SRAM support for three platforms (F1C100, H5, A64 C1)
- Wakeup and ti-sysc (platform bus) fixes for OMAP/DRA7
- Broadcom fixes suspend/resume with Thumb2 kernels, and improves
stability of a handful of firmware/platform interfaces
- PXA completes their conversion to dmaengine framework
- Renesas does a bunch of PM cleanups across many platforms
- Tegra adds support for suspend/resume on T186/T194, which includes
some driver cleanups and addition of wake events
- Tegra also adds a driver for memory controller (EMC) on Tegra2
- i.MX tweaks power domain bindings, and adds support for i.MX8MQ in GPC
- Atmel adds identifiers and LPDDR2 support for a new SoC, SAM9X60
+ misc cleanups across several platforms
-----BEGIN PGP SIGNATURE-----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=yEX2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Misc driver updates for platforms, many of them power related.
- Rockchip adds power domain support for rk3066 and rk3188
- Amlogic adds a power measurement driver
- Allwinner adds SRAM support for three platforms (F1C100, H5, A64
C1)
- Wakeup and ti-sysc (platform bus) fixes for OMAP/DRA7
- Broadcom fixes suspend/resume with Thumb2 kernels, and improves
stability of a handful of firmware/platform interfaces
- PXA completes their conversion to dmaengine framework
- Renesas does a bunch of PM cleanups across many platforms
- Tegra adds support for suspend/resume on T186/T194, which includes
some driver cleanups and addition of wake events
- Tegra also adds a driver for memory controller (EMC) on Tegra2
- i.MX tweaks power domain bindings, and adds support for i.MX8MQ in
GPC
- Atmel adds identifiers and LPDDR2 support for a new SoC, SAM9X60
and misc cleanups across several platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: at91: add support in soc driver for new SAM9X60
ARM: at91: add support in soc driver for LPDDR2 SiP
memory: omap-gpmc: Use of_node_name_eq for node name comparisons
bus: ti-sysc: Check for no-reset and no-idle flags at the child level
ARM: OMAP2+: Check also the first dts child for hwmod flags
soc: amlogic: meson-clk-measure: Add missing REGMAP_MMIO dependency
soc: imx: gpc: Increase GPC_CLK_MAX to 7
soc: renesas: rcar-sysc: Fix power domain control after system resume
soc: renesas: rcar-sysc: Merge PM Domain registration and linking
soc: renesas: rcar-sysc: Remove rcar_sysc_power_{down,up}() helpers
soc: renesas: r8a77990-sysc: Fix initialization order of 3DG-{A,B}
dt-bindings: sram: sunxi: Add compatible for the A64 SRAM C1
dt-bindings: sram: sunxi: Add bindings for the H5 with SRAM C1
dt-bindings: sram: Add Allwinner suniv F1C100s
soc: sunxi: sram: Add support for the H5 SoC system control
soc: sunxi: sram: Enable EMAC clock access for H3 variant
soc: imx: gpcv2: add support for i.MX8MQ SoC
soc: imx: gpcv2: move register access table to domain data
soc: imx: gpcv2: prefix i.MX7 specific defines
dmaengine: pxa: make the filter function internal
...
This series of changes improves the TI module flag handling to allow
booting with older dts files until the module flags have been moved
to the interconnect target module level. And there's a of_node_name_eq()
clean-up patch from Rob Herring for the GPMC driver.
-----BEGIN PGP SIGNATURE-----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=xcO5
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.21/driver-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
Few more omap driver fixes and improvments for v4.21 merge window
This series of changes improves the TI module flag handling to allow
booting with older dts files until the module flags have been moved
to the interconnect target module level. And there's a of_node_name_eq()
clean-up patch from Rob Herring for the GPMC driver.
* tag 'omap-for-v4.21/driver-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
memory: omap-gpmc: Use of_node_name_eq for node name comparisons
bus: ti-sysc: Check for no-reset and no-idle flags at the child level
ARM: OMAP2+: Check also the first dts child for hwmod flags
Signed-off-by: Olof Johansson <olof@lixom.net>
With ti-sysc, we need to now have the device tree properties for
ti,no-reset-on-init and ti,no-idle-on-init at the module level instead
of the child device level.
Let's check for these properties at the child device level to enable
quirks, and warn about moving the properties to the module level.
Otherwise am335x-evm based boards tagging gpio1 with ti,no-reset-on-init
will have their DDR power disabled if wired up in such a tricky way.
Note that this should not be an issue for earlier kernels as we don't
rely on this until the dts files have been updated to probe with ti-sysc
interconnect target driver.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
for 4.21, please pull the following changes:
- James fixes the firmware interface after a commit changed the use of
VLA and broke large transfers
- Stefan adds a timeout check for Raspberry Pi firmware transactions and
updates a bunch of SoC/firmware files to use SPDX tags
- Wolfram switches the GISB bus arbiter to use dev_get_drvdata()
- Yangtao provides a fix for a reference leak due to a call to
of_find_node_by_path()
- Florian fixes the CPU re-entry point out of S3 suspend with kernels
built in Thumb2 mode
-----BEGIN PGP SIGNATURE-----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=yGiB
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.21/drivers' of https://github.com/Broadcom/stblinux into next/drivers
This pull request contains Broadcom ARM/ARM64/MIPS SoCs drivers changes
for 4.21, please pull the following changes:
- James fixes the firmware interface after a commit changed the use of
VLA and broke large transfers
- Stefan adds a timeout check for Raspberry Pi firmware transactions and
updates a bunch of SoC/firmware files to use SPDX tags
- Wolfram switches the GISB bus arbiter to use dev_get_drvdata()
- Yangtao provides a fix for a reference leak due to a call to
of_find_node_by_path()
- Florian fixes the CPU re-entry point out of S3 suspend with kernels
built in Thumb2 mode
* tag 'arm-soc/for-4.21/drivers' of https://github.com/Broadcom/stblinux:
soc: bcm: brcmstb: Don't leak device tree node reference
firmware: raspberrypi: Switch to SPDX identifier
firmware: raspberrypi: Fix firmware calls with large buffers
soc: bcm: Switch raspberrypi-power to SPDX identifier
firmware: raspberrypi: Define timeout for transactions
bus: brcmstb_gisb: simplify getting .driver_data
soc: bcm: brcmstb: Fix re-entry point with a THUMB2_KERNEL
Signed-off-by: Olof Johansson <olof@lixom.net>
We have OPT_CLKS_NEEDED in legacy platform data, but it's missing
from the ti-sysc driver for device tree based configuration.
In order to pass OPT_CLKS_NEEDED quirk flag we need to update omap4 module
data and add a new compatible for dra7 as the module layout is different
from sysc_regbits_omap4_mcasp.
Fixes: 70a65240ef ("bus: ti-sysc: Add register bits for interconnect
target modules")
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can have holes in clock_roles with interface clock missing for
example. Currently getting an optional clock will fail if there are
only a functional clock and an optional clock.
Fixes: 09dfe58107 ("bus: ti-sysc: Add handling for clkctrl opt clocks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The most noteworthy SoC driver changes this time include:
- The TEE subsystem gains an in-kernel interface to access the TEE
from device drivers.
- The reset controller subsystem gains a driver for the Qualcomm
Snapdragon 845 Power Domain Controller.
- The Xilinx Zynq platform now has a firmware interface for its
platform management unit. This contains a firmware "ioctl" interface
that was a little controversial at first, but the version we merged
solved that by not exposing arbitrary firmware calls to user space.
- The Amlogic Meson platform gains a "canvas" driver that is used
for video processing and shared between different high-level drivers.
The rest is more of the usual, mostly related to SoC specific power
management support and core drivers in drivers/soc:
- Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new
features related to power and reset control.
- The Mediatek mt8183 and mt6765 SoC platforms gain support for
their respective power management chips.
- A new driver for NXP i.MX8, which need a firmware interface for
power management.
- The SCPI firmware interface now contains support estimating power
usage of performance states
- The NVIDIA Tegra "pmc" driver gains a few new features, in particular
a pinctrl interface for configuring the pads.
- Lots of small changes for Qualcomm, in particular the "smem"
device driver.
- Some cleanups for the TI OMAP series related to their sysc
controller.
Additional cleanups and bugfixes in SoC specific drivers include the
Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=c/PQ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The most noteworthy SoC driver changes this time include:
- The TEE subsystem gains an in-kernel interface to access the TEE
from device drivers.
- The reset controller subsystem gains a driver for the Qualcomm
Snapdragon 845 Power Domain Controller.
- The Xilinx Zynq platform now has a firmware interface for its
platform management unit. This contains a firmware "ioctl"
interface that was a little controversial at first, but the version
we merged solved that by not exposing arbitrary firmware calls to
user space.
- The Amlogic Meson platform gains a "canvas" driver that is used for
video processing and shared between different high-level drivers.
The rest is more of the usual, mostly related to SoC specific power
management support and core drivers in drivers/soc:
- Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new
features related to power and reset control.
- The Mediatek mt8183 and mt6765 SoC platforms gain support for their
respective power management chips.
- A new driver for NXP i.MX8, which need a firmware interface for
power management.
- The SCPI firmware interface now contains support estimating power
usage of performance states
- The NVIDIA Tegra "pmc" driver gains a few new features, in
particular a pinctrl interface for configuring the pads.
- Lots of small changes for Qualcomm, in particular the "smem" device
driver.
- Some cleanups for the TI OMAP series related to their sysc
controller.
Additional cleanups and bugfixes in SoC specific drivers include the
Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (129 commits)
firmware: tegra: bpmp: Implement suspend/resume support
drivers: clk: Add ZynqMP clock driver
dt-bindings: clock: Add bindings for ZynqMP clock driver
firmware: xilinx: Add zynqmp IOCTL API for device control
Documentation: xilinx: Add documentation for eemi APIs
MAINTAINERS: imx: include drivers/firmware/imx path
firmware: imx: add misc svc support
firmware: imx: add SCU firmware driver support
reset: Fix potential use-after-free in __of_reset_control_get()
dt-bindings: arm: fsl: add scu binding doc
soc: fsl: qbman: add interrupt coalesce changing APIs
soc: fsl: bman_portals: defer probe after bman's probe
soc: fsl: qbman: Use last response to determine valid bit
soc: fsl: qbman: Add 64 bit DMA addressing requirement to QBMan
soc: fsl: qbman: replace CPU 0 with any online CPU in hotplug handlers
soc: fsl: qbman: Check if CPU is offline when initializing portals
reset: qcom: PDC Global (Power Domain Controller) reset controller
dt-bindings: reset: Add PDC Global binding for SDM845 SoCs
reset: Grammar s/more then once/more than once/
bus: ti-sysc: Just use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
...
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral bindings
out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers
-----BEGIN PGP SIGNATURE-----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=335v
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
"A bit bigger than normal as I've been busy this cycle.
There's a few things with dependencies and a few things subsystem
maintainers didn't pick up, so I'm taking them thru my tree.
The fixes from Johan didn't get into linux-next, but they've been
waiting for some time now and they are what's left of what subsystem
maintainers didn't pick up.
Summary:
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral
bindings out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers"
* tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (78 commits)
ARM: dt: relicense two DT binding IRQ headers
power: supply: twl4030-charger: fix OF sibling-node lookup
NFC: nfcmrvl_uart: fix OF child-node lookup
net: stmmac: dwmac-sun8i: fix OF child-node lookup
net: bcmgenet: fix OF child-node lookup
drm/msm: fix OF child-node lookup
drm/mediatek: fix OF sibling-node lookup
of: Add missing exports of node name compare functions
dt-bindings: Add OLPC vendor prefix
dt-bindings: misc: bk4: Add device tree binding for Liebherr's BK4 SPI bus
dt-bindings: thermal: samsung: Add SPDX license identifier
dt-bindings: clock: samsung: Add SPDX license identifiers
dt-bindings: timer: ostm: Add R7S9210 support
dt-bindings: phy: rcar-gen2: Add r8a7744 support
dt-bindings: can: rcar_can: Add r8a7744 support
dt-bindings: timer: renesas, cmt: Document r8a7744 CMT support
dt-bindings: watchdog: renesas-wdt: Document r8a7744 support
dt-bindings: thermal: rcar: Add device tree support for r8a7744
Documentation: dt: Add binding for /secure-chosen/stdout-path
dt-bindings: arm: zte: Move sysctrl bindings to their own doc
...
These updates bring:
- Debugfs support for the Intel VT-d driver. When enabled, it
now also exposes some of its internal data structures to
user-space for debugging purposes.
- ARM-SMMU driver now uses the generic deferred flushing
and fast-path iova allocation code. This is expected to be a
major performance improvement, as this allocation path scales
a lot better.
- Support for r8a7744 in the Renesas iommu driver
- Couple of minor fixes and improvements all over the place
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=q1HJ
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- Debugfs support for the Intel VT-d driver.
When enabled, it now also exposes some of its internal data
structures to user-space for debugging purposes.
- ARM-SMMU driver now uses the generic deferred flushing and fast-path
iova allocation code.
This is expected to be a major performance improvement, as this
allocation path scales a lot better.
- Support for r8a7744 in the Renesas iommu driver
- Couple of minor fixes and improvements all over the place
* tag 'iommu-updates-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (39 commits)
iommu/arm-smmu-v3: Remove unnecessary wrapper function
iommu/arm-smmu-v3: Add SPDX header
iommu/amd: Add default branch in amd_iommu_capable()
dt-bindings: iommu: ipmmu-vmsa: Add r8a7744 support
iommu/amd: Move iommu_init_pci() to .init section
iommu/arm-smmu: Support non-strict mode
iommu/io-pgtable-arm-v7s: Add support for non-strict mode
iommu/arm-smmu-v3: Add support for non-strict mode
iommu/io-pgtable-arm: Add support for non-strict mode
iommu: Add "iommu.strict" command line option
iommu/dma: Add support for non-strict mode
iommu/arm-smmu: Ensure that page-table updates are visible before TLBI
iommu/arm-smmu-v3: Implement flush_iotlb_all hook
iommu/arm-smmu-v3: Avoid back-to-back CMD_SYNC operations
iommu/arm-smmu-v3: Fix unexpected CMD_SYNC timeout
iommu/io-pgtable-arm: Fix race handling in split_blk_unmap()
iommu/arm-smmu-v3: Fix a couple of minor comment typos
iommu: Fix a typo
iommu: Remove .domain_{get,set}_windows
iommu: Tidy up window attributes
...
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO
lines as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can
use only the fastpatch callbacks to enable/disable irqs
like any normal irqchip, especially the gpiod_lock_as_irq()
has been improved to be callable in fastpath context.
A bunch of rework had to be done to achieve this but it is
a big win since I never liked to restrict this to slowpath.
The only call requireing slowpath was try_module_get() and
this is kept at the .request_resources() slowpath callback.
In the GPIO CEC driver this is a big win sine a single
line is used for both outgoing and incoming traffic, and
this needs to use IRQs for incoming traffic while actively
driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a
"cookie" (struct gpio_array) and a bitmap for setting or
getting multiple GPIO lines at once. This improvement
orginated in a specific need to speed up an OMAP1 driver and
has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot
of checks and code when we want things to go really fast.
The previous code would minimize the number of calls
down to the driver callbacks assuming the CPU speed was
orders of magnitude faster than the I/O latency, but this
assumption was wrong on several platforms: what we needed
to do was to profile and improve the speed on the hot
path of the array functions and this change is now
completed.
- Clean out the painful and hard to grasp BNF experiments
from the device tree bindings. Future approaches are looking
into using JSON schema for this purpose. (Rob Herring
is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and
other contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin
control driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver.
-----BEGIN PGP SIGNATURE-----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=YosT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
This series gets rid of the SYSC_QUIRK_RESOURCE_PROVIDER to make device
detection happen mostly only if #define DEBUG is set. Few core devices still
need to be detected to set legacy quirks.
We also add support for booting am335x, am437x and dra7 SoCs with L4 devices
defined in device tree instead of legacy platform data.
And finally we simplify suspend with just SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
and dropping the custom functions that were attempting to work around
issues that really turned out to be child device driver related issues.
Apologies for a late pull request, debugging the suspend issues took a while
and I did not want to send these changes until that got sorted out.
-----BEGIN PGP SIGNATURE-----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=f9xh
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.20/ti-sysc-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
TI sysc driver changes for v4.20 merge window
This series gets rid of the SYSC_QUIRK_RESOURCE_PROVIDER to make device
detection happen mostly only if #define DEBUG is set. Few core devices still
need to be detected to set legacy quirks.
We also add support for booting am335x, am437x and dra7 SoCs with L4 devices
defined in device tree instead of legacy platform data.
And finally we simplify suspend with just SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
and dropping the custom functions that were attempting to work around
issues that really turned out to be child device driver related issues.
Apologies for a late pull request, debugging the suspend issues took a while
and I did not want to send these changes until that got sorted out.
* tag 'omap-for-v4.20/ti-sysc-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Just use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
bus: ti-sysc: Make some warnings debug only
bus: ti-sysc: Detect devices for debug on dra7
bus: ti-sysc: Detect timer and gpio on dra7
bus: ti-sysc: Detect devices on am335x when DEBUG is enabled
bus: ti-sysc: Detect more devices on am473x for debugging
bus: ti-sysc: Update revision masks to support am437x
bus: ti-sysc: Defer suspend as needed
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As Grygorii Strashko pointed out, the runtime PM use count of the
children can be whatever at suspend and we should not use it. So
let's just suspend ti-sysc at noirq level and get rid of some code.
Let's also remove the PM_SLEEP ifdef and use __maybe_unused as the
PM code already deals with the ifdefs.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Checking the child node names is pointless as the DT node name can
never be NULL, so remove it.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We're currently warning about busy children on suspend in
sysc_child_suspend_noirq() but the legacy code omap_device does
not do that. Let's just make it dev_dbg() instead of dev_warn().
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to detect timer and gpio on dra7 because of the
SYSC_QUIRK_LEGACY_IDLE flag for suspend and resume.
Signed-off-by: Tony Lindgren <tony@atomide.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Signed-off-by: Rob Herring <robh@kernel.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Stuart Yoder <stuyoder@gmail.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
of_dma_configure() API expects coherent_dma_mask to be correctly
set in the devices. This patch does the needful.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch adds support of dma configuration for devices on fsl-mc
bus using 'dma_configure' callback for busses. Also, directly calling
arch_setup_dma_ops is removed from the fsl-mc bus.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When debug is enabled, we want to see what devices we're detecting
to make things a bit easier for us. Many of these devices will also
be available on am335x and dra7, and some just need updating the
revision register mask.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to detect few new devices to tag for noirq_suspend and
pm_runtime_irq_safe to avoid causing regressions compared to
legacy platform data booting.
Let's update i2c, gpio, uart and wdt revision masks to detect
them on am437x. Note that we can remove the second wdt entry
with the updated mask. Note that we also have some uarts with
a different revision register.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't care when we suspend but some our children do. In order to
avoid tagging various modules with SYSC_QUIRK_RESOURCE_PROVIDER, let's
do it automatically by tagging modules that are busy on suspend for
noirq suspend. This way we can just do module detection on define DEBUG.
Note that we still need to keep SYSC_QUIRK_LEGACY_IDLE flag around so
the our legacy single-child devices that set pm_runtime_irq_safe() can
manage the interconnect target module themselves.
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to make use of array info obtained from gpiod_get_array() and
speed up processing of arrays matching single GPIO chip layout, that
information must be passed to get/set array functions. Extend the
functions' API with that additional parameter and update all users.
Pass NULL if a user builds an array itself from single GPIOs.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most users of get/set array functions iterate consecutive bits of data,
usually a single integer, while processing array of results obtained
from, or building an array of values to be passed to those functions.
Save time wasted on those iterations by changing the functions' API to
accept bitmaps.
All current users are updated as well.
More benefits from the change are expected as soon as planned support
for accepting/passing those bitmaps directly from/to respective GPIO
chip callbacks if applicable is implemented.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC
-----BEGIN PGP SIGNATURE-----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=ZjwY
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits)
drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests
soc: fsl: cleanup Kconfig menu
soc: fsl: dpio: Convert DPIO documentation to .rst
staging: fsl-mc: Remove remaining files
staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl
staging: fsl-dpaa2: eth: move generic FD defines to DPIO
soc: fsl: qe: gpio: Add qe_gpio_set_multiple
usb: host: exynos: Remove support for Exynos5440
clk: samsung: Remove support for Exynos5440
soc: sunxi: Add the A13, A23 and H3 system control compatibles
reset: uniphier: add reset control support for SPI
cpufreq: exynos: Remove support for Exynos5440
ata: ahci-platform: Remove support for Exynos5440
soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata
soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs
soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs
soc: mediatek: pwrap: fix cipher init setting error
dt-bindings: pwrap: mediatek: add pwrap support for MT6797
reset: uniphier: add USB3 core reset control
dt-bindings: reset: uniphier: add USB3 core reset support
...
If no_console_suspend is set, we should keep console enabled during suspend.
Lets fix this by only producing a warning if we can't idle hardware during
suspend.
Fixes: ef55f8215a ("bus: ti-sysc: Improve suspend and resume handling")
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can have the interconnect target module control registers pretty
much anywhere within the module range. The current code attempts an
incomplete optimization of the ioremap size but does it wrong and
it only works for registers at the beginning of the module.
Let's just use the largest control register to calculate the ioremap
size. The ioremapped range is for most part cached anyways so there
is no need for size optimization. Let's also update the comments
accordingly.
Fixes: 0eecc636e5 ("bus: ti-sysc: Add minimal TI sysc interconnect
target driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
In the quest to remove all stack VLA usage from the kernel[1], this
switches to using a maximum size and adds a sanity check.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
There's been work for this release cycles in both the SRAM controller
driver in order to support more SoCs, as part of our VPU work, but also to
enable the EMAC on the A64 (that needs to poke at registers within the same
register space).
Some work has been needed too to represent the bus to the display engine
controllers that all need an SRAM to be mapped to the CPU to be able to
access those controllers' registers.
-----BEGIN PGP SIGNATURE-----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=NuX/
-----END PGP SIGNATURE-----
Merge tag 'sunxi-drivers-for-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/drivers
Allwinner drivers changes for 4.19
There's been work for this release cycles in both the SRAM controller
driver in order to support more SoCs, as part of our VPU work, but also to
enable the EMAC on the A64 (that needs to poke at registers within the same
register space).
Some work has been needed too to represent the bus to the display engine
controllers that all need an SRAM to be mapped to the CPU to be able to
access those controllers' registers.
* tag 'sunxi-drivers-for-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
soc: sunxi: Add the A13, A23 and H3 system control compatibles
drivers: soc: sunxi: Add support for the C1 SRAM region
dt-bindings: sram: sunxi: Populate valid sections compatibles
dt-bindings: sram: sunxi: Add A13, A20, A23 and H3 dedicated bindings
soc: sunxi: sram: Add dt match for the A10 system-control compatible
dt-bindings: sram: sunxi: Introduce new A10 binding for system-control
bus: add bus driver for accessing Allwinner A64 DE2
dt-bindings: add binding for the Allwinner A64 DE2 bus
soc: sunxi: sram: Add updated compatible string for A64 system control
dt-bindings: sram: Rename A64 SRAM controller compatible
soc: sunxi: export a regmap for EMAC clock reg on A64
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for the software reset of a target interconnect
module using its sysconfig and sysstatus registers.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
[tony@atomide.com: updated to check if sysconfig exists]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The dra76x MCAN generic interconnect module has a its own
format for the bits in the control registers.
Therefore add a new module type, new regbits and new capabilities
specific to the MCAN module.
Acked-by: Rob Herring <robh@kernel.org>
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adjusts the allocator calls to use 2-factor argument call style, as
done treewide already for improved defense against allocation overflows.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The "Display Engine 2.0" (usually called DE2) on the Allwinner A64 SoC
is different from the ones on other Allwinner SoCs. It requires a SRAM
region to be claimed, otherwise all DE2 subblocks won't be accessible.
Add a bus driver for the Allwinner A64 DE2 part which claims the SRAM
region when probing.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=zUUp
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull more overflow updates from Kees Cook:
"The rest of the overflow changes for v4.18-rc1.
This includes the explicit overflow fixes from Silvio, further
struct_size() conversions from Matthew, and a bug fix from Dan.
But the bulk of it is the treewide conversions to use either the
2-factor argument allocators (e.g. kmalloc(a * b, ...) into
kmalloc_array(a, b, ...) or the array_size() macros (e.g. vmalloc(a *
b) into vmalloc(array_size(a, b)).
Coccinelle was fighting me on several fronts, so I've done a bunch of
manual whitespace updates in the patches as well.
Summary:
- Error path bug fix for overflow tests (Dan)
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed
(Kees)"
* tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (26 commits)
treewide: Use array_size in f2fs_kvzalloc()
treewide: Use array_size() in f2fs_kzalloc()
treewide: Use array_size() in f2fs_kmalloc()
treewide: Use array_size() in sock_kmalloc()
treewide: Use array_size() in kvzalloc_node()
treewide: Use array_size() in vzalloc_node()
treewide: Use array_size() in vzalloc()
treewide: Use array_size() in vmalloc()
treewide: devm_kzalloc() -> devm_kcalloc()
treewide: devm_kmalloc() -> devm_kmalloc_array()
treewide: kvzalloc() -> kvcalloc()
treewide: kvmalloc() -> kvmalloc_array()
treewide: kzalloc_node() -> kcalloc_node()
treewide: kzalloc() -> kcalloc()
treewide: kmalloc() -> kmalloc_array()
mm: Introduce kvcalloc()
video: uvesafb: Fix integer overflow in allocation
UBIFS: Fix potential integer overflow in allocation
leds: Use struct_size() in allocation
Convert intel uncore to struct_size
...
This branch contains platform-related driver updates for ARM and ARM64.
Highlights:
- ARM SCMI (System Control & Management Interface) driver cleanups
- Hisilicon support for LPC bus w/ ACPI
- Reset driver updates for several platforms: Uniphier,
- Rockchip power domain bindings and hardware descriptions for several SoCs.
- Tegra memory controller reset improvements
-----BEGIN PGP SIGNATURE-----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=xs+f
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"This contains platform-related driver updates for ARM and ARM64.
Highlights:
- ARM SCMI (System Control & Management Interface) driver cleanups
- Hisilicon support for LPC bus w/ ACPI
- Reset driver updates for several platforms: Uniphier,
- Rockchip power domain bindings and hardware descriptions for
several SoCs.
- Tegra memory controller reset improvements"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (59 commits)
ARM: tegra: fix compile-testing PCI host driver
soc: rockchip: power-domain: add power domain support for px30
dt-bindings: power: add binding for px30 power domains
dt-bindings: power: add PX30 SoCs header for power-domain
soc: rockchip: power-domain: add power domain support for rk3228
dt-bindings: power: add binding for rk3228 power domains
dt-bindings: power: add RK3228 SoCs header for power-domain
soc: rockchip: power-domain: add power domain support for rk3128
dt-bindings: power: add binding for rk3128 power domains
dt-bindings: power: add RK3128 SoCs header for power-domain
soc: rockchip: power-domain: add power domain support for rk3036
dt-bindings: power: add binding for rk3036 power domains
dt-bindings: power: add RK3036 SoCs header for power-domain
dt-bindings: memory: tegra: Remove Tegra114 SATA and AFI reset definitions
memory: tegra: Remove Tegra114 SATA and AFI reset definitions
memory: tegra: Register SMMU after MC driver became ready
soc: mediatek: remove unneeded semicolon
soc: mediatek: add a fixed wait for SRAM stable
soc: mediatek: introduce a CAPS flag for scp_domain_data
soc: mediatek: reuse regmap_read_poll_timeout helpers
...
Here are the main updates for SoC support (besides DT additions) for ARM
32- and 64-bit platforms. The branch also contains defconfig updates to
turn on drivers and options as needed on the various platforms.
The largest parts of the delta are from cleanups moving platform data
and board file setup of TI platforms to ti-sysc bus drivers. There are
also some sweeping changes of eeprom and nand setup on Davinci, i.MX
and other platforms.
Samsung is removing support for Exynos5440, which was an oddball SoC
that hasn't been seen much use in designs.
Renesas is adding support for new SoCs (R-Car E3, RZ/G1C and RZ/N1D).
Linus Walleij is also removing support for ux500 (Sony Ericsson)
U8540/9540 SoCs that never made it to significant mass production and
products.
-----BEGIN PGP SIGNATURE-----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=S5wc
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"Here are the main updates for SoC support (besides DT additions) for
ARM 32- and 64-bit platforms. The branch also contains defconfig
updates to turn on drivers and options as needed on the various
platforms.
The largest parts of the delta are from cleanups moving platform data
and board file setup of TI platforms to ti-sysc bus drivers. There are
also some sweeping changes of eeprom and nand setup on Davinci, i.MX
and other platforms.
Samsung is removing support for Exynos5440, which was an oddball SoC
that hasn't been seen much use in designs.
Renesas is adding support for new SoCs (R-Car E3, RZ/G1C and RZ/N1D).
Linus Walleij is also removing support for ux500 (Sony Ericsson)
U8540/9540 SoCs that never made it to significant mass production and
products"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
MAINTAINERS: add NXP linux team maillist as i.MX reviewer
ARM: stm32: Don't select DMA unconditionally on STM32MP157C
arm64: defconfig: Enable PCIe on msm8996 and db820c
ARM: pxa3xx: enable external wakeup pins
ARM: pxa: stargate2: use device properties for at24 eeprom
arm64: defconfig: Enable HISILICON_LPC
arm64: defconfig: enable drivers for Poplar support
arm64: defconfig: Enable UFS on msm8996
ARM: berlin: switch to SPDX license identifier
arm: berlin: remove non-necessary flush_cache_all()
ARM: berlin: extend BG2CD Kconfig entry
OMAP: CLK: CLKSRC: Add suspend resume hooks
ARM: AM43XX: Add functions to save/restore am43xx control registers
ASoC: ams_delta: use GPIO lookup table
ARM: OMAP1: ams-delta: add GPIO lookup tables
bus: ti-sysc: Fix optional clocks array access
ARM: OMAP2+: Make sure LOGICRETSTATE bits are not cleared
ARM: OMAP2+: prm44xx: Inroduce cpu_pm notifiers for context save/restore
ARM: OMAP2+: prm44xx: Introduce context save/restore for am43 PRCM IO
ARM: OMAP2+: powerdomain: Introduce cpu_pm notifiers for context save/restore
...
This fixes an array access errors if there are more optional clocks
than one.
-----BEGIN PGP SIGNATURE-----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=ZBeC
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.18/ti-sysc-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
One ti-sysc fix for v4.18 merge window
This fixes an array access errors if there are more optional clocks
than one.
* tag 'omap-for-v4.18/ti-sysc-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix optional clocks array access
Signed-off-by: Olof Johansson <olof@lixom.net>
We should be checking ddata->clocks[i] instead of clock_names[i]
for the optional clocks. Currently this just happens to work for
the typical case of one fck and one optional clock.
Fixes: 09dfe58107 ("bus: ti-sysc: Add handling for clkctrl opt clocks")
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Update hisi LPC bus driver to use the platform driver APIs
other than the MFD APIs to support connected device like UART
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=V8Bq
-----END PGP SIGNATURE-----
Merge tag 'hisi-drivers-for-4.18' of git://github.com/hisilicon/linux-hisi into next/drivers
ARM64: hisi: SoC driver updates for 4.18
- Update hisi LPC bus driver to use the platform driver APIs
other than the MFD APIs to support connected device like UART
* tag 'hisi-drivers-for-4.18' of git://github.com/hisilicon/linux-hisi:
HISI LPC: Add ACPI UART support
HISI LPC: Re-Add ACPI child enumeration support
HISI LPC: Stop using MFD APIs
Signed-off-by: Olof Johansson <olof@lixom.net>
Mixing asm and C code is not recommended in a naked function by
gcc and leads to an error when using clang:
drivers/bus/arm-cci.c:2107:2: error: non-ASM statement in naked
function is not supported
unreachable();
^
While the function is marked __naked it actually properly return
in asm. There is no need for the unreachable() call.
GCC 7.2 generates identical object files before and after, other
than (for obvious reasons) the line numbers generated by
WANT_WARN_ON_SLOWPATH for all the WARN()s appearing later in the
file.
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This series improves the ti-sysc interconnect target module driver to
the point where a most of SoC can be booted with interconnect target
module data configured in device tree instead of legacy platform data.
The related device tree changes need some more work though, and can
wait for v4.19. Also some drivers using nested interconnects like DSS
need more work.
We can now remove the unused pm-noop code that is not doing anything
any longer. And we can now initialize things for PM and display pdata
later to prepare things for using ti-sysc driver.
We also need to add some more quirk handling so we can boot both with
platform data and dts data.
-----BEGIN PGP SIGNATURE-----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=jYZ6
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.18/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
ti-sysc driver related changes for omap variants
This series improves the ti-sysc interconnect target module driver to
the point where a most of SoC can be booted with interconnect target
module data configured in device tree instead of legacy platform data.
The related device tree changes need some more work though, and can
wait for v4.19. Also some drivers using nested interconnects like DSS
need more work.
We can now remove the unused pm-noop code that is not doing anything
any longer. And we can now initialize things for PM and display pdata
later to prepare things for using ti-sysc driver.
We also need to add some more quirk handling so we can boot both with
platform data and dts data.
* tag 'omap-for-v4.18/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Show module information for suspend if DEBUG is enabled
bus: ti-sysc: Tag sdio and wdt with legacy mode for suspend
bus: ti-sysc: Detect UARTs for SYSC_QUIRK_LEGACY_IDLE quirk on omap4
bus: ti-sysc: Detect omap4 type timers for quirk
bus: ti-sysc: Add initial support for external resets
bus: ti-sysc: Improve suspend and resume handling
bus: ti-sysc: Tag some modules resource providers for noirq suspend
bus: ti-sysc: Add handling for clkctrl opt clocks
bus: ti-sysc: Make child clock alias handling more generic
bus: ti-sysc: Handle simple-bus for nested children
ARM: OMAP2+: Make display related init into device_initcall
ARM: OMAP2+: Initialize SoC PM later
ARM: OMAP2+: Only probe SDMA via ti-sysc if configured in dts
ARM: OMAP2+: Use signed value for sysc register offsets
ARM: OMAP2+: Allow using ti-sysc for system timers
ARM: OMAP2+: Drop unused pm-noop
Signed-off-by: Olof Johansson <olof@lixom.net>
Nobody would be insane enough to try and use level triggered
MSIs on PCI, but let's make sure it doesn't happen. Also,
let's mandate that the irqchip backing the platform MSI domain
is providing the IRQCHIP_SUPPORTS_LEVEL_MSI flag.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lkml.kernel.org/r/20180508121438.11301-3-marc.zyngier@arm.com
On the Huawei D03 development board the system UART is
the UART connected on the LPC bus.
The profile for the device driver required for this HW
is as follows:
- platform driver
- 16550
- ACPI support
- polling mode support
- IO space support
In principle we should use the PNP driver (8250_dw.c) for
8250-devices with ACPI FW. However since this driver does
not support PNP devices, and modifying the PNP core code
to support it is not worth the effort, use the generic
8250 isa driver.
For this, we setup the pdev platform data for the serial
8250 port.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Since we no longer use the MFD APIs to enumerate the
child devices on the bus, use the platform driver APIs
directly.
In this patch we iterate of the children devices for the
host, and create a platform device directly per child.
For the iterating, we match the child ACPI HID against a
known list of supported child devices and their respective
ACPIs HID, to find the device name and any other
supplementary data.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The MFD APIs should only be used by drivers in
drivers/mfd. It is not worth splitting the driver to have
separate parts in drivers/bus and drivers/mfd, so just
drop MFD API usage.
As a solution, we will use the platform device APIs directly
to achieve the same as we had when using MFD APIs.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Let's show module info if DEBUG is enabled to make it easier to follow
what happens on the suspend and resume path.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like these two device drivers don't yet behave properly for suspend
unless configured with the legacy option.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Starting with omap4, UARTs have different revision register that we need to
detect to enable SYSC_QUIRK_LEGACY_IDLE. Otherwise UARTs won't idle properly.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Starting with omap4 some timers have different sysc registers (type2) compared
to the omap2 timers (type1). We need to detect these to enable the quirk for
SYSC_QUIRK_LEGACY_IDLE, otherwise these won't be idling properly.
Siganed-off-by: Tony Lindgren <tony@atomide.com>
Some modules need to use external resets in the rstctrl bits. Typically
only one of the rstctrl bits is for the interconnect target module while
the others are for various child devices.
For ti-sysc driver, we just need the module rstctrl bit mapped. The rest
of the rstctrl bits can be directly mapped to the child devices.
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on testing with more devices I noticed that some devices
don't suspend or resume properly. We need to PM runtime suspend
and resume devices if we have ddata->needs_resume set.
Let's also improve the error handling and add few debug statements
to make it easier to notice suspend and resume related issues if
DEBUG is set.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Modules that provide resources for other modules need to be suspended
and resumed in the noirq calls. Tag the resource providing modules.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There can be up to eight optional device functional gate gate clocks for
each clkctrl instance in clkctrl register bits 8 to 15. Some of them are
only needed for module level reset while others may always be needed
during use. Let's add support for those and update the binding doc
accordingly.
Note that the optional clkctrl mux and divider clocks starting at bit 20
can be directly mapped to the child devices, and ti-sysc does not need to
manage those.
And as GPIOs need the optional clocks for reset, we can now add it with
SYSC_QUIRK_OPT_CLKS_IN_RESET.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to prepare supporting clkctrl optional clocks, we need to
make the current child clock handling more generic so we can use the
clock role names for the optional clocks in the following patch.
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise child devices that some interconnect target module devices
have won't probe using simple-bus.
Signed-off-by: Tony Lindgren <tony@atomide.com>
For ACPI support of the HiSilicon LPC driver we depend
on MFD_CORE config.
Currently the HiSi LPC Kconfig entry does not define this
dependency, so add it.
The reason for depending on MFD_CORE in the driver is
that we model the LPC host as an MFD, in that a platform
device will be created for each device on the bus.
We do this as we need to modify the resources of these
derived platform devices, something which we should not
do to the original devices created in the ACPI scan.
Details in e0aa1563f8 ("HISI LPC: Add ACPI support").
Fixes: e0aa1563f8 ("HISI LPC: Add ACPI support")
Reported-and-tested-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=T++R
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- move pci_uevent_ers() out of pci.h (Michael Ellerman)
- skip ASPM common clock warning if BIOS already configured it (Sinan
Kaya)
- fix ASPM Coverity warning about threshold_ns (Gustavo A. R. Silva)
- remove last user of pci_get_bus_and_slot() and the function itself
(Sinan Kaya)
- add decoding for 16 GT/s link speed (Jay Fang)
- add interfaces to get max link speed and width (Tal Gilboa)
- add pcie_bandwidth_capable() to compute max supported link bandwidth
(Tal Gilboa)
- add pcie_bandwidth_available() to compute bandwidth available to
device (Tal Gilboa)
- add pcie_print_link_status() to log link speed and whether it's
limited (Tal Gilboa)
- use PCI core interfaces to report when device performance may be
limited by its slot instead of doing it in each driver (Tal Gilboa)
- fix possible cpqphp NULL pointer dereference (Shawn Lin)
- rescan more of the hierarchy on ACPI hotplug to fix Thunderbolt/xHCI
hotplug (Mika Westerberg)
- add support for PCI I/O port space that's neither directly accessible
via CPU in/out instructions nor directly mapped into CPU physical
memory space. This is fairly intrusive and includes minor changes to
interfaces used for I/O space on most platforms (Zhichang Yuan, John
Garry)
- add support for HiSilicon Hip06/Hip07 LPC I/O space (Zhichang Yuan,
John Garry)
- use PCI_EXP_DEVCTL2_COMP_TIMEOUT in rapidio/tsi721 (Bjorn Helgaas)
- remove possible NULL pointer dereference in of_pci_bus_find_domain_nr()
(Shawn Lin)
- report quirk timings with dev_info (Bjorn Helgaas)
- report quirks that take longer than 10ms (Bjorn Helgaas)
- add and use Altera Vendor ID (Johannes Thumshirn)
- tidy Makefiles and comments (Bjorn Helgaas)
- don't set up INTx if MSI or MSI-X is enabled to align cris, frv,
ia64, and mn10300 with x86 (Bjorn Helgaas)
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
- use generic pci_mmap_resource_range() instead of powerpc and xtensa
arch-specific versions (David Woodhouse)
- support arbitrary PCI host bridge offsets on sparc (Yinghai Lu)
- remove System and Video ROM reservations on sparc (Bjorn Helgaas)
- probe for device reset support during enumeration instead of runtime
(Bjorn Helgaas)
- add ACS quirk for Ampere (née APM) root ports (Feng Kan)
- add function 1 DMA alias quirk for Marvell 88SE9220 (Thomas
Vincent-Cross)
- protect device restore with device lock (Sinan Kaya)
- handle failure of FLR gracefully (Sinan Kaya)
- handle CRS (config retry status) after device resets (Sinan Kaya)
- skip various config reads for SR-IOV VFs as an optimization
(KarimAllah Ahmed)
- consolidate VPD code in vpd.c (Bjorn Helgaas)
- add Tegra dependency on PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
- add DT support for R-Car r8a7743 (Biju Das)
- fix a PCI_EJECT vs PCI_BUS_RELATIONS race condition in Hyper-V host
bridge driver that causes a general protection fault (Dexuan Cui)
- fix Hyper-V host bridge hang in MSI setup on 1-vCPU VMs with SR-IOV
(Dexuan Cui)
- fix Hyper-V host bridge hang when ejecting a VF before setting up MSI
(Dexuan Cui)
- make several structures static (Fengguang Wu)
- increase number of MSI IRQs supported by Synopsys DesignWare bridges
from 32 to 256 (Gustavo Pimentel)
- implemented multiplexed IRQ domain API and remove obsolete MSI IRQ
API from DesignWare drivers (Gustavo Pimentel)
- add Tegra power management support (Manikanta Maddireddy)
- add Tegra loadable module support (Manikanta Maddireddy)
- handle 64-bit BARs correctly in endpoint support (Niklas Cassel)
- support optional regulator for HiSilicon STB (Shawn Guo)
- use regulator bulk API for Qualcomm apq8064 (Srinivas Kandagatla)
- support power supplies for Qualcomm msm8996 (Srinivas Kandagatla)
* tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (123 commits)
MAINTAINERS: Add John Garry as maintainer for HiSilicon LPC driver
HISI LPC: Add ACPI support
ACPI / scan: Do not enumerate Indirect IO host children
ACPI / scan: Rename acpi_is_serial_bus_slave() for more general use
HISI LPC: Support the LPC host on Hip06/Hip07 with DT bindings
of: Add missing I/O range exception for indirect-IO devices
PCI: Apply the new generic I/O management on PCI IO hosts
PCI: Add fwnode handler as input param of pci_register_io_range()
PCI: Remove __weak tag from pci_register_io_range()
MAINTAINERS: Add missing /drivers/pci/cadence directory entry
fm10k: Report PCIe link properties with pcie_print_link_status()
net/mlx5e: Use pcie_bandwidth_available() to compute bandwidth
net/mlx5: Report PCIe link properties with pcie_print_link_status()
net/mlx4_core: Report PCIe link properties with pcie_print_link_status()
PCI: Add pcie_print_link_status() to log link speed and whether it's limited
PCI: Add pcie_bandwidth_available() to compute bandwidth available to device
misc: pci_endpoint_test: Handle 64-bit BARs properly
PCI: designware-ep: Make dw_pcie_ep_reset_bar() handle 64-bit BARs properly
PCI: endpoint: Make sure that BAR_5 does not have 64-bit flag set when clearing
PCI: endpoint: Make epc->ops->clear_bar()/pci_epc_clear_bar() take struct *epf_bar
...
The main addition this time around is the new ARM "SCMI" framework,
which is the latest in a series of standards coming from ARM to do power
management in a platform independent way. This has been through many
review cycles, and it relies on a rather interesting way of using the
mailbox subsystem, but in the end I agreed that Sudeep's version was
the best we could do after all.
Other changes include:
- the ARM CCN driver is moved out of drivers/bus into drivers/perf,
which makes more sense. Similarly, the performance monitoring
portion of the CCI driver are moved the same way and cleaned up
a little more.
- a series of updates to the SCPI framework
- support for the Mediatek mt7623a SoC in drivers/soc
- support for additional NVIDIA Tegra hardware in drivers/soc
- a new reset driver for Socionext Uniphier
- lesser bug fixes in drivers/soc, drivers/tee, drivers/memory, and
drivers/firmware and drivers/reset across platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Pmsx
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The main addition this time around is the new ARM "SCMI" framework,
which is the latest in a series of standards coming from ARM to do
power management in a platform independent way.
This has been through many review cycles, and it relies on a rather
interesting way of using the mailbox subsystem, but in the end I
agreed that Sudeep's version was the best we could do after all.
Other changes include:
- the ARM CCN driver is moved out of drivers/bus into drivers/perf,
which makes more sense. Similarly, the performance monitoring
portion of the CCI driver are moved the same way and cleaned up a
little more.
- a series of updates to the SCPI framework
- support for the Mediatek mt7623a SoC in drivers/soc
- support for additional NVIDIA Tegra hardware in drivers/soc
- a new reset driver for Socionext Uniphier
- lesser bug fixes in drivers/soc, drivers/tee, drivers/memory, and
drivers/firmware and drivers/reset across platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (87 commits)
reset: uniphier: add ethernet reset control support for PXs3
reset: stm32mp1: Enable stm32mp1 reset driver
dt-bindings: reset: add STM32MP1 resets
reset: uniphier: add Pro4/Pro5/PXs2 audio systems reset control
reset: imx7: add 'depends on HAS_IOMEM' to fix unmet dependency
reset: modify the way reset lookup works for board files
reset: add support for non-DT systems
clk: scmi: use devm_of_clk_add_hw_provider() API and drop scmi_clocks_remove
firmware: arm_scmi: prevent accessing rate_discrete uninitialized
hwmon: (scmi) return -EINVAL when sensor information is unavailable
amlogic: meson-gx-socinfo: Update soc ids
soc/tegra: pmc: Use the new reset APIs to manage reset controllers
soc: mediatek: update power domain data of MT2712
dt-bindings: soc: update MT2712 power dt-bindings
cpufreq: scmi: add thermal dependency
soc: mediatek: fix the mistaken pointer accessed when subdomains are added
soc: mediatek: add SCPSYS power domain driver for MediaTek MT7623A SoC
soc: mediatek: avoid hardcoded value with bus_prot_mask
dt-bindings: soc: add header files required for MT7623A SCPSYS dt-binding
dt-bindings: soc: add SCPSYS binding for MT7623 and MT7623A SoC
...
This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips
in mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older
PXA and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure
is needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HD9V
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips in
mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older PXA
and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure is
needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (179 commits)
arm: npcm: modify configuration for the NPCM7xx BMC.
MAINTAINERS: update entry for ARM/berlin
ARM: omap2: fix am43xx build without L2X0
ARM: davinci: da8xx: simplify CFGCHIP regmap_config
ARM: davinci: da8xx: fix oops in USB PHY driver due to stack allocated platform_data
ARM: multi_v7_defconfig: add NXP FlexCAN IP support
ARM: multi_v7_defconfig: enable thermal driver for i.MX devices
ARM: multi_v7_defconfig: add RN5T618 PMIC family support
ARM: multi_v7_defconfig: add NXP graphics drivers
ARM: multi_v7_defconfig: add GPMI NAND controller support
ARM: multi_v7_defconfig: add OCOTP driver for NXP SoCs
ARM: multi_v7_defconfig: configure I2C driver built-in
arm64: defconfig: add CONFIG_UNIPHIER_THERMAL and CONFIG_SNI_AVE
ARM: imx: fix imx6sll-only build
ARM: imx: select ARM_CPU_SUSPEND for CPU_IDLE as well
ARM: mxs_defconfig: Re-sync defconfig
ARM: imx_v4_v5_defconfig: Use the generic fsl-asoc-card driver
ARM: imx_v4_v5_defconfig: Re-sync defconfig
arm64: defconfig: enable stmmac ethernet to defconfig
ARM: EXYNOS: Simplify code in coupled CPU idle hot path
...
Here is the big set of Staging/IIO driver patches for 4.17-rc1.
It is a lot, over 500 changes, but not huge by previous kernel release
standards. We deleted more lines than we added again (27k added vs. 91k
remvoed), thanks to finally being able to delete the IRDA drivers and
networking code.
We also deleted the ccree crypto driver, but that's coming back in
through the crypto tree to you, in a much cleaned-up form.
Added this round is at lot of "mt7621" device support, which is for an
embedded device that Neil Brown cares about, and of course a handful of
new IIO drivers as well.
And finally, the fsl-mc core code moved out of the staging tree to the
"real" part of the kernel, which is nice to see happen as well.
Full details are in the shortlog, which has all of the tiny cleanup
patches described.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsSnAA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn60ACgxKvU/5XBP14hBkBpAcD0Q43OHe0AniEti65M
Kw03GWK3NNM3pzk49BjZ
=sj3K
-----END PGP SIGNATURE-----
Merge tag 'staging-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here is the big set of Staging/IIO driver patches for 4.17-rc1.
It is a lot, over 500 changes, but not huge by previous kernel release
standards. We deleted more lines than we added again (27k added vs.
91k remvoed), thanks to finally being able to delete the IRDA drivers
and networking code.
We also deleted the ccree crypto driver, but that's coming back in
through the crypto tree to you, in a much cleaned-up form.
Added this round is at lot of "mt7621" device support, which is for an
embedded device that Neil Brown cares about, and of course a handful
of new IIO drivers as well.
And finally, the fsl-mc core code moved out of the staging tree to the
"real" part of the kernel, which is nice to see happen as well.
Full details are in the shortlog, which has all of the tiny cleanup
patches described.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (579 commits)
staging: rtl8723bs: Remove yield call, replace with cond_resched()
staging: rtl8723bs: Replace yield() call with cond_resched()
staging: rtl8723bs: Remove unecessary newlines from 'odm.h'.
staging: rtl8723bs: Rework 'struct _ODM_Phy_Status_Info_' coding style.
staging: rtl8723bs: Rework 'struct _ODM_Per_Pkt_Info_' coding style.
staging: rtl8723bs: Replace NULL pointer comparison with '!'.
staging: rtl8723bs: Factor out rtl8723bs_recv_tasklet() sections.
staging: rtl8723bs: Fix function signature that goes over 80 characters.
staging: rtl8723bs: Fix lines too long in update_recvframe_attrib().
staging: rtl8723bs: Remove unnecessary blank lines in 'rtl8723bs_recv.c'.
staging: rtl8723bs: Change camel case to snake case in 'rtl8723bs_recv.c'.
staging: rtl8723bs: Add missing braces in else statement.
staging: rtl8723bs: Add spaces around ternary operators.
staging: rtl8723bs: Fix lines with trailing open parentheses.
staging: rtl8723bs: Remove unnecessary length #define's.
staging: rtl8723bs: Fix IEEE80211 authentication algorithm constants.
staging: rtl8723bs: Fix alignment in rtw_wx_set_auth().
staging: rtl8723bs: Remove braces from single statement conditionals.
staging: rtl8723bs: Remove unecessary braces from switch statement.
staging: rtl8723bs: Fix newlines in rtw_wx_set_auth().
...
Based on the previous patches, this patch supports the LPC host on
Hip06/Hip07 for ACPI FW.
It is the responsibility of the LPC host driver to enumerate the child
devices, as the ACPI scan code will not enumerate children of "indirect IO"
hosts.
The ACPI table for the LPC host controller and the child devices is in the
following format:
Device (LPC0) {
Name (_HID, "HISI0191") // HiSi LPC
Name (_CRS, ResourceTemplate () {
Memory32Fixed (ReadWrite, 0xa01b0000, 0x1000)
})
}
Device (LPC0.IPMI) {
Name (_HID, "IPI0001")
Name (LORS, ResourceTemplate() {
QWordIO (
ResourceConsumer,
MinNotFixed, // _MIF
MaxNotFixed, // _MAF
PosDecode,
EntireRange,
0x0, // _GRA
0xe4, // _MIN
0x3fff, // _MAX
0x0, // _TRA
0x04, // _LEN
, ,
BTIO
)
})
Since the IO resources of the child devices need to be translated from LPC
bus addresses to logical PIO addresses, and we shouldn't modify the
resources of the devices generated in the FW scan, a per-child MFD is
created as a substitute. The MFD IO resources will be the translated bus
addresses of the ACPI child.
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Zhichang Yuan <yuanzhichang@hisilicon.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
The low-pin-count (LPC) interface of Hip06/Hip07 accesses I/O port space of
peripherals.
Implement the LPC host controller driver which performs the I/O operations
on the underlying hardware. We don't want to touch existing drivers such
as ipmi-bt, so this driver applies the indirect-IO introduced in the
previous patch after registering an indirect-IO node to the indirect-IO
devices list which will be searched by the I/O accessors to retrieve the
host-local I/O port.
The driver config is set as a bool instead of a tristate. The reason here
is that, by the very nature of the driver providing a logical PIO range, it
does not make sense to have this driver as a loadable module. Another more
specific reason is that the Huawei D03 board which includes Hip06 SoC
requires the LPC bus for UART console, so should be built in.
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Zou Rongrong <zourongrong@huawei.com>
Signed-off-by: Zhichang Yuan <yuanzhichang@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Rob Herring <robh@kernel.org> # dts part
The userspace support for fsl-mc requires a fsl_mc_allocator
cleanup function. Add the needed function.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "struct mc_command" is a very generic name for a global
kernel structure. Change its name in "struct fsl_mc_command".
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the source files out of staging into their final locations:
- dpcon.c goes to drivers/bus/fsl-mc/, next to the core infrastructure
- dpcon-cmd.h gets merged into drivers/bus/fsl-mc/fsl-mc-private.h, next
to the other internally used APIs
- dpcon.h gets merged into include/linux/fsl/mc.h, exposing the public
API
Update references in the dpaa2-eth staging driver.
DPCON stands for Data Path Concentrator - an interface between DPIO
(Data Path IO) and its users (e.g. dpaa2-eth). You can read more about
DPIO in Documentation/networking/dpaa2/overview.rst
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the source files out of staging into their final locations:
- dpbp.c goes to drivers/bus/fsl-mc/, next to the core infrastructure
- dpbp-cmd.h gets merged into drivers/bus/fsl-mc/fsl-mc-private.h, next
to the other internally used APIs
- dpbp.h gets merged into include/linux/fsl/mc.h, exposing the public
API
Update references in the dpaa2-eth staging driver.
DPBP stands for Data Path Buffer Pool - you can read more about the
object in Documentation/networking/dpaa2/overview.rst
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all the grouping is done with RB trees, we no longer need
group_entry and can replace the whole thing with sibling_list.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Carrillo-Cisneros <davidcc@google.com>
Cc: Dmitri Prokhorov <Dmitry.Prohorov@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Valery Cherepennikov <valery.cherepennikov@intel.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This series of changes enables the use device tree based sysconfig
data for ti-sysc driver. As we already have SmartReflex data configured,
we use that as the first driver to enable. To do that in a way where
SmartReflex is not probed twice, we need to prepare the SmartReflex
driver before flipping dts data on for it in the last patch of the
series.
To avoid regressions, we are checking the passed dts data against
existing platform data since we still have it available. Then after the
dts files are converted, we can simply drop the related platform data
at some point in the future.
-----BEGIN PGP SIGNATURE-----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=/hJY
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.17/ti-sysc-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Pull "Driver changes for ti-sysc for v4.17" from Tony Lindgren:
This series of changes enables the use device tree based sysconfig
data for ti-sysc driver. As we already have SmartReflex data configured,
we use that as the first driver to enable. To do that in a way where
SmartReflex is not probed twice, we need to prepare the SmartReflex
driver before flipping dts data on for it in the last patch of the
series.
To avoid regressions, we are checking the passed dts data against
existing platform data since we still have it available. Then after the
dts files are converted, we can simply drop the related platform data
at some point in the future.
* tag 'omap-for-v4.17/ti-sysc-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Enable ti-sysc to use device tree data for smartreflex
PM / AVS: SmartReflex: Prepare to use device tree based probing
ARM: OMAP2+: Try to parse earlycon from parent too
ARM: OMAP2+: Add checks for device tree based sysconfig data
ARM: OMAP2+: Add functions to allocate module data from device tree
bus: ti-sysc: Handle some devices in omap_device compatible way
bus: ti-sysc: Add support for platform data callbacks
bus: ti-sysc: Remove unnecessary debugging statements
bus: ti-sysc: Improve handling for no-reset-on-init and no-idle-on-init
bus: ti-sysc: Handle stdout-path for debug console
bus: ti-sysc: Add suspend and resume handling
bus: ti-sysc: Add fck clock alias for children with notifier_block
ARM: OMAP2+: Prepare to pass auxdata for smartreflex
Depending directly on the bus driver's global cci_ctrl_base variable
is a little unpleasant, and exporting it to allow the PMU driver to
be modular would be even more so. Let's make things a little better
abstracted by adding the control register block to the cci_pmu instance
data alongside the PMU register block, and communicating the mapped
address from the bus driver via platform data.
It's not practical to try the same thing for the bus driver itself,
given that the globals are entangled with the hairy assembly code for
port control, so we leave them be there. It would however be prudent
to move them to the __ro_after_init section in passing, since the
addresses really should never be changing once set.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rather than iterating over child nodes explicitly testing for
availability, we can just use the other helper which already subsumes
that check. Also, the availability check is already NULL-safe, so get
rid of a redundant check in cci_probe(), too.
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The arm-cci driver is really two entirely separate drivers; one for MCPM
port control and the other for the performance monitors. Since they are
already relatively self-contained, let's take the plunge and move the
PMU parts out to drivers/perf where they belong these days. For non-MCPM
systems this leaves a small dependency on the remaining "bus" stub for
initial probing and discovery, but we end up with something that still
fits the general pattern of its fellow system PMU drivers to ease future
maintenance.
Moving code to a new file also offers a perfect excuse to modernise the
license/copyright headers and clean up some funky linewraps on the way.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Suzuki Poulose <suzuki.poulose@arm.com>
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The arm-ccn driver is purely a perf driver for the CCN PMU, not a bus
driver in the sense of the other residents of drivers/bus/, so let's
move it to the appropriate place for SoC PMU drivers. Not to mention
moving the documentation accordingly as well.
Acked-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that ti-sysc can manage child devices, we must also be backwards
compatible with the current omap_device code. With omap_device, we
assume that the child device manages the interconnect target module
directly.
The drivers needing special handling are the ones that still set
pm_runtime_irq_safe(). In the long run we want to update those drivers
as otherwise they will cause problems with genpd as a permanent PM
runtime usage count is set on the parent device.
We can handle omap_device these devices by improving the ti-sysc quirk
handling to detect the devices needing special handling based on
register map and revision register if usable. We also need to implement
dev_pm_domain for these child devices just like omap_device does.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to pass the device tree configuration for interconnect target
modules from ti-sysc driver to the existing platform hwmod code.
This allows us to first validate the dts data against the existing
platform data before we start dropping the platform data in favor of
device tree data.
To do this, let's add platform data callbacks for PM runtime functions
to call for the interconnect target modules if platform data is
available.
Note that as ti-sysc driver can rebind, omap_auxdata_lookup and related
functions can no longer be __init.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We already show the status for the interconnect target module
when debugging is enabled, there's no need to be more verbose
about that. So let's just cut down the noise and remove the
extra debug statements.
Signed-off-by: Tony Lindgren <tony@atomide.coM>
At least earlycon needs a delayed idle before the 8250 driver probes
to avoid glitches in the console output. Let's handle the delayed idle
for devices tagged with ti,no-reset-on-init and ti,no-idle-on-init with
delayed_work. Others don't need it, and there should be no need to use
runtime PM autosuspend for the interconnect target driver as it's the
child device drivers that should configure it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
If we have stdout-path specified for earlycon, we must prevent
the debug console from idling until runtime PM kicks in.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The functional clock is used by several child device drivers to query
the rate for the child device internal configuration. The functional
clock is really for the whole interconnect target module, and not just
for the child device, and can also be shared across multiple children.
At least the timers, i2c and mmc driver query the fck for rate.
So let's just create a clock alias for the child fck if it does not
yet exits. We can do this with the BUS_NOTIFY_ADD_DEVICE before the
child is probed.
Note that we need to now also remove the legacy mode check for getting
the dts clocks in ti-sysc driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the source files out of staging into their final locations:
-mc.h include file in drivers/staging/fsl-mc/include go to include/linux/fsl
-source files in drivers/staging/fsl-mc/bus go to drivers/bus/fsl-mc
-overview.rst, providing an overview of DPAA2, goes to
Documentation/networking/dpaa2/overview.rst
Update or delete other remaining staging files -- Makefile, Kconfig, TODO.
Update dpaa2_eth and dpio staging drivers.
Add integration bits for the documentation build system.
Signed-off-by: Stuart Yoder <stuyoder@gmail.com>
[rebased, add dpaa2_eth and dpio #include updates]
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
[rebased, split irqchip to separate patch]
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are currently only checking for the first entry in the table while
we should check them all. Usual no-idle-on-init is together with
no-reset-on-init, so this has gone unnoticed.
Fixes: 566a9b05e1 ("bus: ti-sysc: Handle module quirks based dts
configuration")
Signed-off-by: Tony Lindgren <tony@atomide.com>
A number of new drivers get added this time, along with many low-priority
bugfixes. The most interesting changes by subsystem are:
bus drivers:
- Updates to the Broadcom bus interface driver to support newer SoC types
- The TI OMAP sysc driver now supports updated DT bindings
memory controllers:
- A new driver for Tegra186 gets added
- A new driver for the ti-emif sram, to allow relocating
suspend/resume handlers there
SoC specific:
- A new driver for Qualcomm QMI, the interface to the modem on MSM SoCs
- A new driver for power domains on the actions S700 SoC
- A driver for the Xilinx Zynq VCU logicoreIP
reset controllers:
- A new driver for Amlogic Meson-AGX
- various bug fixes
tee subsystem:
- A new user interface got added to enable asynchronous communication
with the TEE supplicant.
- A new method of using user space memory for communication with
the TEE is added
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yz0k
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A number of new drivers get added this time, along with many
low-priority bugfixes. The most interesting changes by subsystem are:
bus drivers:
- Updates to the Broadcom bus interface driver to support newer SoC
types
- The TI OMAP sysc driver now supports updated DT bindings
memory controllers:
- A new driver for Tegra186 gets added
- A new driver for the ti-emif sram, to allow relocating
suspend/resume handlers there
SoC specific:
- A new driver for Qualcomm QMI, the interface to the modem on MSM
SoCs
- A new driver for power domains on the actions S700 SoC
- A driver for the Xilinx Zynq VCU logicoreIP
reset controllers:
- A new driver for Amlogic Meson-AGX
- various bug fixes
tee subsystem:
- A new user interface got added to enable asynchronous communication
with the TEE supplicant.
- A new method of using user space memory for communication with the
TEE is added"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (84 commits)
of: platform: fix OF node refcount leak
soc: fsl: guts: Add a NULL check for devm_kasprintf()
bus: ti-sysc: Fix smartreflex sysc mask
psci: add CPU_IDLE dependency
soc: xilinx: Fix Kconfig alignment
soc: xilinx: xlnx_vcu: Use bitwise & rather than logical && on clkoutdiv
soc: xilinx: xlnx_vcu: Depends on HAS_IOMEM for xlnx_vcu
soc: bcm: brcmstb: Be multi-platform compatible
soc: brcmstb: biuctrl: exit without warning on non brcmstb platforms
Revert "soc: brcmstb: Only register SoC device on STB platforms"
bus: omap: add MODULE_LICENSE tags
soc: brcmstb: Only register SoC device on STB platforms
tee: shm: Potential NULL dereference calling tee_shm_register()
soc: xilinx: xlnx_vcu: Add Xilinx ZYNQMP VCU logicoreIP init driver
dt-bindings: soc: xilinx: Add DT bindings to xlnx_vcu driver
soc: xilinx: Create folder structure for soc specific drivers
of: platform: populate /firmware/ node from of_platform_default_populate_init()
soc: samsung: Add SPDX license identifiers
soc: qcom: smp2p: Use common error handling code in qcom_smp2p_probe()
tee: shm: don't put_page on null shm->pages
...
the smartreflex interconnect target module for device tree based
probing.
-----BEGIN PGP SIGNATURE-----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=4cMv
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/ti-sysc-fix-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
Pull "one ti-sysc driver fix for v4.16 merge window" from Tony Lindgren:
One minor fix for ti-sysc smartreflex sysc mask that prevents idling
the smartreflex interconnect target module for device tree based
probing.
* tag 'omap-for-v4.16/ti-sysc-fix-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix smartreflex sysc mask
The enawakeup bit is in a different location for smartreflex compared
to the "ti,sysc-omap2" compatible.
Fixes: 70a65240ef ("bus: ti-sysc: Add register bits for interconnect
target modules")
Signed-off-by: Tony Lindgren <tony@atomide.com>
linux-4.15 warns about missing MODULE_LICENSE tags such as these
WARNING: modpost: missing MODULE_LICENSE() in drivers/bus/omap_l3_noc.o
WARNING: modpost: missing MODULE_LICENSE() in drivers/bus/omap_l3_smx.o
For completeness, I'm also adding MODULE_AUTHOR and MODULE_DESCRIPTION
tags, but I decided to leave out the email addresses, as all three
authors are working for other companies now.
Cc: Sricharan R <sricharan@codeaurora.org>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
We now have gotten ti-sysc driver to the point where it can parse
interconnect target configuration from device tree instead of the
legacy platform data. This series updates the device tree binding
and adds parsing to the driver for quirks and capabilities.
-----BEGIN PGP SIGNATURE-----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=Hwvv
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
TI sysc driver updates for v4.16 merge window
We now have gotten ti-sysc driver to the point where it can parse
interconnect target configuration from device tree instead of the
legacy platform data. This series updates the device tree binding
and adds parsing to the driver for quirks and capabilities.
* tag 'omap-for-v4.16/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Add parsing of module capabilities
bus: ti-sysc: Handle module quirks based dts configuration
bus: ti-sysc: Detect i2c interconnect target module based on register layout
bus: ti-sysc: Add register bits for interconnect target modules
bus: ti-sysc: Make omap_hwmod_sysc_fields into sysc_regbits platform data
ARM: OMAP2+: Move all omap_hwmod_sysc_fields to omap_hwmod_common_data.c
ARM: dts: Add generic ti,sysc compatible in addition to the custom ones
dt-bindings: ti-sysc: Update binding for timers and capabilities
Signed-off-by: Olof Johansson <olof@lixom.net>
First, one fix that adds proper regulator references for the EMAC
external PHYs on A64 boards. The EMAC bindings were developed for 4.13,
but reverted at the last minute. They were finalized and brought back
for 4.15. However in the time between, regulator support for the A64
boards was merged. When EMAC device tree changes were reintroduced,
this was not taken into account.
Second, a patch that adds OF based modalias uevent for RSB slave devices.
This has been missing since the introduction of RSB, and recently with
PMIC regulator support introduced for the A64, has been seen affecting
distributions, which have the all-important PMIC mfd drivers built as
modules, which then don't get loaded.
Other minor cleanups include final conversion of raw indices to CCU
binding macros for sun[4567]i HDMI, cleanup of dummy regulators on the
A64 SOPINE, a SD card detection polarity fix for the Orange Pi Zero
Plus2, and adding a missing compatible for the PMIC on the TBS A711
tablet.
-----BEGIN PGP SIGNATURE-----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=FCgU
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Pull "Allwinner fixes for 4.15" from Chen-Yu Tsai:
First, one fix that adds proper regulator references for the EMAC
external PHYs on A64 boards. The EMAC bindings were developed for 4.13,
but reverted at the last minute. They were finalized and brought back
for 4.15. However in the time between, regulator support for the A64
boards was merged. When EMAC device tree changes were reintroduced,
this was not taken into account.
Second, a patch that adds OF based modalias uevent for RSB slave devices.
This has been missing since the introduction of RSB, and recently with
PMIC regulator support introduced for the A64, has been seen affecting
distributions, which have the all-important PMIC mfd drivers built as
modules, which then don't get loaded.
Other minor cleanups include final conversion of raw indices to CCU
binding macros for sun[4567]i HDMI, cleanup of dummy regulators on the
A64 SOPINE, a SD card detection polarity fix for the Orange Pi Zero
Plus2, and adding a missing compatible for the PMIC on the TBS A711
tablet.
* tag 'sunxi-fixes-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a711: Reinstate the PMIC compatible
arm64: dts: orange-pi-zero-plus2: fix sdcard detect
arm64: allwinner: a64-sopine: Fix to use dcdc1 regulator instead of vcc3v3
ARM: dts: sunxi: Convert to CCU index macros for HDMI controller
sunxi-rsb: Include OF based modalias in device uevent
arm64: allwinner: a64: add Ethernet PHY regulator for several boards
We need to configure the interconnect target module based on the
device three configuration.
Let's also add a new quirk for SYSC_QUIRK_RESET_STATUS to indicate
that the SYSCONFIG reset bit changes after the reset is done.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's configure few module quirks via device tree using the
properties for "ti,no-idle-on-init", "ti,no-reset-on-init"
and "ti,sysc-delay-us".
Let's also reorder the probe a bit so we have pdata available
earlier, and move the PM runtime calls to sysc_init_module()
from sysc_read_revision().
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can easily detect i2c based on it's non-standard module registers that
consist of two 32-bit registers accessed in 16-bit mode.
So far we don't have other 16-bit modules, so there's currently no need
to add a custom property for 16-bit register access.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's add data for the known interconnect target module types by mapping
their register bits.
Note that we can handle many quirks for the older omap2 type1 modules
directly in the driver without a need for adding custom properties.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Kconfig currently controlling compilation of this code is:
config SIMPLE_PM_BUS
bool "Simple Power-Managed Bus Driver"
...meaning that it currently is not being built as a module by anyone.
In removing the orphaned modular support in a previous patch set,
Geert indicated he'd rather see this code converted to tristate.
I normally don't do that because it extends functionality that I
can't easily run time test or even know if the use case makes sense,
but since in this case the author has nominated it as such, we do
the conversion here.
Note that doesn't change the lack of run time testing ; this change
is only tested for sucessful compile and modpost.
[geert: Ethernet is probed successfully on sh73a0/kzm9g after
insmodding simple-pm-bus.ko]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Include the OF-based modalias in the uevent sent when registering devices
on the sunxi RSB bus, so that user space has a chance to autoload the
kernel module for the device.
Fixes a regression caused by commit 3f241bfa60 ("arm64: allwinner: a64:
pine64: Use dcdc1 regulator for mmc0"). When the axp20x-rsb module for
the AXP803 PMIC is built as a module, it is not loaded and the system
ends up with an disfunctional MMC controller.
Fixes: d787dcdb9c ("bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus")
Cc: stable <stable@vger.kernel.org> # 4.4.x 7a3b7cd332 of: device: Export of_device_{get_modalias, uvent_modalias} to modules
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ARM CCI driver seem to be using smp_processor_id() in a
preemptible context, which is likely to make a DEBUG_PREMPT
kernel scream at boot time.
Turn this into a get_cpu()/put_cpu() that extends over the CPU
hotplug registration, making sure that we don't race against
a CPU down operation.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Booting a DEBUG_PREEMPT enabled kernel on a CCN-based system
results in the following splat:
[...]
arm-ccn e8000000.ccn: No access to interrupts, using timer.
BUG: using smp_processor_id() in preemptible [00000000] code: swapper/0/1
caller is debug_smp_processor_id+0x1c/0x28
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.13.0 #6111
Hardware name: AMD Seattle/Seattle, BIOS 17:08:23 Jun 26 2017
Call trace:
[<ffff000008089e78>] dump_backtrace+0x0/0x278
[<ffff00000808a22c>] show_stack+0x24/0x30
[<ffff000008bc3bc4>] dump_stack+0x8c/0xb0
[<ffff00000852b534>] check_preemption_disabled+0xfc/0x100
[<ffff00000852b554>] debug_smp_processor_id+0x1c/0x28
[<ffff000008551bd8>] arm_ccn_probe+0x358/0x4f0
[...]
as we use smp_processor_id() in the wrong context.
Turn this into a get_cpu()/put_cpu() that extends over the CPU hotplug
registration, making sure that we don't race against a CPU down operation.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Use 'devm_kasprintf()' to simplify the code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
9074 5592 416 15082 3aea drivers/bus/arm-ccn.o
File size After adding 'const':
text data bss dec hex filename
9327 5336 416 15079 3ae7 drivers/bus/arm-ccn.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
This branch contains platform-related driver updates for ARM and ARM64,
these are the areas that bring the changes:
New drivers:
- Driver support for Renesas R-Car V3M (R8A77970)
- Power management support for Amlogic GX
- A new driver for the Tegra BPMP thermal sensor
- A new bus driver for Technologic Systems NBUS
Changes for subsystems that prefer to merge through arm-soc:
- The usual updates for reset controller drivers from Philipp Zabel,
with five added drivers for SoCs in the arc, meson, socfpa, uniphier
and mediatek families.
- Updates to the ARM SCPI and PSCI frameworks, from Sudeep Holla,
Heiner Kallweit and Lorenzo Pieralisi.
Changes specific to some ARM-based SoC
- The Freescale/NXP DPAA QBMan drivers from PowerPC can now work
on ARM as well.
- Several changes for power management on Broadcom SoCs
- Various improvements on Qualcomm, Broadcom, Amlogic, Atmel, Mediatek
- Minor Cleanups for Samsung, TI OMAP SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qDhq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This branch contains platform-related driver updates for ARM and
ARM64, these are the areas that bring the changes:
New drivers:
- driver support for Renesas R-Car V3M (R8A77970)
- power management support for Amlogic GX
- a new driver for the Tegra BPMP thermal sensor
- a new bus driver for Technologic Systems NBUS
Changes for subsystems that prefer to merge through arm-soc:
- the usual updates for reset controller drivers from Philipp Zabel,
with five added drivers for SoCs in the arc, meson, socfpa,
uniphier and mediatek families
- updates to the ARM SCPI and PSCI frameworks, from Sudeep Holla,
Heiner Kallweit and Lorenzo Pieralisi
Changes specific to some ARM-based SoC
- the Freescale/NXP DPAA QBMan drivers from PowerPC can now work on
ARM as well
- several changes for power management on Broadcom SoCs
- various improvements on Qualcomm, Broadcom, Amlogic, Atmel,
Mediatek
- minor Cleanups for Samsung, TI OMAP SoCs"
[ NOTE! This doesn't work without the previous ARM SoC device-tree pull,
because the R8A77970 driver is missing a header file that came from
that pull.
The fact that this got merged afterwards only fixes it at this point,
and bisection of that driver will fail if/when you walk into the
history of that driver. - Linus ]
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (96 commits)
soc: amlogic: meson-gx-pwrc-vpu: fix power-off when powered by bootloader
bus: add driver for the Technologic Systems NBUS
memory: omap-gpmc: Remove deprecated gpmc_update_nand_reg()
soc: qcom: remove unused label
soc: amlogic: gx pm domain: add PM and OF dependencies
drivers/firmware: psci_checker: Add missing destroy_timer_on_stack()
dt-bindings: power: add amlogic meson power domain bindings
soc: amlogic: add Meson GX VPU Domains driver
soc: qcom: Remote filesystem memory driver
dt-binding: soc: qcom: Add binding for rmtfs memory
of: reserved_mem: Accessor for acquiring reserved_mem
of/platform: Generalize /reserved-memory handling
soc: mediatek: pwrap: fix fatal compiler error
soc: mediatek: pwrap: fix compiler errors
arm64: mediatek: cleanup message for platform selection
soc: Allow test-building of MediaTek drivers
soc: mediatek: place Kconfig for all SoC drivers under menu
soc: mediatek: pwrap: add support for MT7622 SoC
soc: mediatek: pwrap: add common way for setup CS timing extenstion
soc: mediatek: pwrap: add MediaTek MT6380 as one slave of pwrap
..
Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are
OMAP, Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now
with a Quad-Core ARM Cortex-A7. According to the manufacturer,
it is intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family
of chips meant for managed gigabit ethernet switches, based
around a Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2
and Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jlJ2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are OMAP,
Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now with a
Quad-Core ARM Cortex-A7. According to the manufacturer, it is
intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family of
chips meant for managed gigabit ethernet switches, based around a
Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2 and
Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (118 commits)
ARM: multi_v7_defconfig: Select RPMSG_VIRTIO as module
ARM: multi_v7_defconfig: enable CONFIG_GPIO_UNIPHIER
arm64: defconfig: enable CONFIG_GPIO_UNIPHIER
ARM: meson: enable MESON_IRQ_GPIO in Kconfig for meson8b
ARM: meson: Add SMP bringup code for Meson8 and Meson8b
ARM: smp_scu: allow the platform code to read the SCU CPU status
ARM: smp_scu: add a helper for powering on a specific CPU
dt-bindings: Amlogic: Add Meson8 and Meson8b SMP related documentation
ARM: OMAP3: Delete an unnecessary variable initialisation in omap3xxx_hwmod_init()
ARM: OMAP3: Use common error handling code in omap3xxx_hwmod_init()
ARM: defconfig: select the right SX150X driver
arm64: defconfig: Enable QCOM_IOMMU
arm64: Add ThunderX drivers to defconfig
arm64: defconfig: Enable Tegra PCI controller
cpufreq: imx6q: Move speed grading check to cpufreq driver
arm64: defconfig: re-enable Qualcomm DB410c USB
ARM: configs: stm32: Add MDMA support in STM32 defconfig
ARM: imx: Enable cpuidle for i.MX6DL starting at 1.1
bus: ti-sysc: Fix unbalanced pm_runtime_enable by adding remove
bus: ti-sysc: mark PM functions as __maybe_unused
...
Plenty of acronym soup here:
- Initial support for the Scalable Vector Extension (SVE)
- Improved handling for SError interrupts (required to handle RAS events)
- Enable GCC support for 128-bit integer types
- Remove kernel text addresses from backtraces and register dumps
- Use of WFE to implement long delay()s
- ACPI IORT updates from Lorenzo Pieralisi
- Perf PMU driver for the Statistical Profiling Extension (SPE)
- Perf PMU driver for Hisilicon's system PMUs
- Misc cleanups and non-critical fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJaCcLqAAoJELescNyEwWM0JREH/2FbmD/khGzEtP8LW+o9D8iV
TBM02uWQxS1bbO1pV2vb+512YQO+iWfeQwJH9Jv2FZcrMvFv7uGRnYgAnJuXNGrl
W+LL6OhN22A24LSawC437RU3Xe7GqrtONIY/yLeJBPablfcDGzPK1eHRA0pUzcyX
VlyDruSHWX44VGBPV6JRd3x0vxpV8syeKOjbRvopRfn3Nwkbd76V3YSfEgwoTG5W
ET1sOnXLmHHdeifn/l1Am5FX1FYstpcd7usUTJ4Oto8y7e09tw3bGJCD0aMJ3vow
v1pCUWohEw7fHqoPc9rTrc1QEnkdML4vjJvMPUzwyTfPrN+7uEuMIEeJierW+qE=
=0qrg
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"The big highlight is support for the Scalable Vector Extension (SVE)
which required extensive ABI work to ensure we don't break existing
applications by blowing away their signal stack with the rather large
new vector context (<= 2 kbit per vector register). There's further
work to be done optimising things like exception return, but the ABI
is solid now.
Much of the line count comes from some new PMU drivers we have, but
they're pretty self-contained and I suspect we'll have more of them in
future.
Plenty of acronym soup here:
- initial support for the Scalable Vector Extension (SVE)
- improved handling for SError interrupts (required to handle RAS
events)
- enable GCC support for 128-bit integer types
- remove kernel text addresses from backtraces and register dumps
- use of WFE to implement long delay()s
- ACPI IORT updates from Lorenzo Pieralisi
- perf PMU driver for the Statistical Profiling Extension (SPE)
- perf PMU driver for Hisilicon's system PMUs
- misc cleanups and non-critical fixes"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (97 commits)
arm64: Make ARMV8_DEPRECATED depend on SYSCTL
arm64: Implement __lshrti3 library function
arm64: support __int128 on gcc 5+
arm64/sve: Add documentation
arm64/sve: Detect SVE and activate runtime support
arm64/sve: KVM: Hide SVE from CPU features exposed to guests
arm64/sve: KVM: Treat guest SVE use as undefined instruction execution
arm64/sve: KVM: Prevent guests from using SVE
arm64/sve: Add sysctl to set the default vector length for new processes
arm64/sve: Add prctl controls for userspace vector length management
arm64/sve: ptrace and ELF coredump support
arm64/sve: Preserve SVE registers around EFI runtime service calls
arm64/sve: Preserve SVE registers around kernel-mode NEON use
arm64/sve: Probe SVE capabilities and usable vector lengths
arm64: cpufeature: Move sys_caps_initialised declarations
arm64/sve: Backend logic for setting the vector length
arm64/sve: Signal handling support
arm64/sve: Support vector length resetting for new processes
arm64/sve: Core task context handling
arm64/sve: Low-level CPU setup
...
This driver implements a GPIOs bit-banged bus, called the NBUS by
Technologic Systems. It is used to communicate with the peripherals in
the FPGA on the TS-4600 SoM.
Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When the PMU driver is built as a module, the perf expects the
pmu->module to be valid, so that the driver is prevented from
being unloaded while it is in use. Fix the CCN pmu driver to
fill in this field.
Fixes: a33b0daab7 ("bus: ARM CCN PMU driver")
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like we're missing remove() that's needed if a driver instance
rebound. Otherwise we will get "Unbalanced pm_runtime_enable!".
Signed-off-by: Tony Lindgren <tony@atomide.com>
The new bus driver causes a harmless compile-time warning when
CONFIG_PM is disabled:
drivers/bus/ti-sysc.c:440:12: error: 'sysc_runtime_resume' defined but not used [-Werror=unused-function]
static int sysc_runtime_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~
drivers/bus/ti-sysc.c:421:12: error: 'sysc_runtime_suspend' defined but not used [-Werror=unused-function]
static int sysc_runtime_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~~~~
This marks the two unused functions as __maybe_unused to shut up
that warning.
Fixes: 0eecc636e5 ("bus: ti-sysc: Add minimal TI sysc interconnect target driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
At least the Armada XP SoC supports 4GB on a single DRAM window. Because
the size register values contain the actual size - 1, the MSB is set in
that case. For example, the SDRAM window's control register's value is
0xffffffe1 for 4GB (bits 31 to 24 contain the size).
The MBUS driver reads back each window's size from registers and
calculates the actual size as (control_reg | ~DDR_SIZE_MASK) + 1, which
overflows for 32 bit values, resulting in other miscalculations further
on (a bad RAM window for the CESA crypto engine calculated by
mvebu_mbus_setup_cpu_target_nooverlap() in my case).
This patch changes the type in 'struct mbus_dram_window' from u32 to
u64, which allows us to keep using the same register calculation code in
most MBUS-using drivers (which calculate ->size - 1 again).
Fixes: fddddb52a6 ("bus: introduce an Marvell EBU MBus driver")
CC: stable@vger.kernel.org
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
