This was tested on actual hardware and found to work fine, but currently
the official specifications of this chip could not be obtained to
confirm the numbers.
Signed-off-by: Leonid Bloch <lbloch@janustech.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DIO connector on the WAFER-945GSE is interfaced to GPIO ports
on the ITE IT8718F Super I/O chipset. From the datasheet of ITE IT8718F,
the GPIO interface is identical to IT8728, so just add it
to the same case as the other chip.
Signed-off-by: Ivan Podovalov <ipodovalov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
From the datasheet, the GPIO interface is identical to IT8728 (same
description), so just add it to the same case as the other chip.
Signed-off-by: Vincent Prince <vincent.prince.fr@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
From the datasheet, the GPIO interface is identical to IT8728 (same
description), so just add it to the same case as the other chip.
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only used to copy into other structures, so declare
them as const.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These chips seem to have a 9th GPIO block (thus supporting 72 GPIOs)
which is configured through SuperIO register 0xd2 (output enable) and
0xd3 (simple I/O). This is also the reason why io_size is larger than
on IT8728 / IT8732. Unfortunately I don't have hardware to test this 9th
GPIO block.
I am also not sure about not configuring the Simple I/O registers as the
hardware I have only uses GPIO block 8. Reading back the values of
0xc0-0xc7 (as configured by the BIOS/EFI on my board) shows that all
have 0xff set.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for the GPIOs found on the ITE super-I/O chips
IT87xx.
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Signed-off-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
