This patch updates the regulator driver to add support
for TWL6030 PMIC specific LDO regulators.
SMPS resources are not yet supported for TWL6030 and
also .set_mode and .get_status for LDO's are yet to
be implemented for TWL6030.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch renames all twl4030_ functions to twl so that regulator driver
can be reused by Triton - TWL4030 and Phoenix - TWL6030.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch renames function names like twl4030_i2c_write_u8,
twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8
and also common variable in twl-core.c
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Bring the WM8350 IRQ API more in line with the generic IRQ API by
masking and unmasking interrupts as they are requested and freed.
This is mostly just a case of deleting the mask and unmask calls
from the individual drivers.
The RTC driver is changed to mask the periodic IRQ after requesting
it rather than only unmasking the alarm IRQ. If the periodic IRQ
fires in the period where it is reqested then there will be a
spurious notification but there should be no serious consequences
from this.
The CODEC drive is changed to explicitly disable headphone jack
detection prior to requesting the IRQs. This will avoid the IRQ
firing with no jack set up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is done as simple code transformation, the semantics of the
IRQ API provided by the core are are still very different to those
of genirq (mainly with regard to masking).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently the pcf50633-regulator driver data is set to the pcf50633 core
structure, but the pcf50633-regulator remove handler assumes that it is set to
the regulator device. This patch fixes the issue by accessing the pcf506533
core structure through its parent device and setting the driver data to the
regulator device.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The version that made it into mainline missed the initialisation of the
chip handle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Don't dereference drvdata after it has been freed.
regards,
dan carpenter
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If ret is unsigned, the checks for negative wm831x_reg_read() return values
are wrong. The error value should be transmitted to its caller, e.g.
wm831x_gp_ldo_get_status() which tests for a negative return value.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Specifying 'default n' is superfluous.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
For val to be greater than 7 or less than 20 is logically always true.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This makes _regulator_enable() properly handle the case where
a regulator is already on when you try to enable it. Currently
it will erroneously handle positive return values as an error.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Fixes the following errors on both tps650xx regulator drivers :-
drivers/regulator/tps65023-regulator: struct i2c_device_id is 32 bytes. The last of 1 is:
0x74 0x70 0x73 0x36 0x35 0x30 0x32 0x33 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
FATAL: drivers/regulator/tps65023-regulator: struct i2c_device_id is not terminated with a NULL entry!
This patch also fixes the GPL v2 licence string for both drivers.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Adding TPS65023 and TPS6507x regulator driver support in
drivers/regulator/Makefile and drivers/regulator/Kconfig
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Adding support for TI TPS6507x regulator driver
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Adding support for TI TPS65023 regulator driver
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
and avoid introducing our own loops for creating
several sysfs entries.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Now fixed regulators that have their enable pin connected to a GPIO line
can use the fixed regulator driver for regulator enable/disable control.
The GPIO number and polarity information is passed through platform data.
GPIO enable control is achieved using gpiolib.
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Reviewed-by: Philipp Zabel <philipp.zabel@gmail.com>
Reviewed-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch implements list_voltage for the pcf50644 regulator driver.
As the voltages are linearly scaled the code to convert register values to
voltages can be reused and most of the code can be shared with get_voltage.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The regulator_enable() code wasn't actually checking that the
machine constraints had given permission to enable the regulator.
Add code to do that, but only if the regulator is not already on
due to something like always_on or being left on at startup since
in those cases there's no physical change being introduced and the
constraint wouldn't make any sense.
Also add matching code for disable(). We need to do less there since
either regulator_enable() should have succeeded first or the board
setup makes no sense.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allows use by more of the internal regulator API code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Report errors to the user and try harder to clean up if we're not
able to probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The patch to add support for looking up consumers by device name
had the side effect of causing us to require a device which is
at best premature since at least cpufreq still operates outside
the device model. Remove that requirement.
Reported-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
We're probably going to start oopsing fairly soon after this happens.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Simplify checking of support for voltage ranges by providing an API which
wraps the existing count and list operations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some consumers require complete control of the regulator and can't
tolerate sharing it with other consumers, most commonly because they need
to have the regulator actually disabled so can't have other consumers
forcing it on. This new regulator_get_exclusive() API call allows these
consumers to explicitly request this, documenting the assumptions that
they are making.
In order to simplify coding of such consumers the use count for regulators
they request is forced to match the enabled state of the regulator when
it is requested. This is not possible for consumers which can share
regulators due to the need to keep track of the ownership of use counts.
A new API call is used rather than an additional argument to the existing
regulator_get() in order to avoid merge headaches with driver code in
other trees.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Make da903x driver to list voltage and count voltage.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In PXA3xx SoC family, V_CORE power doamin is supplied by BUCK1 that is
controller by ADTV1 or ADTV2 register.
By default, v1 and v2 has the same copy. If v1 or v2 is updated, the last
value that is written to either register takes effect. It means that v1
and v2 has different copy. And the actual voltage output is determinated
by last update on either register.
DA9034/35 is binded with PXA3xx SoC family. While SoC is scaling OP or
entering/exiting lower power mode, SoC needs to change voltage of V_CORE
power doamin. In order to be efficient, POWER I2C (hardcode) mode could
be enabled in SoC. In this mode, SoC will control v2 register directly.
In original DA903x driver, software will only read regulator data from v1
register. But SoC controls v2 register directly. It results that v1 and v2
isn't synchronized. Wrong data will be read from v1 register. So access v2
register in da903x driver instead.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Support the operation of DA9030 BUCK2 in da903x driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
BUCK3 is the new component in DA9035. So there're three BUCKs in DA9035.
And there're two BUCKs in DA9034.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Follow the approach suggested by Russell King and implemented by him in
the clkdev API and allow consumer device supply mapings to be set up
using the dev_name() for the consumer instead of the struct device.
In order to avoid making existing machines instabuggy and creating merge
issues the use of struct device is still supported for the time being.
This resolves problems working with buses such as I2C which make the
struct device available late providing that the final device name is
known, which is the case for most embedded systems with fixed setups.
Consumers must still use the struct device when calling regulator_get().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This makes it easier to read the logs when doing testing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The core will no longer complain so we should log an error here.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Ensure that reg is within the bounds of array wm8350->pmic.pdev[].
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This sets the number of voltages for the AB3100 regulators so that
they play well with the voltage listing functions and can be used
properly with the MMC regulator integration glue for example.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds support for the regulators found in the AB3100
Mixed-Signal IC.
It further also defines platform data for the ST-Ericsson
U300 platform and extends the AB3100 MFD driver so that
platform/board data with regulation constraints and an init
function can be passed down all the way from the board to
the regulators.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver provides basic support for the voltage regulators
integrated into the Freescale MC13783 PMIC. It is currently
only possible to enable/disable outputs, not to actually
set the voltage.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Right now the pcap core driver passes a reference to its pcap data abusing the
subdrivers platform drvdata, this is not good.
Get the reference directly from the parent device.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Register pcap-regulator earlier so it can be used with cpufreq
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rajendra Nayak