- Kirkwood
- a couple of small fixes for the Iomega ix2-200 board (ether and led)
- mvebu
- allow GPIO button to work on Mirabox when running SMP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRZZxwAAoJEAi3KVZQDZAerwcIAKR1xRKuagtXvfij+xfVVRQ6
1G645hTIthFXmNiEeo3Y/mswHhVooZvu8SWh3o3J2Wsbnzeh+ch6jTsl+g6Tnb3E
KmRFU0mcalRmsyYsh4PH9nDi8/oWyP+i3ZytgfcMlsSPNiE+Ek35NdTTWMLCTT8V
MkGysVc8MWoOmMf47mNboy5UUUTXRdnSUJSjv1ubrsTK33LT7Ii9Ce+eoNvpvF+5
+6RenfRMzRSwkZf9AaCRPAhXISQKbMAwz6lKGo2GGAW+73Z+JclXXmiCfQ8pWie2
pfyqiEYigZFqe6Ly5BUtGoVfDjmOLDs+ATTUDOlOj0uaEc7pOwwKoAtpVRdck24=
=yK1f
-----END PGP SIGNATURE-----
Merge tag 'mvebu_fixes_for_v3.9_round3' of git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper <jason@lakedaemon.net>:
mvebu fixes for v3.9 round 3
- Kirkwood
- a couple of small fixes for the Iomega ix2-200 board (ether and led)
- mvebu
- allow GPIO button to work on Mirabox when running SMP
* tag 'mvebu_fixes_for_v3.9_round3' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: Fix the irq map function in SMP mode
Fix GE0/GE1 init on ix2-200 as GE0 has no PHY
ARM: Kirkwood: Fix typo in the definition of ix2-200 rebuild LED
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch fix the regression introduced by the commit 3202bf0157
"arm: mvebu: Improve the SMP support of the interrupt controller":
GPIO IRQ were no longer delivered to the CPUs.
To be delivered to a CPU an interrupt must be enabled at CPU level and
at interrupt source level. Before the offending patch, all the
interrupts were enabled at source level during map() function. Mask()
and unmask() was done by handling the per-CPU part. It was fine when
running in UP with only one CPU.
The offending patch added support for SMP, in this case mask() and
unmask() was done by handling the interrupt source level part. The
per-CPU level part was handled by the affinity API to select the CPU
which will receive the interrupt. (Due to some hardware limitation
only one CPU at a time can received a given interrupt).
For "normal" interrupt __setup_irq() was called when an irq was
registered. irq_set_affinity() is called from this function, which
enabled the interrupt on one of the CPUs. Whereas for GPIO IRQ which
were chained interrupts, the irq_set_affinity() was never called and
none of the CPUs was selected to receive the interrupt.
With this patch all the interrupt are enable on the current CPU during
map() function. Enabling the interrupts on a CPU doesn't depend
anymore on irq_set_affinity() and then the chained irq are not anymore
a special case. However the CPU which will receive the irq can still
be modify later using irq_set_affinity().
Tested with Mirabox (A370) and Openblocks AX3 (AXP), rootfs mounted
over NFS, compiled with CONFIG_SMP=y/N.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reported-by: Ryan Press <ryan@presslab.us>
Investigated-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Ryan Press <ryan@presslab.us>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The external pending interrupt register address (EINTPEND) offset is
0xa8, not 0x08. Without this patch the external interrupts are not
properly acknowledged, which may lead to an interrupt storm and the
system hang as soon as any external interrupt is requested.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Due to NR_IRQS being incorrectly defined not all IRQ domains can
be registered for S3C2440. It causes following errors on a s3c2440
SoC based board:
NR_IRQS:89
S3C2440: IRQ Support
irq: clearing pending status 00000002
------------[ cut here ]------------
WARNING: at kernel/irq/irqdomain.c:234 0xc0056ed0()
...
irq: could not create irq-domain
...
s3c2410-wdt s3c2410-wdt: failed to install irq (-22)
s3c2410-wdt: probe of s3c2410-wdt failed with error -22
...
samsung-uart s3c2440-uart.0: cannot get irq 74
Fix this by increasing NR_IRQS to at least (IRQ_S3C2443_AC97 + 1)
if CPU_S3C2440 is selected, so the subintc IRQ domain gets properly
registered.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* A couple imx35 clock fixes for regressions caused by common clock
framework conversion. The admux and iomux get disabled by common
clock framework late initcall, and hence causes problems.
* Add missing twd clock lookup in device tree. This becomes required
since commit bd60345 (ARM: use device tree to get smp_twd clock)
forces all DT boot to find lookup from device tree.
* Fix imx6q ldb_di clock parents mismatch per reference manual.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRZAZBAAoJEFBXWFqHsHzOy60H/0RIxFO1TSQVVPTuJRtHr9qk
BtszcLOwiRbWipuG1OiosEKXMeOXjAPtOG8P9tReC/oJN4WL5CmGW3PrPQ/9DEbZ
OTYVPhgmGKDB/2n5BVvvTDISTovvlQRju4ht+70j1BnAlpbzGLbKMG4o6zHOROoh
d15dqg/Ny1ovsCvva2ODbwRtBkBaBqDC+RGqNPrhTN7WSk+nv6yITYZCREI1mjGH
RG7B62hn+1aD6tMdigFu9xS4vTkHXjFC0AVEixBEi3iWqofSz3Cb6Zq4MpRGNXGZ
o/tfc4/2q6uF/UEpTQJDhYbHjwesySsIwdu4vsvI2lh9EGqUgyC3YE+VbDwOeGE=
=tztW
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.9-5' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The imx fixes for 3.9, take 5:
* A couple imx35 clock fixes for regressions caused by common clock
framework conversion. The admux and iomux get disabled by common
clock framework late initcall, and hence causes problems.
* Add missing twd clock lookup in device tree. This becomes required
since commit bd60345 (ARM: use device tree to get smp_twd clock)
forces all DT boot to find lookup from device tree.
* Fix imx6q ldb_di clock parents mismatch per reference manual.
* tag 'imx-fixes-3.9-5' of git://git.linaro.org/people/shawnguo/linux-2.6: (217 commits)
ARM i.MX6: Fix ldb_di clock selection
ARM: imx: provide twd clock lookup from device tree
ARM: imx35 Bugfix admux clock
ARM: clk-imx35: Bugfix iomux clock
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
According to the recent i.MX6 Quad technical reference manual, mode 0x4 (100b)
of the CCM_CS2DCR register (address 0x020C402C) bits [11-9] and [14-12] select
the PLL3 clock, and not the PLL3 PFD1 540M clock. In our code, the PLL3 root
clock is named 'pll3_usb_otg', select this instead of the 540M clock.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
While booting from device tree, imx6q used to provide twd clock lookup
by calling clk_register_clkdev() in clock driver. However, the commit
bd60345 (ARM: use device tree to get smp_twd clock) forces DT boot to
look up the clock from device tree. It causes the failure below when
twd driver tries to get the clock, and hence kernel has to calibrate the
local timer frequency.
smp_twd: clock not found -2
...
Calibrating local timer... 396.13MHz.
Fix the regression by providing twd clock lookup from device tree, and
remove the unused twd clk_register_clkdev() call from clock driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The admux clock seems to be the audmux clock as tests show. audmux does
not work without this clock enabled. Currently imx35 does not register a
clock device for audmux. This patch adds this registration. imx-audmux
driver already handles a clock device, so no changes are necessary
there.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch enables iomuxc_gate clock. It is necessary to be able to
reconfigure iomux pads. Without this clock enabled, the
clk_disable_unused function will disable this clock and the iomux pads
are not configurable anymore. This happens at every boot. After a reboot
(watchdog system reset) the clock is not enabled again, so all iomux pad
reconfigurations in boot code are without effect.
The iomux pads should be always configurable, so this patch always
enables it.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- A couple mxs boards that run I2C at 400 kHz experience some unstable
issue occasionally. Slow down the clock speed to have I2C work
reliably.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRXCXBAAoJEFBXWFqHsHzOqg4H/irUyWQkIfch7us/vnMQnntr
y67TFoq1ucfHDA4/Okd5YxeUWjh0vaFJTVu5JLKfuT7HGTzSeqG4sFCp/A6/i9F9
ZGbcmTUSgG3erjpzN0R+PLxWO5iqjT8Mg3/cyK83SguKtf4u/MVJq8jpTyc0JJ9R
UNj4OaKN5n7tvPGAkj8ypWDpQwlczRRie6v+Nt1qWP1K7T7Ez9ZMkhOvd7WLUi4T
H7HcWo5IOUBzLvf7JmBAQwTCTdl7BJglBO5FjTn7ao0uaMEHLJOwzPWdXs08Agzh
qMVJcWqVCcQQmB5nuDDb08mlXXEYrt/92qL3LUejJaX76bPH+lzfCnvrDGUIuvo=
=Towm
-----END PGP SIGNATURE-----
Merge tag 'mxs-fixes-3.9-4' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The mxs fixes for 3.9, take 4:
- A couple mxs boards that run I2C at 400 kHz experience some unstable
issue occasionally. Slow down the clock speed to have I2C work
reliably.
* tag 'mxs-fixes-3.9-4' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: Slow down the I2C clock speed
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull ARM fixes from Russell King:
"Another round of ARM fixes, which include:
- Fixing a problem with LPAE mapping sections
- Reporting of some hwcaps on Krait CPUs
- Avoiding repetitive warnings in the breakpoint code
- Fixing a build error noticed on Dove platforms with PJ4 CPUs
- Fix masking of level 2 cache revision.
- Fixing timer-based udelay()
- A larger fix for an erratum causing people major grief with Cortex
A15 CPUs"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7690/1: mm: fix CONFIG_LPAE typos
ARM: 7689/1: add unwind annotations to ftrace asm
ARM: 7685/1: delay: use private ticks_per_jiffy field for timer-based delay ops
ARM: 7684/1: errata: Workaround for Cortex-A15 erratum 798181 (TLBI/DSB operations)
ARM: 7682/1: cache-l2x0: fix masking of RTL revision numbering and set_debug init
ARM: iWMMXt: always enable iWMMXt support with PJ4 CPUs
ARM: 7681/1: hw_breakpoint: use warn_once to avoid spam from reset_ctrl_regs()
ARM: 7678/1: Work around faulty ISAR0 register in some Krait CPUs
ARM: 7680/1: Detect support for SDIV/UDIV from ISAR0 register
ARM: 7679/1: Clear IDIVT hwcap if CONFIG_ARM_THUMB=n
ARM: 7677/1: LPAE: Fix mapping in alloc_init_section for unaligned addresses
ARM: KVM: vgic: take distributor lock on sync_hwstate path
ARM: KVM: vgic: force EOIed LRs to the empty state
CONFIG_LPAE doesn't exist: the correct option is CONFIG_ARM_LPAE, so fix
up the two typos under arch/arm/.
The fix to head.S is slightly scary, but this is just for setting up
an early io-mapping for the serial port when running on a big-endian,
LPAE system. Since these systems don't exist in the wild (at least, I
have no access to one outside of kvmtool, which doesn't provide a serial
port suitable for earlyprintk), then we can revisit the code later if it
causes any problems.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add unwind annotations to the ftrace assembly code so that the function
tracer's stacktracing options (func_stack_trace, etc.) work when
CONFIG_ARM_UNWIND is enabled.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 70264367a2 ("ARM: 7653/2: do not scale loops_per_jiffy when
using a constant delay clock") fixed a problem with our timer-based
delay loop, where loops_per_jiffy is scaled by cpufreq yet used directly
by the timer delay ops.
This patch fixes the problem in a more elegant way by keeping a private
ticks_per_jiffy field in the delay ops, independent of loops_per_jiffy
and therefore not subject to scaling. The loop-based delay continues to
use loops_per_jiffy directly, as it should.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On Cortex-A15 (r0p0..r3p2) the TLBI/DSB are not adequately shooting down
all use of the old entries. This patch implements the erratum workaround
which consists of:
1. Dummy TLBIMVAIS and DSB on the CPU doing the TLBI operation.
2. Send IPI to the CPUs that are running the same mm (and ASID) as the
one being invalidated (or all the online CPUs for global pages).
3. CPU receiving the IPI executes a DMB and CLREX (part of the exception
return code already).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit b8db6b8 (ARM: 7547/4: cache-l2x0: add support for Aurora L2 cache
ctrl) moved the masking of the part ID which caused the RTL version to be
lost. Commit 6248d06 (ARM: 7545/1: cache-l2x0: make outer_cache_fns a
field of l2x0_of_data) changed how .set_debug is initialized. Both commits
break commit 74ddcdb (ARM: 7608/1: l2x0: Only set .set_debug
on PL310 r3p0 and earlier) which uses the RTL version to conditionally set
.set_debug function pointer. Commit b8db6b8 also caused the printed cache
ID to be missing the version information.
Fix this by reverting how the part number is masked so the RTL version
info is maintained. The cache-id-part DT property does not set the RTL
bits so masking them should have no effect. Also, re-arrange the order
of the function pointer init so the .set_debug function can be overridden.
Reported-by: Paolo Pisati <paolo.pisati@canonical.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jason Cooper reports these build errors:
arch/arm/kernel/built-in.o: In function `iwmmxt_do':
/.../arch/arm/kernel/pj4-cp0.c:36: undefined reference to `iwmmxt_task_release'
/.../arch/arm/kernel/pj4-cp0.c:40: undefined reference to `iwmmxt_task_switch'
make: *** [vmlinux] Error 1
This is caused because the PJ4 code explicitly references the iWMMXt
code, but doesn't require it to be built. Fix this by ensuring that
iWMMXt is always enabled with PJ4.
Reported-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Slow down the I2C clock speed on M28 and SPS1 as it turns out the
I2C block in i.MX28 can not operate stable enough with the bus
running at 400kHz. Note that the driver used by Freescale runs
the bus at 250kHz when 400kHz speed is selected, but the mainline
Linux kernel runs the bus at actual 400kHz and that's where it is
occasionally unstable. Play safe and run the bus at 100kHz.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
After a quiet set of fixes for 3.9-rc4, a lot of people woke up and sent
urgent fixes for 3.9. I pushed back on a number of them that got
deferred to 3.10, but these are the ones that seemed important.
Regression in 3.9:
- Multiple regressions in OMAP2+ clock cleanup
- SH-Mobile frame buffer bug fix that merged here because of maintainer MIA
- ux500 prcmu changes broke DT booting
- MMCI duplicated regulator setup on ux500
- New ux500 clock driver broke ethernet on snowball
- Local interrupt driver for mvebu broke ethernet
- MVEBU GPIO driver did not get set up right on Orion DT
- incorrect interrupt number on Orion crypto for DT
Long-standing bugs, including candidates for stable:
- Kirkwood MMC needs to disable invalid card detect pins
- MV SDIO pinmux was wrong on Mirabox
- GoFlex Net board file needs to set NAND chip delay
- MSM timer restart race
- ep93xx early debug code broke in 3.7
- i.MX CPU hotplug race
- Incorrect clock setup for OMAP1 USB
- Workaround for bad clock setup by some old OMAP4 boot loaders
- Static I/O mappings on cns3xxx since 3.2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=oQbL
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Arnd Bergmann:
"After a quiet set of fixes for 3.9-rc4, a lot of people woke up and
sent urgent fixes for 3.9. I pushed back on a number of them that got
deferred to 3.10, but these are the ones that seemed important.
Regression in 3.9:
- Multiple regressions in OMAP2+ clock cleanup
- SH-Mobile frame buffer bug fix that merged here because of
maintainer MIA
- ux500 prcmu changes broke DT booting
- MMCI duplicated regulator setup on ux500
- New ux500 clock driver broke ethernet on snowball
- Local interrupt driver for mvebu broke ethernet
- MVEBU GPIO driver did not get set up right on Orion DT
- incorrect interrupt number on Orion crypto for DT
Long-standing bugs, including candidates for stable:
- Kirkwood MMC needs to disable invalid card detect pins
- MV SDIO pinmux was wrong on Mirabox
- GoFlex Net board file needs to set NAND chip delay
- MSM timer restart race
- ep93xx early debug code broke in 3.7
- i.MX CPU hotplug race
- Incorrect clock setup for OMAP1 USB
- Workaround for bad clock setup by some old OMAP4 boot loaders
- Static I/O mappings on cns3xxx since 3.2"
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: cns3xxx: fix mapping of private memory region
arm: mvebu: Fix pinctrl for Armada 370 Mirabox SDIO port.
arm: orion5x: correct IRQ used in dtsi for mv_cesa
arm: orion5x: fix orion5x.dtsi gpio parameters
ARM: Kirkwood: fix unused mvsdio gpio pins
arm: mvebu: Use local interrupt only for the timer 0
ARM: kirkwood: Fix chip-delay for GoFlex Net
ARM: ux500: Enable the clock controlling Ethernet on Snowball
ARM: ux500: Stop passing ios_handler() as an MMCI power controlling call-back
ARM: ux500: Apply the TCPM and TCDM locations and sizes to dbx5x0 DT
fbdev: sh_mobile_lcdc: fixup B side hsync adjust settings
ARM: OMAP: clocks: Delay clk inits atleast until slab is initialized
ARM: imx: fix sync issue between imx_cpu_die and imx_cpu_kill
ARM: msm: Stop counting before reprogramming clockevent
ARM: ep93xx: Fix wait for UART FIFO to be empty
ARM: OMAP4: PM: fix PM regression introduced by recent clock cleanup
ARM: OMAP3: hwmod data: keep MIDLEMODE in force-standby for musb
ARM: OMAP4: clock data: lock USB DPLL on boot
ARM: OMAP1: fix USB host on 1710
From Anton Vorontsov <anton@enomsg.org>:
This tag includes Mac Lin's work to revive CNS3xxx booting:
"Since commit 0536bdf33f (ARM: move iotable mappings within the vmalloc
region), [...] the pre-defined iotable mappings is not in the vmalloc
region. [...] move the iotable mappings into the vmalloc region, and
merge the MPCore private memory region (containing the SCU, the GIC and
the TWD) as a single region."
Plus there is a small cosmetic fix, also from Mac Lin.
* tag 'v3.9-rc1_cns3xxx_fixes' of git://git.infradead.org/users/cbou/linux-cns3xxx:
ARM: cns3xxx: fix mapping of private memory region
[arnd: dropped the cosmetic fix from the merge as it is not needed for 3.9]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In the conversion to pinctrl, an error in the pins for the rebuild
LED was introduced. This patch assigns the correct pins and includes
the correct name for the LED in kirkwood-iomega_ix2_200.dts.
Signed-off-by: Nigel Roberts <nigel@nobiscuit.com>
Cc: <stable@vger.kernel.org> # v3.8.x
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Since commit 0536bdf33f (ARM: move iotable mappings within the vmalloc
region), the Cavium CNS3xxx cannot boot anymore.
This is caused by the pre-defined iotable mappings is not in the vmalloc
region. This patch move the iotable mappings into the vmalloc region, and
merge the MPCore private memory region (containing the SCU, the GIC and
the TWD) as a single region.
Signed-off-by: Mac Lin <mkl0301@gmail.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Cc: stable@vger.kernel.org [v3.3+]
- mvebu
- interrupt fix
- DT pinctrl definition for sdio
- kirkwood
- chip-delay for GoFlex Net (fix reading nand)
- set mvsdio unused pins to invalid value for legacy boards (0 is valid)
- orion5x
- fix typo in gpio parameters
- use correct irq in dtsi
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRVIcVAAoJEAi3KVZQDZAev1wH/0oIYEZvAeE8Nh49bn7EKgwH
ef44bin9g/JkEZ/3YndUE+1wqq/4nBaJN2IWGsPmbKGZFWNaoaPG1gFr0VsOepge
GpKdwrxUMAgIzLO+4FtN85Zy3Qe4Jn8YWjJcZXZbl404cyQx5bDID0clYsn0m2jW
F6nWva5ULAbWNBsUpRQ3h8nYfKi9QsWvhOgFxsaAiR3VCpLOk+MKK7Y0cwqpi60K
p2ALUultfXGckqJyFCoZNHwN52dlllsXD09i/lRzM91nT/VEPzwWNhPcoNjwiQwu
qfloTU97Lfq7168G4PTSEq8V7LP/NLbAlwwJ3VW3HCrtVTefSQFdUF9EA9bjl8I=
=EExD
-----END PGP SIGNATURE-----
Merge tag 'mvebu_fixes_for_v3.9_round2' of git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper <jason@lakedaemon.net>:
mvebu fixes for v3.9 (round 2)
- mvebu
- interrupt fix
- DT pinctrl definition for sdio
- kirkwood
- chip-delay for GoFlex Net (fix reading nand)
- set mvsdio unused pins to invalid value for legacy boards (0 is valid)
- orion5x
- fix typo in gpio parameters
- use correct irq in dtsi
* tag 'mvebu_fixes_for_v3.9_round2' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: Fix pinctrl for Armada 370 Mirabox SDIO port.
arm: orion5x: correct IRQ used in dtsi for mv_cesa
arm: orion5x: fix orion5x.dtsi gpio parameters
ARM: Kirkwood: fix unused mvsdio gpio pins
arm: mvebu: Use local interrupt only for the timer 0
ARM: kirkwood: Fix chip-delay for GoFlex Net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The previous configuration used the wrong "clk" pin. Without this
change mv_sdio worked because the bootloader would set the pin up, but
with a bootloader that does not set the pin, mv_sdio fails to detect any
card.
I have tested this change using a mwifiex_sdio wireless network adapter
over the SDIO interface.
Signed-off-by: Ryan Press <ryan@presslab.us>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The crypto functionality in the orion5x dtsi uses the Ethernet IRQ and
so things do not work and there is much grumbling at boot time.
The IRQ for the crypto should be 28, and not 22, and that is what this
patch corrects.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
orion5x.dtsi is missing the gpio alias as well as including a typo
('ngpio' instead of 'ngpios') that prevented the orion-gpio driver
from loading. Also missing were the interrupt-controller properties.
This patches resolves those glitches.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
mvsdio_platform_data allows to pass card detect and write protect gpio
numbers to the driver. Some kirkwood boards don't use both pins as they
are not connected, and don't set the corresponding value in platform_data.
This will leave the unset values in platform_data initialized as 0, which
is in fact a valid gpio pin. mvsdio will grab that pin and configure it as
gpio, which in turn breaks nand controller as mpp0 also carries nand_io2.
This patch fixes the above by initializing unused gpio functions in the
platform_data with an invalid (-1) value.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reported-by: Soeren Moch <smoch@web.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The commit 3a6f08a37 "arm: mvebu: Add support for local interrupt",
managed the 28th first interrupts as local interrupt to match the
hardware specification. Among these interrupts there are the Gigabits
Ethernet ones used by the mvneta driver. Unfortunately the state of
the percpu_irq API prevents the driver to use it.
Indeed the interrupts have to be freed when the .stop() function is
called. As the free_percpu_irq() function don't disable the interrupt
line, we have to do it on each CPU before calling this. The function
disable_percpu_irq() only disable the percpu on the current CPU and
there is no function which allows to disable a percpu irq on a given
CPU. Waiting for the extension of the percpu_irq API, this fix allows
to use again the mvneta driver.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This fixes "Too few good blocks within range" issues on GoFlex Net by setting
chip-delay to 40.
The basic problem was discussed at http://forum.doozan.com/read.php?2,7451
Signed-off-by: Eric Hutter <hutter.eric@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: <stable@vger.kernel.org> # v3.6.x
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
From Ryan Mallon <rmallon@gmail.com>:
It is a regression fix for some ep93xx boards which are failing to boot
on current mainline. The patch has been tested in next over the last
few days.
* tag 'ep93xx-fixes-for-3.9-rc5' of git://github.com/RyanMallon/linux-ep93xx:
ARM: ep93xx: Fix wait for UART FIFO to be empty
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Running suspend/resume without no_console_suspend setting on kernel
cmdline will likely makes system hang. It causesd by the sync issue
between imx_cpu_die() and imx_cpu_kill() call. Fix the issue by
synchronizing the calls using cpu jumping argument register which is
free to use in kernel.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRU60+AAoJEFBXWFqHsHzOTzAIAL0t34b0Pd1FRuybb8q1uwGJ
Xe7gr/knRLszQ6FemX4F2qqU3Xdx2OLjET6iZT1j1pcO2WOUB93C0Pa6hwZ7u8ex
4EMgBiwaEqnr8ICkPMEQIrJ/ja8VIazYwgFDk3MDV4djIDPEdl6CZz9BOWXSce8M
f9o8YhmVvV5TINz9TxOKNA19qxjxqR8K/WT3DsiTxmo7660rtMO4VNhPFhRLMRlm
8qd0SSZ9XYNa05aJdXa+YayCpm6SGdcSj6fWrpDmQ4926D9dhvX/TEDNqmibfUyw
7YAyk2p1U8W5+20nUrYDjZnfBzLgaTFg60Y60DrYbcOPk7ZlqRgGk0SyIjGwyjw=
=V81t
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.9-4' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The imx fixes for 3.9, take 4:
Running suspend/resume without no_console_suspend setting on kernel
cmdline will likely makes system hang. It causesd by the sync issue
between imx_cpu_die() and imx_cpu_kill() call. Fix the issue by
synchronizing the calls using cpu jumping argument register which is
free to use in kernel.
* tag 'imx-fixes-3.9-4' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: fix sync issue between imx_cpu_die and imx_cpu_kill
ARM: imx: add dependency check for DEBUG_IMX_UART_PORT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Get TCPM and TCDM locations from the device tree
- Skip passing the ios_handler for the MMCI
- Enable the ethernet clock for Snowball
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=v6nX
-----END PGP SIGNATURE-----
Merge tag 'ux500-fixes-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij <linus.walleij@stericsson.com>:
Fixes boot regressions on Device Tree:
- Get TCPM and TCDM locations from the device tree
- Skip passing the ios_handler for the MMCI
- Enable the ethernet clock for Snowball
* tag 'ux500-fixes-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Enable the clock controlling Ethernet on Snowball
ARM: ux500: Stop passing ios_handler() as an MMCI power controlling call-back
ARM: ux500: Apply the TCPM and TCDM locations and sizes to dbx5x0 DT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This fixes a regression introduced by common clk enablement.
On some u8500 based boards, the FMSC clock which is usually used
for flash, is wired up to the SMSC911x Ethernet driver. However,
the SMSC911x doesn't have common clk support yet, rendering it
unusable. Prior to the introduction of common clk the FMSC clock
was default on; however, common clk disables all clocks by default
and insists drivers take responsibility to enable theirs.
This fix enables the FMSC clock on Snowball, subsequently turning
on the SMSC911x Ethernet chip. It will be removed when the driver
is compatible with common clk.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes a regression introduced during the v3.9 merge window.
Now MMCI on/off functionality is using the regulator framework
from the MMCI driver, if we provide the ios_handler call-back we
essentially duplicate functionality, which causes a large mess
and lots of booting issues.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes a regression introduced by commit:
05ec260 mfd:db8500-prcmu: update resource passing
All DBx5x0 based SoCs have access to two Tightly Coupled Memory
(TCM) locations based on the PRCMU itself. One area from program
memory (TCPM) and one for data memory (TCDM). The PRCMU needs to
know where these are in order to function correctly. However,
these are currently passed though platform device resources, which
can only be obtained if Device Tree booting isn't in use. Thus we
must also support them in DT by supplying them through the PRCMU
node.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
conversion, and few USB regression fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=DYTR
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.9-rc3/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren <tony@atomide.com>:
A clock regression fix that happened with the common clock
conversion, and few USB regression fixes.
* tag 'omap-for-v3.9-rc3/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: clocks: Delay clk inits atleast until slab is initialized
ARM: OMAP4: PM: fix PM regression introduced by recent clock cleanup
ARM: OMAP3: hwmod data: keep MIDLEMODE in force-standby for musb
ARM: OMAP4: clock data: lock USB DPLL on boot
ARM: OMAP1: fix USB host on 1710
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
clk inits on OMAP happen quite early, even before slab is available.
The dependency comes from the fact that the timer init code starts to
use clocks and hwmod and we need clocks to be initialized by then.
There are various problems doing clk inits this early, one is,
not being able to do dynamic clk registrations and hence the
dependency on clk-private.h. The other is, inability to debug
early kernel crashes without enabling DEBUG_LL and earlyprintk.
Doing early clk init also exposed another instance of a kernel
panic due to a BUG() when CONFIG_DEBUG_SLAB is enabled.
[ 0.000000] Kernel BUG at c01174f8 [verbose debug info unavailable]
[ 0.000000] Internal error: Oops - BUG: 0 [#1] SMP ARM
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 Not tainted (3.9.0-rc1-12179-g72d48f9 #6)
[ 0.000000] PC is at __kmalloc+0x1d4/0x248
[ 0.000000] LR is at __clk_init+0x2e0/0x364
[ 0.000000] pc : [<c01174f8>] lr : [<c0441f54>] psr: 600001d3
[ 0.000000] sp : c076ff28 ip : c065cefc fp : c0441f54
[ 0.000000] r10: 0000001c r9 : 000080d0 r8 : c076ffd4
[ 0.000000] r7 : c074b578 r6 : c0794d88 r5 : 00000040 r4 : 00000000
[ 0.000000] r3 : 00000000 r2 : c07cac70 r1 : 000080d0 r0 : 0000001c
[ 0.000000] Flags: nZCv IRQs off FIQs off Mode SVC_32 ISA ARM Segment kernel
[ 0.000000] Control: 10c53c7d Table: 8000404a DAC: 00000017
[ 0.000000] Process swapper (pid: 0, stack limit = 0xc076e240)
[ 0.000000] Stack: (0xc076ff28 to 0xc0770000)
[ 0.000000] ff20: 22222222 c0794ec8 c06546e8 00000000 00000040 c0794d88
[ 0.000000] ff40: c074b578 c076ffd4 c07951c8 c076e000 00000000 c0441f54 c074b578 c076ffd4
[ 0.000000] ff60: c0793828 00000040 c0794d88 c074b578 c076ffd4 c0776900 c076e000 c07272ac
[ 0.000000] ff80: 2f800000 c074c968 c07f93d0 c0719780 c076ffa0 c076ff98 00000000 00000000
[ 0.000000] ffa0: 00000000 00000000 00000000 00000001 c074cd6c c077b1ec 8000406a c0715724
[ 0.000000] ffc0: 00000000 00000000 00000000 00000000 00000000 c074c968 10c53c7d c0776974
[ 0.000000] ffe0: c074cd6c c077b1ec 8000406a 411fc092 00000000 80008074 00000000 00000000
[ 0.000000] [<c01174f8>] (__kmalloc+0x1d4/0x248) from [<c0441f54>] (__clk_init+0x2e0/0x364)
[ 0.000000] [<c0441f54>] (__clk_init+0x2e0/0x364) from [<c07272ac>] (omap4xxx_clk_init+0xbc/0x140)
[ 0.000000] [<c07272ac>] (omap4xxx_clk_init+0xbc/0x140) from [<c0719780>] (setup_arch+0x15c/0x284)
[ 0.000000] [<c0719780>] (setup_arch+0x15c/0x284) from [<c0715724>] (start_kernel+0x7c/0x334)
[ 0.000000] [<c0715724>] (start_kernel+0x7c/0x334) from [<80008074>] (0x80008074)
[ 0.000000] Code: e5883004 e1a00006 e28dd00c e8bd8ff0 (e7f001f2)
[ 0.000000] ---[ end trace 1b75b31a2719ed1c ]---
[ 0.000000] Kernel panic - not syncing: Attempted to kill the idle task!
It was a know issue, that slab allocations would fail when common
clock core tries to cache parent pointers for mux clocks on OMAP,
and hence a patch 'clk: Allow late cache allocation for clk->parents,
commit 7975059d' was added to work this problem around.
A BUG() within kmalloc() with CONFIG_DEBUG_SLAB enabled was completely
overlooked causing this regression.
More details on the issue reported can be found here,
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg85932.html
With all these issues around clk inits happening way too early, it
makes sense to at least move them to a point where dynamic memory
allocations are possible. So move them to a point just before the
timer code starts using clocks and hwmod.
This should at least pave way for clk inits on OMAP moving to dynamic
clock registrations instead of using the static macros defined in
clk-private.h.
The issue with kernel panic while CONFIG_DEBUG_SLAB is enabled
was reported by Piotr Haber and Tony Lindgren and this patch
fixes the reported issue as well.
Reported-by: Piotr Haber <phaber@broadcom.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
Cc: stable@vger.kernel.org # v3.8
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is a sync issue with hotplug operation. It's possible that when
imx_cpu_kill gets running on primary core, the imx_cpu_die execution
on the core which is to be killed hasn't been finished yet. The problem
will very likely be hit when running suspend without no_console_suspend
setting on kernel cmdline.
It uses cpu jumping argument register to sync imx_cpu_die and
imx_cpu_kill. The register will be set in imx_cpu_die and imx_cpu_kill
will wait for the register being cleared to actually kill the cpu.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
that cause system hangs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=xMpr
-----END PGP SIGNATURE-----
Merge tag 'msm-fix-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into fixes
From David Brown <davidb@codeaurora.org>:
This fix is intended for v3.9. It fixes a timer bug on MSM targets
that cause system hangs.
* tag 'msm-fix-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Stop counting before reprogramming clockevent
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Four patches for arm-soc this week:
- Kevin Hilman is no longer reachable under his previous email address.
He submitted the patch earlier, but nobody felt responsible to pick
it up.
- One Tegra fix for an incorect register address in device tree.
- IMX multiplatform support exposes a configuration option that
leads to unbootable kernels on all other machines and that needs
to depend on that platform.
- A nontrivial bug fix for the setup of the mxs video output.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F6UW
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Arnd Bergmann:
"Four patches for arm-soc this week:
- Kevin Hilman is no longer reachable under his previous email
address. He submitted the patch earlier, but nobody felt
responsible to pick it up.
- One Tegra fix for an incorect register address in device tree.
- IMX multiplatform support exposes a configuration option that leads
to unbootable kernels on all other machines and that needs to
depend on that platform.
- A nontrivial bug fix for the setup of the mxs video output."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: update email address for Kevin Hilman
ARM: tegra: fix register address of slink controller
ARM: imx: add dependency check for DEBUG_IMX_UART_PORT
ARM: video: mxs: Fix mxsfb misconfiguring VDCTRL0
Fix typo on register address of slink3 controller where register
address is wrongly set as 0x7000d480 but it is 0x7000d800.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
If the clockevent is forcibly reprogrammed to have a different
match value we mistakenly assume the timer is not ticking and
program a new match value while the timer is running. Although we
clear the timer before programming a new match, it's better to
stop the timer before clearing it so that we're sure the proper
amount of ticks are counted. Failure to do so can lead to missed
ticks and system hangs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
CPU debug features like hardware break, watchpoints can be used only
when the debug mode is enabled and available. Unfortunately on OMAP4
based devices, after a CPU power cycle, the debug feature gets disabled
which leads to a flood of messages coming from reset_ctrl_regs() which
gets called on every CPU_PM_EXIT with CPUidle enabled.
So make use of warn_once() so that system is usable.
Thanks to Will for pointers and Lokesh for the analysis of the issue.
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some early versions of the Krait CPU design incorrectly indicate
that they only support the UDIV and SDIV instructions in Thumb
mode when they actually support them in ARM and Thumb mode. It
seems that these CPUs follow the DDI0406B ARM ARM which has two
possible values for the divide instructions field, instead of the
DDI0406C document which has three possible values.
Work around this problem by checking the MIDR against Krait CPUs
with this faulty ISAR0 register and force the hwcaps to indicate
support in both modes.
[sboyd: Rewrote commit text to reflect real reasoning now that
we autodetect udiv/sdiv]
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ISAR0 register indicates support for the SDIV and UDIV
instructions in both the Thumb and ARM instruction set. Read the
register to detect the supported instructions and update the
elf_hwcap mask as appropriate. This is better than adding more
and more cpuid checks in proc-v7.S for each new cpu variant that
supports these instructions.
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Don't advertise support for the SDIV/UDIV thumb instructions if
the kernel is not compiled with support for thumb userspace. This
is in line with how we remove the THUMB hwcap in these
configurations.
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With LPAE enabled, alloc_init_section() does not map the entire
address space for unaligned addresses.
The issue also reproduced with CMA + LPAE. CMA tries to map 16MB
with page granularity mappings during boot. alloc_init_pte()
is called and out of 16MB, only 2MB gets mapped and rest remains
unaccessible.
Because of this OMAP5 boot is broken with CMA + LPAE enabled.
Fix the issue by ensuring that the entire addresses are
mapped.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoffer Dall <chris@cloudcar.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Laura Abbott <lauraa@codeaurora.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Christoffer Dall <chris@cloudcar.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Arnd Bergmann
Gregory CLEMENT
Nigel Roberts
Sylwester Nawrocki
Dirk Behme
Shawn Guo
Markus Pargmann
Linus Torvalds
Paul Bolle
Rabin Vincent
Will Deacon
Catalin Marinas
Rob Herring
Russell King
Marek Vasut
Mac Lin
Ryan Press
Alexander Clouter
Sebastian Hesselbarth
Eric Hutter
Lee Jones
Rajendra Nayak
Laxman Dewangan
Stephen Boyd
Santosh Shilimkar
Stepan Moskovchenko
Sricharan R