Add flag value UPF_FIXED_TYPE which specifies that the UART type is
known and should not be probed. For this case the UARTs properties
are just copied out of the uart_config entry.
This allows us to keep SOC specific 8250 probe code out of 8250.c. In
this case we know the serial hardware will not be changing as it is on
the same silicon as the CPU, and we can specify it with certainty in
the board/cpu setup code.
The alternative is to load up 8250.c with a bunch of OCTEON specific
special cases in the probing code.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to use Cavium OCTEON specific serial i/o drivers, we first
patch the 8250 driver to use replaceable I/O functions. Compatible
I/O functions are added for existing iotypeS.
An added benefit of this change is that it makes it easy to factor
some of the existing special cases out to board/SOC specific support
code.
The alternative is to load up 8250.c with a bunch of OCTEON specific
iotype code and bug work-arounds.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In serial8250_isa_init_ports(), the port's lock is initialized. We
should not overwrite it. In early_serial_setup(), only copy in the
fields we need. Since the early console code only uses a subset of
the fields, these are sufficient.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the tty_port and uart_info bits around a little. By embedding the uart_info
into the uart_port we get rid of lots of corner case testing and also get the
ability to go port<->state<->info which is a bit more elegant than the current
data structures.
Downsides - we allocate a tiny bit more memory for unused ports, upside we've
removed as much code as it saved for most users..
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We don't need the BKL here any more so it can go. In a couple of spots the
driver requirements are not clear so push the lock down into the driver.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the tty port operations, add refcounting, and refactor a bit to make the
refcounting work cleanly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now we have our ducks in order we can begin switching to the port
operations
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We will need this kref fitted to make full use of the port operations.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to this ready for using the standard helpers
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now the locking is straight and the port kref usage is straight we can
replace lots of chunks of code with the standard port helpers
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Makes TIOCM ioctls for Data Carrier Detect & related functions
work like /drivers/serial/serial-core.c potentially needed
for pppd & similar user programs.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Init the tty structure once
Don't set ->low_latency twice in a row
Don't force bits we should be leaving to the user
Don't allocate termios arrays as these are in fact allocated by the tty layer
for you and just overwrite the ones allocated in the driver
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Checking tty == NULL doesn't help us unless we have a clear semantic for
the locking of the tty object in the driver. Use the tty kref objects so that
we can take references to the tty in the USB event handling paths.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The write wakeup is done anyway for the poll while DO_WRITE_WAKUP is
cleared, set and managed by the ldisc layer and is no business of the pty
code.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The N_TTY ldisc layer does not send SIGIO POLL_OUTs correctly when output is
possible due to flawed handling of the TTY_DO_WRITE_WAKEUP bit. It will
either send no SIGIOs at all or on every tty wakeup.
The fix is to set the bit when the tty driver write would block and test
and clear it on write wakeup.
[Merged with existing N_TTY patches and a small buglet fixed -- Alan]
Signed-off-by: Thomas Pfaff <tpfaff@pcs.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The underlying problem is that the device methods don't all correctly
handle disconnected status and some keep reporting bytes pending which
causes tcdrain to stall.
When the cable is unplugged they are definitely gone, and as this is true
for all USB cables we can fix it in the core usb serial code.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PCI-card identified as "Oxford Semiconductor Ltd EXSYS EX-41092 Dual
16950 Serial adapter" is only usable with other devices (i.e. not the same
card) after doing a "setserial /dev/ttyS<n> baud_base 115200". This
baud_base should be default for this card.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Again this is a lot of common code we can unify
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we have no speed set at some point then we should not raise DTR/RTS at
that point when opening as the tty is not ready
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Start sucking more commonality out of the drivers into a single piece of
core code.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Normalise them so we can use the common helpers later on
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch generic_serial to do port count locking via the tty_port structure
ready for moving to a common port wait routine. Keep the old driver lock for
internal calling so we don't risk messing up the drivers below until we
are ready.
Still needs kref conversions
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This helps set the basis for moving block_til_ready into common code. We also
introduce a tty_port_hangup helper as this will also be generally needed.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This moves another per device special out of what should be shared open
wait paths into private methods
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was an alloc/clear wrapper but makes even less sense now it uses
kzalloc. Kill it off.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the first step to generalising the various pieces of waiting logic
duplicated in all sorts of serial drivers.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add device funtion for usb serial console, so we can open /dev/console
when we use a usb serial device as console.
(Typecast removed as noted by Sergei Shtylyov)
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
this happening again by making use of 'const'.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
scribble on its own reference structures.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
USB serial has always had races where the tty port usage count can hit zero
during a receive event. The internal locking is a mutex so we can't use
that in the IRQ handlers.
With krefs we can tackle this differently but we still need to be careful.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch causes "bell" (^G) characters (invoked when the input buffer
is full) to be immediately output rather than filling the echo buffer.
This is especially a problem when the tty is stopped and buffers fill, since
the bells do not serve their purpose of immediate notification that the
buffer cannot take further input, and they will flush all at once when the
tty is restarted.
Signed-off-by: Joe Peterson <joe@skyrush.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the handling of input characters when the tty buffer is full or nearly
full. This includes tests that are done in n_tty_receive_char() and handling
of PARMRK.
Problems with the buffer-full tests done in receive_char() caused characters to
be lost at times when the buffer(s) filled. Also, these full conditions
would often only be detected with echo on, and PARMRK was not accounted for
properly in all cases. One symptom of these problems, in addition to lost
characters, was early termination from unix commands like tr and cat when
^Q was used to break from a stopped tty with full buffers (note that breaking
out was often previously not possible, due to the pty getting in "gridlock",
which will be addressed in another patch). Note space is always reserved
at the end of the buffer for a newline (or EOF/EOL) in canonical mode.
Signed-off-by: Joe Peterson <joe@skyrush.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix process_output_block to detect continuation characters correctly
and to handle control characters even when O_OLCUC is enabled. Make
similar change to do_output_char().
Signed-off-by: Joe Peterson <joe@skyrush.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have special case logic for resizing pty/tty pairs. We also have a per
driver resize method so for the pty case we should use it.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixed sparse warning:
drivers/char/tty_io.c:1216:19: warning: symbol 'tty_driver_lookup_tty' was not declared. Should it be static?
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
