Commit Graph

118 Commits

Author SHA1 Message Date
Dan Williams a06d568f7c async_xor: dma_map destination DMA_BIDIRECTIONAL
Mapping the destination multiple times is a misuse of the dma-api.
Since the destination may be reused as a source, ensure that it is only
mapped once and that it is mapped bidirectionally.  This appears to add
ugliness on the unmap side in that it always reads back the destination
address from the descriptor, but gcc can determine that dma_unmap is a
nop and not emit the code that calculates its arguments.

Cc: <stable@kernel.org>
Cc: Saeed Bishara <saeed@marvell.com>
Acked-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-12-08 13:46:00 -07:00
Dan Williams b0b42b16ff dmaengine: protect 'id' from concurrent registrations
There is a possibility to have two devices registered with the same id.

Cc: <stable@kernel.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-12-03 17:25:36 -07:00
Dan Williams 532d3b1f86 ioat: wait for self-test completion
As part of the ioat_dma self-test it performs a printk from a completion
callback.  Depending on the system console configuration this output can
take longer than a millisecond causing the self-test to fail.  Introduce a
completion with a generous timeout to mitigate this failure.

Cc: <stable@kernel.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-12-03 17:16:55 -07:00
Kay Sievers 06190d8415 dmaengine: struct device - replace bus_id with dev_name(), dev_set_name()
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-11-11 13:12:33 -07:00
Dan Williams 65e503814d iop-adma: use iop_paranoia() for debug BUG_ONs
Now that the critical read back to flush the next descriptor address is
fixed we can downgrade some BUG_ONs that need only be enabled when testing
changes to the driver.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-11-11 13:12:33 -07:00
Dan Williams 137cb55c6d iop-adma: add a dummy read to flush next descriptor update
The current dummy read references the wrong address allowing the next
descriptor address update to linger in the store buffer and get passed
by an 'append' event.

This issue was uncovered by the change from strongly-ordered to device
memory for the adma registers.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-11-11 13:12:33 -07:00
Maciej Sosnowski 12ccea24e3 [3/4] I/OAT: fix async_tx.callback checking
async_tx.callback should be checked for the first
not the last descriptor in the chain.

Cc: <stable@kernel.org>
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-10 15:01:00 -08:00
Maciej Sosnowski c2c0b4c543 [2/4] I/OAT: fix dma_pin_iovec_pages() error handling
Error handling needs to be modified in dma_pin_iovec_pages().
It should return NULL instead of ERR_PTR
(pinned_list is checked for NULL in tcp_recvmsg() to determine
if iovec pages have been successfully pinned down).
In case of error for the first iovec,
local_list->nr_iovecs needs to be initialized.

Cc: <stable@kernel.org>
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-10 15:00:56 -08:00
Maciej Sosnowski c3d4f44f50 [1/4] I/OAT: fix channel resources free for not allocated channels
If the ioatdma driver is loaded but not used it does not allocate descriptors.
Before it frees channel resources it should first be sure
that they have been previously allocated.

Cc: <stable@kernel.org>
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Tested-by: Tom Picard <tom.s.picard@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-10 15:00:51 -08:00
Len Brown 9fb3c5ca3d Merge branch 'i7300_idle' into release 2008-10-25 04:07:44 -04:00
Venki Pallipadi f371be6352 i7300_idle: Fix compile warning CONFIG_I7300_IDLE_IOAT_CHANNEL not defined
When I7300_idle driver is not configured, there is a compile time
warning about IDLE_IOAT_CHANNEL not defined. Fix it.

Reported-by: Suresh Siddha <suresh.b.siddha@intel.com>
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-24 12:59:47 -04:00
Venki Pallipadi 3ad0b02e4c i7300_idle: Disable ioat channel only on platforms where ile driver can load
Based on input from Andi Kleen:
share the platform detection code with ioat_dma and disable the channel in
dma engine only for specific platforms.

Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-24 12:54:18 -04:00
Len Brown 057316cc6a Merge branch 'linus' into test
Conflicts:
	MAINTAINERS
	arch/x86/kernel/acpi/boot.c
	arch/x86/kernel/acpi/sleep.c
	drivers/acpi/Kconfig
	drivers/pnp/Makefile
	drivers/pnp/quirks.c

Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-23 00:11:07 -04:00
Andy Henroid 27471fdb32 i7300_idle driver v1.55
The Intel 7300 Memory Controller supports dynamic throttling of memory which can
be used to save power when system is idle. This driver does the memory
throttling when all CPUs are idle on such a system.

Refer to "Intel 7300 Memory Controller Hub (MCH)" datasheet
for the config space description.

Signed-off-by: Andy Henroid <andrew.d.henroid@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
2008-10-21 23:58:41 -04:00
Linus Torvalds b91385236c Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
  fsldma: allow Freescale Elo DMA driver to be compiled as a module
  fsldma: remove internal self-test from Freescale Elo DMA driver
  drivers/dma/dmatest.c: switch a GFP_ATOMIC to GFP_KERNEL
  dmatest: properly handle duplicate DMA channels
  drivers/dma/ioat_dma.c: drop code after return
  async_tx: make async_tx_run_dependencies() easier to read
2008-10-20 12:54:30 -07:00
Haavard Skinnemoen 7fe7b2f4ec dw_dmac: fix copy/paste bug in tasklet
The tasklet checks RAW.BLOCK twice, and does not check RAW.XFER. This is
obviously wrong, and could theoretically cause the driver to hang.

Reported-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-03 18:22:18 -07:00
Timur Tabi 77cd62e808 fsldma: allow Freescale Elo DMA driver to be compiled as a module
Modify the Freescale Elo / Elo Plus DMA driver so that it can be compiled as
a module.

The primary change is to stop treating the DMA controller as a bus, and the
DMA channels as devices on the bus.  This is because the Open Firmware (OF)
kernel code does not allow busses to be removed, so although we can call
of_platform_bus_probe() to probe the DMA channels, there is no
of_platform_bus_remove().  Instead, the DMA channels are manually probed,
similar to what fsl_elbc_nand.c does.

Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-09-26 17:00:11 -07:00
Timur Tabi 59f647c25a fsldma: remove internal self-test from Freescale Elo DMA driver
The Freescale Elo DMA driver runs an internal self-test before registering
the channels with the DMA engine.  This self-test has a fundemental flaw in
that it calls the DMA engine's callback functions directly before the
registration.  However, the registration initializes some variables that the
callback functions uses, namely the device struct.

The code works today because there are two device structs: the one created
by the DMA engine, and one created by the Open Firmware (OF) subsystem.  The
self-test currently uses the device struct created by OF.  However, in the
future, some of the device structs created by OF will be eliminated.
This means that the self-test will only have access to the device struct
created by the DMA engine.  But this device struct isn't initialized when
the self-test runs, and this causes a kernel panic.

Since there is already a DMA test module (dmatest), the internal self-test
code is not useful anyway.  It is extremely unlikely that the test will fail
in normal usage.  It may have been helpful during development, but not any more.

Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-09-23 15:55:56 -07:00
Andrew Morton 6fdb8bd471 drivers/dma/dmatest.c: switch a GFP_ATOMIC to GFP_KERNEL
It was needlessly using the unreliable GFP_ATOMIC.

Cc: Timur Tabi <timur@freescale.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-09-19 04:16:23 -07:00
Timur Tabi 6b3141962d dmatest: properly handle duplicate DMA channels
Update the the dmatest driver so that it handles duplicate DMA channels
properly.

When a DMA client is notified of an available DMA channel, it must check if it
has already allocated resources for that channel.  If so, it should return
DMA_DUP.  This can happen, for example, if a DMA driver calls
dma_async_device_register() more than once.

Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-09-19 04:16:19 -07:00
Julia Lawall 89f72a0633 drivers/dma/ioat_dma.c: drop code after return
The break after the return serves no purpose.

Signed-off-by: Julia Lawall <julia@diku.dk>
Reviewed-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-09-13 20:05:34 -07:00
Russell King 492c71dd54 Merge branch 'for-rmk' of git://git.marvell.com/orion 2008-08-09 18:03:13 +01:00
Lennert Buytenhek 6f088f1d21 [ARM] Move include/asm-arm/plat-orion to arch/arm/plat-orion/include/plat
This patch performs the equivalent include directory shuffle for
plat-orion, and fixes up all users.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
2008-08-09 13:44:58 +02:00
Linus Torvalds 49b75b87ce Merge branch 'for-linus-merged' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus-merged' of master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 5177/1: arm/mach-sa1100/Makefile: remove CONFIG_SA1100_USB
  [ARM] 5166/1: magician: add MAINTAINERS entry
  [ARM] fix pnx4008 build errors
  [ARM] Fix SMP booting with non-zero PHYS_OFFSET
  [ARM] 5185/1: Fix spi num_chipselect for lubbock
  [ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach
  [ARM] Add support for arch/arm/mach-*/include and arch/arm/plat-*/include
  [ARM] Remove asm/hardware.h, use asm/arch/hardware.h instead
  [ARM] Eliminate useless includes of asm/mach-types.h
  [ARM] Fix circular include dependency with IRQ headers
  avr32: Use <mach/foo.h> instead of <asm/arch/foo.h>
  avr32: Introduce arch/avr32/mach-*/include/mach
  avr32: Move include/asm-avr32 to arch/avr32/include/asm
  [ARM] sa1100_wdt: use reset_status to remember watchdog reset status
  [ARM] pxa: introduce reset_status and clear_reset_status for driver's usage
  [ARM] pxa: introduce reset.h for reset specific header information
2008-08-08 11:38:42 -07:00
Luis R. Rodriguez 7d283aee50 list.h: Add list_splice_tail() and list_splice_tail_init()
If you are using linked lists for queues list_splice() will not do what
you would expect even if you use the elements passed reversed. We need
to handle these differently. We add list_splice_tail() and
list_splice_tail_init().

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-07 09:49:42 -04:00
Russell King a09e64fbc0 [ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach
This just leaves include/asm-arm/plat-* to deal with.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-08-07 09:55:48 +01:00
Maciej Sosnowski 7f1b358a23 I/OAT: I/OAT version 3.0 support
This patch adds to ioatdma and dca modules
support for Intel I/OAT DMA engine ver.3 (aka CB3 device).
The main features of I/OAT ver.3 are:
 * 8 single channel DMA devices (8 channels total)
 * 8 DCA providers, each can accept 2 requesters
 * 8-bit TAG values and 32-bit extended APIC IDs

Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-22 17:30:57 -07:00
Maciej Sosnowski 16a37acaaf I/OAT: tcp_dma_copybreak default value dependent on I/OAT version
I/OAT DMA performance tuning showed different optimal values of
tcp_dma_copybreak for different I/OAT versions (4096 for 1.2 and 2048
for 2.0).  This patch lets ioatdma driver set tcp_dma_copybreak value
according to these results.

[dan.j.williams@intel.com: remove some ifdefs]
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-22 17:30:57 -07:00
Maciej Sosnowski 09177e85d6 I/OAT: Add watchdog/reset functionality to ioatdma
Due to occasional DMA channel hangs observed for I/OAT versions 1.2 and 2.0
a watchdog has been introduced to check every 2 seconds
if all channels progress normally.
If stuck channel is detected, driver resets it.
The reset is done in two parts. The second part is scheduled
by the first one to reinitialize the channel after the restart.

Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-22 10:07:33 -07:00
Dan Williams 5eb907aaaf iop_adma: document how to calculate the minimum descriptor pool size
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-17 17:59:56 -07:00
Dan Williams c7141d005a iop_adma: directly reclaim descriptors on allocation failure
Force callers that trigger an "out of descriptors" condition to run the
cleanup loop directly.  Alleviates the requirement to have soft-irqs
enabled when polling for a descriptor in async_xor.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-17 17:59:56 -07:00
Haavard Skinnemoen 3bfb1d20b5 dmaengine: Driver for the Synopsys DesignWare DMA controller
This adds a driver for the Synopsys DesignWare DMA controller (aka
DMACA on AVR32 systems.) This DMA controller can be found integrated
on the AT32AP7000 chip and is primarily meant for peripheral DMA
transfer, but can also be used for memory-to-memory transfers.

This patch is based on a driver from David Brownell which was based on
an older version of the DMA Engine framework. It also implements the
proposed extensions to the DMA Engine API for slave DMA operations.

The dmatest client shows no problems, but there may still be room for
improvement performance-wise. DMA slave transfer performance is
definitely "good enough"; reading 100 MiB from an SD card running at ~20
MHz yields ~7.2 MiB/s average transfer rate.

Full documentation for this controller can be found in the Synopsys
DW AHB DMAC Databook:

http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf

The controller has lots of implementation options, so it's usually a
good idea to check the data sheet of the chip it's intergrated on as
well. The AT32AP7000 data sheet can be found here:

http://www.atmel.com/dyn/products/datasheets.asp?family_id=682


Changes since v4:
  * Use client_count instead of dma_chan_is_in_use()
  * Add missing include
  * Unmap buffers unless client told us not to

Changes since v3:
  * Update to latest DMA engine and DMA slave APIs
  * Embed the hw descriptor into the sw descriptor
  * Clean up and update MODULE_DESCRIPTION, copyright date, etc.

Changes since v2:
  * Dequeue all pending transfers in terminate_all()
  * Rename dw_dmac.h -> dw_dmac_regs.h
  * Define and use controller-specific dma_slave data
  * Fix up a few outdated comments
  * Define hardware registers as structs (doesn't generate better
    code, unfortunately, but it looks nicer.)
  * Get number of channels from platform_data instead of hardcoding it
    based on CONFIG_WHATEVER_CPU.
  * Give slave clients exclusive access to the channel

Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>,
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:59:42 -07:00
Haavard Skinnemoen dc0ee6435c dmaengine: Add slave DMA interface
This patch adds the necessary interfaces to the DMA Engine framework
to use functionality found on most embedded DMA controllers: DMA from
and to I/O registers with hardware handshaking.

In this context, hardware hanshaking means that the peripheral that
owns the I/O registers in question is able to tell the DMA controller
when more data is available for reading, or when there is room for
more data to be written. This usually happens internally on the chip,
but these signals may also be exported outside the chip for things
like IDE DMA, etc.

A new struct dma_slave is introduced. This contains information that
the DMA engine driver needs to set up slave transfers to and from a
slave device. Most engines supporting DMA slave transfers will want to
extend this structure with controller-specific parameters.  This
additional information is usually passed from the platform/board code
through the client driver.

A "slave" pointer is added to the dma_client struct. This must point
to a valid dma_slave structure iff the DMA_SLAVE capability is
requested.  The DMA engine driver may use this information in its
device_alloc_chan_resources hook to configure the DMA controller for
slave transfers from and to the given slave device.

A new operation for preparing slave DMA transfers is added to struct
dma_device. This takes a scatterlist and returns a single descriptor
representing the whole transfer.

Another new operation for terminating all pending transfers is added as
well. The latter is needed because there may be errors outside the scope
of the DMA Engine framework that may require DMA operations to be
terminated prematurely.

DMA Engine drivers may extend the dma_device, dma_chan and/or
dma_slave_descriptor structures to allow controller-specific
operations. The client driver can detect such extensions by looking at
the DMA Engine's struct device, or it can request a specific DMA
Engine device by setting the dma_dev field in struct dma_slave.

dmaslave interface changes since v4:
  * Fix checkpatch errors
  * Fix changelog (there are no slave descriptors anymore)

dmaslave interface changes since v3:
  * Use dma_data_direction instead of a new enum
  * Submit slave transfers as scatterlists
  * Remove the DMA slave descriptor struct

dmaslave interface changes since v2:
  * Add a dma_dev field to struct dma_slave. If set, the client can
    only be bound to the DMA controller that corresponds to this
    device.  This allows controller-specific extensions of the
    dma_slave structure; if the device matches, the controller may
    safely assume its extensions are present.
  * Move reg_width into struct dma_slave as there are currently no
    users that need to be able to set the width on a per-transfer
    basis.

dmaslave interface changes since v1:
  * Drop the set_direction and set_width descriptor hooks. Pass the
    direction and width to the prep function instead.
  * Declare a dma_slave struct with fixed information about a slave,
    i.e. register addresses, handshake interfaces and such.
  * Add pointer to a dma_slave struct to dma_client. Can be NULL if
    the DMA_SLAVE capability isn't requested.
  * Drop the set_slave device hook since the alloc_chan_resources hook
    now has enough information to set up the channel for slave
    transfers.

Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:59:35 -07:00
Dan Williams e1d181efb1 dmaengine: add DMA_COMPL_SKIP_{SRC,DEST}_UNMAP flags to control dma unmap
In some cases client code may need the dma-driver to skip the unmap of source
and/or destination buffers.  Setting these flags indicates to the driver to
skip the unmap step.  In this regard async_xor is currently broken in that it
allows the destination buffer to be unmapped while an operation is still in
progress, i.e. when the number of sources exceeds the hardware channel's
maximum (fixed in a subsequent patch).

Acked-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:59:12 -07:00
Haavard Skinnemoen 848c536a37 dmaengine: Add dma_client parameter to device_alloc_chan_resources
A DMA controller capable of doing slave transfers may need to know a
few things about the slave when preparing the channel. We don't want
to add this information to struct dma_channel since the channel hasn't
yet been bound to a client at this point.

Instead, pass a reference to the client requesting the channel to the
driver's device_alloc_chan_resources hook so that it can pick the
necessary information from the dma_client struct by itself.

[dan.j.williams@intel.com: fixed up fsldma and mv_xor]
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:58:58 -07:00
Haavard Skinnemoen 4a776f0aa9 dmatest: Simple DMA memcpy test client
This client tests DMA memcpy using various lengths and various offsets
into the source and destination buffers. It will initialize both
buffers with a repeatable pattern and verify that the DMA engine copies
the requested region and nothing more. It will also verify that the
bytes aren't swapped around, and that the source buffer isn't modified.

The dmatest module can be configured to test a specific device, a
specific channel. It can also test multiple channels at the same time,
and it can start multiple threads competing for the same channel.

Changes since v2:
  * Support testing multiple channels at the same time
  * Support testing with multiple threads competing for the same channel
  * Use counting test patterns in order to catch byte ordering issues

Changes since v1:
  * Remove extra dashes around "help"
  * Remove "default n" from Kconfig
  * Turn TEST_BUF_SIZE into a module parameter
  * Return DMA_NAK instead of DMA_DUP
  * Print unhandled events
  * Support testing specific channels and devices
  * Move to the end of the Makefile

Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:58:45 -07:00
Saeed Bishara ff7b04796d dmaengine: DMA engine driver for Marvell XOR engine
The XOR engine found in Marvell's SoCs and system controllers
provides XOR and DMA operation, iSCSI CRC32C calculation, memory
initialization, and memory ECC error cleanup operation support.

This driver implements the DMA engine API and supports the following
capabilities:
- memcpy
- xor
- memset

The XOR engine can be used by DMA engine clients implemented in the
kernel, one of those clients is the RAID module.  In that case, I
observed 20% improvement in the raid5 write throughput, and 40%
decrease in the CPU utilization when doing array construction, those
results obtained on an 5182 running at 500Mhz.

When enabling the NET DMA client, the performance decreased, so
meanwhile it is recommended to keep this client off.

Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:58:36 -07:00
Kay Sievers ebabe27626 iop-adma: fix platform driver hotplug/coldplug
Since 43cc71eed1, the platform
modalias is prefixed with "platform:". Add MODULE_ALIAS() to most
of the hotpluggable platform drivers, to re-enable auto loading.

Cc: <stable@kernel.org>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:58:28 -07:00
Dan Williams 7cc5bf9a3a dmaengine: track the number of clients using a channel
Haavard's dma-slave interface would like to test for exclusive access to a
channel.  The standard channel refcounting is not sufficient in that it
tracks more than just client references, it is also inaccurate as reference
counts are percpu until the channel is removed.

This change also enables a future fix to deallocate resources when a client
declines to use a capable channel.

Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:58:21 -07:00
Dan Williams 9c402f4e19 dmaengine: remove arch dependency from DMADEVICES
The dependency is redundant since all drivers set their specific arch
dependencies.  The NET_DMA option is modified to be enabled only on platforms
where it is known to have a positive effect.  HAS_DMA is added as an explicit
dependency for the DMADEVICES menu.

Acked-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:58:12 -07:00
Haavard Skinnemoen 1099dc7924 dmaengine: Couple DMA channels to their physical DMA device
Set the 'parent' field of channel class devices to point to the
physical DMA device initialized by the DMA engine driver.

This allows drivers to use chan->dev.parent for syncing DMA buffers
and adds a 'device' symlink to the real device in
/sys/class/dma/dmaXchanY.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:58:05 -07:00
Li Yang 51ee87f27a fsldma: fix incorrect exit path for initialization
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Zhang Wei <zw@zh-kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:57:45 -07:00
Christophe Jaillet eccf2144e1 iop-adma: fixup some kzalloc/memset confusions
1) Remove an explicit memset(.., 0, ...) to a variable allocated with
kzalloc (i.e. 'dest').

2) Allocate 'src' with kmalloc instead of kzalloc as all elements of the
'src' buffer are initialized in a 'for(...)' loop just after.

3) remove useless 'sizeof(u8)', which always returns 1, when computing the
size of the memory to be allocated.

Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-05-20 13:51:20 -07:00
Sebastian Siewior 8a5703f846 DMA engine: typo fixes
Spelling fixes for dmaengine.[ch]

Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
2008-04-21 22:38:45 +00:00
Dan Williams 636bdeaa12 dmaengine: ack to flags: make use of the unused bits in the 'ack' field
'ack' is currently a simple integer that flags whether or not a client is done
touching fields in the given descriptor.  It is effectively just a single bit
of information.  Converting this to a flags parameter allows the other bits to
be put to use to control completion actions, like dma-unmap, and capture
results, like xor-zero-sum == 0.

Changes are one of:
1/ convert all open-coded ->ack manipulations to use async_tx_ack
   and async_tx_test_ack.
2/ set the ack bit at prep time where possible
3/ make drivers store the flags at prep time
4/ add flags to the device_prep_dma_interrupt prototype

Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17 13:25:54 -07:00
Dan Williams c4fe15541d iop-adma: remove the workaround for missed interrupts on iop3xx
This workaround was covering the dependency submission bug in async_tx.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17 13:25:54 -07:00
Dan Williams ce4d65a5db async_tx: kill ->device_dependency_added
DMA drivers no longer need to be notified of dependency submission
events as async_tx_run_dependencies and async_tx_channel_switch will
handle the scheduling and execution of dependent operations.

[sfr@canb.auug.org.au: extend this for fsldma]
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17 13:25:54 -07:00
Dan Williams 19242d7233 async_tx: fix multiple dependency submission
Shrink struct dma_async_tx_descriptor and introduce
async_tx_channel_switch to properly inject a channel switch interrupt in
the descriptor stream.  This simplifies the locking model as drivers no
longer need to handle dma_async_tx_descriptor.lock.

Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17 13:25:05 -07:00
Zhang Wei 1c62979ed2 fsldma: Split the MPC83xx event from MPC85xx and refine irq codes.
Split MPC83xx EOCDI event from MPC85xx EOLNI event, which is
also need to update cookie and start the next transfer.
The DMA channel irq handler function code is refined.
The patch is tested on MPC8377MDS board.

Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by; Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17 13:22:16 -07:00
Zhang Wei 411e23dbe9 fsldma: Remove CONFIG_FSL_DMA_SELFTEST, keep fsl_dma_self_test() running always.
Always enabling the fsl_dma_self_test() to ensure the DMA controller
should works well after the driver probed.

Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17 13:22:15 -07:00