Access to the interrupt page registers has been broken since at least
commit 3999e5d01d ("[media] adv7180: Do implicit register paging").
That commit forgot to add the interrupt page number to the register
defines.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The adv7511 will automatically fill in the VIC code in the AVI InfoFrame
based on the timings of the incoming pixelport signals.
However, to have this work correctly it needs to specify the fps
value in a register. After doing this the proper VIC code is filled in.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Correctly set the h/vsync polarities instead of keeping to the
default (positive).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix a number of bugs that appeared when support for mediabus formats was
added:
- Support for V4L2_DV_RGB_RANGE_FULL/LIMITED should only be enabled
for HDMI RGB formats, not for YCbCr formats. Since, as the name
says, this setting is for RGB only. So read the InfoFrame to check
the format.
- the quantization range for the pixelport depends on whether the
mediabus code is RGB or not: if it is RGB, then produce full range
RGB values, otherwise produce limited range YCbCr values.
This means that the op_656_range and alt_data_sat fields of the
platform data are no longer used and these will be removed in a
following patch.
- when setting up a new format the RGB quantization range settings
were never updated. Do so, since this depends on the format.
- fix the log_status output which was confusing and incorrect.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit 1fb69bfd29 (adv7511: improve
colorspace handling) introduced a number of bugs, specifically with
regards to YCbCr output and quantization range handling:
- if the output is not RGB, then disable the full-to-limited range
CSC matrix since that is meant for RGB formats. YCbCr formats are
always limited range, so there is nothing to convert. (OK, full
range YCbCr is possible, but we don't support that right now).
- the mediabus code that was passed to adv7511_set_fmt was always cleared
by the memset in adv7511_fill_format. This made it effectively impossible
to select YCbCr output.
- adv7511_set_fmt never updated the rgb quantization range.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The IT Content bit has nothing to do with CE vs IT timings.
Delete this code. This will also fix a bug where this could
override the 'content type' control, which is actually the
correct place to set/clear the ITC bit.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Nobody is using these ops anymore, so remove these callbacks from
the subdev drivers that still have them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The part can be reset by a low pulse on the RESET pin (i.e. a hardware
reset) with a minimum width of 5 ms. It is recommended to wait 5 ms
after the low pulse before an I2C write is performed to the part.
For safety reasons, the delays will be between 5 and 10 ms.
The RESET pin can be tied high, so the GPIO is optional.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_queues" enables hotplugging.
It has a single work item(&state->delayed_work_enable_hotplug) and hence
doesn't require ordering. Also, it is not being used on a memory
reclaim path. Hence, the singlethreaded workqueue has been replaced with
the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been sync cancelled in adv76xx_remove() to ensure
that there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_queues" enables hotplugging.
It has a single work item(&state->delayed_work_enable_hotplug) and hence
doesn't require ordering. Also, it is not being used on a memory
reclaim path. Hence, the singlethreaded workqueue has been replaced with
the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been sync cancelled in tc358743_remove() to ensure
that there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_queues" enables hotplugging.
It has a single work item(&state->delayed_work_enable_hotplug) and hence
doesn't require ordering. Also, it is not being used on a memory
reclaim path. Hence, the singlethreaded workqueue has been replaced with
the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been sync cancelled in adv7842_remove() to ensure
that there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add CEC support to the adv7511 driver.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
[k.debski@samsung.com: Merged changes from CEC Updates commit by Hans Verkuil]
Signed-off-by: Kamil Debski <kamil@wypas.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add CEC support to the adv7842 driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add CEC support to the adv7604 driver.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
[k.debski@samsung.com: Merged changes from CEC Updates commit by Hans Verkuil]
[k.debski@samsung.com: add missing methods cec/io_write_and_or]
[k.debski@samsung.com: change adv7604 to adv76xx in added functions]
[hansverk@cisco.com: use _clr_set instead of _and_or]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dv_timings_cap() and enum_dv_timings() pad operations take a pad
number as an input argument and return the DV timings capabilities and
list of supported DV timings for that pad.
Commit bd3e275f3e ("[media] media: i2c: adv7604: Use v4l2-dv-timings
helpers") broke this as it started ignoring the pad number, always
returning the information associated with the currently selected input.
Fix it.
Fixes: bd3e275f3e ("[media] media: i2c: adv7604: Use v4l2-dv-timings helpers")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds V4L2 controls for Auto Exposure Control and Auto Gain
Control settings. These settings include low pass filter, update
frequency of these settings and the update interval for those units.
[Avoid forward declarations]
[Fix 80 columns limit violation]
[Rename controls to avoid underscores in names]
[Fix the AEC maximum shutter width on MT9V032]
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The power_on function of the driver resets the chip and sets the
CHIP_CONTROL register to 0. This switches the operating mode to slave.
The s_stream function sets the correct mode. But this caused problems on
a board where the camera chip is operated as master. The camera started
after a random amount of time streaming an image, I observed between 10
and 300 seconds.
The STRFM_OUT and STLN_OUT pins are not connected on this board which
may cause some issues in slave mode. I could not find any documentation
about this.
Keeping the chip in master mode after the reset helped to fix this
issue for me.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit b42261078a ("regmap: i2c: fallback to SMBus if the adapter
does not support standard I2C"), regmap-i2c will check the
I2C_FUNC_SMBUS_[BYTE|WORD]_DATA functionality based on the regmap_config
setting if the adapter does not support standard I2C.
So remove the I2C_FUNC_SMBUS_WORD_DATA functionality check in the driver code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the driver fails to reset the camera or to set up control handlers, it
has to power the camera back off.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This v4l2_subdev_internal_ops structure is never modified. All other
v4l2_subdev_internal_ops structures are declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The value is not used after the assignment.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Gcc 6.1 warns about an unused table:
drivers/media/i2c/adv7842.c:2400:27: warning: 'prim_mode_txt' defined but not used [-Wunused-const-variable=]
static const char * const prim_mode_txt[] = {
^~~~~~~~~~~~~
That seems to be useful for debug, and likely were used before.
While we could simply remove, let's comment it out, for now.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tvp5150_write() function can fail so don't return 0 unconditionally
in tvp5150_s_register() but propagate what's returned by tvp5150_write().
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The tvp5150_write() function calls i2c_smbus_write_byte_data() that
can fail but does not propagate the error to the caller. Instead it
just prints a debug, so callers can't know if the operation failed.
So change the function to return the error code to the caller so it
knows that the write failed and also print an error instead of just
printing a debug information.
While being there remove the inline keyword from tvp5150_write() to
make it consistent with tvp5150_read() and also because it's called
in a lot of places, so making inline is in fact counter productive
since it makes the kernel image size to be much bigger (~16 KiB).
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The extraneous assignment on bt is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It's been reported that CJC7113 devices are returning
all 1s when reading register 0:
"1111111111111111" found @ 0x4a (stk1160)
This new device is apparently compatible with SA7113, so let's
add a quirk to allow its autodetection. Given there isn't
any known differences with SAA7113, this commit does not
introduces a new saa711x_model value.
Reported-by: Philippe Desrochers <desrochers.philippe@gmail.com>
Signed-off-by: Kevin Fitch <kfitch42@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some sensors (like the one in Nokia N900) provide metadata in the first
couple of lines. Make that information information available to the
pipeline.
Use u16 instead, this is a 16-bit value.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The devm_gpiod_get() function returns either a valid pointer to
struct gpio_desc or ERR_PTR() error value, check for NULL is bogus.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add entries for all supported chip variants into the of_match list, so that
the matching driver_info can be selected when using dt.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Marking these controls as private seemed a good idea at one time,
but in practice it makes no sense. So drop this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The control in question is not a private control, so drop that
comment. Copy-and-paste left-over.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The adv7180 attempts to autodetect the standard. Unfortunately this
is seriously broken.
This patch removes the autodetect completely. Only the querystd op
will detect the standard. Since the design of the adv7180 requires
that you switch to a special autodetect mode you cannot call querystd
when you are streaming.
So the s_stream op has been added so we know whether we are streaming
or not, and if we are, then querystd returns EBUSY.
After testing this with a signal generator is became obvious that
a sleep is needed between changing the standard to autodetect and
reading the status. So the autodetect can never have worked well.
The s_std call now just sets the new standard without any querying.
If the driver supports the interrupt, then when it detects a standard
change it will signal that by sending the V4L2_EVENT_SOURCE_CHANGE
event.
With these changes this driver now behaves like all other video
receivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The ADV7180 supports NTSC, PAL and SECAM.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support to get the pixel aspect ratio depending on the current
standard (50 vs 60 Hz).
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support to get the standard to the adv7180 driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Smatch complains that there are some paths where "status" isn't
initialized. The code does assume that m5mols_read_u8() can fail so it
seems as if Smatch is correct.
Let's initialize it to REG_ISO_AUTO which is zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need to import the changes at media.h, as we have a
followup patch that depends on it.
* v4l_for_linus:
[media] media.h: use hex values for range offsets, move connectors base up.
[media] adv7604: fix tx 5v detect regression
smatch complains about non-ascii characters. It turns out that a wide-dash character
was used instead of the more common '-' character.
Replace those dashes with -.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The V4L2_CID_TX_EDID_PRESENT control reports if an EDID is present.
The adv7511 however still reported the EDID present after disconnecting
the HDMI cable. Fix the logic regarding this control. And when the EDID
is disconnected also call ADV7511_EDID_DETECT to notify the bridge driver.
This was also missing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v3.12 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The 5 volt detect functionality broke in 3.14: the code reads IO register 0x70
again after it has already been cleared. Instead it should use the cached
irq_reg_0x70 value and the io_write to 0x71 to clear 0x70 can be dropped since
this has already been done.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v3.14 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some macros were changed/removed at the material for v4.5. We need
to sync with those changes here, in order to avoid troubles.
* v4l_for_linus:
[media] media.h: get rid of MEDIA_ENT_F_CONN_TEST
[media] [for,v4.5] media.h: increase the spacing between function ranges
[media] media: i2c/adp1653: probe: fix erroneous return value
[media] media: davinci_vpfe: fix missing unlock on error in vpfe_prepare_pipeline()
MEDIA_ENT_F_CONN_TEST is not really a connector, it is actually
a signal generator. Also, as other drivers use the
V4L2_CID_TEST_PATTERN control for signal generators, let's change
the driver accordingly.
Tested with Terratec Grabster AV350.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The tvp5150 decoder has different input connectors. The actual list of
HW inputs depends on the device version but all have at least these 3:
1) Composite0
2) Composite1
3) S-Video
and some variants have a 4th possible input connector:
4) Signal generator
The driver currently uses the .s_routing callback to switch the input
connector but since these are separate HW blocks, it's better to use
media entities to represent the input connectors and their source pads
linked with the decoder's sink pad.
This allows user-space to use the MEDIA_IOC_SETUP_LINK ioctl to choose
the input connector. For example using the media-ctl user-space tool:
$ media-ctl -r -l '"Composite0":0->"tvp5150 1-005c":0[1]'
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a header file for the tvp5150 input connectors constants that
can be shared between the driver and Device Tree source files.
[mchehab@osg.samsung.com: rename tvp5150.h also at em28xx-cards.c]
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
