Update a couple of S3C24XX and S3C2412 files that are still
using the GPIO number to register mapping calls to get the
s3c_gpio_chip and use the base field from that.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Start cleaning up the numbering of GPIO banks by removing the old
bank start definitions currently being used by some of the header
files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The address ben@fluff.org is old, ben-linux@fluff.org has been in use
for a long time, and we should fixup all the occasions of the older
address to avoid confusion.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add arch/arm/mach-s3c2416 for support of the Samsung S3C2416 SoC.
This patch adds support of the S3C2416 SoC, clocks, timers,
and initial IRQ support (without support of secondary set of registers).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
[ben-linux@fluff.org: removed files to be reworked, fixed conflicts]
[ben-linux@fluff.org: use s3c2443 reset instead of specific reset code]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The S3C DMA API doesn't make use of hw_addr.to/from and also
the FIFO addresses are provided from the I2S drivers. So these
fields are redundant.
This patch removes the hw_addr.to/from fields for I2S and the
inclusion of header, paving way for the header to be moved closer
to the I2S controller drivers.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The s3c_gpio_cfgpin() call should be functionally equivalent, so replace
the s3c2410_gpio_cfgpin() calls in the s3c24xx code with s3c_gpio_cfgpin
to allow moving away from a fixed GPIO number to register address mapping
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change mach-jive to use gpiolib for the GPIO lines that are directly
manipulated by it.
Note, we ignore any errors from gpio_request(), unlikely to see any.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
dma-plat.h is the last file left in plat-s3c64xx, but to remove it we
must also change the use of dma-plat.h by the core code and the s3c24xx
implementation.
Rename the s3c24xx dma-plat.h in the common plat-samsung directory as it
may be used for other ports. Move the specific dma bits into the
mach-s3c64xx directory and update the build as needed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Prepare for the forthcoming device changes by renaming s3c_device_usb to
s3c_device_ohci as this is what the device represents.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Reduce the size of struct clk by 12 bytes and make defining clocks with
common implementation functions easier by moving the set_rate, get_rate,
round_rate and set_parent calls into a new structure called 'struct clk_ops'
and using that instead.
This change does make a few clocks larger as they need their own clk_ops,
but this is outweighed by the number of clocks with either no ops or having
a common set of ops.
Update all the users of this.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
A number of machines that need s3c_device_nand present do not select
this in their Kconfig entries. Add the necessary selection of the
configuration S3C_DEV_NAND so that we avoid the following error:
arch/arm/mach-s3c2410/built-in.o: In function `bast_map_io':
arch/arm/mach-s3c2410/mach-bast.c:634: undefined reference to `s3c_device_nand'
arch/arm/mach-s3c2412/built-in.o: In function `s3c2412_init_uarts':
arch/arm/mach-s3c2412/s3c2412.c:109: undefined reference to `s3c_device_nand'
arch/arm/mach-s3c2412/built-in.o: In function `jive_machine_init':
arch/arm/mach-s3c2412/mach-jive.c:673: undefined reference to `s3c_device_nand'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add debugfs support for the cpufreq driver to allow
information about the system state to be exported to
the user.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Update the mapping of the memory controler registers and
add the missing definitions of the register block for the
SSMC.
The register contents definitions can be found in the pl093
header.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Prepare to remove the large number of S3C2410_GPxn defines
by moving to S3C2410_GPx(n) in arch/arm.
The following perl was used to change the files:
perl -pi~ -e 's/S3C2410_GP([A-Z])([0-9]+)([^_^0-9])/S3C2410_GP\1\(\2\)\3/g'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move all the gpio functions out of <mach/hardware.h> as
this file is for defining the generic IO base addresses
for the kernel IO calls.
Make a new header <mach/gpio-fns.h> to take this and
include it via the chain from <linux/gpio.h> which is
what most of these files should be using (and will be
changed as soon as possible).
Note, this does make minor changes to some drivers but
should not mess up any pending merges.
CC: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add common definition for USB OHCI platform device, add a Kconfig
to selectively compile it and add update all the users.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The alterations to the suspend code missed adding a
call to the cache flushing routines during the suspend
path of the S3C2412.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The <mach/dma.h> is for the driver API for the DMA system and should
not have anything relying on the CPU specific registers.
Remove the registers to <plat/dma-regs.h> for the code that really
needs to know about them.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the platform dma.h to dma-plat.h to ensure it doen't get
confused with plat/dma.h
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make 'jive_vgg2432a4_display' and 'jive_lcd_config' static as
they are not exported, and are generating the following sparse
warnings:
mach-jive.c:280:26: warning: symbol 'jive_vgg2432a4_display' was not declared. Should it be static?
mach-jive.c:313:28: warning: symbol 'jive_lcd_config' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The platform data for the i2c-s3c2410 driver used to allow a min,
max and desired frequency for the I2C bus. This patch reduces it
to simply a desired frequency ceiling and corrects all the uses
of the platform data appropriately.
This means, for example, that on a system with a 66MHz fclk, a
request for 100KHz will achieve 65KHz which is safe and
acceptable, rather than 378KHz which it would have achieved
without this change.
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
[ben-linux@fluff.org: tidy subject and description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Rename s3c2410_cpu_resume to s3c_cpu_resume and s3c2410_cpu_save to
s3c_cpu_save to remove the CPU specific naming of these functions
which are now in the generic PM code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since we have moved a large proportion of the PM code to the common
support area, remove the cpu specific name from the initialisation
function.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Start moving the PM code by moving all the common support functions
to a common location in arch/arm/plat-s3c. With the move we rename
the functions from s3cxxx_ to s3c_ to fit the new location.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the IIS headers to their correct place.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As per Russell King's last review comment, find and remove
all unnecessary includes of <linux/delay.h> in the files
that do not need them.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the name of the driver, as well as the fact we are not
passing the number of chipselects to the driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The S3C64XX timer is running at the wrong rate due to the
assumptions made in the timer initialisation about the way
the pwm dividers work. This means that time on the S3C64XX
runs twice as fast as it should.
Fix the problem by moving to using the clk framework to setup
the pwm timer clock muxes, as the pwm-clock code has all the
necessary knowledge of how the timer clock inputs are routed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the initial clocks definitions for the s3c6400
and s3c6410. Move the epll and ext clock from the
s3c2443 support into the common code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Update the clock settings on resume for suspend/resume
support so that if the boot loader changes anything or
the system's PLL is reset then we return with the correct
settings.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the PLL calculation code into it's own header
file for re-use with the other plat-s3c24xx based
systems such as the S3C24A0.
Note, we change the name of s3c2410_get_pll to the
more generically named s3c24xx_get_pll as well as
the related defintions.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We need to add plat-s3c to the build to get the headers
that will go in here once moved from include/asm-arm so
we may as well put some useful common s3c code in here
to stop the errors generated form having nothing built.
The cpu setup is now passed the cpu idcode and the table
of supported cpus to s3c_init_cpu() to abstract the
cpu identification out of the initial io setup.
As well as moving the cpu initialisation code, we move the
map of the board specific items up to the calling code as
none of the map_io() functions actually do anything other
than pass this to iotable_init().
This patch does not rename any of the init functions that
will be common to s3c24xx and any other s3c architectures
as this can be done at a later date as it will touch all
the board support files which use functions such as
s3c24xx_init_clocks() and s3c24xx_init_uarts().
Note, the header arch/arm/plat-s3c24xx/include/plat/cpu.h
still has functions that are used by both the cpu and
board initialisation functions. This means that each board
has definitions specific to the cpu support included and
the vice-versa.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When ISA_DMA_API is unset, we're not implementing the ISA DMA API,
so there's no point in publishing the prototypes via asm/dma.h, nor
including the machine dependent parts of that API.
This allows us to remove a lot of mach/dma.h files which don't contain
any useful code. Unfortunately though, some platforms put their own
private non-ISA definitions into mach/dma.h, so we leave these behind
and fix the appropriate #include statments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than:
config CPU_BLAH
bool
depends on ARCH_FOO || MACH_BAR
default y if ARCH_FOO || MACH_BAR
arrange for ARCH_FOO and MACH_BAR to select CPU_BLAH directly.
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: Brian Swetland <swetland@google.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move plat/regs-spi.h to arch/arm/plat-s3c/include/plat ready
ready to clean out old include directories.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the udc headers to the proper home in
arch/arm/plat-s3c24xx/include/plat ready to clean out
the old include directories.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
desc_handle_irq() was declared as obsolete since long ago.
Replace it with generic_handle_irq()
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
First move of items out of include/asm-arm/plat-s3c* to their
new homes under arch/arm/plat-s3c/include/plat and
arch/arm/plat-s3c24xx/include/plat directories.
Note, we have to create a dummy arch/arm/plat-s3c/Makefile to
allow us to add arch/arm/plat-s3c/include/plat to the path.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The first spi bus is registered with number 0, but
the board data says that the device on it is registered
on bus 1.
Move the spi bus to bus 1 to keep the compatibility with the
original board-support patches.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Removed duplicated include file <linux/mtd/mtd.h> and <linux/mtd/partitions.h>
in arch/arm/mach-s3c2412/mach-jive.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For s3c2412, set parent for clk_erefclk and clk_urefclk.
This allow for example to use xtal or extclk for i2s clock.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com>
Add the definitions for the VGG2432A4 intelligent
LCD display conneected via an GPIO-based SPI bus
on the Logitech Jive.
Signed-of-by: Ben Dooks <ben-linux@fluff.org>
Ensure that the S3C2412 sleep configuration registers
are approriately setup so that the device can safely
go to sleep.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the name of the S3C2412_CLKDIVN_ARMDIVN define.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the S3C2412 fclk is derived from msysclk, not straight from
the MPLL output. Set clk_f.parent appropriately.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The msysclk clock was checking for the wrong PLL for the
parent in s3c2412_setparent_msysclk(), trying the UPLL instead
of the MPLL output.
Also ensure the mpll and fclks are at the same rate at init time.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current S3C24XX DMA code does not allow for an peripheral
that has one channel for RX and another for TX.
This patch adds a per-cpu dma operation to select the transmit
or receive channel, and adds support to the S3C2412 for the
seperate DMA channels for TX and RX.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add s3c2412_gpio_set_sleepcfg() to allow the setting of the sleep
configuration of the GPIO blocks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add armclk to the S3C2412 to indicate the current clock connected to
the ARM core.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Check if the sleep command returns due to a pending interrupt
in the standby unit. If this happens, try and ack the IRQ
before re-trying the resume.
It is currently unclear whether the resume can be backed out
of at this stage as this could cause a problem with level
based interrupts.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that if the RTC IRQ is not selected for wake in the
base configuration, then the PWRCFG has the same value set
in it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
S3C2412_GPESLPCON does not exist in the register
mappings, so remove it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IIS and SDI register hw_addr definitions are
incorrect in the DMA map for the S3C2412.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The S3C2412 GPIO is similar enough to the S3C2410 that
it can use it as a base for GPIO functionality.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Fix the IRQ numbers of the CF and SDI interface on the S3C2412
and S3C2413. Add support to handle these IRQs properly and
ensure that the SDI controller platform device is correctly
renumbered.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes section mismatches related to DMA functions.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move register and other definitions out of the
include/asm-arm/arch-s3c2410 into the the arch
directories of include/asm-arm/plat-s3c24xx and
include/asm-arm/plat-s3c.
This move is in preperation of the merging of
s3c2400 and s3c6400.
The following git mv commands are needed before
this patch can be applied:
git mv include/asm-arm/arch-s3c2410/regs-ac97.h include/asm-arm/plat-s3c/regs-ac97.h
git mv include/asm-arm/arch-s3c2410/regs-adc.h include/asm-arm/plat-s3c/regs-adc.h
git mv include/asm-arm/arch-s3c2410/regs-iis.h include/asm-arm/plat-s3c24xx/regs-iis.h
git mv include/asm-arm/arch-s3c2410/regs-spi.h include/asm-arm/plat-s3c24xx/regs-spi.h
git mv include/asm-arm/arch-s3c2410/regs-udc.h include/asm-arm/plat-s3c24xx/regs-udc.h
git mv include/asm-arm/arch-s3c2410/udc.h include/asm-arm/plat-s3c24xx/udc.h
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the static maps for the LCD and USB devices.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the Kconfig to create configuration options based on which
CPUs are supported for the low level serial code. This means that
the debug macros can be optimised for the type(s) of CPU that are
being used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch moves items of the s3c24xx support into
a new plat-s3c directory for items that use the
s3c24xx support but are not directly s3c24xx
compatible, such as the s3c2400 and s3c6400.
git mv commands:
git mv include/asm-arm/arch-s3c2410/iic.h include/asm-arm/plat-s3c/iic.h
git mv include/asm-arm/arch-s3c2410/nand.h include/asm-arm/plat-s3c/nand.h
git mv include/asm-arm/arch-s3c2410/regs-iic.h include/asm-arm/plat-s3c/regs-iic.h
git mv include/asm-arm/arch-s3c2410/regs-nand.h include/asm-arm/plat-s3c/regs-nand.h
git mv include/asm-arm/arch-s3c2410/regs-rtc.h include/asm-arm/plat-s3c/regs-rtc.h
git mv include/asm-arm/arch-s3c2410/regs-serial.h include/asm-arm/plat-s3c/regs-serial.h
git mv include/asm-arm/arch-s3c2410/regs-timer.h include/asm-arm/plat-s3c/regs-timer.h
git mv include/asm-arm/arch-s3c2410/regs-watchdog.h include/asm-arm/plat-s3c/regs-watchdog.h
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The S3C2412 has an reset-errata where the clock
may cause a glitch switching back to EXTCLK. We
force a switch to EXTCLK before writing the
reset register to force use of the CLKCON sync
logic to properly switch.
Fix problem reported by Matthieu Castet.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change the SPI Channel 1 register offset in s3c_spi1_resource[], and
s3c2412_dma_mappings[]. Offset has to be 0x100 in s3c2412/13's case.
Also, total SPI memory resource size changed to 0x24 for s3c2412/13.
Signed-off-by: Sandeep Patil <psandeep.s@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add Kconfig entry for SMDK2412 to go with the SMDK2413
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks