Add support for lookup of sdhci-s3c controller clocks using generic names
for s3c2416, s3c64xx, s5pc100, s5pv210 and exynos4 SoC's.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
[kgene.kim@samsung.com: fixed trailing whitespace]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Samsung uart driver lookups the clock using the connection id 'clk_uart_baud'.
The uart clocks for all Samsung platforms are reorganized to register them
with the lookup name as required by the uart driver.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S3C2443 uses hsmmc1 as its only hsmmc device and for S3C2416/S3C2450
it's the second hsmmc channel with the same PCLKCON bit.
The hsmmc-if clocks on both systems already got a devname, as did
the hsmmc pclk for hsmmc0 on the S3C2416. So to make it possible to
identify the hsmmc1 pclk on S3C2416 add the correct devname for it.
The sclk name on S3C2443 also is s3c-sdhci.1.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Previously the fclk rate was calculated by dividing the pll through
the divider value of the armdiv. With a real armdiv clk in place it's
possible to simply read its value, which does essentially the same.
This change makes the whole fdiv_fn function pointers supplied to
s3c2443_common_init_clocks and s3c2443_common_setup_clocks
obsolete, so remove it too.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cpufreq uses frequencies in kHz and not Hz, so set_rate and round_rate
would be called with a frequency of 266666000 instead of 266666666 but
the clock functions check for rates smaller or equal to the targetrate.
As the armdiv does not support steps this small we can accommodate
this by simply also setting the last 3 digits of the calculated rate
to zero.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The armdiv array may contain unset divider values.
Check the relevant value to prevent division by zero
errors. Also check for set nr_armdiv and armdivmask
before meddling with clkdiv0.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The system-layout of the armdiv and armclk is common to
S3C2443/S3C2416/S3C2450 and only differs in the array of
possible dividers. Therefore it is possible to reuse the
clock definitions for all of these SoCs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is needed for making the armdiv clock common to S3C2443
and S3C2416/2450.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S3C2416/S3C2450 use the same clocks for their i2s blocks
and can therefore reuse the existing ones.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Define maps for HSMMC devices.
S3C2443 has one HSMMC device with base address 0x4A800000.
S3C2416 has HSMMC0 at 0x4AC00000 and HSMMC1 at 0x4A800000.
So suppose that S3C2443 has only HSMMC1.
Define clock for hsmmc0 device and register it.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
To share code with some of the newer parts such as the S3C2416, move
parts of arch/arm/mach-s3c2443/clock.c to a common file called
arch/arm/plat-s3c24xx/s3c2443-clock.c.
Update the build configuration to deal with this new file.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Rajeshwari Shinde
Thomas Abraham
Heiko Stuebner
Thomas Abraham
Yauhen Kharuzhy
Ben Dooks