The semantic patch that makes this change is available
in scripts/coccinelle/api/memdup.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt routine for PCI devices has a special exit that
executes the same instructions as does the normal exit.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver rtlwifi fails on a big-endian host.
These changes have been tested on a Mac PowerBook G4, which has
a PPC processor.
Although this patch touches some of the code that will affect endian
issues on PCI hardware through drivers rtl8192ce, rtl8192se, and
rtl8192de, these have not been tested due to lack of suitable hardware.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver rtl8192cu writes the firmware with 32-bit asynchronous writes. This
design is OK for USB 2.0 adapters, but the current implementation of
xhcu-hcd has a limited ring size, which is exceeded. By converting to
synchronous block writes, this error is avoided.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The USB driver does not retry reads - allow 10 tries.
Signed-off-by: George <george0505@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
User space might want to test if driver supports testmode. Adding testmode
to the list of supported commands makes this easier.
I omitted testmode_dump() in purpose. I assume all drivers implementing
testmode_dump() will also implement testmode_cmd().
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WLAN_STA_ASSOC_AP indicates that the station entry
is for an AP we're associated to but isn't used so
remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers can usually handle fragmented packets
much easier when they get the entire list of
fragments at once. The only thing they need to
do is keep enough space on the queues for up
to ten fragments of a single MSDU.
This allows them to implement this with a new
operation tx_frags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This just prepares for passing the entire fragment
list to the driver. No significant changes, but the
TX throughput is calculated slightly differently
now and we blink only once for each MSDU.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of adjusting the fragment flags at
TX time, adjust them at fragmentation time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are currently linking the skbs by using skb->next
directly. This works, but the preferred way is to use
a struct sk_buff_head instead. That also prepares for
passing that to drivers directly.
While at it I noticed we calculate the duration for
fragments twice -- remove one of them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DFS events are reported as PHY errors and need to be processed
with a correct timestamp set before ath9k_skb_preprocess() is
called and the frame is possibly dropped.
This patch puts the rxs->mactime calculation before the skb
is preprocessed to prepare for DFS event reporting.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This grants drivers access to the DFS region that a
regulatory domain belongs to.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wireless-regdb now has support for mapping a country to
one DFS region. CRDA sends this to us now so process it
so we can provide that hint to drivers. This will later be
used by code for processing DFS in a way that meets the
criteria for the DFS region the country belongs to.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is very similar to bnx2x conversion, but simpler since no special
alignement is required, so goal was not to reduce skb truesize.
Using build_skb() reduces cache line misses in the driver, since we
use cache hot skb instead of cold ones. Number of in-flight sk_buff
structures is lower, they are more likely recycled in SLUB caches
while still hot.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to mask the MMC irq otherwise if we raise the mmc
interrupts that are not handled the driver loops in the
handler.
In fact, by default all mmc counters (only used for stats)
are managed in SW and registers are cleared on each READ.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements advice by Ben Hutchings to change the mii side of
the function names to look more like the register whose values they
convert. New LPA translation functions have been added as well.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The semantic patch that makes this change is available
in scripts/coccinelle/api/memdup.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The semantic patch that makes this change is available
in scripts/coccinelle/api/memdup.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This considers some simple cases that are common and easy to validate
Note in particular that there are no ...s in the rule, so all of the
matched code has to be contiguous
The semantic patch that makes this change is available
in scripts/coccinelle/api/alloc/kzalloc-simple.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The semantic patch that makes this change is available
in scripts/coccinelle/api/alloc/drop_kmalloc_cast.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The semantic patch that makes this change is available
in scripts/coccinelle/api/memdup.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
"remote_list" is of type
struct dma_chunk remote_list[VETH_MAX_FRAMES_PER_MSG];
Probably a copy'n'paste error.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"dwrq->length" is the capped version of "essid->length".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By the time userspace returns with a response to
the regulatory domain request, the wiphy causing
the request might have gone away. If this is so,
reject the update but mark the request as having
been processed anyway.
Cc: Luis R. Rodriguez <lrodriguez@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I intoduced this bug in commit a2fe816674
"mac80211: Build TX radiotap header dynamically"
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was flipped. See section 7.3.2.56 of the 802.11n
spec for details.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The forcedeth changes had a conflict with the conversion over
to atomic u64 statistics in net-next.
The libertas cfg.c code had a conflict with the bss reference
counting fix by John Linville in net-next.
Conflicts:
drivers/net/ethernet/nvidia/forcedeth.c
drivers/net/wireless/libertas/cfg.c
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (86 commits)
ipv4: fix redirect handling
ping: dont increment ICMP_MIB_INERRORS
sky2: fix hang in napi_disable
sky2: enforce minimum ring size
bonding: Don't allow mode change via sysfs with slaves present
f_phonet: fix page offset of first received fragment
stmmac: fix pm functions avoiding sleep on spinlock
stmmac: remove spin_lock in stmmac_ioctl.
stmmac: parameters auto-tuning through HW cap reg
stmmac: fix advertising 1000Base capabilties for non GMII iface
stmmac: use mdelay on timeout of sw reset
sky2: version 1.30
sky2: used fixed RSS key
sky2: reduce default Tx ring size
sky2: rename up/down functions
sky2: pci posting issues
sky2: fix hang on shutdown (and other irq issues)
r6040: fix check against MCRO_HASHEN bit in r6040_multicast_list
MAINTAINERS: change email address for shemminger
pch_gbe: Move #include of module.h
...
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Suspend: Fix bug in suspend statistics update
PM / Hibernate: Fix the early termination of test modes
PM / shmobile: Fix build of sh7372_pm_init() for CONFIG_PM unset
PM Sleep: Do not extend wakeup paths to devices with ignore_children set
PM / driver core: disable device's runtime PM during shutdown
PM / devfreq: correct Kconfig dependency
PM / devfreq: fix use after free in devfreq_remove_device
PM / shmobile: Avoid restoring the INTCS state during initialization
PM / devfreq: Remove compiler error after irq.h update
PM / QoS: Properly use the WARN() macro in dev_pm_qos_add_request()
PM / Clocks: Only disable enabled clocks in pm_clk_suspend()
ARM: mach-shmobile: sh7372 A3SP no_suspend_console fix
PM / shmobile: Don't skip debugging output in pd_power_up()
The check for new packets in the future used a wrong binary operator,
which makes the check expression always true and accepting too many
packets.
Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Before accessing the TT_RESPONSE packet payload, the node has to ensure that the
packet is long enough as it would expect to be.
Reported-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The TT_RESPONSE skb has to be linearised only if the node plans to access the
packet payload (so only if the message is directed to that node). In all the
other cases the node can avoid this memory operation
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When the translation tables (global and local) are written for debugfs,
it is not neccesary to allocate a buffer, we can directly use
seq_printf() to print them out.
This might actually be safer if the table changes between size
calculation and traversal, and we can't estimate the required size
wrong.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
There are two reasons for this fix:
- the result of choose_orig() and vis_choose() is an index and therefore it can't
be negative. Hence it is correct to make the return type unsigned too.
- sizeof(int) may not be the same on ALL the architectures. Since we plan to use
choose_orig() as DHT hash function, we need to guarantee that, given the same
argument, the result is the same. Then it is correct to explicitly express
the size of the return type (and the second argument). Since the expected
length is currently 4, uint32_t is the most convenient choice.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
get_orig_node() tries to retrieve an orig_node object based on a mac address
and creates it if not present. This is not the wanted behaviour in the
translation table code as we don't want to create new orig_code objects but
expect a NULL pointer if the object does not exist.
Reported-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When deleting the entries, tt_global_del_orig() has to print the message passed
as argument instead of a static one.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Prevent tracing of preempt_disable() in get_cpu_var() in
kvm_clock_read(). When CONFIG_DEBUG_PREEMPT is enabled,
preempt_disable/enable() are traced and this causes the function_graph
tracer to go into an infinite recursion. By open coding the
preempt_disable() around the get_cpu_var(), we can use the notrace
version which prevents preempt_disable/enable() from being traced and
prevents the recursion.
Based on a similar patch for Xen from Jeremy Fitzhardinge.
Tested-by: Gleb Natapov <gleb@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (exynos4_tmu) Fix Kconfig dependency
[ Merging code in-flight, just because I can. What timezone should I
use? - Linus ]
After commit 2a77c46de1
(PM / Suspend: Add statistics debugfs file for suspend to RAM)
a missing pair of braces inside the state_store() function causes even
invalid arguments to suspend to be wrongly treated as failed suspend
attempts. Fix this.
[rjw: Put the hash/subject of the buggy commit into the changelog.]
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
No longer at Citrix, still interested in Xen.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dummy, non-zero definitions for HPAGE_MASK and HPAGE_SIZE were added in
51c6f666fc ("mm: ZAP_BLOCK causes redundant work") to avoid a divide
by zero in generic kernel code.
That code has since been removed, but probably should never have been
added in the first place: we don't want HPAGE_SIZE to act like PAGE_SIZE
for code that is working with hugepages, for example, when the
dependency on CONFIG_HUGETLB_PAGE has not been fulfilled.
Because hugepage size can differ from architecture to architecture, each
is required to have their own definitions for both HPAGE_MASK and
HPAGE_SIZE. This is always done in arch/*/include/asm/page.h.
So, just remove the dummy and dangerous definitions since they are no
longer needed and reveals the correct dependencies. Tested on
architectures using the definitions with allyesconfig: x86 (even with
thp), hppa, mips, powerpc, s390, sh3, sh4, sparc, and sparc64, and with
defconfig on ia64.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
new helper: mount_subtree()
switch create_mnt_ns() to saner calling conventions, fix double mntput() in nfs
btrfs: fix double mntput() in mount_subvol()
