Support for Palm LifeDrive's internal harddrive.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Decouple the HSMMC glue from the twl4030 as the only
regulator provider, using the regulator framework instead.
This makes the glue's "mmc-twl4030" name become a complete
misnomer ... this code could probably all migrate into the
HSMMC driver now.
Tested on 3430SDP (SD and low-voltage MMC) and Beagle (SD),
plus some other boards (including Overo) after they were
converted to set up MMC regulators properly.
Eventually all boards should just associate a regulator with
each MMC controller they use. In some cases (Overo MMC2 and
Pandora MMC3, at least) that would be a fixed-voltage regulator
with no real software control. As a temporary hack (pending
regulator-next updates to make the "fixed.c" regulator become
usable) there's a new ocr_mask field for those boards.
Patch updated with a fix for disabling vcc_aux by
Adrian Hunter <adrian.hunter@nokia.com>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make 770 LCD work by adding clk_add_alias().
Also remove the old unused functions.
Note that the clk_add_alias() could probably be moved
to arch/arm/clkdev.c later on.
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com
This patch is to sync the core linux-omap PM code with mainline. This
code has evolved and been used for a while the linux-omap tree, but
the attempt here is to finally get this into mainline.
Following this will be a series of patches from the 'PM branch' of the
linux-omap tree to add full PM hardware support from the linux-omap
tree.
Much of this PM core code was written by Jouni Hogander with
significant contributions from Paul Walmsley as well as many others
from Nokia, Texas Instruments and linux-omap community.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* 'sh/for-2.6.30' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
video: stop sh_mobile_lcdcfb only if started
sh: ap325 camera without i2c driver fix
Instead of queuing IPMB messages before channel initialization, just
throw them away. Nobody will be listening for them at this point,
anyway, and they will clog up the queue and nothing will be delivered
if we queue them.
Also set the current channel to the number of channels, as this value
is used to tell if the channel information has been initialized.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Ferenc Wagner <wferi@niif.hu>
Cc: Dan Frazier <dannf@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the PCI Device ID 0xc409 to the PCI ID table of via82cxxx.c,
as well as the 0x8409 south bridge ID.
This is required to make the IDE driver work on the VX855/VX875 integrated
chipset.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Bruce Chang <BruceChang@via.com.tw>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Nowadays we (almost) always store the currently executing command
in hwif->cmd so we can use it for the failed opcode reporting.
Cc: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Tuesday 19 May 2009 20:29:28 Martin Lottermoser wrote:
> hdc: cdrom_decode_status: error=0x40 <3>{ LastFailedSense=0x04 }
> ide: failed opcode was: unknown
> hdc: DMA disabled
> ------------[ cut here ]------------
> kernel BUG at drivers/ide/ide-io.c:872!
It is possible for ide-cd to ignore ide_error()'s return value under
some circumstances. Workaround it in ide_intr() and ide_timer_expiry()
by checking if there is a device/port reset pending currently.
Fixes bug #13345:
http://bugzilla.kernel.org/show_bug.cgi?id=13345
Reported-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Reported-and-tested-by: Modestas Vainius <modestas@vainius.eu>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since 2.6.26 we support UDMA66 on ATAPI devices requiring IVB quirk:
commit 8588a2b732
("ide: add SH-S202J to ivb_list[]")
We also later added support for more such devices in:
commit e97564f362
("ide: More TSST drives with broken cable detection")
and in:
commit 3ced5c49bd
("ide: add TSSTcorp CDDVDW SH-S202H to ivb_list[]")
It turns out that such devices lack cable detection altogether
(which in turn results in incorrect detection of 40-wire cables
by our current cable detection strategy) so always handle them
by trusting host-side cable detection only.
v2:
Model detection fixup from Martin.
Reported-and-tested-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch fixes the LCDC driver to avoid calling the
function sh_mobile_lcdc_start_stop(priv, 0) unless the
same function has been called before to start the LCDC
hardware.
Triggered when sh_mobile_lcdcfb.c failed to probe() due to
missing MSTP clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-2.6:
drm: Copy back ioctl data to userspace regardless of return code.
drm: Round size of SHM maps to PAGE_SIZE
The second argument of the probe method points to the amba_id
structure, so it's better passed with the correct type. None of the
current in-tree drivers uses the pointer, so they have only been
checked for a clean compile.
Change suggested by Russell King.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes a regression from commit 9d5b3ffc42
('drm: fixup some of the ioctl function exit paths'): The vblank ioctl
needs to update the userspace parameters when interrupted by a signal,
which was prevented by the return code check. This could cause the X
server to hang in drmWaitVBlank().
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cdrom: beyond ARRAY_SIZE of viocd_diskinfo
xen/blkfront: fix warning when deleting gendisk on unplug/shutdown
xen/blkfront: allow xenbus state transition to Closing->Closed when not Connected
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ipv4: make default for INET_LRO consistent with help text
net: fix skb_seq_read returning wrong offset/length for page frag data
pkt_sched: gen_estimator: use 64 bit intermediate counters for bps
be2net: add two new pci device ids to pci device table
sch_teql: should not dereference skb after ndo_start_xmit()
tcp: fix MSG_PEEK race check
Doc: fixed descriptions on /proc/sys/net/core/* and /proc/sys/net/unix/*
Neterion: *FIFO1_DMA_ERR set twice, should 2nd be *FIFO2_DMA_ERR?
mv643xx_eth: fix PPC DMA breakage
bonding: fix link down handling in 802.3ad mode
bridge: fix initial packet flood if !STP
bridge: relay bridge multicast pkgs if !STP
NET: Meth: Fix unsafe mix of irq and non-irq spinlocks.
mlx4_en: Fix not deleted napi structures
ipconfig: handle case of delayed DHCP server
netpoll: don't dereference NULL dev from np
wimax/i2400m: fix device crash: fix optimization in _roq_queue_update_ws
Currently, userspace can fail to obtain the SAREA mapping (among other
reasons) if it passes SAREA_MAX to drmAddMap without aligning it to the
page size. This breaks for example on PowerPC with 64K pages and radeon
despite the kernel radeon actually doing the right rouding in the first
place.
The way SAREA_MAX is defined with a bunch of ifdef's and duplicated
between libdrm and the X server is gross, ultimately it should be
retrieved by userspace from the kernel, but in the meantime, we have
plenty of existing userspace built with bad values that need to work.
This patch works around broken userspace by rounding the requested size
in drm_addmap_core() of any SHM map to the page size. Since the backing
memory for SHM maps is also allocated within addmap_core, there is no
danger of adjacent memory being exposed due to the increased map size.
The only side effect is that drivers that previously tried to create or
access SHM maps using a size < PAGE_SIZE and failed (getting -EINVAL),
will now succeed at the cost of a little bit more memory used if that
happens to be when the map is created.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
get_event_name uses sprintf to fill a buffer declared on the stack. It fills
the buffer 2 bytes at a time. What the code doesn't take into account is that
sprintf(buf, "%02x", data) actually writes 3 bytes. 2 bytes for the data and
then it nul terminates the string. Since we declare buf to be 40 characters
long and then we write 40 bytes of data into buf sprintf is going to write 41
characters. The fix is to leave room in buf for the nul terminator.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Recent PCI PM changes introduced a bug that causes some devices to be
mishandled after kexec and during early initialization. The failure
scenario in the kexec case is the following:
* Assume a PCI device is not power-manageable by the platform and has
PCI_PM_CTRL_NO_SOFT_RESET set in PMCSR.
* The device is put into D3 before kexec (using the native PCI PM).
* After kexec, pci_setup_device() sets the device's power state to
PCI_UNKNOWN.
* pci_set_power_state(dev, PCI_D0) is called by the device's driver.
* __pci_start_power_transition(dev, PCI_D0) is called and since the
device is not power-manageable by the platform, it causes
pci_update_current_state(dev, PCI_D0) to be called. As a result
the device's current_state field is updated to PCI_D3, in
accordance with the contents of its PCI PM registers.
* pci_raw_set_power_state() is called and it changes the device power
state to D0. *However*, it should also call pci_restore_bars() to
reinitialize the device, but it doesn't, because the device's
current_state field has been modified earlier.
To prevent this from happening, modify pci_platform_power_transition()
so that it doesn't use pci_update_current_state() to update the
current_state field for devices that aren't power-manageable by the
platform. Instead, this field should be updated directly for devices
that don't support the native PCI PM.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Without this change Openmoko Freerunner (GTA02) bootstrap will deadlock.
As pointed out in other patches this issue is in the wild since the merge
of:
: commit 3aa551c9b4
: Author: Thomas Gleixner <tglx@linutronix.de>
: Date: Mon Mar 23 18:28:15 2009 +0100
:
: genirq: add threaded interrupt handler support
:
: Add support for threaded interrupt handlers
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <balajirrao@openmoko.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Due to the way that the WM8350 audio driver handles CODEC_ENA many of
the WM8350 audio registers are marked as volatile when they aren't
actually so. Allow the audio driver to see a cache of these values for
inspection during interrupt context.
To do this we need to stop satisfying any bits from volatile registers
from cache - there's no real benefit from doing so anyway, we did the
read already.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Martin Knoblauch reports that trying to build 2.6.30-rc6-git3 with
RHEL4.3 userspace (gcc (GCC) 3.4.5 20051201 (Red Hat 3.4.5-2)) causes an
internal compiler error (ICE):
drivers/char/random.c: In function `get_random_int':
drivers/char/random.c:1672: error: unrecognizable insn:
(insn 202 148 150 0 /scratch/build/linux-2.6.30-rc6-git3/arch/x86/include/asm/tsc.h:23 (set (reg:SI 0 ax [91])
(subreg:SI (plus:DI (plus:DI (reg:DI 0 ax [88])
(subreg:DI (reg:SI 6 bp) 0))
(const_int -4 [0xfffffffffffffffc])) 0)) -1 (nil)
(nil))
drivers/char/random.c:1672: internal compiler error: in extract_insn, at recog.c:2083
and after some debugging it turns out that it's due to the code trying
to figure out the rough value of the current stack pointer by taking an
address of an uninitialized variable and casting that to an integer.
This is clearly a compiler bug, but it's not worth fighting - while the
current stack kernel pointer might be somewhat hard to predict in user
space, it's also not generally going to change for a lot of the call
chains for a particular process.
So just drop it, and mumble some incoherent curses at the compiler.
Tested-by: Martin Knoblauch <spamtrap@knobisoft.de>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently blkfront gives a warning when hot unplugging due to calling
del_gendisk() with interrupts disabled (due to blkif_io_lock).
WARNING: at kernel/softirq.c:124 local_bh_enable+0x36/0x84()
Modules linked in: xenfs xen_netfront ext3 jbd mbcache xen_blkfront
Pid: 13, comm: xenwatch Not tainted 2.6.29-xs5.5.0.13 #3
Call Trace:
[<c012611c>] warn_slowpath+0x80/0xb6
[<c0104cf1>] xen_sched_clock+0x16/0x63
[<c0104710>] xen_force_evtchn_callback+0xc/0x10
[<c0104e32>] check_events+0x8/0xe
[<c0104d9b>] xen_restore_fl_direct_end+0x0/0x1
[<c0103749>] xen_mc_flush+0x10a/0x13f
[<c0105bd2>] __switch_to+0x114/0x14e
[<c011d92b>] dequeue_task+0x62/0x70
[<c0123b6f>] finish_task_switch+0x2b/0x84
[<c0299877>] schedule+0x66d/0x6e7
[<c0104710>] xen_force_evtchn_callback+0xc/0x10
[<c0104710>] xen_force_evtchn_callback+0xc/0x10
[<c012a642>] local_bh_enable+0x36/0x84
[<c022f9a7>] sk_filter+0x57/0x5c
[<c0233dae>] netlink_broadcast+0x1d5/0x315
[<c01c6371>] kobject_uevent_env+0x28d/0x331
[<c01e7ead>] device_del+0x10f/0x120
[<c01e7ec6>] device_unregister+0x8/0x10
[<c015f86d>] bdi_unregister+0x2d/0x39
[<c01bf6f4>] unlink_gendisk+0x23/0x3e
[<c01ac946>] del_gendisk+0x7b/0xe7
[<d0828c19>] blkfront_closing+0x28/0x6e [xen_blkfront]
[<d082900c>] backend_changed+0x3ad/0x41d [xen_blkfront]
We can fix this by calling del_gendisk() later in blkfront_closing, after
releasing blkif_io_lock. Since the queue is stopped during the interrupts
disabled phase I don't think there is any danger of an event occuring between
releasing the blkif_io_lock and deleting the disk.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This situation can occur when attempting to attach a block device whose
backend is an empty physical CD-ROM driver. The backend in this case
will go directly from the Initialising state to Closing->Closed.
Previously this would result in a NULL pointer deref on info->gd
(xenbus_dev_fatal does not return as a1a15ac5 seems to expect)
Cc: stable@kernel.org
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
In Commit
commit 3b8b5c9b1f
Author: Eric Moore <eric.moore@lsi.com>
Date: Tue Apr 21 15:44:27 2009 -0600
[SCSI] mpt2sas : bump driver version to 01.100.02.00
The MPT2SAS_MAJOR_VERSION didn't get bumped from 00 to 01 so
applications will see it incorrectly as 00.100.02.00 driver instead of
01.100.02.00. Fix by making MPT2SAS_MAJOR_VERSION match the major
number in MPT2SAS_DRIVER_VERSION
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit c45d6320 ("fix reference counting of ftdi_private") stopped
ftdi_sio_port_remove() from directly freeing the port-private data, with
the intention if the port was still open, it would be freed when
ftdi_close() is eventually called and releases the last refcount on the
structure.
That's all very well, but ftdi_sio_port_remove() still contains a call
to usb_set_serial_port_data(port, NULL) -- so by the time we get to
ftdi_close() for the port which was unplugged, it _still_ oopses on
dereferencing that NULL pointer, as it did before (and does in 2.6.29).
The fix is just not to clear the private data in ftdi_sio_port_remove().
Then the refcount is properly reduced to zero when the final kref_put()
happens in ftdi_close().
Remove a bogus comment too, while we're at it. And stop doing things
inside "if (priv)" -- it must _always_ be there.
Based loosely on an earlier patch by Daniel Mack, and suggestions by
Alan Stern.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 5b7f3a50 (fix dataflash 64-bit divisions) unfortunately
introduced a typo. Erase addr and len were swapped in the pageaddr
calculation, causing the wrong sectors to get erased.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Liam Girdwood <lrg@slimlogic.co.uk>
CC: Mike Rapoport <mike@compulab.co.il>
CC: Eric Miao <eric.miao@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Alessandro Rubini
Marek Vašut
Russell King
Tony Lindgren
David Brownell
Andrew de Quincey
Kevin Hilman
Krzysztof Hałasa
Linus Torvalds
Breno Leitao
Corey Minyard
Harald Welte
Bartlomiej Zolnierkiewicz
Magnus Damm
Michel Dänzer
Roel Kluin
Benjamin Herrenschmidt
Eric Paris
Rafael J. Wysocki
Nelson Castillo
Mark Brown
Ian Campbell
Ajit Khaparde
Eric Moore
David Woodhouse
Peter Korsgaard
Mike Frysinger