TI shared transport driver previously intended to expose rfkill
entries for each of the protocol gpio that the chip would have.
However now in case such gpios exist, which requires to be enabled
for a specific protocol, the responsibility lay on protocol driver.
This patch removes the request/free of multiple gpios, rfkill struct
references and also removes the chip_toggle function.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Where file-transfer stops/pauses in between, is
result of a HCI-LL anamoly in ST LL driver.
ST LL did not copy the contents of WaitQ into the TxQ, when a WAKEUP_IND
collision happened.
Make also sure, that the copying mechanism is safe, by wrapping it around
spin locks inside st_int_recv().
This was easily reproduced when the sleep timeout was reduced to 100ms
for HCI-LL.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To fasten the process of firmware download, the chip allows
disabling of the command complete event generation from host.
In these cases, only few very essential commands would have
the command complete events and hence the wait associated with
them.
So now the driver would wait for a command complete event, only
when it comes across a wait event during firmware parsing.
This would also mean we need to skip not just the change baud
rate command but also the wait for it.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pr_debug-ing few pr_infos from the data paths such as tty receive and
write so as to reduce debugs when we have higher logging levels enabled
undef VERBOSE in receive to avoid huge logs when log level 8 is set.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
set-right the error codes that the shared transport driver
returns.
Instead of magic numbers like -1, return relevant codes such as
ETIMEDOUT or EIO, EAGAIN when wait times out or uart write bytes don't
match expected value or when registration fails and needs to be
attempted again.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The communication between ST KIM and UIM was interfaced
over the /dev/rfkill device node.
Move the interface to a simpler less abusive sysfs entry
mechanism and document it in Documentation/ABI/testing/
under sysfs-platform-kim.
Shared transport driver would now read the UART details
originally received by bootloader or firmware as platform
data.
The data read will be shared over sysfs entries for the user-space
UIM or other n/w manager/plugins to be read, and assist the driver
by opening up the UART, setting the baud-rate and installing the
line discipline.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The architecture of shared transport had begun with individual
protocols like bluetooth, fm and gps telling the shared transport
what sort of protocol they are and then expecting the ST driver
to parse the incoming data from chip and forward data only
relevant to the protocol drivers.
This change would mean each protocol drivers would also send
information to ST driver as to how to intrepret their protocol
data coming out of the chip.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original macro worked only when applied to variables named 'dev'.
While this could have been fixed by simply renaming the macro argument,
a more type-safe replacement by an inline function is preferred.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As a follow-on to the recent patches I submitted that allowed for a sysfs
memory block to span multiple memory sections, we should also update the
probe routine to online all of the memory sections in a memory block. Without
this patch the current code will only add a single memory section. I think
the probe routine should add all of the memory sections in the specified memory
block so that its behavior is in line with memory hotplug actions through
the sysfs interfaces.
This patch applies on top of the previous sysfs memory updates to allow
a sysfs directory o span multiple memory sections.
https://lkml.org/lkml/2011/1/20/245
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the 'phys_index' property of a the memory_block struct to be
called start_section_nr, and add a end_section_nr property. The
data tracked here is the same but the updated naming is more in line
with what is stored here, namely the first and last section number
that the memory block spans.
The names presented to userspace remain the same, phys_index for
start_section_nr and end_phys_index for end_section_nr, to avoid breaking
anything in userspace.
This also updates the node sysfs code to be aware of the new capability for
a memory block to contain multiple memory sections and be aware of the memory
block structure name changes (start_section_nr). This requires an additional
parameter to unregister_mem_sect_under_nodes so that we know which memory
section of the memory block to unregister.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Reviewed-by: Robin Holt <holt@sgi.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the memory sysfs code such that each sysfs memory directory is now
considered a memory block that can span multiple memory sections per
memory block. The default size of each memory block is SECTION_SIZE_BITS
to maintain the current behavior of having a single memory section per
memory block (i.e. one sysfs directory per memory section).
For architectures that want to have memory blocks span multiple
memory sections they need only define their own memory_block_size_bytes()
routine.
Update the memory hotplug documentation to reflect the new behaviors of
memory blocks reflected in sysfs.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Reviewed-by: Robin Holt <holt@sgi.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add ML7213 device information.
ML7213 is companion chip of Intel Atom E6xx series for IVI(In-Vehicle Infotainment).
ML7213 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When encountering an error while executing the driver's ->add method, we
should cancel registration and unwind what we've regged so far. The low
level ->add methods do return proper error codes but those aren't looked
at in sysdev_driver_register(). Fix that by sharing the unregistering
code.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use gcc's __func__ instead of the function name.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some place in firmware_class.c using "int uevent" define, but others use "bool
uevent".
This patch replace all int uevent define to bool.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add text, courtesy of Kay Sievers, that provides some background on
device_rename() and why it shouldn't be used.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (42 commits)
usb: gadget: composite: avoid access beyond array max length
USB: serial: handle Data Carrier Detect changes
USB: gadget: Fix endpoint representation in ci13xxx_udc
USB: gadget: Fix error path in ci13xxx_udc gadget probe function
usb: pch_udc: Fix the worning log issue at gadget driver remove
USB: serial: Updated support for ICOM devices
USB: ehci-mxc: add work-around for efika mx/sb bug
USB: unbreak ehci-mxc on otg port of i.MX27
drivers: update to pl2303 usb-serial to support Motorola cables
USB: adding USB support for Cinterion's HC2x, EU3 and PH8 products
USB serial: add missing .usb_driver field in serial drivers
USB: ehci-fsl: Fix 'have_sysif_regs' detection
USB: g_printer: fix bug in module parameter definitions
USB: g_printer: fix bug in unregistration
USB: uss720: remove duplicate USB device
MAINTAINERS: add ueagle-atm entry
USB: EHCI: fix DMA deallocation bug
USB: pch_udc: support new device ML7213 IOH
usb: pch_udc: Fixed issue which does not work with g_serial
usb: set ep_dev async suspend should be later than device_initialize
...
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (26 commits)
staging: r8712u: Add new device IDs
staging: brcm80211: fix suspend/resume issue in brcmsmac
staging: brcm80211: remove assert to avoid panic since 2.6.37 kernel
Staging: iio: Aditional fixpoint formatted output bugfix
staging: usbip: vhci: use urb->dev->portnum to find port
staging: usbip: vhci: handle EAGAIN from SO_RCVTIMEO
staging: usbip: vhci: friendly log messages for connection errors
staging: usbip: vhci: refuse to enqueue for dead connections
staging: usbip: vhci: give back URBs from in-flight unlink requests
staging: usbip: vhci: update reference count for usb_device
staging: usbip: stub: update refcounts for devices and interfaces
staging: tidspbridge: replace mbox callback with notifier_call
staging: comedi: ni_labpc: Use shared IRQ for PCMCIA card
Staging: speakup: &&/|| confusion in silent_store()
iio: Fixpoint formatted output bugfix
staging: rt2860: Fix incorrect netif_stop_queue usage warning
staging: r8712u: Fix memory leak in firmware loading
staging: tidspbridge: configure full L1 MMU range
staging: rt2870sta: Add ID for Linksys WUSB100v2
Staging: xgfib: put parenthesis in the right place
...
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty/serial: fix apbuart build
n_hdlc: fix read and write locking
serial: unbreak billionton CF card
tty: use for_each_console() and WARN() on sysfs failures
vt: fix issue when fbcon wants to takeover a second time.
Fix up trivial conflict in drivers/tty/tty_io.c
We should not report incomplete blocks on error. Return the number of
bytes successfully transferred, rounded down to the nearest block.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When we encounter an error, make sure we complete the transaction
otherwise we'll leave the request dangling.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do not respond with -EINVAL to EVIOCGKEYCODE for not-yet-mapped
scancodes, but rather return KEY_RESERVED.
This fixes breakage with Ubuntu's input-kbd utility that stopped
returning full keymaps for remote controls.
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Mark Lord <kernel@teksavvy.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: set queue DMA alignment to sector size for ATAPI too
libata: DVR-212D can't do SETXFER DVD-RW DVR-212D
ahci: add HFLAG_YES_FBS and apply it to 88SE9128
pata_hpt37x: inherit prereset() method for HPT374
ahci: AHCI mode SATA patch for Intel DH89xxCC DeviceIDs
pata_hpt37x: fold 'if' statement into 'switch'
pata_hpt{37x|3x2n}: use pr_*(DRV_NAME ...) instead of printk(KERN_* ...)
pata_hpt{366|37x}: use pr_warning(...) instead of printk(KERN_WARNING ...)
pata_mpc52xx: inherit from ata_bmdma_port_ops
This reverts commit a121f64399.
Unfortunately, this commit breaks UBIFS backward compatibility and
makes new UBIFS refuse older UBIFS-formatted media:
UBIFS error: validate_sb: min. I/O unit mismatch: 8 in superblock, 64 real
Thus, we have to revert this patch and work on a better solution.
Reported-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
On some machines, like Dell Studio XPS 16 (1640), touchpad fails to
respond to the standard query after first reset but may start
responding later, so let's repeat reset sequence several (3) times.
Signed-off-by: Alexandre Peixoto Ferreira <alexandref75@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
synaptics_set_advanced_gesture_mode() affect capabilities bits we should
perform comparison after calling this function, otherwise they will never
match and we will be forced to perform full reconnect.
Signed-off-by: Alexandre Peixoto Ferreira <alexandref75@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
ata_pio_sectors() expects buffer for each sector to be contained in a
single page; otherwise, it ends up overrunning the first page. This
is achieved by setting queue DMA alignment. If sector_size is smaller
than PAGE_SIZE and all buffers are sector_size aligned, buffer for
each sector is always contained in a single page.
This wasn't applied to ATAPI devices but IDENTIFY_PACKET is executed
as ATA_PROT_PIO and thus uses ata_pio_sectors(). Newer versions of
udev issue IDENTIFY_PACKET with unaligned buffer triggering the
problem and causing oops.
This patch fixes the problem by setting sdev->sector_size to
ATA_SECT_SIZE on ATATPI devices and always setting DMA alignment to
sector_size. While at it, add a warning for the unlikely but still
possible scenario where sector_size is larger than PAGE_SIZE, in which
case the alignment wouldn't be enough.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: John Stanley <jpsinthemix@verizon.net>
Tested-by: John Stanley <jpsinthemix@verizon.net>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PIONEER DVR-212D can't do SETXFER like its sibling DVRTD08. Add
ATA_HORKAGE_NOSETXFER for it. Reported in bko#27502.
https://bugzilla.kernel.org/show_bug.cgi?id=27502
Signed-off-by: Francesco Antonacci <fraanto@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 5f173107ec added HFLAG_YES_FBS workaround for 88SE9128
(1b4b:9123).
However, that change inadvertently caused the legacy IDE interface of
the controller (with the same pci id) to become associated with the AHCI
driver as well, causing the driver to try to bring the interface up in
vain.
Fix that by matching against class as well.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit ab81a505ae (pata_hpt37x: unify ->pre_reset
methods) neglected to remove the initializer for the prereset() method from
'hpt374_fn1_port_ops' (it's inherited from 'hpt372_port_ops' anyway), as well
as to update the comment in hpt37x_init_one()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the AHCI-mode SATA DeviceID for the Intel DH89xxCC PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
hpt37x_init_one() has a large *if* statement which should really be folded into
the *switch* statement that currently constitutes its *else* branch, reducing
one level of indentation...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
... the same as the 'pata_hpt366' driver does.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
pata_mpc52xx supports BMDMA but inherits ata_sff_port_ops which
triggers BUG_ON() when a DMA command is issued. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Roman Fietze <roman.fietze@telemotive.de>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/nv50: fix regression on IGPs
drm/radeon/kms: re-emit full context state for evergreen blits
drm/radeon/kms: release CMASK access in preclose_kms
drm/radeon/kms: fix r6xx+ scanout on BE systems
drm/radeon/kms: clean up some magic numbers
drm/radeon/kms: only enable HDMI mode if radeon audio is enabled
radeon/kms: fix dp displayport mode validation
drm/nvc0/grctx: correct an off-by-one
drm/nv50: Fix race with PFIFO during PGRAPH context destruction.
drm/nouveau: Workaround incorrect DCB entry on a GeForce3 Ti 200.
drm/nvc0: implement irq handler for whatever's at 0x14xxxx
drm/nvc0: fix incorrect TPC register setup
drm/nouveau: probe for adt7473 before f75375
drm/nouveau: remove dead function definition
clear state doesn't seem to work properly in some cases
Fixes hangs in heavy 3D on some evergreen cards reported on
IRC.
May fix:
https://bugs.freedesktop.org/show_bug.cgi?id=33381
possibly others.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@gmail.com>
The MMCIDATACNT register contain the number of byte left at error
not the number of words, so loose the << 2 thing. Further if CRC
fails on the first block, we may end up with a negative number
of transferred bytes which is not good, and the formula was in
wrong order.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pavan Savoy
Ferenc Wagner
Nathan Fontenot
Tomoya MORINAGA
Borislav Petkov
Bob Liu
Timur Tabi
Linus Torvalds
Russell King
Dmitry Torokhov
Huang Weiyi
Artem Bityutskiy
Alexandre Peixoto Ferreira
Rakesh Iyer
Jeff Garzik
Tejun Heo
Francesco Antonacci
Anssi Hannula
Sergei Shtylyov
Seth Heasley
Tejun Heo
Dave Airlie
Ben Skeggs
Alex Deucher
Marek Olšák
Linus Walleij