Use for_each_populated_zone() instead of for_each_zone() in hibernation
code. This fixes a bug on s390, where we allow both config options
HIBERNATION and MEMORY_HOTPLUG, so that we also have a ZONE_MOVABLE
here. We only allow hibernation if no memory hotplug operation was
performed, so in fact both features can only be used exclusively, but
this way we don't need 2 differently configured (distribution) kernels.
If we have an unpopulated ZONE_MOVABLE, we allow hibernation but run
into a BUG_ON() in memory_bm_test/set/clear_bit() because hibernation
code iterates through all zones, not only the populated zones, in
several places. For example, swsusp_free() does for_each_zone() and
then checks for pfn_valid(), which is true even if the zone is not
populated, resulting in a BUG_ON() later because the pfn cannot be
found in the memory bitmap.
Replacing all occurences of for_each_zone() in hibernation code with
for_each_populated_zone() would fix this issue.
[rjw: Rebased on top of linux-next hibernation patches.]
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
We want to avoid attempting to free too much memory too hard during
hibernation, so estimate the minimum size of the image to use as the
lower limit for preallocating memory.
The approach here is based on the (experimental) observation that we
can't free more page frames than the sum of:
* global_page_state(NR_SLAB_RECLAIMABLE)
* global_page_state(NR_ACTIVE_ANON)
* global_page_state(NR_INACTIVE_ANON)
* global_page_state(NR_ACTIVE_FILE)
* global_page_state(NR_INACTIVE_FILE)
minus
* global_page_state(NR_FILE_MAPPED)
Namely, if this number is subtracted from the number of saveable
pages in the system, we get a good estimate of the minimum reasonable
size of a hibernation image.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Since the hibernation code is now going to use allocations of memory
to make enough room for the image, it can also use the page frames
allocated at this stage as image page frames. The low-level
hibernation code needs to be rearranged for this purpose, but it
allows us to avoid freeing a great number of pages and allocating
these same pages once again later, so it generally is worth doing.
[rev. 2: Take highmem into account correctly.]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Rework swsusp_shrink_memory() so that it calls shrink_all_memory()
just once to make some room for the image and then allocates memory
to apply more pressure to the memory management subsystem, if
necessary.
Unfortunately, we don't seem to be able to drop shrink_all_memory()
entirely just yet, because that would lead to huge performance
regressions in some test cases.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Although the same label name is used somewhere else in the file, this
particular label was consistently typoed in all of its uses.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Introduce a core framework for run-time power management of I/O
devices. Add device run-time PM fields to 'struct dev_pm_info'
and device run-time PM callbacks to 'struct dev_pm_ops'. Introduce
a run-time PM workqueue and define some device run-time PM helper
functions at the core level. Document all these things.
Special thanks to Alan Stern for his help with the design and
multiple detailed reviews of the pereceding versions of this patch
and to Magnus Damm for testing feedback.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@igel.co.jp>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, the following scenario appears to be possible in theory:
* Tasks are frozen for hibernation or suspend.
* Free pages are almost exhausted.
* Certain piece of code in the suspend code path attempts to allocate
some memory using GFP_KERNEL and allocation order less than or
equal to PAGE_ALLOC_COSTLY_ORDER.
* __alloc_pages_internal() cannot find a free page so it invokes the
OOM killer.
* The OOM killer attempts to kill a task, but the task is frozen, so
it doesn't die immediately.
* __alloc_pages_internal() jumps to 'restart', unsuccessfully tries
to find a free page and invokes the OOM killer.
* No progress can be made.
Although it is now hard to trigger during hibernation due to the memory
shrinking carried out by the hibernation code, it is theoretically
possible to trigger during suspend after the memory shrinking has been
removed from that code path. Moreover, since memory allocations are
going to be used for the hibernation memory shrinking, it will be even
more likely to happen during hibernation.
To prevent it from happening, introduce the oom_killer_disabled switch
that will cause __alloc_pages_internal() to fail in the situations in
which the OOM killer would have been called and make the freezer set
this switch after tasks have been successfully frozen.
[akpm@linux-foundation.org: be nicer to the namespace]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Fengguang Wu <fengguang.wu@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The *_nvs_* routines in swsusp.c make use of the io*map()
functions, which are only provided for HAS_IOMEM, thus
breaking compilation if HAS_IOMEM is not set. Fix this
by moving the *_nvs_* routines into hibernate_nvs.c, which
is only compiled if HAS_IOMEM is set.
[rjw: Change the name of the new file to hibernate_nvs.c, add the
license line to the header comment.]
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Change the name of kernel/power/disk.c to kernel/power/hibernate.c
in analogy with the file names introduced by the changes that
separated the suspend to RAM and standby funtionality from the
common PM functions.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Move the suspend to RAM and standby code from kernel/power/main.c
to two separate files, kernel/power/suspend.c containing the basic
functions and kernel/power/suspend_test.c containing the automatic
suspend test facility based on the RTC clock alarm.
There are no changes in functionality related to these modifications.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
A future patch is going to modify the memory shrinking code so that
it will make memory allocations to free memory instead of using an
artificial memory shrinking mechanism for that. For this purpose it
is convenient to move swsusp_shrink_memory() from
kernel/power/swsusp.c to kernel/power/snapshot.c, because the new
memory-shrinking code is going to use things that are local to
kernel/power/snapshot.c .
[rev. 2: Make some functions static and remove their headers from
kernel/power/power.h]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Remove the shrinking of memory from the suspend-to-RAM code, where
it is not really necessary.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
This patch (as1241) renames a bunch of functions in the PM core.
Rather than go through a boring list of name changes, suffice it to
say that in the end we have a bunch of pairs of functions:
device_resume_noirq dpm_resume_noirq
device_resume dpm_resume
device_complete dpm_complete
device_suspend_noirq dpm_suspend_noirq
device_suspend dpm_suspend
device_prepare dpm_prepare
in which device_X does the X operation on a single device and dpm_X
invokes device_X for all devices in the dpm_list.
In addition, the old dpm_power_up and device_resume_noirq have been
combined into a single function (dpm_resume_noirq).
Lastly, dpm_suspend_start and dpm_resume_end are the renamed versions
of the former top-level device_suspend and device_resume routines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Rename the functions performing "_noirq" dev_pm_ops
operations from device_power_down() and device_power_up()
to device_suspend_noirq() and device_resume_noirq().
The new function names are chosen to show that the functions
are responsible for calling the _noirq() versions to finalize
the suspend/resume operation. The current function names do
not perform power down/up anymore so the names may be misleading.
Global function renames:
- device_power_down() -> device_suspend_noirq()
- device_power_up() -> device_resume_noirq()
Static function renames:
- suspend_device_noirq() -> __device_suspend_noirq()
- resume_device_noirq() -> __device_resume_noirq()
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Len Brown <lenb@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
We shouldn't hold dpm_list_mtx while executing
[disable|enable]_nonboot_cpus(), because theoretically this may lead
to a deadlock as shown by the following example (provided by Johannes
Berg):
CPU 3 CPU 2 CPU 1
suspend/hibernate
something:
rtnl_lock() device_pm_lock()
-> mutex_lock(&dpm_list_mtx)
mutex_lock(&dpm_list_mtx)
linkwatch_work
-> rtnl_lock()
disable_nonboot_cpus()
-> flush CPU 3 workqueue
Fortunately, device drivers are supposed to stop any activities that
might lead to the registration of new device objects way before
disable_nonboot_cpus() is called, so it shouldn't be necessary to
hold dpm_list_mtx over the entire late part of device suspend and
early part of device resume.
Thus, during the late suspend and the early resume of devices acquire
dpm_list_mtx only when dpm_list is going to be traversed and release
it right after that.
This patch is reported to fix the regressions tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=13245.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Miles Lane <miles.lane@gmail.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Check the return value of sysdev_suspend(). I think this was a typo.
Without this change, the following "if" check is always false.
I also changed the error message so it's distinguishable from the
similar message a few lines above.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Commit c751085943 ("PM/Hibernate: Wait for
SCSI devices scan to complete during resume") added a call to
scsi_complete_async_scans() to software_resume(), so that it waited for
the SCSI scanning to complete, but the call was added at a wrong place.
Namely, it should have been added after wait_for_device_probe(), which
is called only if the image partition hasn't been specified yet. Also,
it's reasonable to check if the image partition is present and only wait
for the device probing and SCSI scanning to complete if it is not the
case.
Additionally, since noresume is checked right at the beginning of
software_resume() and the function returns immediately if it's set, it
doesn't make sense to check it once again later.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 900af0d973 (PM: Change suspend
code ordering) changed the ordering of suspend code in such a way
that the platform .prepare() callback is now executed after the
device drivers' late suspend callbacks have run. Unfortunately, this
turns out to break ARM platforms that need to talk via I2C to power
control devices during the .prepare() callback.
For this reason introduce two new platform suspend callbacks,
.prepare_late() and .wake(), that will be called just prior to
disabling non-boot CPUs and right after bringing them back on line,
respectively, and use them instead of .prepare() and .finish() for
ACPI suspend. Make the PM core execute the .prepare() and .finish()
platform suspend callbacks where they were executed previously (that
is, right after calling the regular suspend methods provided by
device drivers and right before executing their regular resume
methods, respectively).
It is not necessary to make analogous changes to the hibernation
code and data structures at the moment, because they are only used
by ACPI platforms.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Len Brown <len.brown@intel.com>
There is a race between resume from hibernation and the asynchronous
scanning of SCSI devices and to prevent it from happening we need to
call scsi_complete_async_scans() during resume from hibernation.
In addition, if the resume from hibernation is userland-driven, it's
better to wait for all device probes in the kernel to complete before
attempting to open the resume device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
Make the following header file changes:
- remove arch ifdefs and asm/suspend.h from linux/suspend.h
- add asm/suspend.h to disk.c (for arch_prepare_suspend())
- add linux/io.h to swsusp.c (for ioremap())
- x86 32/64 bit compile fixes
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: cleanup
In almost cases, for_each_zone() is used with populated_zone(). It's
because almost function doesn't need memoryless node information.
Therefore, for_each_populated_zone() can help to make code simplify.
This patch has no functional change.
[akpm@linux-foundation.org: small cleanup]
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the ordering of the hibernation core code so that the platform
"prepare" callbacks are executed and the nonboot CPUs are disabled
after calling device drivers' "late suspend" methods.
This change (along with the previous analogous change of the suspend
core code) will allow us to rework the PCI PM core so that the power
state of devices is changed in the "late" phase of suspend (and
analogously in the "early" phase of resume), which in turn will allow
us to avoid the race condition where a device using shared interrupts
is put into a low power state with interrupts enabled and then an
interrupt (for another device) comes in and confuses its driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Change the ordering of the suspend core code so that the platform
"prepare" callback is executed and the nonboot CPUs are disabled
after calling device drivers' "late suspend" methods.
This change will allow us to rework the PCI PM core so that the power
state of devices is changed in the "late" phase of suspend (and
analogously in the "early" phase of resume), which in turn will allow
us to avoid the race condition where a device using shared interrupts
is put into a low power state with interrupts enabled and then an
interrupt (for another device) comes in and confuses its driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Use the functions introduced in by the previous patch,
suspend_device_irqs(), resume_device_irqs() and check_wakeup_irqs(),
to rework the handling of interrupts during suspend (hibernation) and
resume. Namely, interrupts will only be disabled on the CPU right
before suspending sysdevs, while device drivers will be prevented
from receiving interrupts, with the help of the new helper function,
before their "late" suspend callbacks run (and analogously during
resume).
In addition, since the device interrups are now disabled before the
CPU has turned all interrupts off and the CPU will ACK the interrupts
setting the IRQ_PENDING bit for them, check in sysdev_suspend() if
any wake-up interrupts are pending and abort suspend if that's the
case.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Move the sysdev_suspend/resume from the callee to the callers, with
no real change in semantics, so that we can rework the disabling of
interrupts during suspend/hibernation.
This is based on an earlier patch from Linus.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* hibernate:
PM: Fix suspend_console and resume_console to use only one semaphore
PM: Wait for console in resume
PM: Fix pm_notifiers during user mode hibernation
swsusp: clean up shrink_all_zones()
swsusp: dont fiddle with swappiness
PM: fix build for CONFIG_PM unset
PM/hibernate: fix "swap breaks after hibernation failures"
PM/resume: wait for device probing to finish
Consolidate driver_probe_done() loops into one place
Avoids later waking up to a blinking cursor if the device woke up and
returned to sleep before the console switch happened.
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Snapshot device is opened with O_RDONLY during suspend and O_WRONLY durig
resume. Make sure we also call notifiers with correct parameter telling
them what we are really doing.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Compilation of kprobes.c with CONFIG_PM unset is broken due to some broken
config dependncies. Fix that.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Reported-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
the resume code does not currently wait for device probing to finish.
Even without async function calls this is dicey and not correct,
but with async function calls during the boot sequence this is going
to get hit more...
This patch adds the synchronization using the newly introduced helper.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: fix deadlock in blk_abort_queue() for drivers that readd to timeout list
block: fix booting from partitioned md array
block: revert part of 18ce3751cc
cciss: PCI power management reset for kexec
paride/pg.c: xs(): &&/|| confusion
fs/bio: bio_alloc_bioset: pass right object ptr to mempool_free
block: fix bad definition of BIO_RW_SYNC
bsg: Fix sense buffer bug in SG_IO
Compilation of kprobes.c with CONFIG_PM unset is broken due to some broken
config dependncies. Fix that.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can't OR shift values, so get rid of BIO_RW_SYNC and use BIO_RW_SYNCIO
and BIO_RW_UNPLUG explicitly. This brings back the behaviour from before
213d9417fe.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Introduce boolean function system_entering_hibernation() returning
'true' during the last phase of hibernation, in which devices are
being put into low power states and the sleep state (for example,
ACPI S4) is finally entered.
Some device drivers need such a function to check if the system is
in the final phase of hibernation. In particular, some SATA drivers
are going to use it for blacklisting systems in which the disks
should not be spun down during the last phase of hibernation (the
BIOS will do that anyway).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reorder the code in kernel/power/main.c to fix compilation warning
triggered by unsetting CONFIG_SUSPEND.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Freezer fails to compile if with the following configuration
settings:
CONFIG_CGROUPS=y
CONFIG_CGROUP_FREEZER=y
CONFIG_MODULES=y
CONFIG_FREEZER=y
CONFIG_PM=y
CONFIG_PM_SLEEP=n
Fix this by making process.o compilation depend on CONFIG_FREEZER.
Reported-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Impact: Reduce stack usage, use new cpumask API.
Mainly changing cpumask_t to 'struct cpumask' and similar simple API
conversion. Two conversions worth mentioning:
1) we use cpumask_any_but to avoid a temporary in kernel/softlockup.c,
2) Use cpumask_var_t in taskstats_user_cmd().
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Replace one evaluation of pfn_to_page() in copy_data_pages() with
the value of a local variable containing the right number already.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
It has been requested to make hibernation work with memory
hotplugging enabled and for this purpose the hibernation code has to
be reworked to take the possible overlapping of zones into account.
Thus, rework the hibernation memory bitmaps code to prevent
duplication of PFNs from occuring and add checks to make sure that
one page frame will not be marked as saveable many times.
Additionally, use list.h lists instead of open-coded lists to
implement the memory bitmaps.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
During resume from hibernation using the userland interface image
data are being passed from the used space process to the kernel.
These data need not be valid, but currently the kernel sometimes
oopses if it gets invalid image data, which is wrong. Make the
kernel return error codes to the user space in such cases.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
According to the ACPI Specification 3.0b, Section 15.3.2,
"OSPM will call the _PTS control method some time before entering a
sleeping state, to allow the platform's AML code to update this
memory image before entering the sleeping state. After the system
awakes from an S4 state, OSPM will restore this memory area and call
the _WAK control method to enable the BIOS to reclaim its memory
image." For this reason, implement a mechanism allowing us to save
the NVS memory during hibernation and to restore it during the
subsequent resume.
Based on a patch by Zhang Rui.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Call platform_begin() before swsusp_shrink_memory() so that we can
always allocate enough memory to save the ACPI NVS region from
platform_begin().
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
it had been put there to mark the call of blkdev_put() that
needed proper argument propagated to it; later patch in the
same series had done just that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Impact: widen function-tracing to suspend+resume (and hibernation) sequences
Now that the ftrace kernel thread is gone, we can allow tracing
during suspend/resume again.
So revert these two commits:
f42ac38c5 "ftrace: disable tracing for suspend to ram"
41108eb10 "ftrace: disable tracing for hibernation"
This should be tested very carefully, as it could interact with
altneratives instruction patching, etc.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
By using WARN(), kerneloops.org can collect which component is causing
the delay and make statistics about that. suspend_test_finish() is
currently the number 2 item but unless we can collect who's causing
it we're not going to be able to fix the hot topic ones..
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Insufficient dependency - we really want CONFIG_RTC_CLASS=y there.
That will give us CONFIG_RTC_LIB=y, so the old dependency can be
simply replaced.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* get rid of fake struct file/struct dentry in __blkdev_get()
* merge __blkdev_get() and do_open()
* get rid of flags argument of blkdev_get()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When a system is resumed after a suspend, it will also unfreeze frozen
cgroups.
This patchs modifies the resume sequence to skip the tasks which are part
of a frozen control group.
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Tested-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch implements a new freezer subsystem in the control groups
framework. It provides a way to stop and resume execution of all tasks in
a cgroup by writing in the cgroup filesystem.
The freezer subsystem in the container filesystem defines a file named
freezer.state. Writing "FROZEN" to the state file will freeze all tasks
in the cgroup. Subsequently writing "RUNNING" will unfreeze the tasks in
the cgroup. Reading will return the current state.
* Examples of usage :
# mkdir /containers/freezer
# mount -t cgroup -ofreezer freezer /containers
# mkdir /containers/0
# echo $some_pid > /containers/0/tasks
to get status of the freezer subsystem :
# cat /containers/0/freezer.state
RUNNING
to freeze all tasks in the container :
# echo FROZEN > /containers/0/freezer.state
# cat /containers/0/freezer.state
FREEZING
# cat /containers/0/freezer.state
FROZEN
to unfreeze all tasks in the container :
# echo RUNNING > /containers/0/freezer.state
# cat /containers/0/freezer.state
RUNNING
This is the basic mechanism which should do the right thing for user space
task in a simple scenario.
It's important to note that freezing can be incomplete. In that case we
return EBUSY. This means that some tasks in the cgroup are busy doing
something that prevents us from completely freezing the cgroup at this
time. After EBUSY, the cgroup will remain partially frozen -- reflected
by freezer.state reporting "FREEZING" when read. The state will remain
"FREEZING" until one of these things happens:
1) Userspace cancels the freezing operation by writing "RUNNING" to
the freezer.state file
2) Userspace retries the freezing operation by writing "FROZEN" to
the freezer.state file (writing "FREEZING" is not legal
and returns EIO)
3) The tasks that blocked the cgroup from entering the "FROZEN"
state disappear from the cgroup's set of tasks.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: export thaw_process]
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Tested-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the TIF_FREEZE flag is available in all architectures, extract
the refrigerator() and freeze_task() from kernel/power/process.c and make
it available to all.
The refrigerator() can now be used in a control group subsystem
implementing a control group freezer.
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Tested-by: Matt Helsley <matthltc@us.ibm.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We currently use a PM notifier to disable user mode helpers before suspend
and hibernation and to re-enable them during resume. However, this is not
an ideal solution, because if any drivers want to upload firmware into
memory before suspend, they have to use a PM notifier for this purpose and
there is no guarantee that the ordering of PM notifiers will be as
expected (ie. the notifier that disables user mode helpers has to be run
after the driver's notifier used for uploading the firmware).
For this reason, it seems better to move the disabling and enabling of
user mode helpers to separate functions that will be called by the PM core
as necessary.
[akpm@linux-foundation.org: remove unneeded ifdefs]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In accordance with commit f42ac38c59
("ftrace: disable tracing for suspend to ram"), disable tracing
around the suspend code in hibernation code paths.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I've been painstakingly debugging the issue with suspend to ram and
ftraced. The 2.6.28 code does not have this issue, but since the mcount
recording is not going to be in 27, this must be solved for the ftrace
daemon version.
The resume from suspend to ram would reboot because it was triple
faulting. Debugging further, I found that calling the mcount function
itself was not an issue, but it would fault when it incremented
preempt_count. preempt_count is on the tasks info structure that is on the
low memory address of the task's stack. For some reason, it could not
write to it. Resuming out of suspend to ram does quite a lot of funny
tricks to get to work, so it is not surprising at all that simply doing a
preempt_disable() would cause a fault.
Thanks to Rafael for suggesting to add a "while (1);" to find the place in
resuming that is causing the fault. I would place the loop somewhere in
the code, compile and reboot and see if it would either reboot (hit the
fault) or simply hang (hit the loop). Doing this over and over again, I
narrowed it down that it was happening in enable_nonboot_cpus.
At this point, I found that it is easier to simply disable tracing around
the suspend code, instead of searching for the particular function that
can not handle doing a preempt_disable.
This patch disables the tracer as it suspends and reenables it on resume.
I tested this patch on my Laptop, and it can resume fine with the patch.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch implements devices state save/restore before after kexec.
This patch together with features in kexec_jump patch can be used for
following:
- A simple hibernation implementation without ACPI support. You can kexec a
hibernating kernel, save the memory image of original system and shutdown
the system. When resuming, you restore the memory image of original system
via ordinary kexec load then jump back.
- Kernel/system debug through making system snapshot. You can make system
snapshot, jump back, do some thing and make another system snapshot.
- Cooperative multi-kernel/system. With kexec jump, you can switch between
several kernels/systems quickly without boot process except the first time.
This appears like swap a whole kernel/system out/in.
- A general method to call program in physical mode (paging turning
off). This can be used to invoke BIOS code under Linux.
The following user-space tools can be used with kexec jump:
- kexec-tools needs to be patched to support kexec jump. The patches
and the precompiled kexec can be download from the following URL:
source: http://khibernation.sourceforge.net/download/release_v10/kexec-tools/kexec-tools-src_git_kh10.tar.bz2
patches: http://khibernation.sourceforge.net/download/release_v10/kexec-tools/kexec-tools-patches_git_kh10.tar.bz2
binary: http://khibernation.sourceforge.net/download/release_v10/kexec-tools/kexec_git_kh10
- makedumpfile with patches are used as memory image saving tool, it
can exclude free pages from original kernel memory image file. The
patches and the precompiled makedumpfile can be download from the
following URL:
source: http://khibernation.sourceforge.net/download/release_v10/makedumpfile/makedumpfile-src_cvs_kh10.tar.bz2
patches: http://khibernation.sourceforge.net/download/release_v10/makedumpfile/makedumpfile-patches_cvs_kh10.tar.bz2
binary: http://khibernation.sourceforge.net/download/release_v10/makedumpfile/makedumpfile_cvs_kh10
- An initramfs image can be used as the root file system of kexeced
kernel. An initramfs image built with "BuildRoot" can be downloaded
from the following URL:
initramfs image: http://khibernation.sourceforge.net/download/release_v10/initramfs/rootfs_cvs_kh10.gz
All user space tools above are included in the initramfs image.
Usage example of simple hibernation:
1. Compile and install patched kernel with following options selected:
CONFIG_X86_32=y
CONFIG_RELOCATABLE=y
CONFIG_KEXEC=y
CONFIG_CRASH_DUMP=y
CONFIG_PM=y
CONFIG_HIBERNATION=y
CONFIG_KEXEC_JUMP=y
2. Build an initramfs image contains kexec-tool and makedumpfile, or
download the pre-built initramfs image, called rootfs.gz in
following text.
3. Prepare a partition to save memory image of original kernel, called
hibernating partition in following text.
4. Boot kernel compiled in step 1 (kernel A).
5. In the kernel A, load kernel compiled in step 1 (kernel B) with
/sbin/kexec. The shell command line can be as follow:
/sbin/kexec --load-preserve-context /boot/bzImage --mem-min=0x100000
--mem-max=0xffffff --initrd=rootfs.gz
6. Boot the kernel B with following shell command line:
/sbin/kexec -e
7. The kernel B will boot as normal kexec. In kernel B the memory
image of kernel A can be saved into hibernating partition as
follow:
jump_back_entry=`cat /proc/cmdline | tr ' ' '\n' | grep kexec_jump_back_entry | cut -d '='`
echo $jump_back_entry > kexec_jump_back_entry
cp /proc/vmcore dump.elf
Then you can shutdown the machine as normal.
8. Boot kernel compiled in step 1 (kernel C). Use the rootfs.gz as
root file system.
9. In kernel C, load the memory image of kernel A as follow:
/sbin/kexec -l --args-none --entry=`cat kexec_jump_back_entry` dump.elf
10. Jump back to the kernel A as follow:
/sbin/kexec -e
Then, kernel A is resumed.
Implementation point:
To support jumping between two kernels, before jumping to (executing)
the new kernel and jumping back to the original kernel, the devices
are put into quiescent state, and the state of devices and CPU is
saved. After jumping back from kexeced kernel and jumping to the new
kernel, the state of devices and CPU are restored accordingly. The
devices/CPU state save/restore code of software suspend is called to
implement corresponding function.
Known issues:
- Because the segment number supported by sys_kexec_load is limited,
hibernation image with many segments may not be load. This is
planned to be eliminated by adding a new flag to sys_kexec_load to
make a image can be loaded with multiple sys_kexec_load invoking.
Now, only the i386 architecture is supported.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cope with a quirk of some RTCs (notably ACPI ones) which aren't guaranteed
to implement oneshot behavior when they woke the system from sleeep:
forcibly disable the alarm, just in case.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix try_to_freeze_tasks()'s use of do_div() on an s64 by making
elapsed_csecs64 a u64 instead and dividing that.
Possibly this should be guarded lest the interval calculation turn up
negative, but the possible negativity of the result of the division is
cast away anyway.
This was introduced by patch 438e2ce68d.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
schedule sysrq poweroff on boot cpu.
sysrq poweroff needs to disable nonboot cpus, and we need to run this on boot
cpu to avoid any recursion. http://bugzilla.kernel.org/show_bug.cgi?id=10897
[kosaki.motohiro@jp.fujitsu.com: build fix]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Rus <harbour@sfinx.od.ua>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch simplifies the memory bitmap manipulations.
- remove the member size in struct bm_block
It is not necessary for struct bm_block to have the number of bit chunks that
can be calculated by using end_pfn and start_pfn.
- use find_next_bit() for memory_bm_next_pfn
No need to invent the bitmap library only for the memory bitmap.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Boot-time test for system suspend states (STR or standby). The generic
RTC framework triggers wakeup alarms, which are used to exit those states.
- Measures some aspects of suspend time ... this uses "jiffies" until
someone converts it to use a timebase that works properly even while
timer IRQs are disabled.
- Triggered by a command line parameter. By default nothing even
vaguely troublesome will happen, but "test_suspend=mem" will give
you a brief STR test during system boot. (Or you may need to use
"test_suspend=standby" instead, if your hardware needs that.)
This isn't without problems. It fires early enough during boot that for
example both PCMCIA and MMC stacks have misbehaved. The workaround in
those cases was to boot without such media cards inserted.
[matthltc@us.ibm.com: fix compile failure in boot time suspend selftest]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Pavel Machek <pavel@suse.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Xen save/restore needs bits of code enabled by PM_SLEEP, and PM_SLEEP
depends on PM. So make XEN_SAVE_RESTORE depend on PM and PM_SLEEP
depend on XEN_SAVE_RESTORE.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (72 commits)
Revert "x86/PCI: ACPI based PCI gap calculation"
PCI: remove unnecessary volatile in PCIe hotplug struct controller
x86/PCI: ACPI based PCI gap calculation
PCI: include linux/pm_wakeup.h for device_set_wakeup_capable
PCI PM: Fix pci_prepare_to_sleep
x86/PCI: Fix PCI config space for domains > 0
Fix acpi_pm_device_sleep_wake() by providing a stub for CONFIG_PM_SLEEP=n
PCI: Simplify PCI device PM code
PCI PM: Introduce pci_prepare_to_sleep and pci_back_from_sleep
PCI ACPI: Rework PCI handling of wake-up
ACPI: Introduce new device wakeup flag 'prepared'
ACPI: Introduce acpi_device_sleep_wake function
PCI: rework pci_set_power_state function to call platform first
PCI: Introduce platform_pci_power_manageable function
ACPI: Introduce acpi_bus_power_manageable function
PCI: make pci_name use dev_name
PCI: handle pci_name() being const
PCI: add stub for pci_set_consistent_dma_mask()
PCI: remove unused arch pcibios_update_resource() functions
PCI: fix pci_setup_device()'s sprinting into a const buffer
...
Fixed up conflicts in various files (arch/x86/kernel/setup_64.c,
arch/x86/pci/irq.c, arch/x86/pci/pci.h, drivers/acpi/sleep/main.c,
drivers/pci/pci.c, drivers/pci/pci.h, include/acpi/acpi_bus.h) from x86
and ACPI updates manually.
We can avoid taking the BKL in snapshot_ioctl() if pm_mutex is used to prevent
the ioctls from being executed concurrently.
In addition, although it is only possible to open /dev/snapshot once, the task
which has done that may spawn a child that will inherit the open descriptor,
so in theory they can call snapshot_write(), snapshot_read() and
snapshot_release() concurrently. pm_mutex can also be used for mutual
exclusion in such cases.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Push BKL down into ioctl handlers - snapshot device.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
The freezer currently attempts to distinguish kernel threads from
user space tasks by checking if their mm pointer is unset and it
does not send fake signals to kernel threads. However, there are
kernel threads, mostly related to networking, that behave like
user space tasks and may want to be sent a fake signal to be frozen.
Introduce the new process flag PF_FREEZER_NOSIG that will be set
by default for all kernel threads and make the freezer only send
fake signals to the tasks having PF_FREEZER_NOSIG unset. Provide
the set_freezable_with_signal() function to be called by the kernel
threads that want to be sent a fake signal for freezing.
This patch should not change the freezer's observable behavior.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit 6fbbec428c8e7bb617da2e8a589af2e97bcf3bc4.
Rafael doesnt like it - it breaks various assumptions.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Xen save/restore requires PM_SLEEP to be set without requiring
SUSPEND or HIBERNATION.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
ACPI PM: Add possibility to change suspend sequence
There are some systems out there that don't work correctly with
our current suspend/hibernation code ordering. Provide a workaround
for these systems allowing them to pass 'acpi_sleep=old_ordering' in
the kernel command line so that it will use the pre-ACPI 2.0 ("old")
suspend code ordering.
Unfortunately, this requires us to add a platform hook to the
resuming of devices for recovering the platform in case one of the
device drivers' .suspend() routines returns error code. Namely,
ACPI 1.0 specifies that _PTS should be called before suspending
devices, but _WAK still should be called before resuming them in
order to undo the changes made by _PTS. However, if there is an
error during suspending devices, they are automatically resumed
without returning control to the PM core, so the _WAK has to be
called from within device_resume() in that cases.
The patch also reorders and refactors the ACPI suspend/hibernation
code to avoid duplication as far as reasonably possible.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce 'struct pm_ops' and 'struct pm_ext_ops' ('ext' meaning
'extended') representing suspend and hibernation operations for bus
types, device classes, device types and device drivers.
Modify the PM core to use 'struct pm_ops' and 'struct pm_ext_ops'
objects, if defined, instead of the ->suspend(), ->resume(),
->suspend_late(), and ->resume_early() callbacks (the old callbacks
will be considered as legacy and gradually phased out).
The main purpose of doing this is to separate suspend (aka S2RAM and
standby) callbacks from hibernation callbacks in such a way that the
new callbacks won't take arguments and the semantics of each of them
will be clearly specified. This has been requested for multiple
times by many people, including Linus himself, and the reason is that
within the current scheme if ->resume() is called, for example, it's
difficult to say why it's been called (ie. is it a resume from RAM or
from hibernation or a suspend/hibernation failure etc.?).
The second purpose is to make the suspend/hibernation callbacks more
flexible so that device drivers can handle more than they can within
the current scheme. For example, some drivers may need to prevent
new children of the device from being registered before their
->suspend() callbacks are executed or they may want to carry out some
operations requiring the availability of some other devices, not
directly bound via the parent-child relationship, in order to prepare
for the execution of ->suspend(), etc.
Ultimately, we'd like to stop using the freezing of tasks for suspend
and therefore the drivers' suspend/hibernation code will have to take
care of the handling of the user space during suspend/hibernation.
That, in turn, would be difficult within the current scheme, without
the new ->prepare() and ->complete() callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Prior to suspend, we allocate and switch to a new VT; after suspend, we switch
back to the original VT. This can be slow, and is completely unnecessary if
the framebuffer we're using can restore video properly.
This adds a hook that allows drivers to select whether or not to do this vt
switch, and changes the gxfb driver to call this hook. It also adds a module
param to gxfb to allow controlling of the vt switch (defaulting to no switch).
(Note: I'm not convinced that console_sem is the best way to protect this, but
we should probably have some form of locking..)
[akpm@linux-foundation.org: build fix]
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
AFAICT pm_send_all is a nop when noone uses pm_register...
Hmm.. can we just force CONFIG_PM_LEGACY=n, and see what happens?
Or maybe this is better idea? It may break build somewhere, but it
should be easy to fix... (it builds here, i386 and x86-64).
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Move 00-INDEX entries to power/00-INDEX (and add entry for
pm_qos_interface.txt).
Update references to moved filenames.
Fix some trailing whitespace.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There is a problem in the hibernation code that triggers on some NUMA
systems on which pfn_valid() returns 'true' for some PFNs that don't
belong to any zone. Namely, there is a BUG_ON() in
memory_bm_find_bit() that triggers for PFNs not belonging to any
zone and passing the pfn_valid() test. On the affected systems it
triggers when we mark PFNs reported by the platform as not saveable,
because the PFNs in question belong to a region mapped directly using
iorepam() (i.e. the ACPI data area) and they pass the pfn_valid()
test.
Modify memory_bm_find_bit() so that it returns an error if given PFN
doesn't belong to any zone instead of crashing the kernel and ignore
the result returned by it in mark_nosave_pages(), while marking the
"nosave" memory regions.
This doesn't affect the hibernation functionality, as we won't touch
the PFNs in question anyway.
http://bugzilla.kernel.org/show_bug.cgi?id=9966 .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This changes the "freezer" code used by suspend/hibernate in its treatment
of tasks in TASK_STOPPED (job control stop) and TASK_TRACED (ptrace) states.
As I understand it, the intent of the "freezer" is to hold all tasks
from doing anything significant. For this purpose, TASK_STOPPED and
TASK_TRACED are "frozen enough". It's possible the tasks might resume
from ptrace calls (if the tracer were unfrozen) or from signals
(including ones that could come via timer interrupts, etc). But this
doesn't matter as long as they quickly block again while "freezing" is
in effect. Some minor adjustments to the signal.c code make sure that
try_to_freeze() very shortly follows all wakeups from both kinds of
stop. This lets the freezer code safely leave stopped tasks unmolested.
Changing this fixes the longstanding bug of seeing after resuming from
suspend/hibernate your shell report "[1] Stopped" and the like for all
your jobs stopped by ^Z et al, as if you had freshly fg'd and ^Z'd them.
It also removes from the freezer the arcane special case treatment for
ptrace'd tasks, which relied on intimate knowledge of ptrace internals.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the last step of hibernation in the "platform" mode (with the
help of ACPI) we use the suspend code, including the devices'
->suspend() methods, to prepare the system for entering the ACPI S4
system sleep state.
But at least for some devices the operations performed by the
->suspend() callback in that case must be different from its operations
during regular suspend.
For this reason, introduce the new PM event type PM_EVENT_HIBERNATE and
pass it to the device drivers' ->suspend() methods during the last phase
of hibernation, so that they can distinguish this case and handle it as
appropriate. Modify the drivers that handle PM_EVENT_SUSPEND in a
special way and need to handle PM_EVENT_HIBERNATE in the same way.
These changes are necessary to fix a hibernation regression related
to the i915 driver (ref. http://lkml.org/lkml/2008/2/22/488).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make hibernation work with CONFIG_DEBUG_PAGEALLOC set on x86, by
checking if the pages to be copied are marked as present in the
kernel mapping and temporarily marking them as present if that's not
the case. No functional modifications are introduced if
CONFIG_DEBUG_PAGEALLOC is unset.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
resume_file[] and create_image() can become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Add comments explaing how drain_pages() works.
- Eliminate useless functions
- Rename drain_all_local_pages to drain_all_pages(). It does drain
all pages not only those of the local processor.
- Eliminate useless interrupt off / on sequences. drain_pages()
disables interrupts on its own. The execution thread is
pinned to processor by the caller. So there is no need to
disable interrupts.
- Put drain_all_pages() declaration in gfp.h and remove the
declarations from suspend.h and from mm/memory_hotplug.c
- Make software suspend call drain_all_pages(). The draining
of processor local pages is may not the right approach if
software suspend wants to support SMP. If they call drain_all_pages
then we can make drain_pages() static.
[akpm@linux-foundation.org: fix build]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Following the recent change in the suspend code path, switch consoles before
calling PM notifiers during hibernation.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
In order to fix APM emulation it is necessary to enable apm-emulation
notifications for suspends triggered in various ways via the suspend
notifiers. However, this will cause the systems using APM emulation
to lock up between X being needed to switch away from the VT and X
already waiting for resume in the APM ioctl.
This patch moves the console switch (if enabled) before the suspend
notification (and after the resume notification) to avoid this issue.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch makes the freezer optional for suspend to allow the
system to work (or not work) like the original PMU suspend.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce global hibernation callback .end() and rename global
hibernation callback .start() to .begin(), in analogy with the
recent modifications of the global suspend callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
On ACPI systems the target state set by acpi_pm_set_target() is
reset by acpi_pm_finish(), but that need not be called if the
suspend fails. All platforms that use the .set_target() global
suspend callback are affected by analogous issues.
For this reason, we need an additional global suspend callback that
will reset the target state regardless of whether or not the suspend
is successful. Also, it is reasonable to rename the .set_target()
callback, since it will be used for a different purpose on ACPI
systems (due to ACPI 1.0x code ordering requirements).
Introduce the global suspend callback .end() to be executed at the
end of the suspend sequence and rename the .set_target() global
suspend callback to .begin().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
kernel/power/main.c:488: error: ‘pm_test_attr’ undeclared here (not in a function)
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This cleans up the suspend Kconfig and removes the need to
declare centrally which architectures support suspend. All
architectures that currently support suspend are modified
accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This cleans up the hibernation Kconfig and removes the need to
declare centrally which architectures support hibernation. All
architectures that currently support hibernation are modified
accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Make hibernation messages start with one common prefix "PM: " and use
the word "hibernation" in the messages as a synonym of "suspend to
disk".
Turn some KERN_INFO messages into debug ones.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Make suspend messages start with one common prefix "PM: ".
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove the unnecessary extern declaration of resume_file[]
from kernel/power/swap.c .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix a comment in kernel/power/disk.c so that it doesn't contain lines
longer that 80 characters.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix a comment in kernel/power/main.c so that it doesn't contain lines
longer that 80 characters.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Move the low level restore code to kernel/power/disk.c , since the
corresponding low level hibernation code is already there.
Make restore fail if device_power_down(PMSG_PRETHAW) returns an
error.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Suspend: Make debug facility depend on CONFIG_SUSPEND
Make the new suspend debug facility code depend on CONFIG_SUSPEND,
as appropriate, to remove the compiler warning printed when CONFIG_PM is set
and CONFIG_SUSPEND is not set.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch (as1008b) converts the PM notifier routines from inline
calls to out-of-line code. It also prevents pm_chain_head from
being created when CONFIG_PM_SLEEP isn't enabled, and EXPORTs the
notifier registration and unregistration routines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
When trying to debug a suspend failure I started implementing
PM_TRACE for powerpc. I then noticed that I'm debugging a suspend
failure and so PM_TRACE isn't useful at all, but thought that
nonetheless this could be useful in the future.
Basically, to support PM_TRACE, you add a Kconfig option that
selects PM_TRACE and provides the infrastructure as per the
help text of PM_TRACE.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Make it possible to test the hibernation core code with the help of the
/sys/power/pm_test attribute introduced for suspend testing in the previous
patch.
Writing an appropriate string to this file causes the hibernation code to work
in one of the test modes defined as follows:
freezer
- test the freezing of processes
devices
- test the freezing of processes and suspending of devices
platform
- test the freezing of processes, suspending of devices and platform global
control methods(*)
processors
- test the freezing of processes, suspending of devices, platform global
control methods(*) and the disabling of nonboot CPUs
core
- test the freezing of processes, suspending of devices, platform global
control methods(*), the disabling of nonboot CPUs and suspending of
platform/system devices
(*) - the platform global control methods are only available on ACPI systems
and are only tested if the hibernation mode is set to "platform"
Then, if a hibernation is started by normal means, the hibernation core will
perform its normal operations up to the point indicated by given test level.
Next, it will wait for 5 seconds and carry out the resume operations needed to
transition the system back to the fully functional state.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce sysfs attribute /sys/power/pm_test allowing one to test the suspend
core code. Namely, writing one of the strings:
freezer
devices
platform
processors
core
to this file causes the suspend code to work in one of the test modes defined as
follows:
freezer
- test the freezing of processes
devices
- test the freezing of processes and suspending of devices
platform
- test the freezing of processes, suspending of devices and platform global
control methods(*)
processors
- test the freezing of processes, suspending of devices, platform global
control methods and the disabling of nonboot CPUs
core
- test the freezing of processes, suspending of devices, platform global
control methods, the disabling of nonboot CPUs and suspending of
platform/system devices
(*) These are ACPI global control methods on ACPI systems
Then, if a suspend is started by normal means, the suspend core will perform
its normal operations up to the point indicated by given test level. Next, it
will wait for 5 seconds and carry out the resume operations needed to transition
the system back to the fully functional state.
Writing "none" to /sys/power/pm_test turns the testing off.
When open for reading, /sys/power/pm_test contains a space-separated list of all
available tests (including "none" that represents the normal functionality) in
which the current test level is indicated by square brackets.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Add PM_RESTORE_PREPARE and PM_POST_RESTORE notifiers to the PM core, to be used
in analogy with the existing PM_HIBERNATION_PREPARE and PM_POST_HIBERNATION
notifiers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch moves the prototypes of count_highmem_pages() and
restore_highmem() to kernel/power/power.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Move the definitions of hibernation ioctls to a separate header file in
include/linux, which can be exported to the user space.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Three ioctl numbers belonging to the hibernation userland interface,
SNAPSHOT_ATOMIC_SNAPSHOT, SNAPSHOT_AVAIL_SWAP, SNAPSHOT_GET_SWAP_PAGE,
are defined in a wrong way (eg. not portable). Provide new ioctl numbers for
these ioctls and mark the existing ones as deprecated.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Mark the SNAPSHOT_SET_SWAP_FILE ioctl belonging to the hibernation userland
interface as deprecated.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Modify the hibernation userland interface by adding two new ioctls to it,
SNAPSHOT_PLATFORM_SUPPORT and SNAPSHOT_POWER_OFF, that can be used,
respectively, to switch the hibernation platform support on/off and to make the
kernel transition the system to the hibernation state (eg. ACPI S4) using the
platform (eg. ACPI) driver.
These ioctls are intended to replace the misdesigned SNAPSHOT_PMOPS ioctl,
which from now is regarded as obsolete and will be removed in the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a new ioctl, SNAPSHOT_GET_IMAGE_SIZE, returning the size of the (just
created) hibernation image, to the hibernation userland interface.
This ioctl is necessary so that the userland utilities using the interface need
not access the hibernation image header, owned by the kernel, in order to obtain
the size of the image.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'task_killable' of git://git.kernel.org/pub/scm/linux/kernel/git/willy/misc: (22 commits)
Remove commented-out code copied from NFS
NFS: Switch from intr mount option to TASK_KILLABLE
Add wait_for_completion_killable
Add wait_event_killable
Add schedule_timeout_killable
Use mutex_lock_killable in vfs_readdir
Add mutex_lock_killable
Use lock_page_killable
Add lock_page_killable
Add fatal_signal_pending
Add TASK_WAKEKILL
exit: Use task_is_*
signal: Use task_is_*
sched: Use task_contributes_to_load, TASK_ALL and TASK_NORMAL
ptrace: Use task_is_*
power: Use task_is_*
wait: Use TASK_NORMAL
proc/base.c: Use task_is_*
proc/array.c: Use TASK_REPORT
perfmon: Use task_is_*
...
Fixed up conflicts in NFS/sunrpc manually..
/sys/power should not be a kset, that's overkill. This patch renames it
to power_kset and fixes up all usages of it in the tree.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Switch all dynamically created ksets, that export simple attributes,
to kobj_attribute from subsys_attribute. Struct subsys_attribute will
be removed.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mike Halcrow <mhalcrow@us.ibm.com>
Cc: Phillip Hellewell <phillip@hellewell.homeip.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dynamically create the kset instead of declaring it statically. We also
rename power_subsys to power_kset to catch all users of the variable and
we properly export it so that people don't have to guess that it really
is present in the system.
The pseries code is wierd, why is it createing /sys/power if CONFIG_PM
is disabled? Oh well, stupid big boxes ignoring config options...
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need a "default" ktype for a kset. We should set this
explicitly every time for each kset. This change is needed so that we
can make ksets dynamic, and cleans up one of the odd, undocumented
assumption that the kset/kobject/ktype model has.
This patch is based on a lot of help from Kay Sievers.
Nasty bug in the block code was found by Dave Young
<hidave.darkstar@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ACPI and APM used "pm_active" to guarantee that
they would not be simultaneously active.
But pm_active was recently moved under CONFIG_PM_LEGACY,
so that without CONFIG_PM_LEGACY, pm_active became a NOP --
allowing ACPI and APM to both be simultaneously enabled.
This caused unpredictable results, including boot hangs.
Further, the code under CONFIG_PM_LEGACY is scheduled
for removal.
So replace pm_active with pm_flags.
pm_flags depends only on CONFIG_PM,
which is present for both CONFIG_APM and CONFIG_ACPI.
http://bugzilla.kernel.org/show_bug.cgi?id=9194
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Lockdep reports a circular locking dependency in the hibernate code
because
- during system boot hibernate code (from an initcall) locks pm_mutex
and then a sysfs buffer mutex via name_to_dev_t
- during regular operation hibernate code locks pm_mutex under a
sysfs buffer mutex because it's called from sysfs methods.
The deadlock can never happen because during initcall invocation nothing
can write to sysfs yet. This removes the lockdep report by marking the
initcall locking as being in a different class.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the loop style of copy_data_pages() to remove a duplicate condition.
Signed-off-by: Fengguang Wu <wfg@mail.ustc.edu.cn>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Make hibernation_platform_enter() execute the enter-a-sleep-state sequence
instead of the mixed shutdown-with-entering-S4 thing.
Replace the shutting down of devices done by kernel_shutdown_prepare(), before
entering the ACPI S4 sleep state, with suspending them and the shutting down
of sysdevs with calling device_power_down(PMSG_SUSPEND) (just like before
entering S1 or S3, but the target state is now S4). Also, disable the
nonboot CPUs before entering the sleep state (S4), which generally always is a
good idea.
This is known to fix the "double disk spin down during hibernation" on some
machines, eg. HPC nx6325 (ref. http://lkml.org/lkml/2007/8/7/316 and the
following thread). Moreover, it has been reported to make
/sys/class/rtc/rtc0/wakealarm work correctly with hibernation for some users.
It also generally causes the hibernation state (ACPI S4) to be entered faster.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following scenario leads to total confusion of the platform firmware on
some boxes (eg. HPC nx6325):
* Hibernate with ACPI enabled
* Resume passing "acpi=off" to the boot kernel
To prevent this from happening it's necessary to check if ACPI is enabled (and
enable it if that's not the case) _right_ _after_ control has been transfered
from the boot kernel to the image kernel, before device_power_up() is called
(ie. with interrupts disabled). Enabling ACPI after calling
device_power_up() turns out to be insufficient.
For this reason, introduce new hibernation callback ->leave() that will be
executed before device_power_up() by the restored image kernel. To make it
work, it also is necessary to move swsusp_suspend() from swsusp.c to disk.c
(it's name is changed to "create_image", which is more up to the point).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the bits needed for supporting arbitrary boot kernels to the common
hibernation code.
To support arbitrary boot kernels, make it possible to replace the 'struct
new_utsname' and the kernel version in the hibernation image header by some
architecture specific data that will be used to verify if the image is valid
and to restore the image.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, there's a CONFIG_DISABLE_CONSOLE_SUSPEND that allows one to stop
the serial console from being suspended when the rest of the machine goes
to sleep. This is incredibly useful for debugging power management-related
things; however, having it as a compile-time option has proved to be
incredibly inconvenient for us (OLPC). There are plenty of times that we
want serial console to not suspend, but for the most part we'd like serial
console to be suspended.
This drops CONFIG_DISABLE_CONSOLE_SUSPEND, and replaces it with a kernel
boot parameter (no_console_suspend). By default, the serial console will
be suspended along with the rest of the system; by passing
'no_console_suspend' to the kernel during boot, serial console will remain
alive during suspend.
For now, this is pretty serial console specific; further fixes could be
applied to make this work for things like netconsole.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@suspend2.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Measure the time of the freezing of tasks, even if it doesn't fail.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Increase the freezer's verbosity a bit, so that it's easier to read problem
reports related to it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The freezer should not send signals to kernel threads, since that may lead to
subtle problems. In particular, commit
b74d0deb96 has changed recalc_sigpending_tsk()
so that it doesn't clear TIF_SIGPENDING. For this reason, if the freezer
continues to send fake signals to kernel threads and the freezing of kernel
threads fails, some of them may be running with TIF_SIGPENDING set forever.
Accordingly, recalc_sigpending_tsk() shouldn't set the task's TIF_SIGPENDING
flag if TIF_FREEZE is set.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The syncing of filesystems from within the freezer is generally not needed.
Also, if there's an ext3 filesystem loopback-mounted from a FUSE one, the
syncing results in writes to it and deadlocks. Similarly, it will deadlock if
FUSE implements sync.
Change freeze_processes() so that it doesn't execute sys_sync() and make the
suspend and hibernation code path sync filesystems independently of the
freezer.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename 'struct hibernation_ops' to 'struct platform_hibernation_ops' in
analogy with 'struct platform_suspend_ops'.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During hibernation we also need to tell the ACPI core that we're going to put
the system into the S4 sleep state. For this reason, an additional method in
'struct hibernation_ops' is needed, playing the role of set_target() in
'struct platform_suspend_operations'. Moreover, the role of the .prepare()
method is now different, so it's better to introduce another method, that in
general may be different from .prepare(), that will be used to prepare the
platform for creating the hibernation image (.prepare() is used anyway to
notify the platform that we're going to enter the low power state after the
image has been saved).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The variable suspend_ops representing the set of global platform-specific
suspend-related operations, used by the PM core, need not be exported outside
of kernel/power/main.c . Make it static.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no reason why the .prepare() and .finish() methods in 'struct
platform_suspend_ops' should take any arguments, since architectures don't use
these methods' argument in any practically meaningful way (ie. either the
target system sleep state is conveyed to the platform by .set_target(), or
there is only one suspend state supported and it is indicated to the PM core
by .valid(), or .prepare() and .finish() aren't defined at all). There also
is no reason why .finish() should return any result.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The name of 'struct pm_ops' suggests that it is related to the power
management in general, but in fact it is only related to suspend. Moreover,
its name should indicate what this structure is used for, so it seems
reasonable to change it to 'struct platform_suspend_ops'. In that case, the
name of the global variable of this type used by the PM core and the names of
related functions should be changed accordingly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
suspend_enter() can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dependencies of CONFIG_SUSPEND and CONFIG_HIBERNATION introduced by commit
296699de6b "Introduce CONFIG_SUSPEND for
suspend-to-Ram and standby" are incorrect, as they don't cover the facts that
(1) not all architectures support suspend and (2) SMP hibernation is only
possible on X86 and PPC64 (if CONFIG_PPC64_SWSUSP is set).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some systems some PFNs reported by the early initialization code as
'nosave' may be invalid. If we try to set the corresponding bits in the
hibernation bitmap, BUG_ON() in memory_bm_find_bit() will be triggered and
the system won't be able to boot (cf.
https://bugzilla.novell.com/show_bug.cgi?id=296242).
Prevent this from happening by verifying if the 'nosave' PFNs are valid in
mark_nosave_pages().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce CONFIG_SUSPEND representing the ability to enter system sleep
states, such as the ACPI S3 state, and allow the user to choose SUSPEND
and HIBERNATION independently of each other.
Make HOTPLUG_CPU be selected automatically if SUSPEND or HIBERNATION has
been chosen and the kernel is intended for SMP systems.
Also, introduce CONFIG_PM_SLEEP which is automatically selected if
CONFIG_SUSPEND or CONFIG_HIBERNATION is set and use it to select the
code needed for both suspend and hibernation.
The top-level power management headers and the ACPI code related to
suspend and hibernation are modified to use the new definitions (the
changes in drivers/acpi/sleep/main.c are, mostly, moving code to reduce
the number of ifdefs).
There are many other files in which CONFIG_PM can be replaced with
CONFIG_PM_SLEEP or even with CONFIG_SUSPEND, but they can be updated in
the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace CONFIG_SOFTWARE_SUSPEND with CONFIG_HIBERNATION to avoid
confusion (among other things, with CONFIG_SUSPEND introduced in the
next patch).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit bd804eba1c ("PM: Introduce
pm_power_off_prepare") caused problems in the poweroff path, as reported by
YOSHIFUJI Hideaki / 吉藤英明.
Generally, sysdev_shutdown() should be called after the ACPI preparation for
powering the system off. To make it happen, we can separate sysdev_shutdown()
from device_shutdown() and call it directly wherever necessary.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: YOSHIFUJI Hideaki / 吉藤英明 <yoshfuji@linux-ipv6.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move "debug during resume from s2ram" into the variable we already use
for real-mode flags to simplify code. It also closes nasty trap for
the user in acpi_sleep_setup; order of parameters actually mattered there,
acpi_sleep=s3_bios,s3_mode doing something different from
acpi_sleep=s3_mode,s3_bios.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a feature allowing the user to make the system beep during a resume from
suspend to RAM, on x86_64 and i386.
This is useful for the users with broken resume from RAM, so that they can
verify if the control reaches the kernel after a wake-up event.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SNAPSHOT_S2RAM ioctl code is outdated and it should not duplicate the
suspend code in kernel/power/main.c. Fix that.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make it possible to register hibernation and suspend notifiers, so that
subsystems can perform hibernation-related or suspend-related operations that
should not be carried out by device drivers' .suspend() and .resume()
routines.
[akpm@linux-foundation.org: build fixes]
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We don't need to check if todo is positive before calling time_after() in
try_to_freeze_tasks(), because if todo is zero at this point, the loop will be
broken anyway due to the while () condition being false.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make try_to_freeze_tasks() and freeze_processes() return -EBUSY on failure
instead of the number of unfrozen tasks (none of the callers actually uses
this number).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use __set_current_state() as appropriate in refrigerator() instead of
accessing current->state directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kernel threads should not have TIF_FREEZE set when user space processes are
being frozen, since otherwise some of them might be frozen prematurely.
To prevent this from happening we can (1) make exit_mm() unset TIF_FREEZE
unconditionally just after clearing tsk->mm and (2) make try_to_freeze_tasks()
check if p->mm is different from zero and PF_BORROWED_MM is unset in p->flags
when user space processes are to be frozen.
Namely, when user space processes are being frozen, we only should set
TIF_FREEZE for tasks that have p->mm different from NULL and don't have
PF_BORROWED_MM set in p->flags. For this reason task_lock() must be used to
prevent try_to_freeze_tasks() from racing with use_mm()/unuse_mm(), in which
p->mm and p->flags.PF_BORROWED_MM are changed under task_lock(p). Also, we
need to prevent the following scenario from happening:
* daemonize() is called by a task spawned from a user space code path
* freezer checks if the task has p->mm set and the result is positive
* task enters exit_mm() and clears its TIF_FREEZE
* freezer sets TIF_FREEZE for the task
* task calls try_to_freeze() and goes to the refrigerator, which is wrong at
that point
This requires us to acquire task_lock(p) before p->flags.PF_BORROWED_MM and
p->mm are examined and release it after TIF_FREEZE is set for p (or it turns
out that TIF_FREEZE should not be set).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During hibernation we call hibernation_ops->prepare() before creating the image,
but then, before saving it, we cancel the power transition by calling
hibernation_ops->finish(). Thus prior to calling hibernation_ops->enter() we
should let the platform firmware know that we're going to enter the low power
state after all.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the code ordering so that hibernation_ops->prepare() is called after
device_suspend(). This is needed so that we don't violate the ACPI
specification, which states that the _PTS and _GTS system-control methods,
executed from acpi_sleep_prepare(), ought to be called after devices have been
put in low power states.
The "Finish" label in hibernation_restore() is moved, because device_suspend()
resumes devices if the suspending of them fails and the restore code ordering
should reflect the hibernation code ordering.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At least on some machines it is necessary to prepare the ACPI firmware for the
restoration of the system memory state from the hibernation image if the
"platform" mode of hibernation has been used. Namely, in that cases we need
to disable the GPEs before replacing the "boot" kernel with the "frozen"
kernel (cf. http://bugzilla.kernel.org/show_bug.cgi?id=7887). After the
restore they will be re-enabled by hibernation_ops->finish(), but if the
restore fails, they have to be re-enabled by the restore code explicitly.
For this purpose we can introduce two additional hibernation operations,
called pre_restore() and restore_cleanup() and call them from the restore code
path. Still, they should be called if the "platform" mode of hibernation has
been used, so we need to pass the information about the hibernation mode from
the "frozen" kernel to the "boot" kernel in the image header.
Apparently, we can't drop the disabling of GPEs before the restore because of
Bug #7887 . We also can't do it unconditionally, because the GPEs wouldn't
have been enabled after a successful restore if the suspend had been done in
the 'shutdown' or 'reboot' mode.
In principle we could (and probably should) unconditionally disable the GPEs
before each snapshot creation *and* before the restore, but then we'd have to
unconditionally enable them after the snapshot creation as well as after the
restore (or restore failure) Still, for this purpose we'd need to modify
acpi_enter_sleep_state_prep() and acpi_leave_sleep_state() and we'd have to
introduce some mechanism synchronizing the disablind/enabling of the GPEs with
the device drivers' .suspend()/.resume() routines and with
disable_/enable_nonboot_cpus(). However, this would have affected the
suspend (ie. s2ram) code as well as the hibernation, which I'd like to avoid
in this patch series.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, much of the code in kernel/power/disk.c is duplicated in
kernel/power/user.c , mainly for historical reasons. By eliminating this code
duplication we can reduce the size of user.c quite substantially and remove
the maintenance difficulty resulting from it.
[bunk@stusta.de: kernel/power/disk.c: make code static]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the face of the recent change of suspend code ordering (cf.
http://marc.info/?l=linux-acpi&m=117938245931603&w=2) we should also modify
the code ordering in swsusp so that hibernation_ops->prepare() is executed
after device_suspend().
However, for this purpose it seems reasonable to eliminate the code
duplication between kernel/power/disk.c and kernel/power/user.c first. By
eliminating it we can reduce the size of user.c quite substantially and remove
the maintenance difficulty with making essentially the same changes in two
different places.
Moreover, we should also remove the calls to "platform" functions from the
restore code path, since it doesn't carry out any power transition of the
system, but we generally need to disable the GPEs before the restore if the
'platform' hibernation mode has been used. To do this, we can introduce two
new hibernation_ops to be used in the restore code.
This patch:
Make the code hibernation code in kernel/power/user.c be functionally
equivalent to the corresponding code in kernel/power/disk.c , as it should be.
The calls to the platform functions removed by this patch are incorrect. They
should be replaced with some other "platform" invocations that will be
introduced in one of the subsequent patches.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to enable things like PM_TRACE, you're required to enable
PM_DEBUG, which sends a large spew of messages on boot, and often times can
overflow dmesg buffer.
Create new PM_VERBOSE and shift that to be the option that enables
drivers/base/power's messages.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To see which tasks are stuck where.
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 52ade9b3b9 changed the suspend code
ordering to execute pm_ops->prepare() after the device model per-device
.suspend() calls in order to fix some ACPI-related issues. Unfortunately, it
broke the at91 platform which assumed that pm_ops->prepare() would be called
before suspending devices.
at91 used pm_ops->prepare() to get notified of the target system sleep state,
so that it could use this information while suspending devices. However, with
the current suspend code ordering pm_ops->prepare() is called too late for
this purpose. Thus, at91 needs an additional method in 'struct pm_ops' that
will be used for notifying the platform of the target system sleep state.
Moreover, in the future such a method will also be needed by ACPI.
This patch adds the .set_target() method to 'struct pm_ops' and makes the
suspend code call it, if implemented, before executing the device model
per-device .suspend() calls. It also modifies the at91 code to use
pm_ops->set_target() instead of pm_ops->prepare().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix oops caused by 'cat /dev/snapshot', reported by Arkadiusz Miskiewicz,
and make it impossible to thaw tasks with the help of the swsusp userland
interface while there is a snapshot image ready to save.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix sizeof(PAGE_SIZE) typo. It should be just PAGE_SIZE for zeroing the
swsusp_header.
Signed-off-by: OGAWA Hirofumi <hogawa@miraclelinux.com>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Steve Hawkes discovered a problem where recalc_sigpending_tsk was called in
do_sigaction but no signal_wake_up call was made, preventing later signals
from waking up blocked threads with TIF_SIGPENDING already set.
In fact, the few other calls to recalc_sigpending_tsk outside the signals
code are also subject to this problem in other race conditions.
This change makes recalc_sigpending_tsk private to the signals code. It
changes the outside calls, as well as do_sigaction, to use the new
recalc_sigpending_and_wake instead.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: <Steve.Hawkes@motorola.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Other than refrigerator, no one else calls frozen_process(). So move it from
include/linux/freezer.h to kernel/power/process.c.
Also, since a task can be marked as frozen by itself, we don't need to pass
the (struct task_struct *p) parameter to frozen_process().
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kernel threads can become userland processes by calling kernel_execve().
In particular, this may happen right after the try_to_freeze_tasks()
called with FREEZER_USER_SPACE has returned, so try_to_freeze_tasks()
needs to take userspace processes into consideration even if it is
called with FREEZER_KERNEL_THREADS.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently try_to_freeze_tasks() has to wait until all of the vforked processes
exit and for this reason every user can make it fail. To fix this problem we
can introduce the additional process flag PF_FREEZER_SKIP to be used by tasks
that do not want to be counted as freezable by the freezer and want to have
TIF_FREEZE set nevertheless. Then, this flag can be set by tasks using
sys_vfork() before they call wait_for_completion(&vfork) and cleared after
they have woken up. After clearing it, the tasks should call try_to_freeze()
as soon as possible.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the freezing of tasks fails and a task is preempted in refrigerator()
before calling frozen_process(), then thaw_tasks() may run before this task is
frozen. In that case the task will freeze and no one will thaw it.
To fix this race we can call freezing(current) in refrigerator() along with
frozen_process(current) under the task_lock() which also should be taken in
the error path of try_to_freeze_tasks() as well as in thaw_process().
Moreover, if thaw_process() additionally clears TIF_FREEZE for tasks that are
not frozen, we can be sure that all tasks are thawed and there are no pending
"freeze" requests after thaw_tasks() has run.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sysfs files /sys/power/disk and /sys/power/state do not work as
documented, since they allow the user to write only a few initial
characters of the input string to trigger the option (eg. 'echo pl >
/sys/power/disk' activates the platform mode of hibernation). Fix it.
Special thanks to Peter Moulder <Peter.Moulder@infotech.monash.edu.au> for
pointing out the problem.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit e3c7db621b we fixed the resume
ordering, so that the ACPI low-level resume code was called before the
actual driver resume was called. However, that broke the nesting logic
of suspend and resume, and we continued to suspend the devices _after_
we the ACPI device suspend code was called.
That resulted in us saving PCI state for devices that had already been
changed by ACPI, and in some cases disabled entirely (causing the PCI
save_state to be all-ones). Which in turn caused the wrong state to be
written back on resume.
This moves the ACPI device suspend to after the device model per-device
suspend() calls. This fixes the bogus state save.
Thanks to Lukáš Hejtmánek for testing.
Acked-by: Lukas Hejtmanek <xhejtman@ics.muni.cz>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Further fixes for the removal of 4level-fixup hack from ppc32
[POWERPC] EEH: log all PCI-X and PCI-E AER registers
[POWERPC] EEH: capture and log pci state on error
[POWERPC] EEH: Split up long error msg
[POWERPC] EEH: log error only after driver notification.
[POWERPC] fsl_soc: Make mac_addr const in fs_enet_of_init().
[POWERPC] Don't use SLAB/SLUB for PTE pages
[POWERPC] Spufs support for 64K LS mappings on 4K kernels
[POWERPC] Add ability to 4K kernel to hash in 64K pages
[POWERPC] Introduce address space "slices"
[POWERPC] Small fixes & cleanups in segment page size demotion
[POWERPC] iSeries: Make HVC_ISERIES the default
[POWERPC] iSeries: suppress build warning in lparmap.c
[POWERPC] Mark pages that don't exist as nosave
[POWERPC] swsusp: Introduce register_nosave_region_late
[ With Johannes Berg <johannes@sipsolutions.net> ]
Separate the hibernation (aka suspend to disk code) from the other suspend
code. In particular:
* Remove the definitions related to hibernation from include/linux/pm.h
* Introduce struct hibernation_ops and a new hibernate() function to hibernate
the system, defined in include/linux/suspend.h
* Separate suspend code in kernel/power/main.c from hibernation-related code
in kernel/power/disk.c and kernel/power/user.c (with the help of
hibernation_ops)
* Switch ACPI (the only user of pm_ops.pm_disk_mode) to hibernation_ops
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch introduces a new register_nosave_region_late function that
can be called from initcalls when register_nosave_region can no longer
be used because it uses bootmem.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Except for BUG_ON() checks, we should not use EXIT_XXXX defines outside of
exit/wait paths.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the definition of PAGES_FOR_IO to kernel/power/power.h and introduce
SPARE_PAGES representing the number of pages that should be freed by the
swsusp's memory shrinker in addition to PAGES_FOR_IO so that device drivers
can allocate some memory (up to 1 MB total) in their .suspend() routines
without causing the suspend to fail.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the leftover enable_nonboot_cpus() from snapshot_release().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clarify that "software suspend" is what's called "hibernation" in most user
interfaces, shrinking a terminology gap. (Examples include Gnome and
MS-Windows.)
Also provide a more succinct description of what it does, so you won't have
to read the whole novel in Kconfig; and highlights just why the lack of
BIOS requirements for swsusp are a big deal.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change /sys/power/disk to display all valid modes as well as the currently
selected one in a fashion known from the LED subsystem.
This changes userspace API, but it is apparently not used much (we asked
some userspace developers)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove software_suspend() and all its users since
pm_suspend(PM_SUSPEND_DISK) should be equivalent and there's no point in
having two interfaces for the same thing.
The patch also changes the valid_state function to return 0 (false) for
PM_SUSPEND_DISK when SOFTWARE_SUSPEND is not configured instead of
accepting it and having the whole thing fail later.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make swsusp use extents instead of a bitmap to trace swap pages allocated
for saving the image (the tracking is only needed in case there's an error,
so that the allocated swap pages can be released).
This should allow us to reduce the memory usage, practically always, and
improve performance.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make swsusp call create_basic_memory_bitmaps() before processes are frozen, so
that GFP_KERNEL allocations can be made in it. Additionally, ensure that the
swsusp's userland interface won't be used while either pm_suspend_disk() or
software_resume() is being executed.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We forget to increase device_available if there's an error in snapshot_open(),
so the snapshot device cannot be open at all after snapshot_open() has
returned an error.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make swsusp use memory bitmaps instead of page flags for marking 'nosave' and
free pages. This allows us to 'recycle' two page flags that can be used for
other purposes. Also, the memory needed to store the bitmaps is allocated
when necessary (ie. before the suspend) and freed after the resume which is
more reasonable.
The patch is designed to minimize the amount of changes and there are some
nice simplifications and optimizations possible on top of it. I am going to
implement them separately in the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace direct invocations of SetPageNosave(), SetPageNosaveFree() etc. with
calls to inline functions that can be changed in subsequent patches without
modifying the code calling them.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
refrigerator() can miss a wakeup, "wait event" loop needs a proper memory
ordering.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Powermac G5 suspend to disk implementation. The code is platform
agnostic but only tested on powermac, no other 64-bit powerpc
machines.
Because nvidiafb still breaks suspend I have marked it EXPERIMENTAL on
powermac and because I can't test it and some lowlevel code will need
changes it is BROKEN on all other 64-bit platforms.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (231 commits)
[PATCH] i386: Don't delete cpu_devs data to identify different x86 types in late_initcall
[PATCH] i386: type may be unused
[PATCH] i386: Some additional chipset register values validation.
[PATCH] i386: Add missing !X86_PAE dependincy to the 2G/2G split.
[PATCH] x86-64: Don't exclude asm-offsets.c in Documentation/dontdiff
[PATCH] i386: avoid redundant preempt_disable in __unlazy_fpu
[PATCH] i386: white space fixes in i387.h
[PATCH] i386: Drop noisy e820 debugging printks
[PATCH] x86-64: Fix allnoconfig error in genapic_flat.c
[PATCH] x86-64: Shut up warnings for vfat compat ioctls on other file systems
[PATCH] x86-64: Share identical video.S between i386 and x86-64
[PATCH] x86-64: Remove CONFIG_REORDER
[PATCH] x86-64: Print type and size correctly for unknown compat ioctls
[PATCH] i386: Remove copy_*_user BUG_ONs for (size < 0)
[PATCH] i386: Little cleanups in smpboot.c
[PATCH] x86-64: Don't enable NUMA for a single node in K8 NUMA scanning
[PATCH] x86: Use RDTSCP for synchronous get_cycles if possible
[PATCH] i386: Add X86_FEATURE_RDTSCP
[PATCH] i386: Implement X86_FEATURE_SYNC_RDTSC on i386
[PATCH] i386: Implement alternative_io for i386
...
Fix up trivial conflict in include/linux/highmem.h manually.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to work on cleaning up the relationship between kobjects, ksets and
ktypes. The removal of 'struct subsystem' is the first step of this,
especially as it is not really needed at all.
Thanks to Kay for fixing the bugs in this patch.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
o virt_to_page() call should be used on kernel linear addresses and not
on kernel text and data addresses. Swsusp code uses it on kernel data
(statically allocated swsusp_header).
o Allocate swsusp_header dynamically so that virt_to_page() can be used
safely.
o I am changing this because in next few patches, __pa() on x86_64 will
no longer support kernel text and data addresses and hibernation breaks.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
o __pa() should be used only on kernel linearly mapped virtual addresses
and not on kernel text and data addresses.
o Hibernation code needs to determine the physical address associated
with kernel symbol to mark a section boundary which contains pages which
don't have to be saved and restored during hibernate/resume operation.
o Move this piece of code in arch dependent section. So that architectures
which don't have kernel text/data mapped into kernel linearly mapped
region can come up with their own ways of determining physical addresses
associated with a kernel text.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch changes the docs and behaviour from "all states valid" to "no
states valid" if no .valid callback is assigned. Users of pm_ops that only
need mem sleep can assign pm_valid_only_mem without any overhead, others
will require more elaborate callbacks.
Now that all users of pm_ops have a .valid callback this is a safe thing to
do and prevents things from getting messy again as they were before.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Looks-okay-to: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Almost all users of pm_ops only support mem sleep, don't check in .valid and
don't reject any others in .prepare so users can be confused if they check
/sys/power/state, especially when new states are added (these would then
result in s-t-r although they're supposed to be something different).
This patch implements a generic pm_valid_only_mem function that is then
exported for users and puts it to use in almost all existing pm_ops.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: linux-pm@lists.linux-foundation.org
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the firmware disk suspend mode which is the wrong approach,
it is supposed to be used for implementing firmware-based disk suspend but
cannot actually be used for that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series cleans up some misconceptions about pm_ops. Some users of
the pm_ops structure attempt to use it to stop the user from entering suspend
to disk, this, however, is not possible since the user can always use
"shutdown" in /sys/power/disk and then the pm_ops are never invoked. Also,
platforms that don't support suspend to disk simply should not allow
configuring SOFTWARE_SUSPEND (read the help text on it, it only selects
suspend to disk and nothing else, all the other stuff depends on PM).
The pm_ops structure is actually intended to provide a way to enter
platform-defined sleep states (currently supported states are "standby" and
"mem" (suspend to ram)) and additionally (if SOFTWARE_SUSPEND is configured)
allows a platform to support a platform specific way to enter low-power mode
once everything has been saved to disk. This is currently only used by ACPI
(S4).
This patch:
The pm_ops.pm_disk_mode is used in totally bogus ways since nobody really
seems to understand what it actually does.
This patch clarifies the pm_disk_mode description.
It also removes all the arm and sh users that think they can veto suspend to
disk via pm_ops; not so since the user can always do echo shutdown >
/sys/power/disk, they need to find a better way involving Kconfig or such.
ACPI is the only user left with a non-zero pm_disk_mode.
The patch also sets the default mode to shutdown again, but when a new pm_ops
is registered its pm_disk_mode is selected as default, that way the default
stays for ACPI where it is apparently required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After some more discussion this patch replaces it:
From: Johannes Berg <johannes@sipsolutions.net>
Subject: suspend: add arch irq disable/enable hooks
For powermac, we need to do some things between suspending devices and
device_power_off, for example setting the decrementer. This patch
allows architectures to define arch_s2ram_{en,dis}able_irqs in their
asm/suspend.h to have control over this step.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a bug in the swsusp's memory shrinker that causes some systems using
highmem to refuse to suspend to disk if image_size is set above 1/2 of
available RAM.
Special thanks to Jiri Slaby for reporting the problem and assistance in
debugging it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 94985134b7 and
insteads removes the WARN_ON() that caused that commit in the first
place.
The problem is that we call disable_nonboot_cpus() in swsusp before
powering down the system in order to avoid triggering the WARN_ON()
in arch/x86_64/kernel/acpi/sleep.c:init_low_mapping() and this doesn't
work well on Thomas' system.
So instead, remove the WARN_ON() in arch/x86_64/kernel/acpi/sleep.c:
init_low_mapping(), which triggers every time during the suspend to disk
in the platform mode, as the potential problem it is related to doesn't
seem to occur in practice.
[ I think we might want to disallow the case of multiple users of that
mm, or something. Normally, playing with the current process page
tables on the current CPU should be fine as long as we don't have
other threads using those tables at the same time..
Anyway, not pretty, but better than the warning or the lockup - Linus ]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It causes extra moon icons blinking on x60, and breaks at least two other
systems.
During resume, we do not know that "reboot"/"shutdown" method was used, so
we assume "plaform" and call BIOS, anyway...
This is 2.6.21 material, and should fix 2 or 3 regressions from 2.6.20.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SNAPSHOT_S2RAM ioctl does not disable the nonboot CPUs before entering
the suspend, although it should do this.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the console is in VT_AUTO+KD_GRAPHICS mode, switching to the
SUSPEND_CONSOLE fails, resulting in vt_waitactive() waiting indefinitely or
until the task is interrupted. This patch tests if a console switch can
occur in set_console() and returns early if a console switch is not
possible.
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Andrew Johnson <ajohnson@intrinsyc.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prevent the WARN_ON() in arch/x86_64/kernel/acpi/sleep.c:init_low_mapping()
from triggering by disabling nonboot CPUs before we finally enter the
platform suspend.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If swsusp is using the platform mode during the resume and the image cannot
be read, the platform mode should be switched off before software_resume()
returns. Make it happen.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the outdated and inaccurate description of the software suspend in
Kconfig.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change /sys/power/state to not advertise any valid states (except for disk
if SOFTWARE_SUSPEND is enabled) when no pm_ops have been set so userspace
can easily discover what states should be available.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Macheck <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make the userland interface of swsusp call pm_ops->finish() after
enable_nonboot_cpus() and before resume_device(), as indicated by the recent
discussion on Linux-PM (cf.
http://lists.osdl.org/pipermail/linux-pm/2006-November/004164.html).
This patch changes the SNAPSHOT_PMOPS ioctl so that its first function,
PMOPS_PREPARE, only sets a switch turning the platform suspend mode on, and
its last function, PMOPS_FINISH, only checks if the platform mode is enabled.
This should allow the older userland tools to work with new kernels without
any modifications.
The changes here only affect the userland interface of swsusp.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Greg KH <greg@kroah.com>
Cc: Nigel Cunningham <nigel@suspend2.net>
Cc: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The compiler will do that. And if it doesn't, we don't want to either ;)
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Greg KH <greg@kroah.com>
Cc: Nigel Cunningham <nigel@suspend2.net>
Cc: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the ordering of code in kernel/power/user.c so that device_suspend() is
called before disable_nonboot_cpus() and device_resume() is called after
enable_nonboot_cpus(). This is needed to make the userland suspend call
pm_ops->finish() after enable_nonboot_cpus() and before device_resume(), as
indicated by the recent discussion on Linux-PM (cf.
http://lists.osdl.org/pipermail/linux-pm/2006-November/004164.html).
The changes here only affect the userland interface of swsusp.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Greg KH <greg@kroah.com>
Cc: Nigel Cunningham <nigel@suspend2.net>
Cc: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the ordering of code in kernel/power/disk.c so that device_suspend() is
called before disable_nonboot_cpus() and platform_finish() is called after
enable_nonboot_cpus() and before device_resume(), as indicated by the recent
discussion on Linux-PM (cf.
http://lists.osdl.org/pipermail/linux-pm/2006-November/004164.html).
The changes here only affect the built-in swsusp.
[alexey.y.starikovskiy@linux.intel.com: fix LED blinking during image load]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Greg KH <greg@kroah.com>
Cc: Nigel Cunningham <nigel@suspend2.net>
Cc: Patrick Mochel <mochel@digitalimplant.org>
Cc: Alexey Starikovskiy <alexey.y.starikovskiy@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As indicated in a recent thread on Linux-PM, it's necessary to call
pm_ops->finish() before devce_resume(), but enable_nonboot_cpus() has to be
called before pm_ops->finish() (cf.
http://lists.osdl.org/pipermail/linux-pm/2006-November/004164.html). For
consistency, it seems reasonable to call disable_nonboot_cpus() after
device_suspend().
This way the suspend code will remain symmetrical with respect to the resume
code and it may allow us to speed up things in the future by suspending and
resuming devices and/or saving the suspend image in many threads.
The following series of patches reorders the suspend and resume code so that
nonboot CPUs are disabled after devices have been suspended and enabled before
the devices are resumed. It also causes pm_ops->finish() to be called after
enable_nonboot_cpus() wherever necessary.
This patch:
Change the ordering of code in kernel/power/main.c so that device_suspend()
is called before disable_nonboot_cpus() and pm_ops->finish() is called after
enable_nonboot_cpus() and before device_resume(), as indicated by recent
discussion on Linux-PM
(cf. http://lists.osdl.org/pipermail/linux-pm/2006-November/004164.html).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Greg KH <greg@kroah.com>
Cc: Nigel Cunningham <nigel@suspend2.net>
Cc: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
nr_free_pages is now a simple access to a global variable. Make it a macro
instead of a function.
The nr_free_pages now requires vmstat.h to be included. There is one
occurrence in power management where we need to add the include. Directly
refrer to global_page_state() there to clarify why the #include was added.
[akpm@osdl.org: arm build fix]
[akpm@osdl.org: sparc64 build fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is again simplifies some of the VM counter calculations through the use
of the ZVC consolidated counters.
[michal.k.k.piotrowski@gmail.com: build fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently ARM and MIPS both have nearly identical copies of the APM
emulation code in their arch code. Add yet another copy of it to
drivers char and make it selectable through SYS_SUPPORTS_APM_EMULATION.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In the kernels later than 2.6.19 there is a regression that makes swsusp
fail if the resume device is not explicitly specified.
It can be fixed by adding an additional parameter to
mm/swapfile.c:swap_type_of() allowing us to pass the (struct block_device
*) corresponding to the first available swap back to the caller.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Deprecate the old "legacy" PM API, and more importantly default it to "n".
Virtually nothing in-tree uses it any more.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, to tell a task that it should go to the refrigerator, we set the
PF_FREEZE flag for it and send a fake signal to it. Unfortunately there
are two SMP-related problems with this approach. First, a task running on
another CPU may be updating its flags while the freezer attempts to set
PF_FREEZE for it and this may leave the task's flags in an inconsistent
state. Second, there is a potential race between freeze_process() and
refrigerator() in which freeze_process() running on one CPU is reading a
task's PF_FREEZE flag while refrigerator() running on another CPU has just
set PF_FROZEN for the same task and attempts to reset PF_FREEZE for it. If
the refrigerator wins the race, freeze_process() will state that PF_FREEZE
hasn't been set for the task and will set it unnecessarily, so the task
will go to the refrigerator once again after it's been thawed.
To solve first of these problems we need to stop using PF_FREEZE to tell
tasks that they should go to the refrigerator. Instead, we can introduce a
special TIF_*** flag and use it for this purpose, since it is allowed to
change the other tasks' TIF_*** flags and there are special calls for it.
To avoid the freeze_process()-refrigerator() race we can make
freeze_process() to always check the task's PF_FROZEN flag after it's read
its "freeze" flag. We should also make sure that refrigerator() will
always reset the task's "freeze" flag after it's set PF_FROZEN for it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, if a task is stopped (ie. it's in the TASK_STOPPED state), it
is considered by the freezer as unfreezeable. However, there may be a race
between the freezer and the delivery of the continuation signal to the task
resulting in the task running after we have finished freezing the other
tasks. This, in turn, may lead to undesirable effects up to and including
data corruption.
To prevent this from happening we first need to make the freezer consider
stopped tasks as freezeable. For this purpose we need to make freezeable()
stop returning 0 for these tasks and we need to force them to enter the
refrigerator. However, if there's no continuation signal in the meantime,
the stopped tasks should remain stopped after all processes have been
thawed, so we need to send an additional SIGSTOP to each of them before
waking it up.
Also, a stopped task that has just been woken up should first check if
there's a freezing request for it and go to the refrigerator if that's the
case.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- move some file_operations structs into the .rodata section
- move static strings from policy_types[] array into the .rodata section
- fix generic seq_operations usages, so that those structs may be defined
as "const" as well
[akpm@osdl.org: couple of fixes]
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The new shared APM emulation just like its ARM and MIPS predecessors uses
pm_suspend() which was only exported on SH. Move export to close to it's
definition where it really should be anyway.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cleanup write-only variable, suggested by D Binderman.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 'testproc' swsusp debug mode thaws tasks twice in a row, which is _very_
confusing. Fix that.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move all labels in the swsusp code to the second column, so that they won't
fool diff -p.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@suspend2.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the loop from freeze_processes() to a separate function and call it
independently for user space processes and kernel threads so that the order
of freezing tasks is clearly visible.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@suspend2.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the loop from thaw_processes() to a separate function and call it
independently for kernel threads and user space processes so that the order
of thawing tasks is clearly visible.
Drop thaw_kernel_threads() which is never used.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@suspend2.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The power management semaphore is only used as mutex, so convert it.
[akpm@osdl.org: fix rotten bug]
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix http://bugzilla.kernel.org/show_bug.cgi?id=7534
Fix the freezing of processes so that it won't fail if there is a traced
process the parent of which has been stopped.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: maurice barnum <pixi+kbug@burble.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make swsusp measure and print the time needed to shrink memory during the
suspend.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@suspend2.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make swsusp support i386 systems with PAE or without PSE.
This is done by creating temporary page tables located in resume-safe page
frames before the suspend image is restored in the same way as x86_64 does
it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andi Kleen <ak@suse.de>
Cc: Dave Jones <davej@redhat.com>
Cc: Nigel Cunningham <ncunningham@linuxmail.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modify process thawing so that we can thaw kernel space without thawing
userspace, and thaw kernelspace first. This will be useful in later
patches, where I intend to get swsusp thawing kernel threads only before
seeking to free memory.
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Minor whitespace and formatting modifications for the freezer.
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The freezer currently prints an '=' for every process that is frozen. This
is pretty pointless, as the equals sign says nothing about which process is
frozen, and makes logs look messier (especially if there were a large
number of processes running). All we really need to know is that we
started trying to freeze processes and what processes (if any) failed to
freeze, or that we succeeded.
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move process freezing functions from include/linux/sched.h to freezer.h, so
that modifications to the freezer or the kernel configuration don't require
recompiling just about everything.
[akpm@osdl.org: fix ueagle driver]
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
At some point after 2.6.13, in-kernel software suspend got "incomplete" for
the so-called "platform" mode. pm_ops->prepare() is never called. A
visible sign of this is the "moon" light on thinkpads not flashing during
suspend. Fix by readding the pm_ops->prepare call during suspend.
Signed-off-by: Stefan Seyfried <seife@suse.de>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
swsusp uses GFP_ATOMIC, but it can afford to use __GFP_WAIT, which will
permit it to reclaim clean pagecache instead of emitting scary
page-allocation-failure messages.
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently swsusp saves the contents of highmem pages by copying them to the
normal zone which is quite inefficient (eg. it requires two normal pages
to be used for saving one highmem page). This may be improved by using
highmem for saving the contents of saveable highmem pages.
Namely, during the suspend phase of the suspend-resume cycle we try to
allocate as many free highmem pages as there are saveable highmem pages.
If there are not enough highmem image pages to store the contents of all of
the saveable highmem pages, some of them will be stored in the "normal"
memory. Next, we allocate as many free "normal" pages as needed to store
the (remaining) image data. We use a memory bitmap to mark the allocated
free pages (ie. highmem as well as "normal" image pages).
Now, we use another memory bitmap to mark all of the saveable pages
(highmem as well as "normal") and the contents of the saveable pages are
copied into the image pages. Then, the second bitmap is used to save the
pfns corresponding to the saveable pages and the first one is used to save
their data.
During the resume phase the pfns of the pages that were saveable during the
suspend are loaded from the image and used to mark the "unsafe" page
frames. Next, we try to allocate as many free highmem page frames as to
load all of the image data that had been in the highmem before the suspend
and we allocate so many free "normal" page frames that the total number of
allocated free pages (highmem and "normal") is equal to the size of the
image. While doing this we have to make sure that there will be some extra
free "normal" and "safe" page frames for two lists of PBEs constructed
later.
Now, the image data are loaded, if possible, into their "original" page
frames. The image data that cannot be written into their "original" page
frames are loaded into "safe" page frames and their "original" kernel
virtual addresses, as well as the addresses of the "safe" pages containing
their copies, are stored in one of two lists of PBEs.
One list of PBEs is for the copies of "normal" suspend pages (ie. "normal"
pages that were saveable during the suspend) and it is used in the same way
as previously (ie. by the architecture-dependent parts of swsusp). The
other list of PBEs is for the copies of highmem suspend pages. The pages
in this list are restored (in a reversible way) right before the
arch-dependent code is called.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To be able to use swap files as suspend storage from the userland suspend
tools we need an additional ioctl() that will allow us to provide the kernel
with both the swap header's offset and the identification of the resume
partition.
The new ioctl() should be regarded as a replacement for the
SNAPSHOT_SET_SWAP_FILE ioctl() that from now on will be considered as
obsolete, but has to stay for backwards compatibility of the interface.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the kernel command line parameter "resume_offset=" allowing us to specify
the offset, in <PAGE_SIZE> units, from the beginning of the partition pointed
to by the "resume=" parameter at which the swap header is located.
This offset can be determined, for example, by an application using the FIBMAP
ioctl to obtain the swap header's block number for given file.
[akpm@osdl.org: we don't know what type sector_t is]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make swsusp use block device offsets instead of swap offsets to identify swap
locations and make it use the same code paths for writing as well as for
reading data.
This allows us to use the same code for handling swap files and swap
partitions and to simplify the code, eg. by dropping rw_swap_page_sync().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Gerald Schaefer