Replace inode_setattr with opencoded variants of it in all callers. This
moves the remaining call to vmtruncate into the filesystem methods where it
can be replaced with the proper truncate sequence.
In a few cases it was obvious that we would never end up calling vmtruncate
so it was left out in the opencoded variant:
spufs: explicitly checks for ATTR_SIZE earlier
btrfs,hugetlbfs,logfs,dlmfs: explicitly clears ATTR_SIZE earlier
ufs: contains an opencoded simple_seattr + truncate that sets the filesize just above
In addition to that ncpfs called inode_setattr with handcrafted iattrs,
which allowed to trim down the opencoded variant.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add another device ID as listed in the vendor driver version
0003.0825.2009.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are only 6 elements in the cb_pcidda_boards[] array so the
original code read past the end. After this change nothing uses N_BOARDS
so I removed the definition.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds some device ids.
The list of supported devices was extracted from realteks driver package.
(0x050d, 0x815F) and (0x0df6, 0x004b) are not in the official list of
supported devices and may not work correctly.
In case of problems with these, they should probably be removed from the list.
Signed-off-by: Florian Schilhabel <florian.c.schilhabel@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In commit bbfb5652, the spacing in the definitions of eqMacAddr and cpMacAddr
in drivers/staging/rtl8187se/r8180_core.c were changed to conform to kernel
standards. These definitions were duplicates of lines found in
drivers/staging/rtl8187se/ieee80211/dot11d.h. Once the change was made, the
following warnings were emitted:
CC [M] drivers/staging/rtl8187se/r8180_core.o
drivers/staging/rtl8187se/r8180_core.c:69:0: warning: "eqMacAddr" redefined
drivers/staging/rtl8187se/ieee80211/dot11d.h:39:0: note: this is the location of the previous definition
drivers/staging/rtl8187se/r8180_core.c:70:0: warning: "cpMacAddr" redefined
drivers/staging/rtl8187se/ieee80211/dot11d.h:40:0: note: this is the location of the previous definition
The fix is to keep only the difinition in the header file.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I got a wlags49_h2 driver build error in linux-next when CONFIG_SYSFS is not set.
CC [M] drivers/staging/wlags49_h2/wl_cs.o
In file included from drivers/staging/wlags49_h2/wl_cs.c:104:
drivers/staging/wlags49_h2/wl_sysfs.h: In function ‘register_wlags_sysfs’:
drivers/staging/wlags49_h2/wl_sysfs.h:5: error: parameter name omitted
drivers/staging/wlags49_h2/wl_sysfs.h: In function ‘unregister_wlags_sysfs’:
drivers/staging/wlags49_h2/wl_sysfs.h:6: error: parameter name omitted
make[1]: *** [drivers/staging/wlags49_h2/wl_cs.o] Error 1
make: *** [_module_drivers/staging/wlags49_h2] Error 2
This is due a wrong function definition (it does not include parameters names).
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On ia64, the build fails with incompatible implicit definition of strlen.
This patch adds the <linux/string.h> include to get the real prototype.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a possible race condition when hv_utils starts to load immediately
after hv_vmbus is loading - null pointer error could happen.
This patch added wait/completion to ensure all channels are ready before
vmbus loading completes. So another module won't have any uninitialized channel.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I received a report that AI streaming acquisitions do not work properly
for the adl_pci9111 driver when convert_src is TRIG_TIMER and
scan_begin_src is TRIG_FOLLOW (and scan_begin_arg is therefore 0). This
seems to be down to the incorrect setting of dev_private->scan_delay in
pci9111_ai_do_cmd(). Under the previously stated conditions,
dev_private->scan_delay ends up set to (unsigned int)-1, but it ought to
be set to 0. The function sets it to 0 initially, and it only makes
sense to change it if both convert_src and scan_begin_src are set to
TRIG_TIMER.
Note: 'scan_delay' is the number of unwanted scans to discard after each
valid scan. The hardware does not support 'scan' timing as such, just a
regularly paced conversion timer (with automatic channel switching
between conversions). The driver simulates a scan period that is some
(>1) multiple of the conversion period times the scan length
(chanlist_len samples) by reading chanlist_len samples and discarding
the next scan_delay times chanlist_len samples.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I moved the kfree() down a couple lines after the dereference.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In today linux-next I got a compile warning in staging/batman-adv.
This is due a struct bin_attribute read function prototype change and the driver was not updated.
This patch solves the issue
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
copy_to_user() returns the number of bites remaining but we want to
return a negative error code here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
copy_to_user() returns the number of bytes remaining but we want to
return a negative error code here. These functions are used in the
ioctl handler and the error code gets returned to userspace.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
copy_to_user() returns the number of bytes remaining but we want to
return a negative error code. This is in the ioctl handler and the
error code gets passed to userspace.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Eliminate a NULL or near NULL pointer dereference.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E,E1;
identifier f;
statement S1,S2,S3;
@@
if ((E == NULL && ...) || ...)
{
... when != if (...) S1 else S2
when != E = E1
* E->f
... when any
return ...;
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In each case, the containing function is only called from one place, where
a spin lock is held.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@gfp exists@
identifier fn;
position p;
@@
fn(...) {
... when != spin_unlock
when any
GFP_KERNEL@p
... when any
}
@locked@
identifier gfp.fn;
@@
spin_lock(...)
... when != spin_unlock
fn(...)
@depends on locked@
position gfp.p;
@@
- GFP_KERNEL@p
+ GFP_ATOMIC
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Marek Lindner <lindner_marek@yahoo.de>
Cc: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct at least one of the incorrect specs for a national instrument
data acquisition card DAQCard-6024E. This card has only four different
gain settings (+-10V, +-5V, +-0.5V, +-0.05V).
Signed-off-by: Martin Homuth-Rosemann <homuth-rosemann@gmx.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the dependancy of ni_labpc on mite was missing,
Signed-off-by: Alexander Kurz <linux@kbdbabel.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
index 0aa2b0d..79f5f2e 100644
Fixes Kconfig so the wlags49_h2 and wlags49_h25 drivers can be
selected from menuconfig without having to select another WLAN
driver first. Before it could only be selected when another driver
already selected WIRELESS_EXT. Also adds WEXT_PRIV on which
the driver also depends.
Align help text in Kconfig.
Signed-off-by: Henk de Groot <pe1dnn@amsat.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
phison uses interfaces and data that are built only when
ATA_BMDMA is enabled, so it should depend on that symbol.
drivers/staging/phison/phison.c:43: error: implicit declaration of function 'ATA_BMDMA_SHT'
drivers/staging/phison/phison.c:43: error: initializer element is not constant
drivers/staging/phison/phison.c:43: error: (near initialization for 'phison_sht.module')
drivers/staging/phison/phison.c:47: error: 'ata_bmdma_port_ops' undeclared here (not in a function)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: evan_ko@phison.com
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A new buffer for a packet is created when a icmp packet is received.
This happens in a context with disabled irq. Thus we are not allowed to
sleep or call function which might sleep. kmalloc must be called with
GFP_ATOMIC instead of GFP_KERNEL to ensure that it does not sleep.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Free_netdev is registered as destructor in interface_setup for every
soft_device. This destructor is automatically called from
unregister_netdev and we must not call it again for the freed
net_device.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We must call unregister_netdev when we couldn't initialise the
batman-adv module and the soft_device was registered. There are two
version of the function which we can use:
* unregister_netdevice - removes device
* unregister_netdev - takes rtnl semaphore and remove device
We don't hold the semaphore in an error situation. So we must use
unregister_netdev.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On module shutdown batman-adv would purge the internal packet
queue by sending all remaining packets which could confuse
other nodes. Now, the packets are silently discarded.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Qualcomm development of the MSM SOC framebuffer driver has
diverged significantly from the driver used by Android. This
is a snapshot of our current driver, in all it's agony. We are
putting this in staging to help with the process of converging
the two drivers.
At this point, the driver has been tested only in dumb
framebuffer mode.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
[dwalker@codeaurora.org: added a small compile fix and TODO.]
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Wed, 19 May 2010, Randy Dunlap wrote:
> linux-next of 2010-0519:
> when CONFIG_PCI is not enabled:
>
> drivers/staging/comedi/drivers/mite.c: In function 'mite_init':
> drivers/staging/comedi/drivers/mite.c:89: error: implicit declaration of function 'pci_dev_get'
> drivers/staging/comedi/drivers/mite.c:89: warning: assignment makes pointer from integer without a cast
> make[5]: *** [drivers/staging/comedi/drivers/mite.o] Error 1
This patch fixes the problem.
Signed-off-by: Alexander Kurz <linux@kbdbabel.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Both drivers support directly or indirectly multiple bus types,
hence both are listed independent of bus types.
Signed-off-by: Alexander Kurz <linux@kbdbabel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't allow COMEDI_BUFINFO ioctl if some other file object has locked
the subdevice or has an active command. If there is no active command,
just report back the last buffer position.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the COMEDI_BUFINFO ioctl is used on a subdevice without
asynchronous streaming command support, set 'bytes_read = 0' and
'bytes_written = 0' in the buffer info returned back to the user.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For write(), any data copied to the data buffer after the previously
set up streaming acquisition command has finished won't be used, but a
non-empty write() does not currently return 0 (or -EPIPE on error) after
the command has finished until the data buffer has been filled up.
Change this behavior to return 0 (or -EPIPE) any time after the command
has finished, without bothering to fill up the buffer with more useless
data.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The internal state of an 82C54 counter timer chip will get messed up if
several threads read, write, configure, or check the status of the chip
simultaneously. Protect the register access sequences with a spin lock.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the Advantech PCI-1735U card, including support for a
counter subdevice (based on an 82C54 counter timer chip).
The counter subdevice needs more testing, as the only person I know who
tried it couldn't get it to work!
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Addi-Data PCI drivers for Comedi use sprintf() in their comedi
"attach" routine to construct a string to pass as the name in the call
to request_irq(). All calls to "attach" routine share the same static
buffer for this name, but the contents will differ on each call
(including the comedi device number and the comedi board name). This
changes the name displayed in /proc/interrupts for previous calls to
request_irq() using the same buffer. Just use the board name instead;
it has slightly less information (no comedi device number) but at least
it doesn't change over the lifetime of the IRQ handler.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is not currently possible for more than one of the addi_apci_*
drivers to register themselves with comedi at once because they all use
the same comedi driver name "addi_common". Give them different names.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Touchscreen driver used by intel mid devices. Some clean up by Alan Cox. This
driver is basically ready for upstreaming properly but is tied wrongly to the
SPI layer and needs firmware/SFI changes to fix that.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver handles XG20, XG21, XG40, XG42 chipsets from XGI. They're
also known as Z7,Z9,Z11 chipsets. It's based on the SiS fb driver but
has been heavily modified by XGI to support their newer chipsets.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I2C drivers can use the clientdata-pointer to point to private data. As I2C
devices are not really unregistered, but merely detached from their driver, it
used to be the drivers obligation to clear this pointer during remove() or a
failed probe(). As a couple of drivers forgot to do this, it was agreed that it
was cleaner if the i2c-core does this clearance when appropriate, as there is
no guarantee for the lifetime of the clientdata-pointer after remove() anyhow.
This feature was added to the core with commit
e4a7b9b04d to fix the faulty drivers.
As there is no need anymore to clear the clientdata-pointer, remove all current
occurrences in the drivers to simplify the code and prevent confusion.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
set variable dev_mode in function tm6000_start_stream and check mode
Signed-off-by: Stefan Ringel <stefan.ringel@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Christoph Hellwig
Linus Torvalds
Ben Hutchings
Ozan Çağlayan
Dan Carpenter
Florian Schilhabel
Larry Finger
Javier Martinez Canillas
Jeff Mahoney
Haiyang Zhang
Ian Abbott
Himanshu Chauhan
Tejun Heo
Julia Lawall
Martin Homuth-Rosemann
Alexander Kurz
Henk de Groot
Randy Dunlap
Barry Song
Mike Frysinger
Sven Eckelmann
Marek Lindner
Stepan Moskovchenko
Alexander Kurz
Sreedhara DS
apatard@mandriva.com
Wolfram Sang
Stefan Ringel