Commit Graph

440 Commits

Author SHA1 Message Date
Linus Torvalds ebdea46fec Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (130 commits)
  [ARM] 3856/1: Add clocksource for Intel IXP4xx platforms
  [ARM] 3855/1: Add generic time support
  [ARM] 3873/1: S3C24XX: Add irq_chip names
  [ARM] 3872/1: S3C24XX: Apply consistant tabbing to irq_chips
  [ARM] 3871/1: S3C24XX: Fix ordering of EINT4..23
  [ARM] nommu: confirms the CR_V bit in nommu mode
  [ARM] nommu: abort handler fixup for !CPU_CP15_MMU cores.
  [ARM] 3870/1: AT91: Start removing static memory mappings
  [ARM] 3869/1: AT91: NAND support for DK and KB9202 boards
  [ARM] 3868/1: AT91 hardware header update
  [ARM] 3867/1: AT91 GPIO update
  [ARM] 3866/1: AT91 clock update
  [ARM] 3865/1: AT91RM9200 header updates
  [ARM] 3862/2: S3C2410 - add basic power management support for AML M5900 series
  [ARM] kthread: switch arch/arm/kernel/apm.c
  [ARM] Off-by-one in arch/arm/common/icst*
  [ARM] 3864/1: Refactore sharpsl_pm
  [ARM] 3863/1: Add Locomo SPI Device
  [ARM] 3847/2:  Convert LOMOMO to use struct device for GPIOs
  [ARM] Use CPU_CACHE_* where possible in asm/cacheflush.h
  ...
2006-09-28 14:40:39 -07:00
Andrew Victor 72729910c3 [ARM] 3865/1: AT91RM9200 header updates
This is more preparation for adding support for the new Atmel AT91SAM9
processors.

Changes include:
- Replace AT91_BASE_* with AT91RM9200_BASE_*
- Replace AT91_ID_* with AT91RM9200_ID_*
- ROM, SRAM and UHP address definitions moved to at91rm9200.h.
- The raw AT91_P[ABCD]_* definitions are now depreciated in favour of
the GPIO API.

Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-09-28 11:52:05 +01:00
Paul Mundt ecd9561687 serial: Add SERIAL_SH_SCI_NR_UARTS for sh-sci.
sh-sci needs to be able to define its number of ports to
support, we do this with a config option, like most other
ports do.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2006-09-27 17:32:30 +09:00
Paul Mundt e108b2ca23 serial: Rework sh-sci for driver model.
sh-sci was turning in to an unmaintainable mess, especially with
regards to the port list. This cleans it up quite a bit, and
switches over to a platform device model where subtypes will
register their port list individually in their setup code.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2006-09-27 16:32:13 +09:00
Rafael J. Wysocki e1da95ae38 [PATCH] suspend: make it possible to disable serial console suspend
Hack uart_suspend_port() and uart_resume_port() so that serial console
ports are not suspended if CONFIG_DISABLE_CONSOLE_SUSPEND is set.

This makes it possible to debug the suspend and resume routines of all
device drivers as well as the lowest-level swsusp code with the help of the
serial console.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-26 08:49:03 -07:00
Linus Torvalds 14d1adfc59 Merge git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (114 commits)
  [POWERPC] Fix ohare IDE irq workaround on old powermacs
  [POWERPC] EEH: Power4 systems sometimes need multiple resets.
  [POWERPC] Include <asm/mmu.h> in arch/powerpc/sysdev/fsl_soc.h for phys_addr_t.
  [POWERPC] Demacrofy arch/powerpc/platforms/maple/pci.c
  [POWERPC] Maple U3 HT - reject inappropriate config space access
  [POWERPC] Fix IPIC pending register assignments
  [POWERPC] powerpc: fix building gdb against asm/ptrace.h
  [POWERPC] Remove DISCONTIGMEM cruft from page.h
  [POWERPC] Merge iSeries i/o operations with the rest
  [POWERPC] 40x: Fix debug status register defines
  [POWERPC] Fix compile error in sbc8560
  [POWERPC] EEH: support MMIO enable recovery step
  [POWERPC] EEH: enable MMIO/DMA on frozen slot
  [POWERPC] EEH: code comment cleanup
  [POWERPC] EEH: balance pcidev_get/put calls
  [POWERPC] PPC: Fix xmon stack frame address in backtrace
  [POWERPC] Add AT_PLATFORM value for Xilinx Virtex-4 FX
  [POWERPC] Start arch/powerpc/boot code reorganization
  [POWERPC] Define of_read_ulong helper
  [POWERPC] iseries: eliminate a couple of warnings
  ...
2006-09-22 12:48:03 -07:00
Ben Dooks 71aa7054d3 [ARM] 3793/1: S3C2412: fix wrong serial info struct
Patch from Ben Dooks

The S3C2440 serial info struct is being passed
through the S3C2412 serial info struct probe
routine.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Glexiner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-09-18 13:30:17 +01:00
Paul Mackerras c547fc28ab Merge branch 'linux-2.6' 2006-09-14 07:07:18 +10:00
Paul Mundt 21264136ce sh64: Trivial build fixes.
While we've been sorting out the toolchain fiasco, some of
the code has suffered a bit of bitrot. Building with GCC4
also brings up some more build warnings. Trivial fixes for
both issues.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2006-09-12 14:36:46 +09:00
Paul Mackerras aa43f77939 Merge branch 'merge' 2006-08-31 15:45:48 +10:00
Helge Deller e9422e0915 [SERIAL] 8250: constify some serial structs
- some const- ification and usage of ARRAY_SIZE() in serial drivers

Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-08-30 10:06:14 +01:00
Sergei Shtylyov d21b55d30b [SERIAL] Make uart_match_port() work with all memory mapped UARTs
uart_match_port() always fails with UPIO_MEM32, UPIO_AU, and UPIO_TSI cases.
Since they match to the memory mapped UARTs, they should be handled just like
UPIO_MEM case.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-08-30 10:06:14 +01:00
Peter Horton 737c17561f [SERIAL] Support for Intashield 2 port PCI serial card
Here is a patch that adds support for the Instashield IS-200 2 port PCI
serial card.

Signed-off-by: Peter Horton <pdh@colonel-panic.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-08-27 11:59:49 +01:00
David S. Miller b8b99e857d [SERIAL] sunzilog: Mirror the sunsab serial setup bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-08-23 15:53:39 -07:00
Marc Zyngier 0f4184f73d [SERIAL] sunsab: Fix E250 console with RSC.
This fixes yet another sunsab problem, when console is set to anything
but the first port. The console framework calls sunsab_console_setup
for each port, and we end up setting up a console on a not yet
discovered port, which leads to an Oops. Instead, defer console setup
until the requested port is properly initialized. Tested on an E250
through an RSC console.

Reported by Daniel Smolik <marvin@mydatex.cz>

Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-08-23 15:50:57 -07:00
Paul Mackerras 57cad8084e Merge branch 'merge' 2006-08-01 10:37:25 +10:00
Jeremy Kerr 018a3d1db7 [POWERPC] powermac: Constify & voidify get_property()
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.

powermac platform & macintosh driver changes.

Built for pmac32_defconfig, g5_defconfig

Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-07-31 15:55:05 +10:00
David S. Miller 8a84eb164c [SERIAL] sunzilog: Fix instance enumeration.
Just do a linear enumeration so that we handle sun4d systems
correctly.  As a consequence, eliminate the hard coded keyboard and
mouse channel line values, use the CONS_{KEYB,MS} flags instead.

Also, report the keyboard/mouse Zilog channels just like the uart ones
do.

Signed-off-by: David S. Miller <davem@davemloft.net>
2006-07-21 14:18:25 -07:00
David S. Miller b77d35b722 [SERIAL] sunzilog: Remove duplicate IRQ registry in zs_probe().
We do it now in sunzilog_init() after all devices have been
probed.

Signed-off-by: David S. Miller <davem@davemloft.net>
2006-07-21 14:18:22 -07:00
David S. Miller 67e23a1e60 [SERIAL] sunzilog: Register IRQ after all devices have been probed.
Otherwise we will deref half-initialized channel pointers
and crash in the interrupt handler.

Signed-off-by: David S. Miller <davem@davemloft.net>
2006-07-21 14:18:08 -07:00
David S. Miller bda2f7b480 [SERIAL] sunsab: Get line numbers and table sizing correct.
Table sizing code should look for "se" not "su" nodes.

The chip at the lower address should get the first index.

Signed-off-by: David S. Miller <davem@davemloft.net>
2006-07-21 14:18:01 -07:00
Marc Zyngier 44f2650b13 [SPARC64] Fix sunsab ports ordering
Register second SAB port before the first one, as serial A is wired to
it, and expected to appear as ttyS0.

Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-07-21 14:17:57 -07:00
David S. Miller 5b4bbb3d78 [SERIAL] sunsab: Fix significant typo in sab_probe()
Instead of initializing both ports of a SAB device
properly, we were setting up the first port
structure twice and ending up only with the second
port, oops.

Signed-off-by: David S. Miller <davem@davemloft.net>
2006-07-14 17:00:25 -07:00
David S. Miller c964521c54 [SERIAL] sunsu: Report keyboard and mouse ports in kernel log.
Otherwise there is no explicit mention of these devices.

Signed-off-by: David S. Miller <davem@davemloft.net>
2006-07-14 17:00:23 -07:00
Linus Torvalds ab6cf0d0cb Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (53 commits)
  [MIPS] sparsemem: fix crash in show_mem
  [MIPS] vr41xx: Update workpad setup function
  [MIPS] vr41xx: Update e55 setup function
  [MIPS] vr41xx: Removed old v2.4 VRC4173 driver
  [MIPS] vr41xx: Move IRQ numbers to asm-mips/vr41xx/irq.h
  [MIPS] MIPSsim: Build fix, rename sim_timer_setup -> plat_timer_setup.
  [MIPS] Remove unused code.
  [MIPS] IP22 Fix brown paper bag in RTC code.
  [MIPS] Atlas, Malta, SEAD: Don't disable interrupts in mips_time_init().
  [MIPS] Replace board_timer_setup function pointer by plat_timer_setup.
  [MIPS] Nuke redeclarations of board_time_init.
  [MIPS] Remove redeclarations of setup_irq().
  [MIPS] Nuke redeclarations of board_timer_setup.
  [MIPS] Print out TLB handler assembly for debugging.
  [MIPS] SMTC: Reformat to Linux style.
  [MIPS] MIPSsim: Delete redeclaration of ll_local_timer_interrupt.
  [MIPS] IP27: Reformatting.
  [MIPS] IP27: Invoke setup_irq for timer interrupt so proc stats will be shown.
  [MIPS] IP27: irq_chip startup method returns unsigned int.
  [MIPS] IP27: struct irq_desc member handler was renamed to chip.
  ...
2006-07-13 16:57:04 -07:00
Linus Torvalds 7b69a4c360 Merge master.kernel.org:/home/rmk/linux-2.6-serial
* master.kernel.org:/home/rmk/linux-2.6-serial:
  [SERIAL] 8250: sysrq deadlock fix
  [SERIAL] 8250: add tsi108 serial support
  [SERIAL] IP22: fix serial console hangs
  [SERIAL] dz: Fix compilation error
2006-07-13 16:38:02 -07:00
Yoichi Yuasa 66151bbd20 [MIPS] vr41xx: Move IRQ numbers to asm-mips/vr41xx/irq.h
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2006-07-13 21:26:19 +01:00
David S. Miller 91d1ed1a6d [SERIAL] sunsu: Handle keyboard and mouse ports directly.
The sunsu_ports[] array exists merely to be able to easily
use an integer index to get at the proper serial console
port struct.

We size this only for real ports, not for the keyboard and
mouse, and thus keyboard and mouse port registration would
fail.

Fix this by dynamically allocating the port struct for the
keyboard and mouse, instead of using the sunsu_ports[]
array.

Signed-off-by: David S. Miller <davem@davemloft.net>
2006-07-13 01:50:11 -07:00
Andrew Morton 68aa2c0d4a [SERIAL] 8250: sysrq deadlock fix
Fix http://bugzilla.kernel.org/show_bug.cgi?id=6716

Doing a sysrq over a serial line into an SMP machine presently deadlocks.

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-07-09 21:11:10 +01:00
Zang Roy-r61911 3be91ec738 [SERIAL] 8250: add tsi108 serial support
The following patch gets rid of CONFIG_TSI108_BRIDGE.  I add UPIO_TSI to
handle IIR and IER register in serial_in and serial_out.

(1) the reason to rewrite serial_in:

    TSI108 rev Z1 version ERRATA.  Reading the UART's Interrupt
    Identification Register (IIR) clears the Transmit Holding Register
    Empty (THRE) and Transmit buffer Empty (TEMP) interrupts even if they
    are not enabled in the Interrupt Enable Register (IER).  This leads to
    loss of the interrupts.  Interrupts are not cleared when reading UART
    registers as 32-bit word.

(2) the reason to rewrite serial_out:

    Check for UART_IER_UUE bit in the autoconfig routine.  This section
    of autoconfig is excluded for Tsi108/109 because bits 7 and 6 are
    reserved for internal use.  They are R/W bits.  In addition to
    incorrect identification, changing these bits (from 00) will make
    Tsi108/109 UART non-functional.

Signed-off-by: Roy Zang	<tie-fei.zang@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-07-09 21:11:09 +01:00
Julien BLACHE c65b15cfd6 [SERIAL] IP22: fix serial console hangs
The patch below fixes serial console hangs as seen on IP22
machines. Typically, while booting, the machine hangs for ~1 minute
displaying "INIT: ", then the same thing happens again when init
enters in the designated runlevel and finally the getty process on
ttyS0 hangs indefinitely (though strace'ing it helps).

strace (-e raw=ioctl, otherwise the ioctl() translation is utterly
bogus) reveals that getty hangs on ioctl() 0x540f which happens to be
TCSETSW (I saw it hang on another console ioctl() but couldn't
reproduce that one).

A diff between ip22zilog and sunzilog revealed the following
differences:
 1. the channel A flag being set on up.port.flags instead of up.flags
 2. the channel A flag being set on what is marked as being channel B
 3. sunzilog has a call to uart_update_timeout(port, termios->c_cflag, baud);
    at the end of sunzilog_set_termios(), which ip22zilog lacks (on
    purpose ?)

The patch below addresses point 1 and fixes the serial console hangs
just fine. However point 2 should be investigated by someone familiar
with the IP22 Zilog; it's probably OK as is but even if it is, a
comment in ip22zilog.c is badly needed.

Point 3 is left as an exercise for whoever feels like digging into
ip22zilog :)

These are the main obvious differences between ip22zilog and
sunzilog. Newer versions of sunzilog (Linus's git tree as of today)
are more close to ip22zilog as the sbus_{write,read}b have been
changed into simple {write,read}b, which shrinks the diff by a fair
amount. Resyncing both drivers should be doable in a few hours time
now for someone familiar with the IP22 Zilog hardware.

Signed-off-by: Julien BLACHE <jb@jblache.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-07-09 21:11:09 +01:00
Martin Michlmayr d608ab9917 [SERIAL] dz: Fix compilation error
Fix the following compilation error in the dz serial driver that got
introduced with the "kernel console should send CRLF not LFCR" change.

  CC      drivers/serial/dz.o
drivers/serial/dz.c: In function 'dz_console_putchar':
drivers/serial/dz.c:679: error: 'uport' undeclared (first use in this function)
drivers/serial/dz.c:679: error: (Each undeclared identifier is reported only once
drivers/serial/dz.c:679: error: for each function it appears in.)

Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-07-09 21:11:09 +01:00
Andrew Victor 20e652761c [ARM] 3710/1: AT91 Serial: Use GPIO API
Patch from Andrew Victor

The AT91RM9200 errata work-around should be using the GPIO API and not
accessing the PIO registers directly.

Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-07-05 14:31:13 +01:00
Linus Torvalds 075395d228 Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial:
  [SERIAL] Ensure 8250_pci quirks are not marked __devinit
  [SERIAL] Convert fifosize to an unsigned int
2006-07-03 21:31:05 -07:00
Linus Torvalds 912b2539e1 Merge git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  powerpc: add defconfig for Freescale MPC8349E-mITX board
  powerpc: Add base support for the Freescale MPC8349E-mITX eval board
  Documentation: correct values in MPC8548E SEC example node
  [POWERPC] Actually copy over i8259.c to arch/ppc/syslib this time
  [POWERPC] Add new interrupt mapping core and change platforms to use it
  [POWERPC] Copy i8259 code back to arch/ppc
  [POWERPC] New device-tree interrupt parsing code
  [POWERPC] Use the genirq framework
  [PATCH] genirq: Allow fasteoi handler to retrigger disabled interrupts
  [POWERPC] Update the SWIM3 (powermac) floppy driver
  [POWERPC] Fix error handling in detecting legacy serial ports
  [POWERPC] Fix booting on Momentum "Apache" board (a Maple derivative)
  [POWERPC] Fix various offb and BootX-related issues
  [POWERPC] Add a default config for 32-bit CHRP machines
  [POWERPC] fix implicit declaration on cell.
  [POWERPC] change get_property to return void *
2006-07-03 15:28:34 -07:00
Ingo Molnar 13e83599d2 [PATCH] lockdep: annotate serial
Teach special (dual-initialized) locking code to the lock validator.  Has no
effect on non-lockdep kernels.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-03 15:27:06 -07:00
Bjorn Helgaas cb6358eb69 [PATCH] SERIAL: allow shared 8250_pnp interrupts
PNP devices can use shared interrupts, so check to see whether we'll need
SA_SHIRQ for request_irq().

The builtin PDH UART on the HP rx8640 is an example of an ACPI/PNP device
that uses a shareable level-triggered, active-low interrupt.  The interrupt
can be shared in very large I/O configurations or by artificially lowering
IA64_DEF_LAST_DEVICE_VECTOR.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Matthieu Castet <castet.matthieu@free.fr>
Cc: Li Shaohua <shaohua.li@intel.com>
Cc: Len Brown <len.brown@intel.com>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-03 15:26:58 -07:00
Russell King 61a116ef29 [SERIAL] Ensure 8250_pci quirks are not marked __devinit
The 8250_pci quirks must not be marked __devinit since they may
be used from parport_serial.  We only really need to mark those
which might be used by cards recognised by parport_serial, but
that wouldn't allow static checking.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-07-03 15:22:35 +01:00
Benjamin Herrenschmidt 0ebfff1491 [POWERPC] Add new interrupt mapping core and change platforms to use it
This adds the new irq remapper core and removes the old one.  Because
there are some fundamental conflicts with the old code, like the value
of NO_IRQ which I'm now setting to 0 (as per discussions with Linus),
etc..., this commit also changes the relevant platform and driver code
over to use the new remapper (so as not to cause difficulties later
in bisecting).

This patch removes the old pre-parsing of the open firmware interrupt
tree along with all the bogus assumptions it made to try to renumber
interrupts according to the platform. This is all to be handled by the
new code now.

For the pSeries XICS interrupt controller, a single remapper host is
created for the whole machine regardless of how many interrupt
presentation and source controllers are found, and it's set to match
any device node that isn't a 8259.  That works fine on pSeries and
avoids having to deal with some of the complexities of split source
controllers vs. presentation controllers in the pSeries device trees.

The powerpc i8259 PIC driver now always requests the legacy interrupt
range. It also has the feature of being able to match any device node
(including NULL) if passed no device node as an input. That will help
porting over platforms with broken device-trees like Pegasos who don't
have a proper interrupt tree.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-07-03 21:36:01 +10:00
Thomas Gleixner 40663cc7f1 [PATCH] irq-flags: serial: Use the new IRQF_ constants
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-02 13:58:53 -07:00
Russell King 947deee890 [SERIAL] Convert fifosize to an unsigned int
Some UARTs have more than 255 bytes of FIFO, which can't be
represented by an unsigned char.  Change the kernel's internal
structure to be an unsigned int, but still export an unsigned char
via the TIOCGSERIAL ioctl.  If the TIOCSSERIAL ioctl provides a
fifo size of 0, assume this means "don't change" otherwise we'll
corrupt the larger fifo sizes.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-07-02 20:45:51 +01:00
Linus Torvalds 9262e9149f Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Kill sun4v virtual device layer.
  [SERIAL] sunhv: Convert to of_driver layer.
  [SPARC64]: Mask out top 8-bits in physical address when building resources.
  [SERIAL] sunsu: Missing return statement in su_probe().
2006-06-30 15:40:35 -07:00
Linus Torvalds 22a3e233ca Merge git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
  Remove obsolete #include <linux/config.h>
  remove obsolete swsusp_encrypt
  arch/arm26/Kconfig typos
  Documentation/IPMI typos
  Kconfig: Typos in net/sched/Kconfig
  v9fs: do not include linux/version.h
  Documentation/DocBook/mtdnand.tmpl: typo fixes
  typo fixes: specfic -> specific
  typo fixes in Documentation/networking/pktgen.txt
  typo fixes: occuring -> occurring
  typo fixes: infomation -> information
  typo fixes: disadvantadge -> disadvantage
  typo fixes: aquire -> acquire
  typo fixes: mecanism -> mechanism
  typo fixes: bandwith -> bandwidth
  fix a typo in the RTC_CLASS help text
  smb is no longer maintained

Manually merged trivial conflict in arch/um/kernel/vmlinux.lds.S
2006-06-30 15:39:30 -07:00
David S. Miller 93872ba21d [SERIAL] sunhv: Convert to of_driver layer.
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-06-30 14:13:38 -07:00
David S. Miller a1d22d3258 [SERIAL] sunsu: Missing return statement in su_probe().
If we have a keyboard/mouse port, don't drop through to
calling sunsu_autoconfig().

Signed-off-by: David S. Miller <davem@davemloft.net>
2006-06-30 14:13:34 -07:00
Dominik Brodowski fec21889cd [PATCH] pcmcia: another ID for serial_cs.c
Add an ID for "GlobeTrotter" cards which need a CIS override

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2006-06-30 22:09:10 +02:00
Jörn Engel 6ab3d5624e Remove obsolete #include <linux/config.h>
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-30 19:25:36 +02:00
Adrian Bunk 80f7228b59 typo fixes: occuring -> occurring
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-30 18:27:16 +02:00
David S. Miller 89d1d0ab4d [SERIAL] sunsab: Fix section mis-match errors.
sunsab_init_one() needs to be __devinit, not __init

Signed-off-by: David S. Miller <davem@davemloft.net>
2006-06-29 16:37:53 -07:00
David S. Miller c4d37215a8 [SERIAL] sunsab: Convert to of_driver framework.
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-06-29 16:37:50 -07:00