Add the device IDs of legacy mode of MCP79 AHCI controller to ahci.c
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Highpoint RocketRAID boards using Marvell 7042 chips
overwrite the 9th sector of attached drives at boot time,
when those drives are configured as "Legacy" (the default)
in the HighPoint BIOS.
This kills GRUB, and probably other stuff.
But it all happens *before* Linux is even loaded.
So, for now we'll log a WARNING when such boards are detected,
and advise users to configure BIOS "JBOD" volumes instead,
which don't appear to suffer from this problem.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We need to run any DMA command with result taskfile requested in ADMA mode
when the port is in ADMA mode, otherwise it may try to use the legacy DMA engine
in ADMA mode which is not allowed. Enforce this with BUG_ON() since data
corruption could potentially result if this happened. Also, fail any attempt to
try and issue NCQ commands with result taskfile requested, since the hardware
doesn't allow this.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Make sure the restore psw masks are initialized.
[S390] Fix compile error on 31bit without preemption
[S390] dcssblk: prevent early access without own make_request function
[S390] cio: add missing reprobe loop end statement
[S390] cio: Issue SenseID per path.
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
sched: default to more agressive yield for SCHED_BATCH tasks
sched: fix crash in sys_sched_rr_get_interval()
I haven't seen Richard doing MTRR related work for quite some time, and
the "X86 ARCHITECTURE" entry in MAINTAINERS already covers the people
currently responsible for this code.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fix this on i386 allnoconfig:
WARNING: vmlinux.o(.text+0x6f2e): Section mismatch: reference to .init.text:register_cpu (between 'arch_register_cpu' and 'text_poke')
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
free_cache_attributes() must be __cpuinit since it calls the
__cpuinit cache_remove_shared_cpu_map().
This patch fixes the following section mismatch reported by
Chris Clayton:
...
WARNING: vmlinux.o(.text+0x90b6): Section mismatch: reference to .init.text:cache_remove_shared_cpu_map (between 'free_cache_attributes' and 'show_level')
...
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Our automated test suite looks for keywords like error, fail, warning in
the boot log. In the case when the nmi watchdog is determined to be
stuck in check_nmi_watchdog(), none of those keywords are displayed.
This patch adds a keyword, "WARNING:", so it makes it easier to notice
when the nmi watchdog isn't working correctly. Also add a proper
KERN_WARNING mark to this printout.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The recent Kconfig changes in x86 resulted in CONFIG_X86_HT no longer
being set if (X86_32 && MK8).
After grep'ing through the tree I think the problem is that different
places have different assumptions about the semantics of CONFIG_X86_HT,
either:
- hyperthreading or
- multicore
This should be sorted out properly, but until then we should keep the
2.6.23 status quo.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
do more agressive yield for SCHED_BATCH tuned tasks: they are all
about throughput anyway. This allows a gentler migration path for
any apps that relied on stronger yield.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Luiz Fernando N. Capitulino reported that sched_rr_get_interval()
crashes for SCHED_OTHER tasks that are on an idle runqueue.
The fix is to return a 0 timeslice for tasks that are on an idle
runqueue. (and which are not running, obviously)
this also shrinks the code a bit:
text data bss dec hex filename
47903 3934 336 52173 cbcd sched.o.before
47885 3934 336 52155 cbbb sched.o.after
Reported-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In case of TRACE_IRQFLAGS the restore psw masks will not be
initialized if noexec is turned on. This will lead to an
immediate system crash.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Commit b8e7a54cd0 introduced a compile
error if CONFIG_PREEMPT is not set:
arch/s390/kernel/built-in.o: In function `cleanup_io_leave_insn':
/space/kvm/arch/s390/kernel/entry.S:(.text+0xbfce): undefined reference to `preempt_schedule_irq'
This patch hides preempt_schedule_irq if CONFIG_PREEMPT is not set.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When loading a dcss segment with the dcssblk driver, sometimes the
following kind of message appears:
bio too big device dcssblk0 (8 > 0)
Buffer I/O error on device dcssblk0, logical block 172016
..
The fix is to move the disk registration after setting the
make_request function, to avoid calls into generic_make_request
for dcssblock without having the make_request function set up
properly.
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add loop end statement to prevent looping over empty subchannel sets.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We may receive a unit check for every path when we issue a SenseID.
Unfortunately, the channel subsystem will try on a different path
every time if we use a lpm of 0xff, which will exhaust our retry
counter.
Therefore, revert SenseID to its previous per-path behaviour and
just leave out the suspend multipath reconnect.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.24:
sh: Support PCI IO access of SH7780 base boards.
sh: Fix PCI IO space base address of SH7780.
The old code did did only work as long as CFE and the kernel were using
the same interrupt numbering ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Remove xmon from ml300 and ml403 defconfig in arch/ppc
Revert "[POWERPC] Fix RTAS os-term usage on kernel panic"
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPICA: fix acpi-cpufreq boot crash due to _PSD return-by-reference
ACPI: Delete the IRQ operation in throttling controll via PTC
pageexec@freemail.hu writes:
> i've just noticed that the chunk in i386/kernel/head.S ended up in a
> weird place, namely, it's not going to be executed as it's just after
> a 'jmp 3f' and before startup_32_smp, probably not what you intended.
> on a sidenote, the whole thing can be done in a single insn, like:
>
> movl $(swapper_pg_pmd - __PAGE_OFFSET + 0x067), (swapper_pg_dir -
> __PAGE_OFFSET+ 4092)
Thanks for the reminder I thought we had fixed this problem a while ago.
Needed to get fixed virtual address for USB debug and earlycon with mmio.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
we should also add hpet_disable() for kdump.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If HPET was enabled by pci quirks, we use i8253 as initial clockevent
because pci quirks doesn't run until pci is initialized.
The above means the kernel (or something) is assuming HPET legacy
replacement is disabled and can use i8253 at boot.
If we used kexec, it isn't true. So, this patch disables HPET legacy
replacement for kexec in machine_shutdown().
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/net-2.6: (27 commits)
[INET]: Fix inet_diag dead-lock regression
[NETNS]: Fix /proc/net breakage
[TEXTSEARCH]: Do not allow zero length patterns in the textsearch infrastructure
[NETFILTER]: fix forgotten module release in xt_CONNMARK and xt_CONNSECMARK
[NETFILTER]: xt_TCPMSS: remove network triggerable WARN_ON
[DECNET]: dn_nl_deladdr() almost always returns no error
[IPV6]: Restore IPv6 when MTU is big enough
[RXRPC]: Add missing select on CRYPTO
mac80211: rate limit wep decrypt failed messages
rfkill: fix double-mutex-locking
mac80211: drop unencrypted frames if encryption is expected
mac80211: Fix behavior of ieee80211_open and ieee80211_close
ieee80211: fix unaligned access in ieee80211_copy_snap
mac80211: free ifsta->extra_ie and clear IEEE80211_STA_PRIVACY_INVOKED
SCTP: Fix build issues with SCTP AUTH.
SCTP: Fix chunk acceptance when no authenticated chunks were listed.
SCTP: Fix the supported extensions paramter
SCTP: Fix SCTP-AUTH to correctly add HMACS paramter.
SCTP: Fix the number of HB transmissions.
[TCP] illinois: Incorrect beta usage
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (48 commits)
LIB82596: correct data types for hardware addresses
via-velocity: don't oops on MTU change (resend)
Stop phy code from returning success to unknown ioctls.
SET_NETDEV_DEV() in fec_mpc52xx.c
net: smc911x: only enable for mpr2 on sh.
e1000: Fix NAPI state bug when Rx complete
sky2: turn of dynamic Tx watermark workaround (FE+ only)
sky2: don't use AER routines
sky2: revert to access PCI config via device space
cxgb - fix stats
cxgb - fix NAPI
cxgb - fix T2 GSO
ucc_geth: handle passing of RX-only and TX-only internal delay PHY connection type parameters
phylib: marvell: add support for TX-only and RX-only Internal Delay
phylib: add PHY interface modes for internal delay for tx and rx only
skge: MTU changing fix
skge: serial mode register values
skge version 1.13
skge: increase TX threshold for Jumbo
skge: fiber link up/down fix
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: Fix broken Marvell 7042 support.
libata: Fix early use of port printk. (Was Re: ata4294967295: failed to start port (errno=-19))
ata_piix: add more toshiba laptops to broken suspend list
libata: More IVB horkage from TSST
libata: report protocol and full CDB on error
Several fixes for the AVR32 PATA driver
sata_mv: fix compilation error when enabling DEBUG
Set proper ATA UDMA mode for bf548 according to system clock.
Under the conditions that UML uses it, tcgetattr is guaranteed to return
-EINTR when the console is attached to /dev/ptmx, making generic_console_write
hang because it loops, calling tcgetattr until it succeeds. This is a host
bug - see http://marc.info/?l=linux-kernel&m=119618990807182&w=2 for the
details.
This patch works around it by blocking SIGIO while the terminal attributes are
being fiddled.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I forgot to have an int-returning function actually return something.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous commit ("uml: keep UML Kconfig in sync with x86") is not
enough, unfortunately. If we go that way, we need to add dependencies
on !UML for several options.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a UML build breakage introduced by commit
1032c0ba9d - it introduces X86_32, with many
things which UML needs depending on it.
This patch adds definitions of X86_32 and RWSEM_XCHGADD_ALGORITHM to
the UML/i386 Kconfig.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The inet_diag register fix broke inet_diag module loading because the
loaded module had to take the same mutex that's already held by the
loader in order to register the new handler.
This patch fixes it by introducing a separate mutex to protect the
handling of handlers.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
xmon is broken under arch/ppc so remove it from the defconfig.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit a2b51812a4.
It turns out that this change caused some machines to fail to come
back up when being rebooted, and generated an error in the hypervisor
error log on some machines. The platform architecture (PAPR) is a
little unclear on exactly when the RTAS ibm,os-term function should be
called. Until that is clarified I'm reverting this commit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Changed resolution of named references in packages
Fixed a problem with the Package operator where all named
references were created as object references and left otherwise
unresolved. According to the ACPI specification, a Package can
only contain Data Objects or references to control methods. The
implication is that named references to Data Objects (Integer,
Buffer, String, Package, BufferField, Field) should be resolved
immediately upon package creation. This is the approach taken
with this change. References to all other named objects (Methods,
Devices, Scopes, etc.) are all now properly created as reference objects.
http://bugzilla.kernel.org/show_bug.cgi?id=5328http://bugzilla.kernel.org/show_bug.cgi?id=9429
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit cfb5285660 removed a useful feature for
us, which provided a cpu accounting resource controller. This feature would be
useful if someone wants to group tasks only for accounting purpose and doesnt
really want to exercise any control over their cpu consumption.
The patch below reintroduces the feature. It is based on Paul Menage's
original patch (Commit 62d0df6406), with
these differences:
- Removed load average information. I felt it needs more thought (esp
to deal with SMP and virtualized platforms) and can be added for
2.6.25 after more discussions.
- Convert group cpu usage to be nanosecond accurate (as rest of the cfs
stats are) and invoke cpuacct_charge() from the respective scheduler
classes
- Make accounting scalable on SMP systems by splitting the usage
counter to be per-cpu
- Move the code from kernel/cpu_acct.c to kernel/sched.c (since the
code is not big enough to warrant a new file and also this rightly
needs to live inside the scheduler. Also things like accessing
rq->lock while reading cpu usage becomes easier if the code lived in
kernel/sched.c)
The patch also modifies the cpu controller not to provide the same accounting
information.
Tested-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Tested the patches on top of 2.6.24-rc3. The patches work fine. Ran
some simple tests like cpuspin (spin on the cpu), ran several tasks in
the same group and timed them. Compared their time stamps with
cpuacct.usage.
Signed-off-by: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The IRQ operation(enable/disable) should be avoided when throttling is
controlled via PTC method. It is replaced by the migration of task.
This fixes an oops on T61 -- a regression due to
f79f06ab9f b/c FixedHW support tried to read remote MSR with interrupts disabled.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
sata_mv: Fix broken Marvell 7042 support.
The Marvell 7042 chip is more or less the same as the 6042 internally,
but sports a PCIe bus. Despite having identical SATA cores, the 7042
does differ from its PCI bus counterparts in placment and layout of
certain bus related registers.
This patch fixes sata_mv to distinguish between the PCI bus registers
of earlier chips, and the PCIe bus registers of the 7042.
Specifically, move the offsets and bit patterns for the
PCI/PCIe interrupt cause/mask registers into the struct mv_host_priv,
as these values differ between the 6xxx and 7xxx series chips.
This fixes the driver to not access reserved PCI addresses,
and prevents the lockups reported in linux-2.6.24 with 7042 boards.
Also add a new PCI ID for the Highpoint 2300 7042-based board
that I'm using for testing this stuff here.
Tested with Marvell 6081 + 7042 chips, on x86 & x86_64.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Fri, 30 Nov 2007 14:34:11 +0200 (EET)
Meelis Roos <mroos@linux.ee> wrote:
> > Can you stick a stack trace in at that point ? That would help diagnose
> > it a great deal quicker.
>
> Finally done - found out hard way that BUG() is too bad and
> dump_st5ack() suits me better.
Thanks. This should fix the real cause, and also allow for port start to
fail politely with -ENODEV.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add more toshiba laptops to broken suspend list. This is from OSDL
bugzilla bug 7780.
tj: re-formatted patch and added description and SOB.
Signed-off-by: Peter Schwenke <peter@bluetoad.com.au>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
