[ Upstream commit 581e2b4197 ]
Fix issues with DMA transfers bigger than 512 bytes on Exynos3250. Without
the patches such transfers fail to complete. This solution to the problem
is found in the vendor kernel for ARTIK5 boards based on Exynos3250.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-2-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b867eef4cf ]
The SPIE register contains counts for the TX FIFO so any time the irq
handler was invoked we would attempt to process the RX/TX fifos. Use the
SPIM value to mask the events so that we only process interrupts that
were expected.
This was a latent issue exposed by commit 3282a3da25 ("powerpc/64:
Implement soft interrupt replay in C").
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200904002812.7300-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b59a7ca154 ]
In the prepare_message callback the bus driver has the
opportunity to split a transfer into smaller chunks.
spi_map_msg is done after prepare_message.
Function spi_res_release releases the splited transfers
in the message. Therefore spi_res_release should be called
after spi_map_msg.
The previous try at this was commit c9ba7a16d0
which released the splited transfers after
spi_finalize_current_message had been called.
This introduced a race since the message struct could be
out of scope because the spi_sync call got completed.
Fixes this leak on spi bus driver spi-bcm2835.c when transfer
size is greater than 65532:
Kmemleak:
sg_alloc_table+0x28/0xc8
spi_map_buf+0xa4/0x300
__spi_pump_messages+0x370/0x748
__spi_sync+0x1d4/0x270
spi_sync+0x34/0x58
spi_test_execute_msg+0x60/0x340 [spi_loopback_test]
spi_test_run_iter+0x548/0x578 [spi_loopback_test]
spi_test_run_test+0x94/0x140 [spi_loopback_test]
spi_test_run_tests+0x150/0x180 [spi_loopback_test]
spi_loopback_test_probe+0x50/0xd0 [spi_loopback_test]
spi_drv_probe+0x84/0xe0
Signed-off-by: Gustav Wiklander <gustavwi@axis.com>
Link: https://lore.kernel.org/r/20200908151129.15915-1-gustav.wiklander@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 837ba18dfc ]
The "tx/rx-transfer - crossing PAGE_SIZE" test always fails when
len=131071 and rx_offset >= 5:
spi-loopback-test spi0.0: Running test tx/rx-transfer - crossing PAGE_SIZE
...
with iteration values: len = 131071, tx_off = 0, rx_off = 3
with iteration values: len = 131071, tx_off = 0, rx_off = 4
with iteration values: len = 131071, tx_off = 0, rx_off = 5
loopback strangeness - rx changed outside of allowed range at: ...a4321000
spi_msg@ffffffd5a4157690
frame_length: 131071
actual_length: 131071
spi_transfer@ffffffd5a41576f8
len: 131071
tx_buf: ffffffd5a4340ffc
Note that rx_offset > 3 can only occur if the SPI controller driver sets
->dma_alignment to a higher value than 4, so most SPI controller drivers
are not affect.
The allocated Rx buffer is of size SPI_TEST_MAX_SIZE_PLUS, which is 132
KiB (assuming 4 KiB pages). This test uses an initial offset into the
rx_buf of PAGE_SIZE - 4, and a len of 131071, so the range expected to
be written in this transfer ends at (4096 - 4) + 5 + 131071 == 132 KiB,
which is also the end of the allocated buffer. But the code which
verifies the content of the buffer reads a byte beyond the allocated
buffer and spuriously fails because this out-of-bounds read doesn't
return the expected value.
Fix this by using ITERATE_LEN instead of ITERATE_MAX_LEN to avoid
testing sizes which cause out-of-bounds reads.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20200902132341.7079-1-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c170a5a3b6 ]
The pm_runtime_get_sync() can return either 0 or 1 on success but this
code treats 1 as a failure.
Fixes: db96bf976a ("spi: stm32: fixes suspend/resume management")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alain Volmat <alain.volmat@st.com>
Link: https://lore.kernel.org/r/20200909094304.GA420136@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea8be08cc9 ]
The 'spi_stm32 44004000.spi: Communication suspended' message means that
when using PIO, the kernel did not read the FIFO fast enough and so the
SPI controller paused the transfer. Currently, this is printed on every
single such event, so if the kernel is busy and the controller is pausing
the transfers often, the kernel will be all the more busy scrolling this
message into the log buffer every few milliseconds. That is not helpful.
Instead, rate-limit the message and print it every once in a while. It is
not possible to use the default dev_warn_ratelimited(), because that is
still too verbose, as it prints 10 lines (DEFAULT_RATELIMIT_BURST) every
5 seconds (DEFAULT_RATELIMIT_INTERVAL). The policy here is to print 1 line
every 50 seconds (DEFAULT_RATELIMIT_INTERVAL * 10), because 1 line is more
than enough and the cycles saved on printing are better left to the CPU to
handle the SPI. However, dev_warn_once() is also not useful, as the user
should be aware that this condition is possibly recurring or ongoing. Thus
the custom rate-limit policy.
Finally, turn the message from dev_warn() to dev_dbg(), since the system
does not suffer any sort of malfunction if this message appears, it is
just slowing down. This further reduces the printing into the log buffer
and frees the CPU to do useful work.
Fixes: dcbe0d84df ("spi: add driver for STM32 SPI controller")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Antonio Borneo <borneo.antonio@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200905151913.117775-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60ccb3515f ]
SPI registers content may have been lost upon suspend/resume sequence.
So, always compute and apply the necessary configuration in
stm32_spi_transfer_one_setup routine.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Link: https://lore.kernel.org/r/1597043558-29668-6-git-send-email-alain.volmat@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cc61973bf ]
Fix spi->clk_rate when it is odd to the nearest lowest even value because
minimum SPI divider is 2.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Link: https://lore.kernel.org/r/1597043558-29668-4-git-send-email-alain.volmat@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3373e9004a ]
When transfer is shorter than half of the fifo, set the data packet size
up to transfer size instead of up to half of the fifo.
Check also that threshold is set at least to 1 data frame.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Link: https://lore.kernel.org/r/1597043558-29668-3-git-send-email-alain.volmat@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 135dd873d3 ]
The caller of stm32_spi_transfer_one(), spi_transfer_one_message(),
is waiting for us to call spi_finalize_current_transfer() and will
eventually schedule a new transfer, if available.
We should guarantee that the spi controller is really available
before calling spi_finalize_current_transfer().
Move the call to spi_finalize_current_transfer() _after_ the call
to stm32_spi_disable().
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Link: https://lore.kernel.org/r/1597043558-29668-2-git-send-email-alain.volmat@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae1ba50f1e ]
Previously the stm32h7 interrupt thread cleared all non-masked interrupts.
If an interrupt was to occur during the handling of another interrupt its
flag would be unset, resulting in a lost interrupt.
This patches fixes the issue by clearing only the currently set interrupt
flags.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20200804195136.1485392-1-t.schramm@manjaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ddf75be47c upstream.
CONFIG_OF_DYNAMIC and CONFIG_ACPI allow adding SPI devices at runtime
using a DeviceTree overlay or DSDT patch. CONFIG_SPI_SLAVE allows the
same via sysfs.
But there are no precautions to prevent adding a device below a
controller that's being removed. Such a device is unusable and may not
even be able to unbind cleanly as it becomes inaccessible once the
controller has been torn down. E.g. it is then impossible to quiesce
the device's interrupt.
of_spi_notify() and acpi_spi_notify() do hold a ref on the controller,
but otherwise run lockless against spi_unregister_controller().
Fix by holding the spi_add_lock in spi_unregister_controller() and
bailing out of spi_add_device() if the controller has been unregistered
concurrently.
Fixes: ce79d54ae4 ("spi/of: Add OF notifier handler")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.19+
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Link: https://lore.kernel.org/r/a8c3205088a969dc8410eec1eba9aface60f36af.1596451035.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa9e862d7d upstream.
Simply copying all xfers from userspace into one bounce buffer causes
alignment problems if the SPI controller uses DMA.
Ensure that all transfer data blocks within the rx and tx bounce buffers
are aligned for DMA (according to ARCH_KMALLOC_MINALIGN).
Alignment may increase the usage of the bounce buffers. In some cases,
the buffers may need to be increased using the "bufsiz" module
parameter.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200728100832.24788-1-ceggers@arri.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ba3548cf29 ]
The lantiq-ssc driver uses internally an own workqueue to wait till the
data is not only written out of the FIFO but really written to the wire.
This workqueue is flushed while the SPI subsystem is working in some
other system workqueue.
The system workqueue is marked as WQ_MEM_RECLAIM, but the workqueue in
the lantiq-ssc driver does not use WQ_MEM_RECLAIM for now. Add this flag
too to prevent this warning.
This fixes the following warning:
[ 2.975956] WARNING: CPU: 1 PID: 17 at kernel/workqueue.c:2614 check_flush_dependency+0x168/0x184
[ 2.984752] workqueue: WQ_MEM_RECLAIM kblockd:blk_mq_run_work_fn is flushing !WQ_MEM_RECLAIM 1e100800.spi:0x0
Fixes: 891b7c5fbf ("mtd_blkdevs: convert to blk-mq")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://lore.kernel.org/r/20200717215648.20522-1-hauke@hauke-m.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4294e4accf ]
The RXFLR is possible larger than rx_left in Rockchip SPI, fix it.
Fixes: 01b59ce5da ("spi: rockchip: use irq rather than polling")
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20200723004356.6390-3-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8bdd79dae1 upstream.
The watchdog counter consists of WDG_LOAD_LOW and WDG_LOAD_HIGH,
which would be loaded to watchdog counter once writing WDG_LOAD_LOW.
Fixes: ac17750120 ("spi: sprd: Add the support of restarting the system")
Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200602082415.5848-1-zhang.lyra@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ed7815db70 ]
A SPI transfer defines the _maximum_ speed of the SPI transfer. However the
driver doesn't take into account that the clock divider is always rounded down
(due to integer arithmetics). This results in a too high clock rate for the SPI
transfer.
E.g.: with a mclk_rate of 24 MHz and a SPI transfer speed of 10 MHz, the
original code calculates a reg of "0", which results in a effective divider of
"2" and a 12 MHz clock for the SPI transfer.
This patch fixes the issue by using DIV_ROUND_UP() instead of a plain
integer division.
While there simplify the divider calculation for the CDR1 case, use
order_base_2() instead of two ilog2() calculations.
Fixes: 3558fe900e ("spi: sunxi: Add Allwinner A31 SPI controller driver")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-2-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c525b69e8 ]
During shutdown, the driver should unregister the SPI controller
and stop the hardware. Otherwise the dspi_transfer_one_message() could
wait on completion infinitely.
Additionally, calling spi_unregister_controller() first in device
shutdown reverse-matches the probe function, where SPI controller is
registered at the end.
Fixes: dc23482599 ("spi: spi-fsl-dspi: Adding shutdown hook")
Reported-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-2-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06096cc6c5 ]
If an spi device is unbounded from the driver before the release
process, there will be an NULL pointer reference when it's
referenced in spi_slave_abort().
Fix it by checking it's already freed before reference.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Link: https://lore.kernel.org/r/20200618032125.4650-2-zhenzhong.duan@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7684580d45 ]
During device removal, the driver should unregister the SPI controller
and stop the hardware. Otherwise the dspi_transfer_one_message() could
wait on completion infinitely.
Additionally, calling spi_unregister_controller() first in device
removal reverse-matches the probe function, where SPI controller is
registered at the end.
Fixes: 05209f4570 ("spi: fsl-dspi: add missing clk_disable_unprepare() in dspi_remove()")
Reported-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc23482599 ]
We need to ensure dspi controller could be stopped in order for kexec
to start the next kernel.
So add the shutdown operation support.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Link: https://lore.kernel.org/r/20200424061216.27445-1-peng.ma@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3d87b613d6 upstream.
If shared interrupt comes late, during probe error path or device remove
(could be triggered with CONFIG_DEBUG_SHIRQ), the interrupt handler
dspi_interrupt() will access registers with the clock being disabled.
This leads to external abort on non-linefetch on Toradex Colibri VF50
module (with Vybrid VF5xx):
$ echo 4002d000.spi > /sys/devices/platform/soc/40000000.bus/4002d000.spi/driver/unbind
Unhandled fault: external abort on non-linefetch (0x1008) at 0x8887f02c
Internal error: : 1008 [#1] ARM
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
Backtrace:
(regmap_mmio_read32le)
(regmap_mmio_read)
(_regmap_bus_reg_read)
(_regmap_read)
(regmap_read)
(dspi_interrupt)
(free_irq)
(devm_irq_release)
(release_nodes)
(devres_release_all)
(device_release_driver_internal)
The resource-managed framework should not be used for shared interrupt
handling, because the interrupt handler might be called after releasing
other resources and disabling clocks.
Similar bug could happen during suspend - the shared interrupt handler
could be invoked after suspending the device. Each device sharing this
interrupt line should disable the IRQ during suspend so handler will be
invoked only in following cases:
1. None suspended,
2. All devices resumed.
Fixes: 349ad66c0a ("spi:Add Freescale DSPI driver for Vybrid VF610 platform")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-3-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f0410bbf7d ]
DW APB SSI DMA-part of the driver may need to perform the requested
SPI-transfer synchronously. In that case the dma_transfer() callback
will return 0 as a marker of the SPI transfer being finished so the
SPI core doesn't need to wait and may proceed with the SPI message
trasnfers pumping procedure. This will be needed to fix the problem
when DMA transactions are finished, but there is still data left in
the SPI Tx/Rx FIFOs being sent/received. But for now make dma_transfer
to return 1 as the normal dw_spi_transfer_one() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dadde344d ]
By unknown reason the commit 64bee4d28c
("spi / ACPI: add ACPI enumeration support")
missed the DataBitLength property to encounter when parse SPI slave
device data from ACPI.
Fill the gap here.
Fixes: 64bee4d28c ("spi / ACPI: add ACPI enumeration support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200413180406.1826-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46164fde6b ]
Tx-only DMA transfers are working perfectly fine since in this case
the code just ignores the Rx FIFO overflow interrupts. But it turns
out the SPI Rx-only transfers are broken since nothing pushing any
data to the shift registers, so the Rx FIFO is left empty and the
SPI core subsystems just returns a timeout error. Since DW DMAC
driver doesn't support something like cyclic write operations of
a single byte to a device register, the only way to support the
Rx-only SPI transfers is to fake it by using a dummy Tx-buffer.
This is what we intend to fix in this commit by setting the
SPI_CONTROLLER_MUST_TX flag for DMA-capable platform.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-9-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43dba9f3f9 ]
It's pointless to track the Tx overrun interrupts if Rx-only SPI
transfer is issued. Similarly there is no need in handling the Rx
overrun/underrun interrupts if Tx-only SPI transfer is executed.
So lets unmask the interrupts only if corresponding SPI
transactions are implied.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200522000806.7381-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cb97e223d ]
Some DMA controller drivers do not tolerate non-zero values in
the DMA configuration structures. Zero them to avoid issues with
such DMA controller drivers. Even despite above this is a good
practice per se.
Fixes: 7063c0d942 ("spi/dw_spi: add DMA support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Feng Tang <feng.tang@intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6eefaee4f2 ]
With a couple allies at Intel, and much badgering, I got confirmation
from Intel that at least BXT suffers from the same SPI chip-select
issue as Cannonlake (and beyond). The issue being that after going
through runtime suspend/resume, toggling the chip-select line without
also sending data does nothing.
Add the quirk to BXT to briefly toggle dynamic clock gating off and
on, forcing the fabric to wake up enough to notice the CS register
change.
Signed-off-by: Evan Green <evgreen@chromium.org>
Cc: Shobhit Srivastava <shobhit.srivastava@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200427163238.1.Ib1faaabe236e37ea73be9b8dcc6aa034cb3c8804@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80300a7d5f ]
Currently buswidths 2 and 4 are rejected for a device that advertises
Octal capabilities. Allow these buswidths, just like is done for
buswidth 2 and Quad-capable devices.
Fixes: b12a084c87 ("spi: spi-mem: add support for octal mode I/O data transfer")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200416101418.14379-1-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4df3bea7f9 upstream.
Currently we set the tx/rx buffer to 0xff when NULL. This causes
problems with some spi slaves where 0xff is a valid command. Looking
at other drivers, the tx/rx buffer is usually set to 0x00 when NULL.
Following this convention solves the issue.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200420190853.45614-6-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0392727c26 upstream.
The clock provider may not be ready by the time spi-bcm-qspi gets
probed, handle probe deferral using devm_clk_get_optional().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200420190853.45614-2-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9dd3f6d41 upstream.
The BCM2835aux SPI driver uses devm_spi_register_master() on bind.
As a consequence, on unbind, __device_release_driver() first invokes
bcm2835aux_spi_remove() before unregistering the SPI controller via
devres_release_all().
This order is incorrect: bcm2835aux_spi_remove() turns off the SPI
controller, including its interrupts and clock. The SPI controller
is thus no longer usable.
When the SPI controller is subsequently unregistered, it unbinds all
its slave devices. If their drivers need to access the SPI bus,
e.g. to quiesce their interrupts, unbinding will fail.
As a rule, devm_spi_register_master() must not be used if the
->remove() hook performs teardown steps which shall be performed
after unbinding of slaves.
Fix by using the non-devm variant spi_register_master(). Note that the
struct spi_master as well as the driver-private data are not freed until
after bcm2835aux_spi_remove() has finished, so accessing them is safe.
Fixes: 1ea29b39f4 ("spi: bcm2835aux: add bcm2835 auxiliary spi device driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.4+
Cc: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/32f27f4d8242e4d75f9a53f7e8f1f77483b08669.1589557526.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9dd277ff92 upstream.
The BCM2835 SPI driver uses devm_spi_register_controller() on bind.
As a consequence, on unbind, __device_release_driver() first invokes
bcm2835_spi_remove() before unregistering the SPI controller via
devres_release_all().
This order is incorrect: bcm2835_spi_remove() tears down the DMA
channels and turns off the SPI controller, including its interrupts
and clock. The SPI controller is thus no longer usable.
When the SPI controller is subsequently unregistered, it unbinds all
its slave devices. If their drivers need to access the SPI bus,
e.g. to quiesce their interrupts, unbinding will fail.
As a rule, devm_spi_register_controller() must not be used if the
->remove() hook performs teardown steps which shall be performed
after unbinding of slaves.
Fix by using the non-devm variant spi_register_controller(). Note that
the struct spi_controller as well as the driver-private data are not
freed until after bcm2835_spi_remove() has finished, so accessing them
is safe.
Fixes: 247263dba2 ("spi: bcm2835: use devm_spi_register_master()")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.13+
Link: https://lore.kernel.org/r/2397dd70cdbe95e0bc4da2b9fca0f31cb94e5aed.1589557526.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65e318e173 upstream.
The PXA2xx SPI driver releases a runtime PM ref in the probe error path
even though it hasn't acquired a ref earlier.
Apparently commit e2b714afee ("spi: pxa2xx: Disable runtime PM if
controller registration fails") sought to copy-paste the invocation of
pm_runtime_disable() from pxa2xx_spi_remove(), but erroneously copied
the call to pm_runtime_put_noidle() as well. Drop it.
Fixes: e2b714afee ("spi: pxa2xx: Disable runtime PM if controller registration fails")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org # v4.17+
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/58b2ac6942ca1f91aaeeafe512144bc5343e1d84.1590408496.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32e5b57232 upstream.
The PXA2xx SPI driver uses devm_spi_register_controller() on bind.
As a consequence, on unbind, __device_release_driver() first invokes
pxa2xx_spi_remove() before unregistering the SPI controller via
devres_release_all().
This order is incorrect: pxa2xx_spi_remove() disables the chip,
rendering the SPI bus inaccessible even though the SPI controller is
still registered. When the SPI controller is subsequently unregistered,
it unbinds all its slave devices. Because their drivers cannot access
the SPI bus, e.g. to quiesce interrupts, the slave devices may be left
in an improper state.
As a rule, devm_spi_register_controller() must not be used if the
->remove() hook performs teardown steps which shall be performed after
unregistering the controller and specifically after unbinding of slaves.
Fix by reverting to the non-devm variant of spi_register_controller().
An alternative approach would be to use device-managed functions for all
steps in pxa2xx_spi_remove(), e.g. by calling devm_add_action_or_reset()
on probe. However that approach would add more LoC to the driver and
it wouldn't lend itself as well to backporting to stable.
The improper use of devm_spi_register_controller() was introduced in 2013
by commit a807fcd090 ("spi: pxa2xx: use devm_spi_register_master()"),
but all earlier versions of the driver going back to 2006 were likewise
broken because they invoked spi_unregister_master() at the end of
pxa2xx_spi_remove(), rather than at the beginning.
Fixes: e0c9905e87 ("[PATCH] SPI: add PXA2xx SSP SPI Driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org # v2.6.17+
Cc: Tsuchiya Yuto <kitakar@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206403#c1
Link: https://lore.kernel.org/r/834c446b1cf3284d2660f1bee1ebe3e737cd02a9.1590408496.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84855678ad upstream.
When an SPI controller unregisters, it unbinds all its slave devices.
For this, their drivers may need to access the SPI bus, e.g. to quiesce
interrupts.
However since commit ffbbdd2132 ("spi: create a message queueing
infrastructure"), spi_destroy_queue() is executed before unbinding the
slaves. It sets ctlr->running = false, thereby preventing SPI bus
access and causing unbinding of slave devices to fail.
Fix by unbinding slaves before calling spi_destroy_queue().
Fixes: ffbbdd2132 ("spi: create a message queueing infrastructure")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.4+
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/8aaf9d44c153fe233b17bc2dec4eb679898d7e7b.1589557526.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca8b19d61e upstream.
The Designware SPI driver uses devm_spi_register_controller() on bind.
As a consequence, on unbind, __device_release_driver() first invokes
dw_spi_remove_host() before unregistering the SPI controller via
devres_release_all().
This order is incorrect: dw_spi_remove_host() shuts down the chip,
rendering the SPI bus inaccessible even though the SPI controller is
still registered. When the SPI controller is subsequently unregistered,
it unbinds all its slave devices. Because their drivers cannot access
the SPI bus, e.g. to quiesce interrupts, the slave devices may be left
in an improper state.
As a rule, devm_spi_register_controller() must not be used if the
->remove() hook performs teardown steps which shall be performed after
unregistering the controller and specifically after unbinding of slaves.
Fix by reverting to the non-devm variant of spi_register_controller().
An alternative approach would be to use device-managed functions for all
steps in dw_spi_remove_host(), e.g. by calling devm_add_action_or_reset()
on probe. However that approach would add more LoC to the driver and
it wouldn't lend itself as well to backporting to stable.
Fixes: 04f421e7b0 ("spi: dw: use managed resources")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org # v3.14+
Cc: Baruch Siach <baruch@tkos.co.il>
Link: https://lore.kernel.org/r/3fff8cb8ae44a9893840d0688be15bb88c090a14.1590408496.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9aea644ca1 ]
Commit 6e0a32d6f3 ("spi: dw: Fix default polarity of native
chipselect") attempted to fix the problem when GPIO active-high
chip-select is utilized to communicate with some SPI slave. It fixed
the problem, but broke the normal native CS support. At the same time
the reversion commit ada9e3fcc1 ("spi: dw: Correct handling of native
chipselect") didn't solve the problem either, since it just inverted
the set_cs() polarity perception without taking into account that
CS-high might be applicable. Here is what is done to finally fix the
problem.
DW SPI controller demands any native CS being set in order to proceed
with data transfer. So in order to activate the SPI communications we
must set any bit in the Slave Select DW SPI controller register no
matter whether the platform requests the GPIO- or native CS. Preferably
it should be the bit corresponding to the SPI slave CS number. But
currently the dw_spi_set_cs() method activates the chip-select
only if the second argument is false. Since the second argument of the
set_cs callback is expected to be a boolean with "is-high" semantics
(actual chip-select pin state value), the bit in the DW SPI Slave
Select register will be set only if SPI core requests the driver
to set the CS in the low state. So this will work for active-low
GPIO-based CS case, and won't work for active-high CS setting
the bit when SPI core actually needs to deactivate the CS.
This commit fixes the problem for all described cases. So no matter
whether an SPI slave needs GPIO- or native-based CS with active-high
or low signal the corresponding bit will be set in SER.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Fixes: ada9e3fcc1 ("spi: dw: Correct handling of native chipselect")
Fixes: 6e0a32d6f3 ("spi: dw: Fix default polarity of native chipselect")
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200515104758.6934-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfda044533 ]
Because of out-of-order execution about some CPU architecture,
In this debug stage we find Completing spi interrupt enable ->
prodrucing TXEI interrupt -> running "interrupt_transfer" function
will prior to set "dw->rx and dws->rx_end" data, so this patch add
memory barrier to enable dw->rx and dw->rx_end to be visible and
solve to send SPI data error.
eg:
it will fix to this following low possibility error in testing environment
which using SPI control to connect TPM Modules
kernel: tpm tpm0: Operation Timed out
kernel: tpm tpm0: tpm_relinquish_locality: : error -1
Signed-off-by: fengsheng <fengsheng5@huawei.com>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Link: https://lore.kernel.org/r/1578019930-55858-1-git-send-email-kong.kongxinwei@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f5ee75ea1 ]
Currently the driver puts the process in interruptible sleep waiting for
the interrupt train to finish transfer to/from the tx_buf and rx_buf.
But exiting the process with ctrl-c may make the kernel panic: the
wait_event_interruptible call will return -ERESTARTSYS, which a proper
driver implementation is perhaps supposed to handle, but nonetheless
this one doesn't, and aborts the transfer altogether.
Actually when the task is interrupted, there is still a high chance that
the dspi_interrupt is still triggering. And if dspi_transfer_one_message
returns execution all the way to the spi_device driver, that can free
the spi_message and spi_transfer structures, leaving the interrupts to
access a freed tx_buf and rx_buf.
hexdump -C /dev/mtd0
00000000 00 75 68 75 0a ff ff ff ff ff ff ff ff ff ff ff
|.uhu............|
00000010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
|................|
*
^C[ 38.495955] fsl-dspi 2120000.spi: Waiting for transfer to complete failed!
[ 38.503097] spi_master spi2: failed to transfer one message from queue
[ 38.509729] Unable to handle kernel paging request at virtual address ffff800095ab3377
[ 38.517676] Mem abort info:
[ 38.520474] ESR = 0x96000045
[ 38.523533] EC = 0x25: DABT (current EL), IL = 32 bits
[ 38.528861] SET = 0, FnV = 0
[ 38.531921] EA = 0, S1PTW = 0
[ 38.535067] Data abort info:
[ 38.537952] ISV = 0, ISS = 0x00000045
[ 38.541797] CM = 0, WnR = 1
[ 38.544771] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000082621000
[ 38.551494] [ffff800095ab3377] pgd=00000020fffff003, p4d=00000020fffff003, pud=0000000000000000
[ 38.560229] Internal error: Oops: 96000045 [#1] PREEMPT SMP
[ 38.565819] Modules linked in:
[ 38.568882] CPU: 0 PID: 2729 Comm: hexdump Not tainted 5.6.0-rc4-next-20200306-00052-gd8730cdc8a0b-dirty #193
[ 38.578834] Hardware name: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier (DT)
[ 38.587129] pstate: 20000085 (nzCv daIf -PAN -UAO)
[ 38.591941] pc : ktime_get_real_ts64+0x3c/0x110
[ 38.596487] lr : spi_take_timestamp_pre+0x40/0x90
[ 38.601203] sp : ffff800010003d90
[ 38.604525] x29: ffff800010003d90 x28: ffff80001200e000
[ 38.609854] x27: ffff800011da9000 x26: ffff002079c40400
[ 38.615184] x25: ffff8000117fe018 x24: ffff800011daa1a0
[ 38.620513] x23: ffff800015ab3860 x22: ffff800095ab3377
[ 38.625841] x21: 000000000000146e x20: ffff8000120c3000
[ 38.631170] x19: ffff0020795f6e80 x18: ffff800011da9948
[ 38.636498] x17: 0000000000000000 x16: 0000000000000000
[ 38.641826] x15: ffff800095ab3377 x14: 0720072007200720
[ 38.647155] x13: 0720072007200765 x12: 0775076507750771
[ 38.652483] x11: 0720076d076f0772 x10: 0000000000000040
[ 38.657812] x9 : ffff8000108e2100 x8 : ffff800011dcabe8
[ 38.663139] x7 : 0000000000000000 x6 : ffff800015ab3a60
[ 38.668468] x5 : 0000000007200720 x4 : ffff800095ab3377
[ 38.673796] x3 : 0000000000000000 x2 : 0000000000000ab0
[ 38.679125] x1 : ffff800011daa000 x0 : 0000000000000026
[ 38.684454] Call trace:
[ 38.686905] ktime_get_real_ts64+0x3c/0x110
[ 38.691100] spi_take_timestamp_pre+0x40/0x90
[ 38.695470] dspi_fifo_write+0x58/0x2c0
[ 38.699315] dspi_interrupt+0xbc/0xd0
[ 38.702987] __handle_irq_event_percpu+0x78/0x2c0
[ 38.707706] handle_irq_event_percpu+0x3c/0x90
[ 38.712161] handle_irq_event+0x4c/0xd0
[ 38.716008] handle_fasteoi_irq+0xbc/0x170
[ 38.720115] generic_handle_irq+0x2c/0x40
[ 38.724135] __handle_domain_irq+0x68/0xc0
[ 38.728243] gic_handle_irq+0xc8/0x160
[ 38.732000] el1_irq+0xb8/0x180
[ 38.735149] spi_nor_spimem_read_data+0xe0/0x140
[ 38.739779] spi_nor_read+0xc4/0x120
[ 38.743364] mtd_read_oob+0xa8/0xc0
[ 38.746860] mtd_read+0x4c/0x80
[ 38.750007] mtdchar_read+0x108/0x2a0
[ 38.753679] __vfs_read+0x20/0x50
[ 38.757002] vfs_read+0xa4/0x190
[ 38.760237] ksys_read+0x6c/0xf0
[ 38.763471] __arm64_sys_read+0x20/0x30
[ 38.767319] el0_svc_common.constprop.3+0x90/0x160
[ 38.772125] do_el0_svc+0x28/0x90
[ 38.775449] el0_sync_handler+0x118/0x190
[ 38.779468] el0_sync+0x140/0x180
[ 38.782793] Code: 91000294 1400000f d50339bf f9405e80 (f90002c0)
[ 38.788910] ---[ end trace 55da560db4d6bef7 ]---
[ 38.793540] Kernel panic - not syncing: Fatal exception in interrupt
[ 38.799914] SMP: stopping secondary CPUs
[ 38.803849] Kernel Offset: disabled
[ 38.807344] CPU features: 0x10002,20006008
[ 38.811451] Memory Limit: none
[ 38.814513] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---
So it is clear that the "interruptible" part isn't handled correctly.
When the process receives a signal, one could either attempt a clean
abort (which appears to be difficult with this hardware) or just keep
restarting the sleep until the wait queue really completes. But checking
in a loop for -ERESTARTSYS is a bit too complicated for this driver, so
just make the sleep uninterruptible, to avoid all that nonsense.
The wait queue was actually restructured as a completion, after polling
other drivers for the most "popular" approach.
Fixes: 349ad66c0a ("spi:Add Freescale DSPI driver for Vybrid VF610 platform")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200318001603.9650-7-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9981d4f50 ]
Some error paths leave the bus id allocated. As a result the IDR
allocation will fail after a deferred probe. Fix by freeing the bus id
always on error.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Message-Id: <20200304111740.27915-1-aaro.koskinen@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dd8304981 ]
In the public interface for chipselect, there is always an entry
commented as "Dummy generic FIFO entry" pushed down to the fifo right
after the activate/deactivate command. The dummy entry is 0x0,
irregardless if the intention was to activate or deactive the cs. This
causes the cs line to glitch rather than beeing activated in the case
when there was an activate command.
This has been observed on oscilloscope, and have caused problems for at
least one specific flash device type connected to the qspi port. After
the change the glitch is gone and cs goes active when intended.
The reason why this worked before (except for the glitch) was because
when sending the actual data, the CS bits are once again set. Since
most flashes uses mode 0, there is always a half clk period anyway for
cs to clk active setup time. If someone would rely on timing from a
chip_select call to a transfer_one, it would fail though.
It is unknown why the dummy entry was there in the first place, git log
seems to be of no help in this case. The reference manual gives no
indication of the necessity of this. In fact the lower 8 bits are a
setup (or hold in case of deactivate) time expressed in cycles. So this
should not be needed to fulfill any setup/hold timings.
Signed-off-by: Thommy Jakobsson <thommyj@gmail.com>
Reviewed-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Link: https://lore.kernel.org/r/20200224162643.29102-1-thommyj@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 683f65ded6 ]
In some circumstances on Intel LPSS controllers, toggling the LPSS
CS control register doesn't actually cause the CS line to toggle.
This seems to be failure of dynamic clock gating that occurs after
going through a suspend/resume transition, where the controller
is sent through a reset transition. This ruins SPI transactions
that either rely on delay_usecs, or toggle the CS line without
sending data.
Whenever CS is toggled, momentarily set the clock gating register
to "Force On" to poke the controller into acting on CS.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20200211223700.110252-1-rajatja@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 136b5cd2e2 ]
spi_qup_suspend() will cause synchronous external abort when
runtime suspend is enabled and applied, as it tries to
access SPI controller register while clock is already disabled
in spi_qup_pm_suspend_runtime().
Signed-off-by: Yuji sasaki <sasakiy@chromium.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200214074340.2286170-1-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32f2fc5dc3 ]
dma_request_channel() can return -EPROBE_DEFER, if DMA driver is not
ready. Currently driver just falls back to PIO mode on probe deferral.
Fix this by requesting all required channels during probe and
propagating EPROBE_DEFER error code.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200204124816.16735-3-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
