Add some more chip IDs to bcma_pmu_get_alp_clock()
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hard coding these values use the existing constants.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Synchronize with 'net' in order to sort out some l2tp, wireless, and
ipv6 GRE fixes that will be built on top of in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/ethtool.c
drivers/net/vmxnet3/vmxnet3_drv.c
drivers/net/wireless/iwlwifi/dvm/tx.c
net/ipv6/route.c
The ipv6 route.c conflict is simple, just ignore the 'net' side change
as we fixed the same problem in 'net-next' by eliminating cached
neighbours from ipv6 routes.
The e1000e conflict is an addition of a new statistic in the ethtool
code, trivial.
The vmxnet3 conflict is about one change in 'net' removing a guarding
conditional, whilst in 'net-next' we had a netdev_info() conversion.
The iwlwifi conflict is dealing with a WARN_ON() conversion in
'net-next' vs. a revert happening in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch unregisters the gpio chip before bcma gets unloaded.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old bcm47xx gpio code had support for gpio_to_irq, but the new
code did not provide this function, but returned -ENXIO all the time.
This patch adds the missing function.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
Documentation/networking/ip-sysctl.txt
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
Both conflicts were simply overlapping context.
A build fix for qlcnic is in here too, simply removing the added
devinit annotations which no longer exist.
Signed-off-by: David S. Miller <davem@davemloft.net>
The sanity checks allow 1 and 2 byte reads/writes of the extended
PCI config space to proceed; however, the code only supports 4
byte reads/writes. This patch adds support for 1 and 2 byte
reads/writes of the extended PCI config space.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For PCI config space access offsets < 256 for device '0',
bcma_extpci_write_config performs an 'ioremap_nocache' on a 4 byte
section of the PCI config space (an area that has already
previously been mapped), and then subsequently unmaps that 4 byte
section. This can't be a good thing for future read access from
that now unmapped location. Modify the config space writes to use
the existing access functions (similar to how it is done for the reads).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Consistently jump to the 'out' label for error conditions (adds
missing check for 'func' validity in bcma_extpci_write_config).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'val' has already been read by the prior call to 'mips_busprobe32';
this 'readl' is unnecessary.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default irqflag assignment for the I2S core on some Broadcom
4716/4748 devices is invalid and needs to be corrected (from the
Broadcom SDK).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the PCI configuration for BCM4706 and BCM4716 per the 2011
Broadcom SDK.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The irq signal numbers that are send by the cpu are increased by 2 from
the number programmed into the mips core by bcma.
Return the irq number on which the irqs are send in bcma_core_irq() now.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This error was introduced in:
commit e3f05a42fa
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Fri Jan 4 00:51:21 2013 +0100
bcma: mips: explicit assign IRQ numbers
CC drivers/bcma/driver_mips.o
drivers/bcma/driver_mips.c: In function 'bcma_core_mips_init':
drivers/bcma/driver_mips.c:302:4: error: implicit declaration of
function 'bcma_core_irq' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[6]: *** [drivers/bcma/driver_mips.o] Error 1
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BCMA is a Broadcom specific bus with devices AKA cores. All recent BCMA
based SoCs have gigabit ethernet provided by the GBit MAC core. This
patch adds driver for such a cores registering itself as a netdev. It
has been tested on a BCM4706 and BCM4718 chipsets.
In the kernel tree there is already b44 driver which has some common
things with bgmac, however there are many differences that has led to
the decision or writing a new driver:
1) GBit MAC cores appear on BCMA bus (not SSB as in case of b44)
2) There is 64bit DMA engine which differs from 32bit one
3) There is no CAM (Content Addressable Memory) in GBit MAC
4) We have 4 TX queues on GBit MAC devices (instead of 1)
5) Many registers have different addresses/values
6) RX header flags are also different
The driver in it's state is functional how, however there is of course
place for improvements:
1) Supporting more net_device_ops
2) SUpporting more ethtool_ops
3) Unaligned addressing in DMA
4) Writing separated PHY driver
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) New sysctl ndisc_notify needs some documentation, from Hanns
Frederic Sowa.
2) Netfilter REJECT target doesn't set transport header of SKB
correctly, from Mukund Jampala.
3) Forcedeth driver needs to check for DMA mapping failures, from Larry
Finger.
4) brcmsmac driver can't use usleep_range while holding locks, use
udelay instead. From Niels Ole Salscheider.
5) Fix unregister of netlink bridge multicast database handlers, from
Vlad Yasevich and Rami Rosen.
6) Fix checksum calculations in netfilter's ipv6 network prefix
translation module.
7) Fix high order page allocation failures in netfilter xt_recent, from
Eric Dumazet.
8) mac802154 needs to use netif_rx_ni() instead of netif_rx() because
mac802154_process_data() can execute in process rather than
interrupt context. From Alexander Aring.
9) Fix splice handling of MSG_SENDPAGE_NOTLAST, otherwise we elide one
tcp_push() too many. From Eric Dumazet and Willy Tarreau.
10) Fix skb->truesize tracking in XEN netfront driver, from Ian
Campbell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
xen/netfront: improve truesize tracking
ipv4: fix NULL checking in devinet_ioctl()
tcp: fix MSG_SENDPAGE_NOTLAST logic
net/ipv4/ipconfig: really display the BOOTP/DHCP server's address.
ip-sysctl: fix spelling errors
mac802154: fix NOHZ local_softirq_pending 08 warning
ipv6: document ndisc_notify in networking/ip-sysctl.txt
ath9k: Fix Kconfig for ATH9K_HTC
netfilter: xt_recent: avoid high order page allocations
netfilter: fix missing dependencies for the NOTRACK target
netfilter: ip6t_NPT: fix IPv6 NTP checksum calculation
bridge: add empty br_mdb_init() and br_mdb_uninit() definitions.
vxlan: allow live mac address change
bridge: Correctly unregister MDB rtnetlink handlers
brcmfmac: fix parsing rsn ie for ap mode.
brcmsmac: add copyright information for Canonical
rtlwifi: rtl8723ae: Fix warning for unchecked pci_map_single() call
rtlwifi: rtl8192se: Fix warning for unchecked pci_map_single() call
rtlwifi: rtl8192de: Fix warning for unchecked pci_map_single() call
rtlwifi: rtl8192ce: Fix warning for unchecked pci_map_single() call
...
The new name better matches the use of this variable.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some cores do not have a IRQ assigned and some do not support when an
IRQ is assigned to them, this is now handled and printed out in the
code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The assignment of the IRQs to the cores of the chips by iterating over
the cores is complicated and causes problems with SoC like the BCM4706
with two GMAC core where just one should get a dedicated IRQ number.
Now the code assigns the same IRQs to the cores as the code from the
Broadcom SDK does. If the SoC is not know the current assigned IRQs are
only read out and an error message is printed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This bcma_find_core_unit() is needed by the mips driver in the next
patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, and __devexit
from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: "Rafał Miłecki" <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cf0936b06d ("bcma: add GPIO driver")
added BCMA_DRIVER_GPIO, which unconditionally selects GPIOLIB, causing
a Kconfig warning:
warning: (ARCH_REQUIRE_GPIOLIB && SSB_DRIVER_GPIO && BCMA_DRIVER_GPIO && MFD_TC6393XB && FB_VIA) selects GPIOLIB which has unmet direct dependencies (ARCH_WANT_OPTIONAL_GPIOLIB || ARCH_REQUIRE_GPIOLIB)
and build failure for m68k/allmodconfig:
In file included from include/linux/bcma/bcma.h:8,
from drivers/bcma/bcma_private.h:9,
from drivers/bcma/main.c:9:
include/linux/bcma/bcma_driver_chipcommon.h:582: error: field ‘gpio’ has incomplete type
In file included from include/linux/bcma/bcma.h:12,
from drivers/bcma/bcma_private.h:9,
from drivers/bcma/main.c:9:
include/linux/ssb/ssb.h:440: error: field ‘gpio’ has incomplete type
make[4]: *** [drivers/bcma/main.o] Error 1
make[3]: *** [drivers/bcma/] Error 2
Turn the select into a dependency to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlDSAa4ACgkQdwG7hYl686MMcACeNYa//ghPtccb5L+IRXsqaFDL
Yi4AoLWOaOjN8qM4KUF/bfMEkwNGAePz
=DaAQ
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd
Pull MTD updates from David Woodhouse:
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
* tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd: (96 commits)
mtd: nand: typo in nand_id_has_period() comments
mtd: nand/gpio: use io{read,write}*_rep accessors
mtd: block2mtd: throttle writes by calling balance_dirty_pages_ratelimited.
mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems
mtd: nand/docg4: fix and improve read of factory bbt
mtd: nand/docg4: reserve bb marker area in ecclayout
mtd: nand/docg4: add support for writing in reliable mode
mtd: mxc_nand: reorder part_probes to let cmdline override other sources
mtd: mxc_nand: fix unbalanced clk_disable() in error path
mtd: nandsim: Introduce debugfs infrastructure
mtd: physmap_of: error checking to prevent a NULL pointer dereference
mtg: docg3: potential divide by zero in doc_write_oob()
mtd: bcm47xxnflash: writing support
mtd: tests/read: initialize buffer for whole next page
mtd: at91: atmel_nand: return bit flips for the PMECC read_page()
mtd: fix recovery after failed write-buffer operation in cfi_cmdset_0002.c
mtd: nand: onfi need to be probed in 8 bits mode
mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus width
mtd: nand: print flash size during detection
mted: nand_wait_ready timeout fix
...
Pull MIPS updates from Ralf Baechle:
"The MIPS bits for 3.8. This also includes a bunch fixes that were
sitting in the linux-mips.org git tree for a long time. This pull
request contains updates to several OCTEON drivers and the board
support code for BCM47XX, BCM63XX, XLP, XLR, XLS, lantiq, Loongson1B,
updates to the SSB bus support, MIPS kexec code and adds support for
kdump.
When pulling this, there are two expected merge conflicts in
include/linux/bcma/bcma_driver_chipcommon.h which are trivial to
resolve, just remove the conflict markers and keep both alternatives."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (90 commits)
MIPS: PMC-Sierra Yosemite: Remove support.
VIDEO: Newport Fix console crashes
MIPS: wrppmc: Fix build of PCI code.
MIPS: IP22/IP28: Fix build of EISA code.
MIPS: RB532: Fix build of prom code.
MIPS: PowerTV: Fix build.
MIPS: IP27: Correct fucked grammar in ops-bridge.c
MIPS: Highmem: Fix build error if CONFIG_DEBUG_HIGHMEM is disabled
MIPS: Fix potencial corruption
MIPS: Fix for warning from FPU emulation code
MIPS: Handle COP3 Unusable exception as COP1X for FP emulation
MIPS: Fix poweroff failure when HOTPLUG_CPU configured.
MIPS: MT: Fix build with CONFIG_UIDGID_STRICT_TYPE_CHECKS=y
MIPS: Remove unused smvp.h
MIPS/EDAC: Improve OCTEON EDAC support.
MIPS: OCTEON: Add definitions for OCTEON memory contoller registers.
MIPS: OCTEON: Add OCTEON family definitions to octeon-model.h
ata: pata_octeon_cf: Use correct byte order for DMA in when built little-endian.
MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.
MIPS: Remove usage of CEVT_R4K_LIB config option.
...
We were using wrong IRQ number so clearing wasn't working at all.
Depending on a platform this could result in a one device having two
interrupts assigned. On BCM4706 this resulted in all IRQs being broken.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: stable@vger.kernel.org
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Register the watchdog driver to the system if this is a SoC. Using the
watchdog on a non SoC device, like a PCIe card, will make the PCIe
card die when the timeout expired, but starting it again is not
supported by bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The watchdog driver wants to set the watchdog timeout in ms and not in
ticks, which is depending on the SoC type and the clock.
Calculate the number of ticks per millisecond and provide two functions
for the watchdog driver. Also return the ticks or millisecond the timer
was set to in case the provided value was bigger than the max allowed
value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mostly all bcma based devices have a PMU and the PMU watchdog should be
used and not the old one in chip common. This patch also calculates the
maximal number the watchdog could be set to.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For devices without a PMU the alp clock is always 20000000.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the following warning:
CC drivers/bcma/driver_pci_host.o
drivers/bcma/driver_pci_host.c: In function 'bcma_core_pci_fixup_addresses':
drivers/bcma/driver_pci_host.c:555:23: error: ignoring return value of
'pci_assign_resource', declared with attribute warn_unused_result
[-Werror=unused-result]
Reported-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required by NAND flash driver for initializing wait counters.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Register a GPIO driver to access the GPIOs provided by the chip.
The GPIOs of the SoC should always start at 0 and the other GPIOs could
start at a random position. There is just one SoC in a system and when
they start at 0 the number is predictable.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4587
Acked-by: Florian Fainelli <florian@openwrt.org>
Add functions to access the GPIO registers for pullup and pulldown.
These are needed for handling gpio registration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4586
Acked-by: Florian Fainelli <florian@openwrt.org>
The GPIOs are access through some registers in the chip common core.
We need locking around these GPIO accesses, all GPIOs are accessed
through the same registers and parallel writes will cause problems.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4585
Acked-by: Florian Fainelli <florian@openwrt.org>
This will fix warnings like following when CONFIG_PM_SLEEP is not set:
warning: 'xxx_suspend' defined but not used [-Wunused-function]
warning: 'xxx_resume' defined but not used [-Wunused-function]
Because
SET_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn)
Only references the callbacks on CONFIG_PM_SLEEP (instead of CONFIG_PM).
Cc: John W. Linville <linville@tuxdriver.com>
Cc: "Rafał Miłecki" <zajec5@gmail.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before it was tried to initialize the deactivated PCIe core in client
mode, but this causes the SoC to hang. Just do not initialize it at all
and ignore the core it is not working and nothing is connected to it
when the specific bit is set in the boardflags.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BCM4706 has two PCIe host controller on the bcma bus. For PCIe
client mode it is assumed that there is only one PCIe controller so the
PCIe driver, like b43 and brcmsmac are accessing the first PCIe
controller when they want to issue a operation on the host controller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes the PCIe card indicates that it has a sprom somewhere and we
are able to read the memory region, but it is empty and not valid. In
these cases we should try to use the fallback sprom as a last chance.
This is the case for the PCIe cards in my ASUS RT-N66U (BCM4706 + 2
times BCM4331) and I have heard of someone having the same problem with
an other PCIe card connected to an other Broadcom SoC.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some devices which are able to boot from nand flash and other
are using a serial flash for booting. Add a bool to indicate that the
device is booted from that flash chip and not from some other chip also
connected to the SoC. This is needed to find the nvram, as it is stored
on the flash the devices booted from.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PCIe host driver and the chip common initialisation accesses the
sprom struct, but it is not initialized when these functions are run.
Move the sprom parsing up in to do it earlier.
As we need the chip common core rev and some other attributes from the
chip common core, the early initialization is done before accessing the
sprom.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some parts of the initialization for chip common and the pcie core are
accessing the sprom struct, but it is not initialized at that stage.
Just do the necessary thing in the early register on SoCs and not the
complete initialization to read out the nvram from the flash chip.
After it is possible to read out the nvram, the sprom should be parsed
from it and the full initialization of the cores should be run.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When cores are unregistered, entries
need to be removed from cores list in a safe manner.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma_scan_bus allocates a bcma_core for each core found on the bus, but the
memory for cores handled by the bcma driver itself was not being freed when
the bus was unregistered. This patch adds special handling for the PCIE,
MIPS, and GBIT COMMON cores, to ensure that their memory allocation is
freed as well.
Note that this patch doesn't address the memory allocated for the CC core,
as that was corrected in my previous patch "bcma: register cc core driver,
device."
Cc: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Saul St. John <saul.stjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions and structs are not used in an other file and the
prototypes are in no header file, just make them static so the compiler
is able to optimize them better.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit b9562545ef ("bcma: complete workaround for BCMA43224 and
BCM4313") introduced the wrong masks for setting the chip control
registers - the "mask" parameter is inverse.
It should be the mask of bits *not* changed, which is admittedly a bit
non-intuitive.
The incorrect mask not only causes the driver to not work correctly on
the chips affected (eg the BCM43224 on the Macbook Air 4,2) but the
state persists over a soft reset, causing the next boot to not
necessarily see the device correctly.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Arend Van Spriel <arend@broadcom.com>
Cc: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Cc: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This should fix the problem reported by Fengguang:
The coccinelle static checker emits these warnings:
drivers/bcma/scan.c:466:3-9: ERROR: missing iounmap; ioremap on line 451 and execution via conditional on line 465
drivers/bcma/scan.c:540:3-9: ERROR: missing iounmap; ioremap on line 515 and execution via conditional on line 539
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wrong interrupts where assigned to the cores in
bcma_core_mips_init(). This caused at least my serial console not to
response to any input.
This was caused by this patch which changed the order of the cores in
the list:
commit c334e25c9f
Author: Rafał Miłecki <zajec5@gmail.com>
Date: Wed Jul 11 12:37:00 2012 +0200
bcma: add new cores at the end of list
This should be fixed properly later so that the correct interrupt
numbers are assigned to the cores independently from the ordering of
the list. This patch restores the old behavior again. I will look into
the problem more deeply later.
I also changed the order of the list with the cores and their assigned
interrupt number which gets printed to the log. Now they are printed in
the same order like all the other lists of cores and like it was done
before the patch which changed the order.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes order in list more natural and fixes core->core_unit for more
than 2 cores.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
GMAC COMMON core is present on BCM4706 and is used for example to access
board PHYs (PHYs can not be accessed directly using GBIT MAC core).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having bus number printed makes it much easier to anaylze logs on
systems with more buses. For example Netgear WNDR4500 has 3 AMBA buses
in total, which makes standard log really messy.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is needed by brcmsmac. This code is based on code from
the Broadcom SDK.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The list of devices where nothing has to be done in
bcma_pmu_resources_init() and bcma_pmu_workarounds() is longer as all
the SoCs are missing there and some new devices will be added in some
time later. This patch changes the default case to just log on debug
level and also let the other devices which do not need any special
handling into the default case, instead of adding the missing 8 SoC
chip ids.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These functions are doing nothing in the current code.
I do not think we will need these function in the future as the
corresponding functions in the Broadcom SDK are just doing something
useful on chips supported by ssb or fullmac chips.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is based on the Broadcom SDK and brcmsmac.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ID was found on the PCIe wireless card on the board of a Netgear
WNDR3400 using a bcm4716. The device with this ID is identified by b43
as "Broadcom 43224 WLAN".
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is not core id with 0x4329, but at the same place in the open
source part of the Broadcom SDK is a check for some device with the
chip id of 0x4329. The device with a chip id of 0x4329 is a full mac
device, so it will never be supported by bcma, this part is running in
the firmware of the device and not on the host CPU.
This code is wrong and will never be used, so just remove it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chip IDs are used all over bcma and no constants where defined.
This patch adds the constants and makes bcma use them.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is based on a recent version of the Broadcom SDK.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of them are BCM4706 specific AFAWK. Most of them was confirmed on
Netgear WNDR450.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pc could be null if hosttype != BCMA_HOSTTYPE_PCI.
If we are on a device without a pci core this function is called with
pc = null by b43 and brcmsmac. If the host type is PCI we have a pci
core as well and pc can not be null.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MacBook Pro models with BCM4331 wireless have been found to have the ext
PA lines disabled after resuming from S3 without external power attach.
This causes them to be unable to transmit. Add a workaround to ensure
that the ext PA lines are enabled on BCM4331. Also extend all handling
of ext PA line muxing to BCM43431 as is done in the Broadcom SDK.
BugLink: http://bugs.launchpad.net/bugs/925577
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: stable@vger.kernel.org
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull more networking updates from David Miller:
"Ok, everything from here on out will be bug fixes."
1) One final sync of wireless and bluetooth stuff from John Linville.
These changes have all been in his tree for more than a week, and
therefore have had the necessary -next exposure. John was just away
on a trip and didn't have a change to send the pull request until a
day or two ago.
2) Put back some defines in user exposed header file areas that were
removed during the tokenring purge. From Stephen Hemminger and Paul
Gortmaker.
3) A bug fix for UDP hash table allocation got lost in the pile due to
one of those "you got it.. no I've got it.." situations. :-)
From Tim Bird.
4) SKB coalescing in TCP needs to have stricter checks, otherwise we'll
try to coalesce overlapping frags and crash. Fix from Eric Dumazet.
5) RCU routing table lookups can race with free_fib_info(), causing
crashes when we deref the device pointers in the route. Fix by
releasing the net device in the RCU callback. From Yanmin Zhang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (293 commits)
tcp: take care of overlaps in tcp_try_coalesce()
ipv4: fix the rcu race between free_fib_info and ip_route_output_slow
mm: add a low limit to alloc_large_system_hash
ipx: restore token ring define to include/linux/ipx.h
if: restore token ring ARP type to header
xen: do not disable netfront in dom0
phy/micrel: Fix ID of KSZ9021
mISDN: Add X-Tensions USB ISDN TA XC-525
gianfar:don't add FCB length to hard_header_len
Bluetooth: Report proper error number in disconnection
Bluetooth: Create flags for bt_sk()
Bluetooth: report the right security level in getsockopt
Bluetooth: Lock the L2CAP channel when sending
Bluetooth: Restore locking semantics when looking up L2CAP channels
Bluetooth: Fix a redundant and problematic incoming MTU check
Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C
Bluetooth: Fix EIR data generation for mgmt_device_found
Bluetooth: Fix Inquiry with RSSI event mask
Bluetooth: improve readability of l2cap_seq_list code
Bluetooth: Fix skb length calculation
...
Adds a missing read to flush the previous write (per the Broadcom SDK).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add missing __devexit attribute to bcma_host_pci_remove.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify ioremap_nocache calls to reflect the number of bytes read/written.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PCI Memory Resource start address and size are variable, dependent on
the H/W configuration. Modify the computation of io_map_base to use the
computed values.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma_device_name only provides names for Broadcom cores. Modify logic to
provide names for MIPS and ARM cores as well.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is based on code from pcie_misc_config_fixup() in brcmsmac.
This patch is part of the move of pci specific code from brcmsmac to
bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is based on code from pcicore_fixcfg() in brcmsmac. This
patch is part of the move of pci specific code from brcmsmac to bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is based on code from pcie_extendL1timer() in brcmsmac. This
patch is part of the move of pci specific code from brcmsmac to bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is based on code from _ai_clkctl_cc() in brcmsmac.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These newly added attributes are used by brcmsmac. Now bcma should
parse all attributes used by brcmsmac out of the sprom.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is copied from the ssb sprom read code. These attributes are
partly used by b43 and brcmsmac and should also be read out on bcma
based devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The attribute country_code and alpha2 are two different attributes in
the sprom. country_code contains some code in an 8 bit coding and
alpha2 contains two chars with the country code. The attributes where
read out wrongly in the past and country_code is only available on
sprom version 1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This struct contains information about the board, the chip is running
on. The struct is filled for PCIe devices and SoCs. This information is
used by b43 and will be used by brcmsmac soon.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This resolves the conflict in:
drivers/usb/host/ehci-fsl.c
And picks up loads of xhci bugfixes to make it easier for others to test
with.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some cores like the USB core have two address spaces. In the USB host
controller one address space is used for the OHCI and the other for the
EHCI controller interface. The USB controller is the only core I found
with two address spaces. This code is based on the AI scan function
ai_scan() in shared/aiutils.c in the Broadcom SDK.
CC: Rafał Miłecki <zajec5@gmail.com>
CC: linux-wireless@vger.kernel.org
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bcma should check for a fallback sprom every time it can not find a
sprom on the card itself or a normal external sprom mapped into the
memory of the chip. When otp sprom support was introduced it tried to
read out the sprom from the wireless chip also if no otp sprom was
available. This caused a Data bus error in bcma_sprom_get() when
reading out the sprom for the SoC.
This fixes a regression introduced in commit:
commit 10d8493cd9
Author: Arend van Spriel <arend@broadcom.com>
Date: Tue Mar 6 15:50:48 2012 +0100
bcma: add support for on-chip OTP memory used for SPROM storage
This patch was tested on a Netgear WNDR3400 (Broadcom BCM4718 SoC).
Reported-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following is seen during allmodconfig builds for MIPS:
drivers/bcma/driver_pci_host.c:518:2: error: implicit declaration
of function 'pcibios_enable_device' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [drivers/bcma/driver_pci_host.o] Error 1
Most likey introduced by commit 49dc957715
"bcma: add PCIe host controller"
Add the header instead of implicitly assuming it will be present.
Sounds like a good idea, but that alone doesn't fix anything.
The real problem is that the Kconfig has settings related to whether
PCI is possible, i.e.
config BCMA_HOST_PCI_POSSIBLE
bool
depends on BCMA && PCI = y
default y
config BCMA_HOST_PCI
bool "Support for BCMA on PCI-host bus"
depends on BCMA_HOST_PCI_POSSIBLE
...but what is missing is that BCMA_DRIVER_PCI_HOSTMODE doesn't
have any dependencies on the above. Add one.
CC: Hauke Mehrtens <hauke@hauke-m.de>
CC: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wireless Broadcom chips can have either their SPROM data stored
on either external SPROM or on-chip OTP memory. Both are accessed
through the same register space. This patch adds support for the
on-chip OTP memory.
Tested with:
BCM43224 OTP and SPROM
BCM4331 SPROM
BCM4313 OTP
This patch is in response to linux-wireless thread [1].
[1] http://article.gmane.org/gmane.linux.kernel.wireless.general/85426
Tested-by: Saul St. John <saul.stjohn@gmail.com>
Tested-by: Rafal Milecki <zajec5@gmail.com>
Tested-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When not SPROM is available a fallback mechanism is used. However,
when that fails the code currently continues. This patch assures
that the bcma_sprom_get() function aborts when that happens.
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On SoCs the sprom is stored in the nvram in a special partition on the
flash chip. The nvram contains the sprom for the main bus, but
sometimes also for a pci devices using bcma. This patch makes it
possible for the arch code to register a function to fetch the needed
sprom from the nvram and provide it to the bcma code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is needed by the bcm47xx arch code to get the number of
the ieee80211 core.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes us see what type of hardware someone uses by the dmesg
output.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This check is needed on the BCM43224 device as it says in the
capabilities it has an sprom but is extra check says it has not.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we have two bcma buses on one computer the second will not work
without this patch. Now each bus gets an own number.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some SoCs have a PCIe host controller to make it possible to attach
some other devices to it, like an other Wifi card.
This code was tested with an Netgear WNDR3400 (bcm4716 based), but
should work with all bcma based SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma_core_pci_hostmode_init() has to be in __devinit as it will call a
function in that section and so all functions calling it also have to
be in __devinit.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are many magic numbers used in the PCIe code. Replace them with
some constants from the Broadcom SDK and also use them in the pcie host
controller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some SoCs have two pcie or gmac cores and we need to know the number of
the specific core on the bus. This is the case for the BCM4706.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcmsmac driver is now using the bcma SPROM CRC check, which does
not recognize all chipsets that were functional prior to the switch. In
particular, the current code bails out on odd CRC errors in recent
Macbooks. This patch ignores those errors, with the argument that an
unrecognized SPROM should be treated similarly to a non-existing one.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma_bus_scan() leaks 'struct bcma_device' bytes if
bcma_get_next_core() returns error.
Restructure the code so we always kfree() the memory we allocate to
the variable 'core' before it goes out of scope.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SPROM location has been relocated again for some devices. This patch
will log the offset when CONFIG_BCMA_DEBUG has been selected.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now the low-level driver actually gets informed that it is getting suspended and resumed.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
.. and connect it up with the pci host bcma driver.
Now, the next step is to connect those bcma bus-level suspend/resume
functions to the actual bcma device suspend resume functions.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
.. and avoid doing the unnecessary PCI operations - the PCI layer will
do them for us.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This clears the currently mapped core when suspending, to force
re-mapping after resume. Without that we were touching default core
registers believing some other core is mapped. Such a behaviour
resulted in lockups on some machines.
Cc: stable@vger.kernel.org
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma used to lock up machine without enabling PCI or initializing CC.
Cc: stable@vger.kernel.org
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some cores are mapped in the fixed way, they registers can be accessed
all the time.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix in advance, or we will get things like this:
drivers/bcma/core.c:20: warning: data definition has no type or storage class
drivers/bcma/core.c:20: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
drivers/bcma/core.c:20: warning: parameter names (without types) in function declaration
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
