commit 048e3a34a2 upstream.
Stop Mode is entered when Stop Mode is requested at chip level and
MCR[LPM_ACK] is asserted by the FlexCAN.
Double check with IP owner, the MCR[LPM_ACK] bit should be polled for
stop mode acknowledgment, not the acknowledgment from chip level which
is used to gate flexcan clocks.
This patch depends on:
b7603d080f ("can: flexcan: add low power enter/exit acknowledgment helper")
Fixes: 5f186c257f (can: flexcan: fix stop mode acknowledgment)
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e707180ae2 upstream.
When suspending, and there is still CAN traffic on the interfaces the
flexcan immediately wakes the platform again. As it should :-). But it
throws this error msg:
[ 3169.378661] PM: noirq suspend of devices failed
On the way down to suspend the interface that throws the error message
calls flexcan_suspend() but fails to call flexcan_noirq_suspend(). That
means flexcan_enter_stop_mode() is called, but on the way out of suspend
the driver only calls flexcan_resume() and skips flexcan_noirq_resume(),
thus it doesn't call flexcan_exit_stop_mode(). This leaves the flexcan
in stop mode, and with the current driver it can't recover from this
even with a soft reboot, it requires a hard reboot.
This patch fixes the deadlock when using self wakeup, by calling
flexcan_exit_stop_mode() from flexcan_resume() instead of
flexcan_noirq_resume().
This also fixes another issue: CAN frames are received out-of-order in
first IRQ handler run after wakeup.
The problem is that the wakeup latency from frame reception to the IRQ
handler (where the CAN frames are sorted by timestamp) is much bigger
than the time stamp counter wrap around time. This means it's
impossible to sort the CAN frames by timestamp.
The reason is that the controller exits stop mode during noirq resume,
which means it receives frames immediately, but interrupt handling is
still not possible.
So exit stop mode during resume stage instead of noirq resume fixes this
issue.
Fixes: de3578c198 ("can: flexcan: add self wakeup support")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60552253e2 upstream.
According to section "8.3.8 RST Pin" in the datasheet we are required to
wait >700us after the device is reset.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.4
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ab79b06dd upstream.
CANFD2.0 core uses BRAM for storing acceptance filter ID(AFID) and MASK
(AFMASK)registers. So by default AFID and AFMASK registers contain random
data. Due to random data, we are not able to receive all CAN ids.
Initializing AFID and AFMASK registers with Zero before enabling
acceptance filter to receive all packets irrespective of ID and Mask.
Fixes: 0db9071353 ("can: xilinx: add can 2.0 support")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cde9319e88 upstream.
Currently the reserved region for ISA is allocated with no
permissions. If a dma domain is being used, mapping this region will
fail. Set the permissions to DMA_PTE_READ|DMA_PTE_WRITE.
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: stable@vger.kernel.org # v5.3+
Fixes: d850c2ee5f ("iommu/vt-d: Expose ISA direct mapping region via iommu_get_resv_regions")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8018a0e91 upstream.
Commit d850c2ee5f ("iommu/vt-d: Expose ISA direct mapping region via
iommu_get_resv_regions") created a direct-mapped reserved memory region
in order to replace the static identity mapping of the ISA address
space, where the latter was then removed in commit df4f3c603a
("iommu/vt-d: Remove static identity map code"). According to the
history of this code and the Kconfig option surrounding it, this direct
mapping exists for the benefit of legacy ISA drivers that are not
compatible with the DMA API.
In conjuntion with commit 9b77e5c798 ("vfio/type1: check dma map
request is within a valid iova range") this change introduced a
regression where the vfio IOMMU backend enforces reserved memory regions
per IOMMU group, preventing userspace from creating IOMMU mappings
conflicting with prescribed reserved regions. A necessary prerequisite
for the vfio change was the introduction of "relaxable" direct mappings
introduced by commit adfd373820 ("iommu: Introduce
IOMMU_RESV_DIRECT_RELAXABLE reserved memory regions"). These relaxable
direct mappings provide the same identity mapping support in the default
domain, but also indicate that the reservation is software imposed and
may be relaxed under some conditions, such as device assignment.
Convert the ISA bridge direct-mapped reserved region to relaxable to
reflect that the restriction is self imposed and need not be enforced
by drivers such as vfio.
Fixes: 1c5c59fbad ("iommu/vt-d: Differentiate relaxable and non relaxable RMRRs")
Cc: stable@vger.kernel.org # v5.3+
Link: https://lore.kernel.org/linux-iommu/20191211082304.2d4fab45@x1.home
Reported-by: cprt <cprt@protonmail.com>
Tested-by: cprt <cprt@protonmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75d1838539 upstream.
If the default DMA domain of a group doesn't fit a device, it
will still sit in the group but use a private identity domain.
When map/unmap/iova_to_phys come through iommu API, the driver
should still serve them, otherwise, other devices in the same
group will be impacted. Since identity domain has been mapped
with the whole available memory space and RMRRs, we don't need
to worry about the impact on it.
Link: https://www.spinics.net/lists/iommu/msg40416.html
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Reported-by: Jerry Snitselaar <jsnitsel@redhat.com>
Fixes: 942067f1b6 ("iommu/vt-d: Identify default domains replaced with private")
Cc: stable@vger.kernel.org # v5.3+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d360211524 upstream.
iommu_group_create_direct_mappings uses group->default_domain, but
right after it is called, request_default_domain_for_dev calls
iommu_domain_free for the default domain, and sets the group default
domain to a different domain. Move the
iommu_group_create_direct_mappings call to after the group default
domain is set, so the direct mappings get associated with that domain.
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: stable@vger.kernel.org
Fixes: 7423e01741 ("iommu: Add API to request DMA domain for device")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c80ba392b upstream.
In case the new region gets merged into another one, the nr list node is
freed. Checking its type while completing the merge algorithm leads to
a use-after-free. Use new->type instead.
Fixes: 4dbd258ff6 ("iommu: Revisit iommu_insert_resv_region() implementation")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: Qian Cai <cai@lca.pw>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Stable <stable@vger.kernel.org> #v5.3+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d23d124843 upstream.
When an application sends TPM commands in NONBLOCKING mode
the driver holds chip->tpm_mutex returning from write(),
which triggers: "WARNING: lock held when returning to user space".
To fix this issue the driver needs to release the mutex before
returning and acquire it again in tpm_dev_async_work() before
sending the command.
Cc: stable@vger.kernel.org
Fixes: 9e1b74a63f (tpm: add support for nonblocking operation)
Reported-by: Jeffrin Jose T <jeffrin@rajagiritech.edu.in>
Tested-by: Jeffrin Jose T <jeffrin@rajagiritech.edu.in>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21df4a8b60 upstream.
Instead of repeatedly calling tpm_chip_start/tpm_chip_stop when
issuing commands to the tpm during initialization, just reserve the
chip after wait_startup, and release it when we are ready to call
tpm_chip_register.
Cc: Christian Bundy <christianbundy@fraction.io>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Stefan Berger <stefanb@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Cc: linux-integrity@vger.kernel.org
Fixes: a3fbfae82b ("tpm: take TPM chip power gating out of tpm_transmit()")
Fixes: 5b359c7c43 ("tpm_tis_core: Turn on the TPM before probing IRQ's")
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f34e5bd70 upstream.
there is a chance that always get response CRC error after HS200 tuning,
the reason is that need set CMD_TA to 2. this modification is only for
MT8173.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Cc: stable@vger.kernel.org
Fixes: 1ede5cb88a ("mmc: mediatek: Use data tune for CMD line tune")
Link: https://lore.kernel.org/r/20191204071958.18553-1-chaotian.jing@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07bcc41156 upstream.
This reverts commit c894e33ddc.
This commit aims to treat SD High speed and SDR25 as the same while
setting UHS Timings in HOST_CONTROL2 which leads to failures with some
SD cards in AM65x. Revert this commit.
The issue this commit was trying to fix can be implemented in a platform
specific callback instead of common sdhci code.
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191128110422.25917-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 57d4f0b863 ]
Currently, scrub_missing_raid56_worker() puts and potentially frees
sblock (which embeds the work item) and then submits a bio through
scrub_wr_submit(). This is another potential instance of the bug in
"btrfs: don't prematurely free work in run_ordered_work()". Fix it by
dropping the reference after we submit the bio.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e732fe95e4 ]
Currently, reada_start_machine_worker() frees the reada_machine_work and
then calls __reada_start_machine() to do readahead. This is another
potential instance of the bug in "btrfs: don't prematurely free work in
run_ordered_work()".
There _might_ already be a deadlock here: reada_start_machine_worker()
can depend on itself through stacked filesystems (__read_start_machine()
-> reada_start_machine_dev() -> reada_tree_block_flagged() ->
read_extent_buffer_pages() -> submit_one_bio() ->
btree_submit_bio_hook() -> btrfs_map_bio() -> submit_stripe_bio() ->
submit_bio() onto a loop device can trigger readahead on the lower
filesystem).
Either way, let's fix it by freeing the work at the end.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd7710cb49 ]
Commit 3c1d3f0979 ("MIPS: futex: Emit Loongson3 sync workarounds
within asm") inadvertently removed the newlines following
__WEAK_LLSC_MB, which causes build failures for configurations in which
__WEAK_LLSC_MB expands to a sync instruction:
{standard input}: Assembler messages:
{standard input}:9346: Error: symbol `sync3' is already defined
{standard input}:9380: Error: symbol `sync3' is already defined
...
Fix this by restoring the newlines to separate the sync instruction from
anything following it (such as the 3: label), preventing inadvertent
concatenation.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 3c1d3f0979 ("MIPS: futex: Emit Loongson3 sync workarounds within asm")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b167191e2a ]
Commit 6570bc79c0 ("net: core: use listified Rx for GRO_NORMAL in
napi_gro_receive()") has applied batched GRO_NORMAL packets processing
to all napi_gro_receive() users, including mac80211-based drivers.
However, this change has led to a regression in iwlwifi driver [1][2] as
it is required for NAPI users to call napi_complete_done() or
napi_complete() and the end of every polling iteration, whilst iwlwifi
doesn't use NAPI scheduling at all and just calls napi_gro_flush().
In that particular case, packets which have not been already flushed
from napi->rx_list stall in it until at least next Rx cycle.
Fix this by adding a manual flushing of the list to iwlwifi driver right
before napi_gro_flush() call to mimic napi_complete() logics.
I prefer to open-code gro_normal_list() rather than exporting it for 2
reasons:
* to prevent from using it and napi_gro_flush() in any new drivers,
as it is the *really* bad way to use NAPI that should be avoided;
* to keep gro_normal_list() static and don't lose any CC optimizations.
I also don't add the "Fixes:" tag as the mentioned commit was only a
trigger that only exposed an improper usage of NAPI in this particular
driver.
[1] https://lore.kernel.org/netdev/PSXP216MB04388962C411CD0B17A86F47804A0@PSXP216MB0438.KORP216.PROD.OUTLOOK.COM
[2] https://bugzilla.kernel.org/show_bug.cgi?id=205647
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Reported-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Tested-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Reviewed-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 070eca955c ]
Fix multiple calls to init_completion for device completion
structures. Instead, initialize them during device probe and
reinitialize them later as needed.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e284b159c6 ]
In the first version of Gen P5 ASIC, chip-id was always set to 0x1750 for
all adaptor port configurations. This has been fixed in the new chip rev.
Due to this missing fix users are not able to use adaptors based on latest
chip rev of Broadcom's Gen P5 adaptors.
Fixes: ae8637e131 ("RDMA/bnxt_re: Add chip context to identify 57500 series")
Link: https://lore.kernel.org/r/1574317343-23300-2-git-send-email-devesh.sharma@broadcom.com
Signed-off-by: Naresh Kumar PBS <nareshkumar.pbs@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Luke Starrett <luke.starrett@broadcom.com>
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98998ffe52 ]
Due to recent advances in the firmware for Broadcom's gen p5 series of
adaptors the driver code to report hardware counters has been broken
w.r.t. roce devices.
The new firmware command expects dma length to be specified during stat
dma buffer allocation.
Fixes: 2792b5b95e ("bnxt_en: Update firmware interface spec. to 1.10.0.89.")
Link: https://lore.kernel.org/r/1574317343-23300-3-git-send-email-devesh.sharma@broadcom.com
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a89b2cbf71 ]
Building selftests with 'make TARGETS=bpf kselftest' was fixed in commit
55d554f5d1 ("tools: bpf: Use !building_out_of_srctree to determine
srctree"). However, by updating $(srctree) in tools/bpf/Makefile for
in-tree builds only, we leave out the case where we pass an output
directory to build BPF tools, but $(srctree) is not set. This
typically happens for:
$ make -s tools/bpf O=/tmp/foo
Makefile:40: /tools/build/Makefile.feature: No such file or directory
Fix it by updating $(srctree) in the Makefile not only for out-of-tree
builds, but also if $(srctree) is empty.
Detected with test_bpftool_build.sh.
Fixes: 55d554f5d1 ("tools: bpf: Use !building_out_of_srctree to determine srctree")
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Link: https://lore.kernel.org/bpf/20191119105626.21453-1-quentin.monnet@netronome.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5d66f8100 ]
When a phydev is created, the speed and duplex are set to zero and
-1 respectively, rather than using the predefined SPEED_UNKNOWN and
DUPLEX_UNKNOWN constants.
There is a window at initialisation time where we may report link
down using the 0/-1 values. Tidy this up and use the predefined
constants, so debug doesn't complain with:
"Unsupported (update phy-core.c)/Unsupported (update phy-core.c)"
when the speed and duplex settings are printed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e25f9152bc ]
Currently there can be a case where a DCB map is applied and there are
more interrupt vectors (vsi->num_q_vectors) than Rx queues (vsi->num_rxq)
and Tx queues (vsi->num_txq). If we try to set coalesce settings in this
case it will report a false failure. Fix this by checking if vector index
is valid with respect to the number of Tx and Rx queues configured.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f9639d2fb ]
It is wrong to set PF disable state flag for all VFs when freeing VF
resources - Instead, we should set VF disable state flag for each VF with
its resources being returned to the device. Right now, all VF opcodes,
mailbox communication to clear its resources as well fails - since we
already indicate that PF is in disable state, with all VFs not active. In
addition, we don't need to notify VF that PF is intending to reset it, if
it is already in disabled state.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d0e3ce52c ]
The INTERRUPT_CNTL2 register expects a valid DMA address, but is
currently set with a GPU MC address. This can cause problems on
systems that detect the resulting DMA read from an invalid address
(found on a Power8 guest).
Instead, use the DMA address of the dummy page because it will always
be safe.
Fixes: 27ae10641e ("drm/amdgpu: add interupt handler implementation for si v3")
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ed6751bb8 ]
With CONFIG_MIPS_VA_BITS_48=y the build fails miserably:
CC arch/mips/kernel/asm-offsets.s
In file included from arch/mips/include/asm/pgtable.h:644,
from include/linux/mm.h:99,
from arch/mips/kernel/asm-offsets.c:15:
include/asm-generic/pgtable.h:16:2: error: #error CONFIG_PGTABLE_LEVELS is not consistent with __PAGETABLE_{P4D,PUD,PMD}_FOLDED
#error CONFIG_PGTABLE_LEVELS is not consistent with __PAGETABLE_{P4D,PUD,PMD}_FOLDED
^~~~~
include/asm-generic/pgtable.h:390:28: error: unknown type name 'p4d_t'; did you mean 'pmd_t'?
static inline int p4d_same(p4d_t p4d_a, p4d_t p4d_b)
^~~~~
pmd_t
[ ... more such errors ... ]
scripts/Makefile.build:99: recipe for target 'arch/mips/kernel/asm-offsets.s' failed
make[2]: *** [arch/mips/kernel/asm-offsets.s] Error 1
This happens because when CONFIG_MIPS_VA_BITS_48 enables 4th level of the
page tables, but neither pgtable-nop4d.h nor 5level-fixup.h are included to
cope with the 5th level.
Replace #ifdef conditions around includes of the pgtable-nop{m,u}d.h with
explicit CONFIG_PGTABLE_LEVELS and add include of 5level-fixup.h for the
case when CONFIG_PGTABLE_LEVELS==4
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mm@kvack.org
Cc: Mike Rapoport <rppt@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10992af6bf ]
It is necessary to free the memory that we have allocated when error occurs.
Fixes: ef3072cd1d ("tools lib traceevent: Get rid of die in add_filter_type()")
Signed-off-by: Hewenliang <hewenliang4@huawei.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Tzvetomir Stoyanov <tstoyanov@vmware.com>
Link: http://lore.kernel.org/lkml/20191119014415.57210-1-hewenliang4@huawei.com
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ee812f614 ]
In the vmx crypto Makefile we assign to a variable called TARGET and
pass that to the aesp8-ppc.pl and ghashp8-ppc.pl scripts.
The variable is meant to describe what flavour of powerpc we're
building for, eg. either 32 or 64-bit, and big or little endian.
Unfortunately TARGET is a fairly common name for a make variable, and
if it happens that TARGET is specified as a command line parameter to
make, the value specified on the command line will override our value.
In particular this can happen if the kernel Makefile is driven by an
external Makefile that uses TARGET for something.
This leads to weird build failures, eg:
nonsense at /build/linux/drivers/crypto/vmx/ghashp8-ppc.pl line 45.
/linux/drivers/crypto/vmx/Makefile:20: recipe for target 'drivers/crypto/vmx/ghashp8-ppc.S' failed
Which shows that we passed an empty value for $(TARGET) to the perl
script, confirmed with make V=1:
perl /linux/drivers/crypto/vmx/ghashp8-ppc.pl > drivers/crypto/vmx/ghashp8-ppc.S
We can avoid this confusion by using override, to tell make that we
don't want anything to override our variable, even a value specified
on the command line. We can also use a less common name, given the
script calls it "flavour", let's use that.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08a5bdde38 ]
Commit 7b6ddeaf27 ("mac80211: use QoS NDP for AP probing")
let STAs send QoS Null frames as PS triggers if the AP was
a QoS STA. However, the mac80211 PS stack relies on an
interface flag IEEE80211_STA_NULLFUNC_ACKED for
determining trigger frame ACK, which was not being set for
acked non-QoS Null frames. The effect is an inability to
trigger hardware sleep via IEEE80211_CONF_PS since the QoS
Null frame was seemingly never acked.
This bug only applies to drivers which set both
IEEE80211_HW_REPORTS_TX_ACK_STATUS and
IEEE80211_HW_PS_NULLFUNC_STACK.
Detect the acked QoS Null frame to restore STA power save.
Fixes: 7b6ddeaf27 ("mac80211: use QoS NDP for AP probing")
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20191119053538.25979-4-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7126603d4 ]
If you try to compile this driver on a 64-bit platform then you
will get warnings because it mixes size_t with unsigned int which
only works on 32-bit.
This patch fixes all of the warnings on sun4i-ss-hash.c.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6e9da21ee ]
If you try to compile this driver on a 64-bit platform then you
will get warnings because it mixes size_t with unsigned int which
only works on 32-bit.
This patch fixes all of the warnings.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a82e23f45 ]
Linux-next commit titled "perf/core: Optimize perf_init_event()"
changed the semantics of PMU device driver registration.
It was done to speed up the lookup/handling of PMU device driver
specific events. It also enforces that only one PMU device
driver will be registered of type PERF_EVENT_RAW.
This change added these line in function perf_pmu_register():
...
+ ret = idr_alloc(&pmu_idr, pmu, max, 0, GFP_KERNEL);
+ if (ret < 0)
goto free_pdc;
+
+ WARN_ON(type >= 0 && ret != type);
The warn_on generates a message. We have 3 PMU device drivers,
each registered as type PERF_TYPE_RAW.
The cf_diag device driver (arch/s390/kernel/perf_cpumf_cf_diag.c)
always hits the WARN_ON because it is the second PMU device driver
(after sampling device driver arch/s390/kernel/perf_cpumf_sf.c)
which is registered as type 4 (PERF_TYPE_RAW).
So when the sampling device driver is registered, ret has value 4.
When cf_diag device driver is registered with type 4,
ret has value of 5 and WARN_ON fires.
Adjust the PMU device drivers for s390 to support the new
semantics required by perf_pmu_register().
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8b970c8e3 ]
Fix possible out-of-bound access of status rates array in
mt7615_fill_txs/mt7603_fill_txs routines
Fixes: c5211e997e ("mt76: mt7603: rework and fix tx status reporting")
Fixes: 4af81f02b4 ("mt76: mt7615: sync with mt7603 rate control changes")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fe579dfb9 ]
Clean CPSW ALE on init and intf restart (up/down) to avoid reading obsolete
or garbage entries from ALE table.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cca59516d ]
This reverts commit 957ce0c6b8 (ASoC: soc-pcm: check symmetry after
hw_params).
That commit cause soc_pcm_params_symmetry can't take effect.
cpu_dai->rate, cpu_dai->channels and cpu_dai->sample_bits
are updated in the middle of soc_pcm_hw_params, so move
soc_pcm_params_symmetry to the end of soc_pcm_hw_params is
not a good solution, for judgement of symmetry in the function
is always true.
FIXME:
According to the comments of that commit, I think the case
described in the commit should disable symmetric_rates
in Back-End, rather than changing the position of
soc_pcm_params_symmetry.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1573555602-5403-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21f585480d ]
New GCC warns about inappropriate use of strncpy():
drivers/staging/fbtft/fbtft-core.c: In function ‘fbtft_framebuffer_alloc’:
drivers/staging/fbtft/fbtft-core.c:665:2: warning: ‘strncpy’ specified bound 16 equals destination size [-Wstringop-truncation]
665 | strncpy(info->fix.id, dev->driver->name, 16);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Later on the copy is being used with the assumption to be NULL terminated.
Make sure string is NULL terminated by switching to snprintf().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191120095716.26628-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19b3751ffa ]
When hardware reports RX buffer errors, the latest 57500 chips do not
require reset. The packet is discarded by the hardware and the
ring will continue to operate.
Also, add an rx_buf_errors counter for this type of error. It can help
the user to identify if the aggregation ring is too small.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13f9bae579 ]
Currently if the kernel is built with CONFIG_TRACE_IRQFLAGS and KASAN
and used as crash kernel it crashes itself due to
trace_hardirqs_off/trace_hardirqs_on being called with DAT off. This
happens because trace_hardirqs_off/trace_hardirqs_on are instrumented and
kasan code tries to perform access to shadow memory to validate memory
accesses. Kasan shadow memory is populated with vmemmap, so all accesses
require DAT on.
memcpy_real could be called with DAT on or off (with kasan enabled DAT
is set even before early code is executed).
Make sure that trace_hardirqs_off/trace_hardirqs_on are called with DAT
on and only actual __memcpy_real is called with DAT off.
Also annotate __memcpy_real and _memcpy_real with __no_sanitize_address
to avoid further problems due to switching DAT off.
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0398d4ab16 ]
s390_crypto_shash_parmsize() return type is int, it
should not be stored in a unsigned variable, which
compared with zero.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 3c2eb6b76c ("s390/crypto: Support for SHA3 via CPACF (MSA6)")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Joerg Schmidbauer <jschmidb@linux.vnet.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 91e2f539ee upstream.
Fix die_walk_lines() to list the function entry line correctly. Since
the dwarf_entrypc() does not return the entry pc if the DIE has only
range attribute, __die_walk_funclines() fails to list the declaration
line (entry line) in that case.
To solve this issue, this introduces die_entrypc() which correctly
returns the entry PC (the first address range) even if the DIE has only
range attribute. With this fix die_walk_lines() shows the function entry
line is able to probe correctly.
Fixes: 4cc9cec636 ("perf probe: Introduce lines walker interface")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/157190837419.1859.4619125803596816752.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Thomas Backlund <tmb@mageia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bb1835a3b8 ]
Avoid termination of trace loading in case the last record in the
decompressed buffer partly resides in the following mmaped
PERF_RECORD_COMPRESSED record.
In this case NULL value returned by fetch_mmaped_event() means to
proceed to the next mmaped record then decompress it and load compressed
events.
The issue can be reproduced like this:
$ perf record -z -- some_long_running_workload
$ perf report --stdio -vv
decomp (B): 44519 to 163000
decomp (B): 48119 to 174800
decomp (B): 65527 to 131072
fetch_mmaped_event: head=0x1ffe0 event->header_size=0x28, mmap_size=0x20000: fuzzed perf.data?
Error:
failed to process sample
...
Testing:
71: Zstd perf.data compression/decompression : Ok
$ tools/perf/perf report -vv --stdio
decomp (B): 59593 to 262160
decomp (B): 4438 to 16512
decomp (B): 285 to 880
Looking at the vmlinux_path (8 entries long)
Using vmlinux for symbols
decomp (B): 57474 to 261248
prefetch_event: head=0x3fc78 event->header_size=0x28, mmap_size=0x3fc80: fuzzed or compressed perf.data?
decomp (B): 25 to 32
decomp (B): 52 to 120
...
Fixes: 57fc032ad6 ("perf session: Avoid infinite loop when seeing invalid header.size")
Link: https://marc.info/?l=linux-kernel&m=156580812427554&w=2
Co-developed-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/cf782c34-f3f8-2f9f-d6ab-145cee0d5322@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f61563da0 ]
This fixes a minor WARNING in the cfg80211:
[ 130.658034] ------------[ cut here ]------------
[ 130.662805] WARNING: CPU: 1 PID: 610 at net/wireless/core.c:954 wiphy_unregister+0xb4/0x198 [cfg80211]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3de88c9113 ]
Drivers use different fields to report the number of channels, so take
the maximum of all data channels (rx, tx, combined) when determining the
size of the xsk map. The current code used only 'combined' which was set
to 0 in some drivers e.g. mlx4.
Tested: compiled and run xdpsock -q 3 -r -S on mlx4
Signed-off-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/20191119001951.92930-1-lrizzo@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bb887709e ]
When the Acer Switch 10 SW5-012 quirk was added we did not have
jack-detection support yet; and the builtin microphone selection of
the original quirk is wrong too.
Fix the microphone-input quirk and add jack-detection info so that the
internal-microphone and headphone/set jack on the Switch 10 work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191119145138.59162-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 553671b768 ]
Some firmware images contain a comma, such as:
EXTRA_FIRMWARE "brcm/brcmfmac4334-sdio.samsung,gt-s7710.txt"
as Broadcom firmware simply tags the device tree compatible
string at the end of the firmware parameter file. And the
compatible string contains a comma.
This doesn't play well with gas:
drivers/base/firmware_loader/builtin/brcm/brcmfmac4334-sdio.samsung,gt-s7710.txt.gen.S: Assembler messages:
drivers/base/firmware_loader/builtin/brcm/brcmfmac4334-sdio.samsung,gt-s7710.txt.gen.S:4: Error: bad instruction `_fw_brcm_brcmfmac4334_sdio_samsung,gt_s7710_txt_bin:'
drivers/base/firmware_loader/builtin/brcm/brcmfmac4334-sdio.samsung,gt-s7710.txt.gen.S:9: Error: bad instruction `_fw_brcm_brcmfmac4334_sdio_samsung,gt_s7710_txt_name:'
drivers/base/firmware_loader/builtin/brcm/brcmfmac4334-sdio.samsung,gt-s7710.txt.gen.S:15: Error: can't resolve `.rodata' {.rodata section} - `_fw_brcm_brcmfmac4334_sdio_samsung' {*UND* section}
make[6]: *** [../scripts/Makefile.build:357: drivers/base/firmware_loader/builtin/brcm/brcmfmac4334-sdio.samsung,gt-s7710.txt.gen.o] Error 1
We need to get rid of the comma from the labels used by the
assembly stub generator.
Replacing a comma using GNU Make subst requires a helper
variable.
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191115225911.3260-1-linus.walleij@linaro.org
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Joakim Zhang
Sean Nyekjaer
Oleksij Rempel
Srinivas Neeli
Jerry Snitselaar
Alex Williamson
Lu Baolu
Eric Auger
Tadeusz Struk
Chaotian Jing
Faiz Abbas
Omar Sandoval
Paul Burton
Alexander Lobakin
Thomas Falcon
Luke Starrett
Yonghong Song
Devesh Sharma
Quentin Monnet
Russell King
Brett Creeley
Akeem G Abodunrin
Sam Bobroff
Mike Rapoport
Hewenliang
Michael Ellerman
Thomas Pedersen
Corentin Labbe
Herbert Xu
Thomas Richter
Lorenzo Bianconi
Grygorii Strashko
Shengjiu Wang
Andy Shevchenko
Johannes Berg
Michael Chan
Vasily Gorbik
YueHaibing
Masami Hiramatsu
Alexey Budankov
Rafał Miłecki
Luigi Rizzo
Adrian Hunter
Hans de Goede
Linus Walleij