With commits 08677214 and 59be5a8e, alloc_bootmem()/free_bootmem() and
friends use the early_res functions for memory management when
NO_BOOTMEM is enabled. This patch adds the kmemleak calls in the
corresponding code paths for bootmem allocations.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
The pointer to the page_cgroup table allocated in
init_section_page_cgroup() is stored in section->page_cgroup as (base -
pfn). Since this value does not point to the beginning or inside the
allocated memory block, kmemleak reports a false positive.
This was reported in bugzilla.kernel.org as #16297.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Adrien Dessemond <adrien.dessemond@gmail.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
The length filed in the chsc response block (if valid)
has a value of n*(sizeof(chp_desc))+8 (for the response
block header). When we memcopied from the response block
to the actual descriptor we copied 8 bytes too much.
The bug was not revealed since the descriptor is embedded
in struct channel_path.
Since we only write one descriptor at a time ignore the
length value and use sizeof(*desc).
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dasd_alias_show function does not return a device reference
in case the device is an alias.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Partition boundary calculation fails for DASD FBA disks under the
following conditions:
- disk is formatted with CMS FORMAT with a blocksize of more than
512 bytes
- all of the disk is reserved to a single CMS file using CMS RESERVE
- the disk is accessed using the DIAG mode of the DASD driver
Under these circumstances, the partition detection code tries to
read the CMS label block containing partition-relevant information
from logical block offset 1, while it is in fact located at physical
block offset 1.
Fix this problem by using the correct CMS label block location
depending on the device type as determined by the DASD SENSE ID
information.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current shrinker implementation requires the registered callback
to have global state to work from. This makes it difficult to shrink
caches that are not global (e.g. per-filesystem caches). Pass the shrinker
structure to the callback so that users can embed the shrinker structure
in the context the shrinker needs to operate on and get back to it in the
callback via container_of().
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
In commit f007ea26, the order of the %es and %ds segment registers
got accidentally swapped, so synthesized 'struct pt_regs' frames
have the two values inverted. It's almost sure that these values
never matter, and that they also never differ. But wrong is wrong.
Signed-off-by: Roland McGrath <roland@redhat.com>
The input handler for Type 2 Routing Header (mip6_rthdr_input())
checks if the CoA in the packet matches the CoA in the XFRM state.
Current check is buggy: it compares the adddress in the Type 2
Routing Header, i.e. the HoA, against the expected CoA in the state.
The comparison should be made against the address in the destination
field of the IPv6 header.
The bug remained unnoticed because the main (and possibly only current)
user of the code (UMIP MIPv6 Daemon) initializes the XFRM state with the
unspecified address, i.e. explicitly allows everything.
Yoshifuji-san, can you ack that one?
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2: Silence gcc warning in ocfs2_write_zero_page().
jbd2/ocfs2: Fix block checksumming when a buffer is used in several transactions
ocfs2/dlm: Remove BUG_ON from migration in the rare case of a down node
ocfs2: Don't duplicate pages past i_size during CoW.
ocfs2: tighten up strlen() checking
ocfs2: Make xattr reflink work with new local alloc reservation.
ocfs2: make xattr extension work with new local alloc reservation.
ocfs2: Remove the redundant cpu_to_le64.
ocfs2/dlm: don't access beyond bitmap size
ocfs2: No need to zero pages past i_size.
ocfs2: Zero the tail cluster when extending past i_size.
ocfs2: When zero extending, do it by page.
ocfs2: Limit default local alloc size within bitmap range.
ocfs2: Move orphan scan work to ocfs2_wq.
fs/ocfs2/dlm: Add missing spin_unlock
The hibernate issues that got fixed in commit 985b823b91 ("drm/i915:
fix hibernation since i915 self-reclaim fixes") turn out to have been
incomplete. Vefa Bicakci tested lots of hibernate cycles, and without
the __GFP_RECLAIMABLE flag the system eventually fails to resume.
With the flag added, Vefa can apparently hibernate forever (or until he
gets bored running his automated scripts, whichever comes first).
The reclaimable flag was there originally, and was one of the flags that
were dropped (unintentionally) by commit 4bdadb9785 ("drm/i915:
Selectively enable self-reclaim") that introduced all these problems,
but I didn't want to just blindly add back all the flags in commit
985b823b91, and it looked like __GFP_RECLAIM wasn't necessary. It
clearly was.
I still suspect that there is some subtle reason we're missing that
causes the problems, but __GFP_RECLAIMABLE is certainly not wrong to use
in this context, and is what the code historically used. And we have no
idea what the causes the corruption without it.
Reported-and-tested-by: M. Vefa Bicakci <bicave@superonline.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Right now ENTER doesn't always exits the newt tree widget, as it is used
for expanding/collapsing branches, but with the new tree widget being
developed we need to regain control to handle it, expanding/collapsing
branches.
In fact its really up to the ui_browser user to state what extra keys
should stop ui_browser__run, and it should handle just the ones needed
for basic browsing.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The fixed bar capability structure is searched in PCI extended
configuration space. We need to make sure there is a valid capability
ID to begin with otherwise, the search code may stuck in a infinite
loop which results in boot hang. This patch adds additional check for
cap ID 0, which is also invalid, and indicates end of chain.
End of chain is supposed to have all fields zero, but that doesn't
seem to always be the case in the field.
Suggested-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <1279306706-27087-1-git-send-email-jacob.jun.pan@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Found one x2apic system kexec loop test failed
when CONFIG_NMI_WATCHDOG=y (old) or CONFIG_LOCKUP_DETECTOR=y (current tip)
first kernel can kexec second kernel, but second kernel can not kexec third one.
it can be duplicated on another system with BIOS preenabled x2apic.
First kernel can not kexec second kernel.
It turns out, when kernel boot with pre-enabled x2apic, it will not execute
disable_local_APIC on shutdown path.
when init_apic_mappings() is called in setup_arch, it will skip setting of
apic_phys when x2apic_mode is set. ( x2apic_mode is much early check_x2apic())
Then later, disable_local_APIC() will bail out early because !apic_phys.
So check !x2apic_mode in x2apic_mode in disable_local_APIC with !apic_phys.
another solution could be updating init_apic_mappings() to set apic_phys even
for preenabled x2apic system. Actually even for x2apic system, that lapic
address is mapped already in early stage.
BTW: is there any x2apic preenabled system with apicid of boot cpu > 255?
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4C3EB22B.3000701@kernel.org>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: stable@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
ocfs2_write_zero_page() has a loop that won't ever be skipped, but gcc
doesn't know that. Set ret=0 just to make gcc happy.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
The order of freeing the IRQ and freeing the device in firmware
in ibmveth_close can cause the adapter to become unusable after a
subsequent ibmveth_open. Only a reboot of the OS will make the
network device usable again. This is seen when cycling the adapter
up and down while there is network activity.
There is a window where an IRQ will be left unserviced (H_EOI will not
be called). The solution is to make a VIO_IRQ_DISABLE h_call, free the
device with firmware, and then call free_irq.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we fail to assign resources to a PCI BAR, this patch makes us try the
original address from BIOS rather than leaving it disabled.
Linux tries to make sure all PCI device BARs are inside the upstream
PCI host bridge or P2P bridge apertures, reassigning BARs if necessary.
Windows does similar reassignment.
Before this patch, if we could not move a BAR into an aperture, we left
the resource unassigned, i.e., at address zero. Windows leaves such BARs
at the original BIOS addresses, and this patch makes Linux do the same.
This is a bit ugly because we disable the resource long before we try to
reassign it, so we have to keep track of the BIOS BAR address somewhere.
For lack of a better place, I put it in the struct pci_dev.
I think it would be cleaner to attempt the assignment immediately when the
claim fails, so we could easily remember the original address. But we
currently claim motherboard resources in the middle, after attempting to
claim PCI resources and before assigning new PCI resources, and changing
that is a fairly big job.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16263
Reported-by: Andrew <nitr0@seti.kr.ua>
Tested-by: Andrew <nitr0@seti.kr.ua>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Add alignment to syscall metadata declarations
perf: Sync callchains with period based hits
perf: Resurrect flat callchains
perf: Version String fix, for fallback if not from git
perf: Version String fix, using kernel version
The rt2x00dev->intf_work workqueue is never initialized when a driver is
probed for a non-existent device (in this case rt2500usb). On such a
path we call rt2x00lib_remove_dev() to free any resources initialized
during the probe before we use INIT_WORK to initialize the workqueue.
This causes lockdep to get confused since the lock used in the workqueue
hasn't been initialized yet but is now being acquired during
cancel_work_sync() called by rt2x00lib_remove_dev().
Fix this by initializing the workqueue first before we attempt to probe
the device. This should make lockdep happy and avoid breaking any
assumptions about how the library cleans up after a probe fails.
phy0 -> rt2x00lib_probe_dev: Error - Failed to allocate device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 2027, comm: modprobe Not tainted 2.6.35-rc5+ #60
Call Trace:
[<ffffffff8105fe59>] register_lock_class+0x152/0x31f
[<ffffffff81344a00>] ? usb_control_msg+0xd5/0x111
[<ffffffff81061bde>] __lock_acquire+0xce/0xcf4
[<ffffffff8105f6fd>] ? trace_hardirqs_off+0xd/0xf
[<ffffffff81492aef>] ? _raw_spin_unlock_irqrestore+0x33/0x41
[<ffffffff810628d5>] lock_acquire+0xd1/0xf7
[<ffffffff8104f037>] ? __cancel_work_timer+0x99/0x17e
[<ffffffff8104f06e>] __cancel_work_timer+0xd0/0x17e
[<ffffffff8104f037>] ? __cancel_work_timer+0x99/0x17e
[<ffffffff8104f136>] cancel_work_sync+0xb/0xd
[<ffffffffa0096675>] rt2x00lib_remove_dev+0x25/0xb0 [rt2x00lib]
[<ffffffffa0096bf7>] rt2x00lib_probe_dev+0x380/0x3ed [rt2x00lib]
[<ffffffff811d78a7>] ? __raw_spin_lock_init+0x31/0x52
[<ffffffffa00bbd2c>] ? T.676+0xe/0x10 [rt2x00usb]
[<ffffffffa00bbe4f>] rt2x00usb_probe+0x121/0x15e [rt2x00usb]
[<ffffffff813468bd>] usb_probe_interface+0x151/0x19e
[<ffffffff812ea08e>] driver_probe_device+0xa7/0x136
[<ffffffff812ea167>] __driver_attach+0x4a/0x66
[<ffffffff812ea11d>] ? __driver_attach+0x0/0x66
[<ffffffff812e96ca>] bus_for_each_dev+0x54/0x89
[<ffffffff812e9efd>] driver_attach+0x19/0x1b
[<ffffffff812e9b64>] bus_add_driver+0xb4/0x204
[<ffffffff812ea41b>] driver_register+0x98/0x109
[<ffffffff813465dd>] usb_register_driver+0xb2/0x173
[<ffffffffa00ca000>] ? rt2500usb_init+0x0/0x20 [rt2500usb]
[<ffffffffa00ca01e>] rt2500usb_init+0x1e/0x20 [rt2500usb]
[<ffffffff81000203>] do_one_initcall+0x6d/0x17a
[<ffffffff8106cae8>] sys_init_module+0x9c/0x1e0
[<ffffffff8100296b>] system_call_fastpath+0x16/0x1b
Signed-off-by: Stephen Boyd <bebarino@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Strip the cap and dentry releases from replayed messages. They can
cause the shared state to get out of sync because they were generated
(with the request message) earlier, and no longer reflect the current
client state.
Signed-off-by: Sage Weil <sage@newdream.net>
Replayed rename operations (after an mds failure/recovery) were broken
because the request paths were regenerated from the dentry names, which
get mangled when d_move() is called.
Instead, resend the previous request message when replaying completed
operations. Just make sure the REPLAY flag is set and the target ino is
filled in.
This fixes problems with workloads doing renames when the MDS restarts,
where the rename operation appears to succeed, but on mds restart then
fails (leading to client confusion, app breakage, etc.).
Signed-off-by: Sage Weil <sage@newdream.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
GFS2: rename causes kernel Oops
GFS2: BUG in gfs2_adjust_quota
GFS2: Fix kernel NULL pointer dereference by dlm_astd
GFS2: recovery stuck on transaction lock
GFS2: O_TRUNC not working on stuffed files across cluster
Invert the return value of die_compare_name(), because it returns a 'bool'
result which should be expeced true if the die's name is same as compared
string.
LKML-Reference: <4C36EBED.1000006@hitachi.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Gcc generates DW_AT_comp_dir and stores relative source path if building kernel
without O= option. In that case, perf probe --line sometimes doesn't work
without --source option, because it tries to access relative source path.
This adds DW_AT_comp_dir support to perf probe for finding an absolute source
path when no --source option.
LKML-Reference: <4C36EBE7.3060802@hitachi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Guest can trigger packet truncation by posting
a very short buffer and disabling buffer merging.
Convert pr_err to pr_debug to avoid log from filling
up when this happens.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
No need to take address, w90p910_ts is already a pointer.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This was detected using two mcast router tables. The
pimreg for the second interface did not have a specific
mrule, so packets received by it were handled by the
default table, which had nothing configured.
This caused the ipmr_fib_lookup to fail, causing
the memory leak.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The asics in question have the following requirements with regard to
their gart setups:
1. The GART aperture size has to be in the form of 2^X bytes, where X is from 25 to 31
2. The GART aperture MC base has to be aligned to a boundary equal to the size of the
aperture.
3. The GART page table has to be aligned to the boundary equal to the size of the table.
4. The GART page table size is: table_entry_size * (aperture_size / page_size)
5. The GART page table has to be allocated in non-paged, non-cached, contiguous system
memory.
This patch takes care 2. The rest should already be handled properly.
This fixes a regression noticed by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
OCFS2 uses t_commit trigger to compute and store checksum of the just
committed blocks. When a buffer has b_frozen_data, checksum is computed
for it instead of b_data but this can result in an old checksum being
written to the filesystem in the following scenario:
1) transaction1 is opened
2) handle1 is opened
3) journal_access(handle1, bh)
- This sets jh->b_transaction to transaction1
4) modify(bh)
5) journal_dirty(handle1, bh)
6) handle1 is closed
7) start committing transaction1, opening transaction2
8) handle2 is opened
9) journal_access(handle2, bh)
- This copies off b_frozen_data to make it safe for transaction1 to commit.
jh->b_next_transaction is set to transaction2.
10) jbd2_journal_write_metadata() checksums b_frozen_data
11) the journal correctly writes b_frozen_data to the disk journal
12) handle2 is closed
- There was no dirty call for the bh on handle2, so it is never queued for
any more journal operation
13) Checkpointing finally happens, and it just spools the bh via normal buffer
writeback. This will write b_data, which was never triggered on and thus
contains a wrong (old) checksum.
This patch fixes the problem by calling the trigger at the moment data is
frozen for journal commit - i.e., either when b_frozen_data is created by
do_get_write_access or just before we write a buffer to the log if
b_frozen_data does not exist. We also rename the trigger to t_frozen as
that better describes when it is called.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Markers have been removed, but we forgot to remove their
section.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
The ksym (breakpoint) ftrace plugin has been superseded by perf
tools that are much more poweful to use the cpu breakpoints.
This tracer doesn't bring more feature. It has been deprecated
for a while now, lets remove it.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
ftrace and perf events now use the same development branch.
Don't show a stale branch to developers.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
For migration, we are waiting for DLM_LOCK_RES_MIGRATING flag to be set
before sending DLM_MIG_LOCKRES_MSG message to the target. We are using
dlm_migration_can_proceed() for that purpose. However, if the node is
down, dlm_migration_can_proceed() will also return "go ahead". In this
rare case, the DLM_LOCK_RES_MIGRATING flag might not be set yet. Remove
the BUG_ON() that trips over this condition.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
During CoW, the pages after i_size don't contain valid data, so there's
no need to read and duplicate them.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
commit 30a564be (x86, hpet: Restrict read back to affected ATI
chipset) restricted the workaround for the HPET bug to SMX00
chipsets. This was reasonable as those were the only ones against
which we ever got a bug report.
Stephan Wolf reported now that this patch breaks his IXP400 based
machine. Though it's confirmed to work on other IXP400 based systems.
To error out on the safe side, we force the HPET readback workaround
for all ATI SMbus class chipsets.
Reported-by: Stephan Wolf <stephan@letzte-bankreihe.de>
LKML-Reference: <alpine.LFD.2.00.1007142134140.3321@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Stephan Wolf <stephan@letzte-bankreihe.de>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
We flush under vq mutex when changing backends.
This creates a deadlock as workqueue being flushed
needs this lock as well.
https://bugzilla.redhat.com/show_bug.cgi?id=612421
Drop the vq mutex before flush: we have the device mutex
which is sufficient to prevent another ioctl from touching
the vq.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch fixes a kernel Oops in the GFS2 rename code.
The problem was in the way the gfs2 directory code was trying
to re-use sentinel directory entries.
In the failing case, gfs2's rename function was renaming a
file to another name that had the same non-trivial length.
The file being renamed happened to be the first directory
entry on the leaf block.
First, the rename code (gfs2_rename in ops_inode.c) found the
original directory entry and decided it could do its job by
simply replacing the directory entry with another. Therefore
it determined correctly that no block allocations were needed.
Next, the rename code deleted the old directory entry prior to
replacing it with the new name. Therefore, the soon-to-be
replaced directory entry was temporarily made into a directory
entry "sentinel" or a place holder at the start of a leaf block.
Lastly, it went to re-add the replacement directory entry in
that leaf block. However, when gfs2_dirent_find_space was
looking for space in the leaf block, it used the wrong value
for the sentinel. That threw off its calculations so later
it decides it can't really re-use the sentinel and therefore
must allocate a new leaf block. But because it previously decided
to re-use the directory entry, it didn't waste the time to
grab a new block allocation for the inode. Therefore, the
inode's i_alloc pointer was still NULL and it crashes trying to
reference it.
In the case of sentinel directory entries, the entire dirent is
reused, not just the "free space" portion of it, and therefore
the function gfs2_dirent_find_space should use the value 0
rather than GFS2_DIRENT_SIZE(0) for the actual dirent size.
Fixing this calculation enables the reproducer programs to work
properly.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
HighMem pages on i686 do not get mapped to the buffer_heads and this was
causing a NULL pointer dereference when we were trying to memset page buffers
to zero.
We now use zero_user() that kmaps the page and directly manipulates page data.
This patch also fixes a boundary condition that was incorrect.
Signed-off-by: Abhi Das <adas@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch fixes a problem in an error path when looking
up dinodes. There are two sister-functions, gfs2_inode_lookup
and gfs2_process_unlinked_inode. Both functions acquire and
hold the i_iopen glock for the dinode being looked up. The last
thing they try to do is hold the i_gl glock for the dinode.
If that glock fails for some reason, the error path was
incorrectly calling gfs2_glock_put for the i_iopen glock twice.
This resulted in the glock being prematurely freed. The
"minimum hold time" usually kept the glock in memory, but the
lock interface to dlm (aka lock_dlm) freed its memory for the
glock. In some circumstances, it would cause dlm's dlm_astd daemon
to try to call the bast function for the freed lock_dlm memory,
which resulted in a NULL pointer dereference.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch fixes bugzilla bug #590878: GFS2: recovery stuck on
transaction lock. We set the frozen flag on the glock when we receive
a completion that cannot be delivered due to blocked locks. At that
point we check to see whether the first waiting holder has the noexp
flag set. If the noexp lock is queued later, then we need to unfreeze
the glock at that point in time, namely, in the glock work function.
This patch was originally written by Steve Whitehouse, but since
he's on holiday, I'm submitting it. It's been well tested with a
complex recovery test called revolver.
Signed-off-by: Steve Whitehouse <swhiteho@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
