Message "0271 Illegal State Transition: node" seen in logs, all luns are
unuseable for that target.
A window exists in the rcv_plogi path where if the state is plogi issue
but the driver has not issued a plogi, then two reglogins will be sent
for the same RPI. The first one to complete will advance the state to
prli issue the second one will be detected as an illegal state, and
leave the node in an unusable state.
Correct the completion routine for the PLOGI ACC that detects the state
change when the driver starts discovery on the node again and drop the
REGLOGIN mailbox command.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If there are IO's running and host reset or chip reset is triggered,
IO's can fail due to rport time out. During chip reset recovery process,
driver notifies the transport layer that remote port no longer exist, by
calling fc_remote_port_delete(). When this function is called, it
actually delays deletion by "blocking" it. It sets the remote port state
to "FC_PORTSTATE_BLOCKED" and sets FC_RPORT_DEVLOSS_PENDING. When
driver tries to abort the command by calling its abort handler function,
abort handler will wait until remote port state is blocked state or wait
for dev_loss_tmo time. Due to this blocking, rport times out and results
in an IO failure. This patch adds a check for any active reset process
before calling abort handler function.
[mkp: typo]
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If queue count is zero while reading FW dump template, for entry
T263/T274, skip capturing those entries during FW dump capture.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When RSCN is delivered for specific remote port. Use ADISC to verify the
session is still valid or not.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ql2xmaxqdepth is the module parameter that seeds the per target
queue depth in the Scsi midlayer (sdev->queue_depth). Performance
testing revealed that increasing this value would improve IOPS
numbers under certain workloads.
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we tear down the NPIV host configuration in target mode, the
qla_tgt struct was left dangling on the global list. This patch cleans
up link list and frees memory.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If SNS fabric login fails, set loop resync flag to retry via dpc.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Calling sp->free() ensures the context-correct free routine is called.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SFP can come in 2 formats: short range/SR and long range/LR. For LR,
user the can increase the number of Buffer to Buffer credits between end
points via Cavium's command line tool. By default, FW uses a lower BB
Credit value optimized for SR. This patch will read the SFP for each
link up event and during chip reset sequence. If the SFP type and
setting are mismatch, then the chip is reset 1 time to use the
appropriate setting.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The Get Port Speed switch command needs the fabric port name of the
remote device. Current code uses the registered WWPN.
Fixes: 726b854870 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update ha->wq max_active from 1 to default. MQ interrupts are queued up
via this work queue. This allows interrupts to be process in parrallel,
instead of serialized by the work queue.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove extra register read for each interrupt for performance
improvement.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For NPIV ports, call configure_hba() so that NPIV ports can proceed to
loop initialization.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If FA-WWPN feature disabled on the switch side and enabled for the
adapter, then driver would update the port name with switch port name.
This patch fixes issue by checking correct BIT flag to validate.
Fixes: 41dc529a46 ("qla2xxx: Improve RSCN handling in driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver will perform following
- Set PFLG_DRIVER_REMOVING flag and do not disable PCIe error reporting
during adapter shutdown.
- If PCIe device count is already zero, return correct error type from
PCI error interface.
- When device is offline, return correct error type from PCIe error
path.
- If there is board disable thread active during shutdown and PCIe
device count is zero then cancel scheduling board disable thread
during shutdown and return.
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Darren Trap <darren.trap@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver held spinlocks during callbacks for NVME errors which
resulted in a deadlock because recovery LS cmds needed the same lock.
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Following error will be logged in to message file while trying to
configure target with multiqueue.
"Cmd 0x1f aborted with timeout since ISP Abort is pending"
"qla25xx_init_queues Rsp que: 1 init failed."
Fixes: 82de802ad4 ("scsi: qla2xxx: Preparation for Target MQ.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix incorrect second argument for wait_event_timeout()
Fixes: c4a9b538ab ("qla2xxx: Allow vref count to timeout on vport delete.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After a kill adapter, since the cmd_status is not set, the IOCTLs will
be hung in driver resulting in application hang. Set cmd_status
MFI_STAT_WRONG_STATE when completing pended IOCTLs.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver's local RAID map is accessed frequently. We will first try to get
memory from __get_free_pages. If this fails, fall back to using vmalloc.
For crash dump buffers always prefer vmalloc.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In TM code, smid_task is valid only in case of task aborts.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
megasas_wait_for_outstanding_fusion checks for pending commands every 1
second. But megasas_complete_cmd_dpc_fusion is only called every 5
seconds. If the commands are already completed by firmware, there is an
additional delay of 5 seconds before driver will process completion for
these commands.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Similar to task abort case, use synchronize_irq API in target reset
case. Also, remove redundant call to megasas_complete_cmd_dpc_fusion
after calling megasas_sync_irqs in task abort case.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Setting resetwaittime to 0 during a FW fault will result in driver not
calling the OCR.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver allocated 256 byte MFI frames bytes but while sending MFI frame
(embedded inside chain frame of MPT frame) to firmware, driver sets the
length as 4k. This results in DMA read error messages during boot.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove variable assignments. The value stored in local variable _rc_ is
overwritten at line 2448:rc = lpfc_sli4_bsg_set_link_diag_state(phba,
0); before it can be used.
Addresses-Coverity-ID: 1226935
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Take f_mutex around mmap() processing to protect against races with the
SG_SET_RESERVED_SIZE ioctl. Ensure the reserve buffer length remains
consistent during the mapping operation, and set the "mmap called" flag
to prevent further changes to the reserved buffer size as an atomic
operation with the mapping.
[mkp: fixed whitespace]
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 1bc0eb0446 ("scsi: sg: protect accesses to 'reserved' page
array") adds needed concurrency protection for the "reserve" buffer.
Some checks that are initially made outside the lock are replicated once
the lock is taken to ensure the checks and resulting decisions are made
using consistent state.
The check that a request with flag SG_FLAG_MMAP_IO set fits in the
reserve buffer also needs to be performed again under the lock to ensure
the reserve buffer length compared against matches the value in effect
when the request is linked to the reserve buffer. An -ENOMEM should be
returned in this case, instead of switching over to an indirect buffer
as for non-MMAP_IO requests.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The parentheses are in the wrong place so we specify the length as
"sizeof(this_device->device_id) < 0" which is zero.
Fixes: 988b87edd231 ("scsi: hpsa: Ignore errors for unsupported LV_DEVICE_ID VPD page")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
pnp_device_id are not supposed to change at runtime. All functions
working with pnp_device_id provided by <linux/pnp.h> work with const
pnp_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If scsi_host_template->host_reset is NULL and the user requests an
adapter reset through
echo adapter > /sys/class/scsi_host/hostx/host_reset
-EINVAL will be returned even though the "adapter" argument is perfectly
valid.
Change this so that we only return -EINVAL if the provided string is
invalid. If the host does not implement a ->host_reset function we'll
return -EOPNOTSUPP.
[mkp: tweaked patch description]
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
struct scsi_changer needs refcounting as the device might be removed
while the fd is still open.
[mkp: whitespace]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Refactor code in order to avoid identical code for different branches.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
pnp_device_id are not supposed to change at runtime. All functions
working with pnp_device_id provided by <linux/pnp.h> work with const
pnp_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Because we were passing 'qedf_debug' instead of 'debug' to the
MODULE_PARM_DESC() macro, modinfo listed the parameter name as 'qedf_debug'
instead of it's proper name 'debug'. Correct the parameter name.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is no ordering required for the various workqueues the driver uses
so they can be converted to regular workqueues.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently in the driver the qedf_ctx attribute vlan_hw_insert is used to
which whether to insert a VLAN tag in FIP frames (except for FIP VLAN
request which is explicitly sent out untagged at least from the driver's
point of view).
When we receive a FIP VLAN response, we set qedf->vlan_hw_insert to 0 which
makes the qedf_fip_send function insert the VLAN. However when we exhaust
our FIP VLAN retries, we do not set qedf->vlan_hw_insert to 0 which means
that the driver will not tag the FIP frame with the correct VLAN ID. The
result that was observed on the wire is that some entity either in the LL2
or L2 firmware is adding a NULL VLAN tag which can cause FIP solicitation
to fail.
The offload FCoE frame function, qedf_xmit, does not use the vlan_hw_insert
attribute to decide whether to tag frames with the FIP/FCoE VLAN. Instead
it unilaterially tags the offload frames with the VLAN ID stored in
qedf->vlan_id. This is the correct behavior so the driver can guarantee
that non-offload FIP frames go out with the correct VLAN ID.
Also use the Linux network layer helpers instead of doing the VLAN insert
manually.
Also fix setting the fallback VLAN so that it used the module parameter and
is not hardcoded to 1002 (though 1002 is the default).
[mkp: fixed typo]
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently in the driver we've been using the fc_fcoe_set_mac() function to
set the source MAC for FCoE traffic. This works well in most cases as it
uses the spec. default FCF-MAC. However, if the administrator changes the
FCF-MAC switch, then any FCoE traffic we send will be dropped by the
switch.
Instead we should check the granted MAC from the FLOGI payload and use that
address if it is present. Otherwise, fall back to using the the default
FCF-MAC and the fabric ID of the port as the FCoE MAC address.
Once this address is known we need to set it when doing non-offload
traffic, offload traffic and setting the data_src_address libfcoe uses for
FIP keep alive messages.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If dev_info.wwpn and dev_info.wwnn are set by qed use these values to set
the WWNs of the port. Otherwise fall back to the old method using
fcoe_wwn_from_mac().
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to variable name, sfp_additonal_info should be
sfp_additional_info (add in missing i).
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code looks like this:
i = ntohl(aux->filemark_cnt);
if (STp->header_cache != NULL && i < OS_FM_TAB_MAX && (i > STp->filemark_cnt ||
STp->first_frame_position - 1 != ntohl(STp->header_cache->dat_fm_tab.fm_tab_ent[i]))) {
If i is negative then it's less than OS_FM_TAB_MAX so we read before
the start of the STp->header_cache->dat_fm_tab.fm_tab_ent[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The for loop is statement is missing an indent, add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An optional discovery status should be printed with a pr_cont and needs
a leading space to make it more readable. The final new line should also
be a pr_cont and the indentation is out by one, so fix that too.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Simple subenclosures do not need to support SES page 2, so make it
optional.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The printk was using the result as argument, leading to a slightly
confusing log message.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We should be checking the return code from ses_recv_diag() to avoid
accessing invalid data.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As the cciss driver has been removed there are no overlapping
PCI IDs anymore, and the 'hpsa_allow_any' flag can be removed.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hpsa driver now has support for all boards the cciss driver
used to support, so this patch removes the cciss driver and
make hpsa an alias to cciss.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Legacy boards might not support the 'extended' report luns format,
but as this is to be expected we don't need to print out an error here.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Legacy boards might not support the LV_DEVICE_ID VPD page, so
we shouldn't print out an error message here.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Legacy boards might not support volume status, so assume
the volume is online here.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for legacy boards, ensuring to enable the driver for
those boards only when 'hpsa_allow_any' is set.
The attribute 'legacy_board' is set to '1' if the device is
a legacy board, and '0' otherwise.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
'rc' is known to be 0 at this point. If 'create_context()' fails,
returns -ENOMEM instead of 0 which means success.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On parisc I see this UBSAN warning with a sym53c896:
UBSAN: Undefined behaviour in ./drivers/scsi/sym53c8xx_2/sym_hipd.c:762:24
index -1903078336 is out of range for type 'u32 [7]'
Avoid this warning by switching to div64_ul().
[mkp: fix typo]
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While the 'state' attribute can (and will) change occasionally,
calling 'poll()' or 'select()' on it fails as sysfs is never
notified that the state has changed.
With this patch calling 'poll()' or 'select()' will work
properly.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rework scsi_internal_device_unblock_nowait() into using a switch
statement. No functional changes.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with const
pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since switching to blk-mq as the default in commit 5c279bd9e4
("scsi: default to scsi-mq"), virtio-scsi LUNs consume about 10x as
much kernel memory.
qemu currently allocates a fixed 128 entry virtqueue. can_queue
currently is set to 1024. But with indirect descriptors, each command
in the queue takes 1 virtqueue entry, so the number of commands which
can be queued is equal to the length of the virtqueue.
Note I intend to send a patch to qemu to allow the virtqueue size to be
configured from the qemu command line.
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[qed_sp_iscsi_func_start:189(host_7-0)]Cannot satisfy CQ amount. Queues
requested 8, CQs available 4. Aborting function start
Above condition will resolve as management firmware is capable of
telling us the number of CQs available for a given PF, qed will
communicate the same number to qedi, So that qedi will know how much CQs
are allowed.
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver version is not updated with changes to the driver, so it has
no value, so just get rid of it.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instances of kfree(shost) should be replaced with scsi_host_put().
In addition, a missing scsi_host_put() is added for error path in
hisi_sas_shost_alloc_pci() and v3 driver removal.
Signed-off-by: Pan Bian <bianpan2016@163.com> # For main.c changes
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable res only holds value 0, so remove it.
This cleans up a coccicheck warning.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add function to set linkrate for v3 hw.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch updates some register setting according to recommendation
from HW designer and experiment.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use ACPI "_RST" method to reset the controller, since FLR is not
supported.
Function hisi_sas_stop_phys() is introduced to remove some code
duplication.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
At the beginning of 'qedf_srr_compl()' and of 'qedf_rec_compl()', we
check if 'orig_io_req' is NULL. If this happens, a NULL pointer
dereference will occur in the error handling path.
Fix it by adding an additional label in the error handling path in order
to avoid this NULL pointer dereference.
[mkp: typo]
Fixes: 61d8658b4a ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Six minor and error leg fixes, plus one major change: the reversion of
scsi-mq as the default. We're doing the latter temporarily (with a
backport to stable) to give us time to fix all the issues that turned
up with this default before trying again.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=aB/i
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six minor and error leg fixes, plus one major change: the reversion of
scsi-mq as the default.
We're doing the latter temporarily (with a backport to stable) to give
us time to fix all the issues that turned up with this default before
trying again"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxgb4i: call neigh_event_send() to update MAC address
Revert "scsi: default to scsi-mq"
scsi: sd_zbc: Write unlock zone from sd_uninit_cmnd()
scsi: aacraid: Fix out of bounds in aac_get_name_resp
scsi: csiostor: fail probe if fw does not support FCoE
scsi: megaraid_sas: fix error handle in megasas_probe_one
If "val" is SG_MAX_QUEUE then we are one element beyond the end of the
"rinfo" array so the > should be >=.
Fixes: 109bade9c6 ("scsi: sg: use standard lists for sg_requests")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since ipr RAID arrays do not support the MAINTENANCE_IN /
MI_REPORT_SUPPORTED_OPERATION_CODES, set no_report_opcodes to prevent it
from being sent.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A couple of minor fixes (st, ses) and some bigger driver fixes for
qla2xxx (crash triggered by fw dump) and ipr (lockdep problems with
mq).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=gE+M
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A couple of minor fixes (st, ses) and some bigger driver fixes for
qla2xxx (crash triggered by fw dump) and ipr (lockdep problems with
mq)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ses: Fix wrong page error
scsi: ipr: Fix scsi-mq lockdep issue
scsi: st: fix blk_get_queue usage
scsi: qla2xxx: Fix system crash while triggering FW dump
If nud_state is not valid then call neigh_event_send() to update MAC
address.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Defaulting to scsi-mq in 4.13-rc has shown various regressions
on setups that we didn't previously consider. Fixes for them are
in progress, but too invasive to make it in this cycle. So for
now revert the commit that defaults to blk-mq for SCSI. For 4.14
we'll plan to try again with these fixes.
This reverts commit 5c279bd9e4.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Releasing a zone write lock only when the write commnand that acquired
the lock completes can cause deadlocks due to potential command
reordering if the lock owning request is requeued and not executed. This
problem exists only with the scsi-mq path as, unlike the legacy path,
requests are moved out of the dispatch queue before being prepared and
so before locking a zone for a write command.
Since sd_uninit_cmnd() is now always called when a request is requeued,
call sd_zbc_write_unlock_zone() from that function for write requests
that acquired a zone lock instead of from sd_done(). Acquisition of a zone
lock by a write command is indicated using the new command
flag SCMD_ZONE_WRITE_LOCK.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <Bart.VanAssche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We terminate the aac_get_name_resp on a byte that is outside the bounds
of the structure. Extend the return response by one byte to remove the
out of bounds reference.
Fixes: b836439faf ("aacraid: 4KB sector support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fail probe if FCoE capability is not enabled in the firmware.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
megasas_mgmt_info.max_index has increased by 1 before megasas_io_attach,
if megasas_io_attach return error, then goto fail_io_attach,
megasas_mgmt_info.instance has a wrong index here. So first reduce
max_index and then set that instance to NULL.
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds calls to kill CQ takslets v3 hw during probe failure.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The channel interrupt is to process all the interrupts except PHY
UP/DOWN and broadcast interrupt. So we need to clear all the interrupts
except those 3 interrupts after processing channel interrupts.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify STP link timer from 10ms to 500ms. Also add the register address.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For v3 hw, internal abort function required status and command buffer to
be set, so add necessary code for this.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add two ATA commands, ATA_CMD_ZAC_MGMT_IN and ATA_CMD_ZAC_MGMT_OUT in
hisi_sas_get_ata_protocol(), to support SATA SMR disk.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is a fix related to freeing a device in v2 hw driver.
Before, we polled to ITCT CLR interrupt to check if a device is free.
This was error prone, as if the interrupt doesn't occur in 10us, we miss
processing it.
To avoid this situation, service this interrupt and sync the event with
a completion.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support to clean-up allocated IRQs and kill tasklets
when probe fails and for driver removal.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch removes some repeated configurations:
(1) The device id of the device is already set in the alloc function, so
we don't need to modify in free device function.
(2) Field dev_type and dev_status are configured in hisi_sas_dev_gone(),
so there is no need for repeated config in free_device_v3_hw.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code to print ECC errors in v2 hw driver is very repetitive. This
patch condensed the code by looping an array of errors.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add DFX feature for v2 hw. We are adding support for
the following errors:
- loss_of_dword_sync_count
- invalid_dword_count
- phy_reset_problem_count
- running_disparity_error_count
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The value dw0 is the residual bytes when UNDERFLOW error happens, but we
filled the residual with the value of dw3 before. So change the residual
from dw3 to dw0.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When some interrupts happen together, we need to process every interrupt
one-by-one, and should not return immediately when one interrupt process
is finished being processed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provides fixes for the following issues:
1. Fix issue of controller reset required to send commands. For reset
process, it may be required to send commands to the controller, but
not during soft reset. So add HISI_SAS_NOT_ACCEPT_CMD_BIT to prevent
executing a task during this period.
2. Send a broadcast event in rescan topology to detect any topology
changes during reset.
3. Previously it was not ensured that libsas has processed the PHY up
and down events after reset. Potentially this could cause an issue
that we still process the PHY event after reset. So resolve this by
flushing shot workqueue in LLDD reset.
4. Port ID requires refresh after reset. The port ID generated after
reset is not guaranteed to be the same as before reset, so it needs
to be refreshed for each device's ITCT.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver’s PCI IDs to match the latest Microsemi controllers
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add PQI reset to driver shutdown callback to work around controller bug.
During an 1.) OS shutdown or 2.) kexec outside of a kdump, the Linux
kernel will clear BME on our controller.
If BME is cleared during a controller/host PCIe transfer, the controller
will lock up.
So we perform a PQI reset in the driver's shutdown callback function to
eliminate the possibility of a controller/host PCIe transfer being
active when the kernel clears BME immediately after calling the driver's
shutdown callback.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- make pass-thru requests bi-directional
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- distinguish between shutdown and non-shutdown.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The null check on pHba->channel[chan].device is redundant because
device is an array and hence can never be null. Remove the check.
Detected by CoverityScan, CID#115362 ("Array compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The return value of dma_map_single() should be checked by
dma_mapping_error(). However, in function qla26xx_dport_diagnostics(), its
return value is checked against NULL, which could result in failures.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The return value of scsi_host_alloc() should be released by
scsi_host_put(). However, in function mvs_pci_init(), kfree()
is used. This patch replaces kfree() with scsi_host_put() to avoid
possible memory leaks.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function pm8001_pci_probe(), on errors that the control flow jumps to
label err_out_ha_free, function pm8001_free() is called. In pm8001_free(),
scsi_host_put() is called to release shost, which keeps the return value
of scsi_host_alloc(). After pm8001_free() returns, kfree() is called to
free shost again, resulting in a double free bug. This patch removes
scsi_host_put() from pm8001_free() and explicitly calls scsi_host_put()
to release Scsi_Host in need.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fix allocate instance->pd_info twice which was introduced by 96188a89cc.
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After sending a message, always clear esp->msg_out_len. Otherwise,
eh_abort_handler may subsequently fail to send an ABORT TASK SET
message.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch improves readability. There are no functional changes.
Since this touches on a questionable ESP_INTR_DC conditional, add some
commentary to help others who may (as I did) find themselves chasing an
"Invalid Command" error after the device flags this condition.
This cleanup also eliminates a warning from "make W=1":
drivers/scsi/esp_scsi.c: In function 'esp_finish_select':
drivers/scsi/esp_scsi.c:1233:5: warning: variable 'orig_select_state' set but not used [-Wunused-but-set-variable]
u8 orig_select_state;
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When in MESSAGE IN phase, the ESP device does not automatically
acknowledge each byte that is transferred by PIO. The mac_esp driver
neglects to explicitly ack them, which causes a timeout during messages
larger than one byte (e.g. tag bytes during reconnect). Fix this with an
ESP_CMD_MOK command after each byte.
The MESSAGE IN phase is also different in that each byte transferred
raises ESP_INTR_FDONE. So don't exit the transfer loop for this interrupt,
for this phase.
That resolves the "Reconnect IRQ2 timeout" error on those Macs which use
PIO transfers instead of PDMA. This patch also improves on the weak tests
for unexpected interrupts and phase changes during PIO transfers.
Tested-by: Stan Johnson <userm57@yahoo.com>
Fixes: 02507a80b3 ("[PATCH] [SCSI] mac_esp: fix PIO mode, take 2")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid the following warning from "make C=1":
CHECK drivers/scsi/mac_esp.c
drivers/scsi/mac_esp.c:357:30: warning: incorrect type in initializer (different address spaces)
drivers/scsi/mac_esp.c:357:30: expected unsigned char [usertype] *fifo
drivers/scsi/mac_esp.c:357:30: got void [noderef] <asn:2>*
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add const to bin_attribute structures as they are only passed to the
functions system_{remove/create}_bin_file. The arguments passed are of
type const, so declare the structures to be const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If cxgbi_ep_connect() is called with valid shost then find associated
ndev and use ndev->ifindex to find route.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the lines above this test, 8 'kzalloc' are performed, but only 7
results are tested.
Add the missing one (i.e. '!ioc->port_enable_cmds.reply').
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Regenerate firmware files to make cleaner base for following fix.
This removes some unused definitions and reorders some #defines, but
the code remains the same.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, calls to nvmet_fc_rcv_fcp_req() always copied the
FC-NVME cmd iu to a temporary buffer before returning, allowing
the driver to immediately repost the buffer to the hardware.
To address timing conditions on queue element structures vs async
command reception, the nvmet_fc transport occasionally may need to
hold on to the command iu buffer for a short period. In these cases,
the nvmet_fc_rcv_fcp_req() will return a special return code
(-EOVERFLOW). In these cases, the LLDD must delay until the new
defer_rcv lldd callback is called before recycling the buffer back
to the hw.
This patch adds support for the new nvmet_fc transport defer_rcv
callback and recognition of the new error code when passing commands
to the transport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Two small fixes, one re-fix of a previous fix and five patches sorting
out hotplug in the bnx2X class of drivers. The latter is rather
involved, but necessary because these drivers have started dropping
lockdep recursion warnings on the hotplug lock because of its
conversion to a percpu rwsem.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Lg/x
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes, one re-fix of a previous fix and five patches sorting
out hotplug in the bnx2X class of drivers. The latter is rather
involved, but necessary because these drivers have started dropping
lockdep recursion warnings on the hotplug lock because of its
conversion to a percpu rwsem"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sg: only check for dxfer_len greater than 256M
scsi: aacraid: reading out of bounds
scsi: qedf: Limit number of CQs
scsi: bnx2i: Simplify cpu hotplug code
scsi: bnx2fc: Simplify CPU hotplug code
scsi: bnx2i: Prevent recursive cpuhotplug locking
scsi: bnx2fc: Prevent recursive cpuhotplug locking
scsi: bnx2fc: Plug CPU hotplug race
If a SES device returns an error on a requested diagnostic page, we are
currently printing an error indicating the wrong page was received. Fix
this up to simply return a failure and only check the returned page when
the diagnostic page buffer was populated by the device.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If blk_queue_get() in st_probe fails, disk->queue must not be set to
SDp->request_queue, as that would result in put_disk() dropping a not
taken reference.
Thus, disk->queue should be set only after a successful blk_queue_get().
Fixes: 2b5bebccd2 ("st: Take additional queue ref in st_probe")
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Acked-by: Shirish Pargaonkar <spargaonkar@suse.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We need to override Kbuild rules for copying shipped files, otherwise
aic7xxx_reg.h and aic7xxx_reg_print.c will be ovewritten by old versions.
Fixes: 516b7db593
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ahc_platform_dump_card_state() does nothing. Remove it.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Scsi_cmnd is an unsuitable argument for eh_device_reset_handler(),
eh_target_reset_handler(), and eh_host_reset_handler() which do not have
the scope of one single SCSI command. These callbacks tend to use
fc_block_scsi_eh() requiring scsi_cmnd. In order to start decoupling
above eh callbacks from scsi_cmnd, introduce a new variant of the
function called fc_block_rport() taking an fc_rport as argument.
Refactor the old fc_block_scsi_eh() to simply delegate to
fc_block_rport().
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support to the driver to set the exchange threshold value for
the number of outstanding AENs.
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality.
Following cleanups have been done as requested by reviewer
- Changed waitQ --> waitq
- Collapsed multiple debug statements into single
- Remove extra parentheses in if-else as per operator precedence
- Remove unnecessary casting
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dick Kennedy
himanshu.madhani@cavium.com
Sawan Chandak
Giridhar Malavali
Joe Carnuccio
Quinn Tran
Michael Hernandez
Quinn Tran
Duane Grigsby
Darren Trap
Shivasharan S
Gustavo A. R. Silva
Todd Poynor
Dan Carpenter
Arvind Yadav
weiping zhang
Hannes Reinecke
Chad Dupuis
Colin Ian King
Christophe JAILLET
Helge Deller
Richard W.M. Jones
Manish Rangankar
John Garry
Xiang Chen
Linus Torvalds
Brian King
Varun Prakash
Christoph Hellwig
Damien Le Moal
Raghava Aditya Renukunta
Jens Axboe
Xiaofei Tan
Kevin Barnett
Kevin Barnett
Pan Bian
Finn Thain
Bhumika Goyal
Michał Mirosław
James Smart
Bodo Stroesser
Steffen Maier