Commit Graph

220 Commits

Author SHA1 Message Date
Aaron Lu 691e3d3175 [SCSI] sd: update sd to use the new pm callbacks
Update sd driver to use the callbacks defined in dev_pm_ops.

sd_freeze is NULL, the bus level callback has taken care of quiescing
the device so there should be nothing needs to be done here.
Consequently, sd_thaw is not needed here either.

suspend, poweroff and runtime suspend share the same routine sd_suspend,
which will sync flush and then stop the drive, this is the same as before.

resume, restore and runtime resume share the same routine sd_resume,
which will start the drive by putting it into active power state, this
is also the same as before.

Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-11-30 09:28:34 +00:00
Aaron Lu a01475637c [SCSI] sd: put to stopped power state when runtime suspend
When device is runtime suspended, put it to stopped power state to save
some power.

This will also make the behaviour consistent with what the scsi_pm.c
thinks about sd as the comment says:
sd treats runtime suspend, system suspend and system hibernate identical.
With this patch, it is now identical.
And sd_shutdown will also do nothing when it finds the device has been
runtime suspended, if we do not spin down the disk in runtime suspend
by putting it into stopped power state, the disk will be shut down
incorrectly.
And the the same problem can be solved for runtime power off after
runtime suspended case by this change.

With the current runtime scheme for disk, it will only be runtime
suspended when no process opens the disk, so this shouldn't happen a
lot, which makes it acceptable to spin down the disk when runtime
suspended. If some day a more aggressive runtime scheme is used, like
the 'request based runtime pm for disk' that Alan Stern and Lin Ming
has been working, we can introduce some policy to control this. But for
now, make it simple and correct by spinning down the disk.

Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-11-30 09:22:09 +00:00
Jason J. Herne 53ad570be6 [SCSI] sd: Use SCSI read/write(16) with > 32-bit LBA drives
Force large capacity (> 0xFFFFFFFF blocks) drives to use READ/WRITE(16) instead
of READ/WRITE(10). Some(most/all?) USB enclosures do not like READ(10) commands
when a large capacity drive is installed. This issue was reported and discussed
here: http://marc.info/?l=linux-usb&m=135247705222324

Signed-off-by: Jason J. Herne <hernejj@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-11-27 09:00:38 +04:00
Joel D. Diaz afd5e34b2b [SCSI] sd: Reshuffle init_sd to avoid crash
scsi_register_driver will register a prep_fn() function, which
in turn migh need to use the sd_cdp_pool for DIF.
Which hasn't been initialised at this point, leading to
a crash. So reshuffle the init_sd() and exit_sd() paths
to have the driver registered last.

Signed-off-by: Joel D. Diaz <joeldiaz@us.ibm.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-11-27 08:59:34 +04:00
Martin K. Petersen 5db44863b6 [SCSI] sd: Implement support for WRITE SAME
Implement support for WRITE SAME(10) and WRITE SAME(16) in the SCSI disk
driver.

 - We set the default maximum to 0xFFFF because there are several
   devices out there that only support two-byte block counts even with
   WRITE SAME(16). We only enable transfers bigger than 0xFFFF if the
   device explicitly reports MAXIMUM WRITE SAME LENGTH in the BLOCK
   LIMITS VPD.

 - max_write_same_blocks can be overriden per-device basis in sysfs.

 - The UNMAP discovery heuristics remain unchanged but the discard
   limits are tweaked to match the "real" WRITE SAME commands.

 - In the error handling logic we now distinguish between WRITE SAME
   with and without UNMAP set.

The discovery process heuristics are:

 - If the device reports a SCSI level of SPC-3 or greater we'll issue
   READ SUPPORTED OPERATION CODES to find out whether WRITE SAME(16) is
   supported. If that's the case we will use it.

 - If the device supports the block limits VPD and reports a MAXIMUM
   WRITE SAME LENGTH bigger than 0xFFFF we will use WRITE SAME(16).

 - Otherwise we will use WRITE SAME(10) unless the target LBA is beyond
   0xFFFFFFFF or the block count exceeds 0xFFFF.

 - no_write_same is set for ATA, FireWire and USB.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-11-13 22:45:42 -08:00
Martin K. Petersen 26e85fcd15 [SCSI] sd: Permit merged discard requests
Support requests with more than one bio payload for discards. The total
number of bytes to be discarded is stored in req->__data_len and used in
sd_done() to complete the I/O.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-11-13 21:23:53 -08:00
Martin K. Petersen fe542396da [SCSI] sd: Ensure we correctly disable devices with unknown protection type
We set the capacity to zero when we discovered a device formatted with
an unknown DIF protection type. However, the read_capacity code would
override the capacity and cause the device to be enabled regardless.

Make sd_read_protection_type() return an error if the protection type is
unknown. Also prevent duplicate printk lines when the device is being
revalidated.

Reported-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 13:01:24 +04:00
Martin K. Petersen 8172499aae [SCSI] sd: Allow protection_type to be overridden
We have encountered a few devices that misbehaved when operating in T10
PI mode. Allow T10 PI protection type to be overridden from userland.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:10:59 +04:00
Martin K. Petersen 8c579ab69d [SCSI] sd: Avoid remapping bad reference tags
It does not make sense to translate ref tags with unexpected values.
Instead we simply ignore them and let the upper layers catch the
problem. Ref tags that contain the expected value are still remapped.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:10:59 +04:00
Namjae Jeon b81478d82e [SCSI] set to WCE if usb cache quirk is present.
Make use of USB quirk method to identify such HDD while reading
the cache status in sd_probe(). If cache quirk is present for
the HDD, lets assume that cache is enabled and make WCE bit
equal to 1.

Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:59:00 +01:00
Josh Hunt 9e1a15376b [SCSI] properly initialize atomic_t
Initialize atomic_t scsi_host_next_hn and ioerr_cntas per the guidelines
defined in Documentation/atomic_ops.txt

Signed-off-by: Josh Hunt <johunt@akamai.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:36 +01:00
Alan Stern 6a0bdffa00 SCSI & usb-storage: add try_rc_10_first flag
Several bug reports have been received recently for USB mass-storage
devices that don't handle READ CAPACITY(16) commands properly.  They
report bogus sizes, in some cases becoming unusable as a result.

The bugs were triggered by commit
09b6b51b0b (SCSI & usb-storage: add
flags for VPD pages and REPORT LUNS), which caused usb-storage to stop
overriding the SCSI level reported by devices.  By default, the sd
driver will try READ CAPACITY(16) first for any device whose level is
above SCSI_SPC_2.

It seems likely that any device large enough to require the use of
READ CAPACITY(16) (i.e., 2 TB or more) would be able to handle READ
CAPACITY(10) commands properly.  Indeed, I don't know of any devices
that don't handle READ CAPACITY(10) properly.

Therefore this patch (as1559) adds a new flag telling the sd driver
to try READ CAPACITY(10) before READ CAPACITY(16), and sets this flag
for every USB mass-storage device.  If a device really is larger than
2 TB, sd will fall back to READ CAPACITY(16) just as it used to.

This fixes Bugzilla #43391.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
CC: "James E.J. Bottomley" <JBottomley@parallels.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-06-22 22:05:31 -07:00
Dan Williams a7a20d1039 [SCSI] sd: limit the scope of the async probe domain
sd injects and synchronizes probe work on the global kernel-wide domain.
This runs into conflict with PM that wants to perform resume actions in
async context:

[  494.237079] INFO: task kworker/u:3:554 blocked for more than 120 seconds.
[  494.294396] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  494.360809] kworker/u:3     D 0000000000000000     0   554      2 0x00000000
[  494.420739]  ffff88012e4d3af0 0000000000000046 ffff88013200c160 ffff88012e4d3fd8
[  494.484392]  ffff88012e4d3fd8 0000000000012500 ffff8801394ea0b0 ffff88013200c160
[  494.548038]  ffff88012e4d3ae0 00000000000001e3 ffffffff81a249e0 ffff8801321c5398
[  494.611685] Call Trace:
[  494.632649]  [<ffffffff8149dd25>] schedule+0x5a/0x5c
[  494.674687]  [<ffffffff8104b968>] async_synchronize_cookie_domain+0xb6/0x112
[  494.734177]  [<ffffffff810461ff>] ? __init_waitqueue_head+0x50/0x50
[  494.787134]  [<ffffffff8131a224>] ? scsi_remove_target+0x48/0x48
[  494.837900]  [<ffffffff8104b9d9>] async_synchronize_cookie+0x15/0x17
[  494.891567]  [<ffffffff8104ba49>] async_synchronize_full+0x54/0x70  <-- here we wait for async contexts to complete
[  494.943783]  [<ffffffff8104b9f5>] ? async_synchronize_full_domain+0x1a/0x1a
[  495.002547]  [<ffffffffa00114b1>] sd_remove+0x2c/0xa2 [sd_mod]
[  495.051861]  [<ffffffff812fe94f>] __device_release_driver+0x86/0xcf
[  495.104807]  [<ffffffff812fe9bd>] device_release_driver+0x25/0x32  <-- here we take device_lock()

[  853.511341] INFO: task kworker/u:4:549 blocked for more than 120 seconds.
[  853.568693] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  853.635119] kworker/u:4     D ffff88013097b5d0     0   549      2 0x00000000
[  853.695129]  ffff880132773c40 0000000000000046 ffff880130790000 ffff880132773fd8
[  853.758990]  ffff880132773fd8 0000000000012500 ffff88013288a0b0 ffff880130790000
[  853.822796]  0000000000000246 0000000000000040 ffff88013097b5c8 ffff880130790000
[  853.886633] Call Trace:
[  853.907631]  [<ffffffff8149dd25>] schedule+0x5a/0x5c
[  853.949670]  [<ffffffff8149cc44>] __mutex_lock_common+0x220/0x351
[  854.001225]  [<ffffffff81304bd7>] ? device_resume+0x58/0x1c4
[  854.049082]  [<ffffffff81304bd7>] ? device_resume+0x58/0x1c4
[  854.097011]  [<ffffffff8149ce48>] mutex_lock_nested+0x2f/0x36   <-- here we wait for device_lock()
[  854.145591]  [<ffffffff81304bd7>] device_resume+0x58/0x1c4
[  854.192066]  [<ffffffff81304d61>] async_resume+0x1e/0x45
[  854.237019]  [<ffffffff8104bc93>] async_run_entry_fn+0xc6/0x173  <-- ...while running in async context

Provide a 'scsi_sd_probe_domain' so that async probe actions actions can
be flushed without regard for the state of PM, and allow for the resume
path to handle devices that have transitioned from SDEV_QUIESCE to
SDEV_DEL prior to resume.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
[alan: uplevel scsi_sd_probe_domain, clarify scsi_device_resume]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
[jejb: remove unneeded config guards in include file]
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-05-17 09:10:46 +01:00
Linus Torvalds a75ee6ecd4 SCSI updates on 20120331
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iQEcBAABAgAGBQJPdrIWAAoJEDeqqVYsXL0Mny4IAMTzXGOXCykpWhdIe2R8w0Ys
 eIoTJhBKoQWnLTV8cOODtwmtZcoQLeXkZmizZiAJvX6O1tOgueg+W4AFa9grxXGI
 O0d1bSb2ardzU7VZrZSY60Hd4bylMwn4Xv/0dRrQMwTJO0LEeGWsJPV2+2BuXwMB
 lGCNB67oUBXgMOI1jUZQRwx/mBzQ3e/gINjnpZTNKHia7YkX/yVTFISq7htgfDN7
 1wRGxymbHtVap3NbtUO96BUUndAiF5vom+4WNvaQUyPrCc6aoGWjv+J9DQXY/zgv
 AYjujAluK396D6YncGFAWBzYOg9WFbq54v0PRUanjcTTAu5ILs2BxqWdhmnvl14=
 =IH8T
 -----END PGP SIGNATURE-----

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6

Pull SCSI updates from James Bottomley:
 "This is primarily another round of driver updates (lpfc, bfa, fcoe,
  ipr) plus a new ufshcd driver.  There shouldn't be anything
  controversial in here (The final deletion of scsi proc_ops which
  caused some build breakage has been held over until the next merge
  window to give us more time to stabilise it).

  I'm afraid, with me moving continents at exactly the wrong time,
  anything submitted after the merge window opened has been held over to
  the next merge window."

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (63 commits)
  [SCSI] ipr: Driver version 2.5.3
  [SCSI] ipr: Increase alignment boundary of command blocks
  [SCSI] ipr: Increase max concurrent oustanding commands
  [SCSI] ipr: Remove unnecessary memory barriers
  [SCSI] ipr: Remove unnecessary interrupt clearing on new adapters
  [SCSI] ipr: Fix target id allocation re-use problem
  [SCSI] atp870u, mpt2sas, qla4xxx use pci_dev->revision
  [SCSI] fcoe: Drop the rtnl_mutex before calling fcoe_ctlr_link_up
  [SCSI] bfa: Update the driver version to 3.0.23.0
  [SCSI] bfa: BSG and User interface fixes.
  [SCSI] bfa: Fix to avoid vport delete hang on request queue full scenario.
  [SCSI] bfa: Move service parameter programming logic into firmware.
  [SCSI] bfa: Revised Fabric Assigned Address(FAA) feature implementation.
  [SCSI] bfa: Flash controller IOC pll init fixes.
  [SCSI] bfa: Serialize the IOC hw semaphore unlock logic.
  [SCSI] bfa: Modify ISR to process pending completions
  [SCSI] bfa: Add fc host issue lip support
  [SCSI] mpt2sas: remove extraneous sas_log_info messages
  [SCSI] libfc: fcoe_transport_create fails in single-CPU environment
  [SCSI] fcoe: reduce contention for fcoe_rx_list lock [v2]
  ...
2012-03-31 13:31:23 -07:00
Petr Uzel 2db93ce8cc [SCSI] sd: make comment and printk string match code
Adapt comment and printk string after renaming sd_init_command to sd_prep_fn
Adapt comment and printk string after renaming sd_attach to sd_probe

Signed-off-by: Petr Uzel <petr.uzel@suse.cz>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-03-27 08:26:28 +01:00
Linus Torvalds 424a6f6ef9 SCSI updates on 20120319
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iQEcBAABAgAGBQJPZxSnAAoJEDeqqVYsXL0M0Y4IAMX0vrTVZbg6psA5/gMcWGRP
 CkFXEQ8n0PL2SCaj6BoDqamJFe5Nc7dnqxM0fGawB4S9vr3rHhiOlwO+NbV9zFYC
 2skBTpeL3sjgtN/jTBdfeeAa7xTYpu/XGyei0NS1A5c2AyMVXV0uYV2s4VNZxe44
 tVIn1OEzM2giZ9EB1OZslDMrg5XXm3MBIUECP0LbWUhBm/35caSFKzMXRwhh7WiK
 +AVmc2AZYtdEwuknDyiH7KlsaoB3vGL9pPrAUJzIgEhy2pOo2A7W72HfA4Fj+y6a
 uF9HBS5zciMp1+sGWry62AjNbWgin9BRlozBEO/lJhIfMGDV1nXEIJsOkOgkdoE=
 =1TxB
 -----END PGP SIGNATURE-----

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6

SCSI updates from James Bottomley:
 "The update includes the usual assortment of driver updates (lpfc,
  qla2xxx, qla4xxx, bfa, bnx2fc, bnx2i, isci, fcoe, hpsa) plus a huge
  amount of infrastructure work in the SAS library and transport class
  as well as an iSCSI update.  There's also a new SCSI based virtio
  driver."

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (177 commits)
  [SCSI] qla4xxx: Update driver version to 5.02.00-k15
  [SCSI] qla4xxx: trivial cleanup
  [SCSI] qla4xxx: Fix sparse warning
  [SCSI] qla4xxx: Add support for multiple session per host.
  [SCSI] qla4xxx: Export CHAP index as sysfs attribute
  [SCSI] scsi_transport: Export CHAP index as sysfs attribute
  [SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
  [SCSI] iscsi_transport: Add support to display CHAP list and delete CHAP entry
  [SCSI] pm8001: fix endian issue with code optimization.
  [SCSI] pm8001: Fix possible racing condition.
  [SCSI] pm8001: Fix bogus interrupt state flag issue.
  [SCSI] ipr: update PCI ID definitions for new adapters
  [SCSI] qla2xxx: handle default case in qla2x00_request_firmware()
  [SCSI] isci: improvements in driver unloading routine
  [SCSI] isci: improve phy event warnings
  [SCSI] isci: debug, provide state-enum-to-string conversions
  [SCSI] scsi_transport_sas: 'enable' phys on reset
  [SCSI] libsas: don't recover end devices attached to disabled phys
  [SCSI] libsas: fixup target_port_protocols for expanders that don't report sata
  [SCSI] libsas: set attached device type and target protocols for local phys
  ...
2012-03-22 12:55:29 -07:00
Lan Tianyu 4e2247b2bd [SCSI] sd: Add runtime pm in the sd_check_events()
The sd_check_event() will be called periodly even when the device is in the
suspended status to check media event. The scsi_test_unit_ready() in the
sd_check_event() will issue scsi cmd request. Issuing scsi request when the
device is in the suspeneded status will cause problem. For example, when a usb
flash disk in the suspended status, scsi_test_unit_ready() issues a scsi
request. The request will be returned as failed because the usb device is not
active. The patch adds scsi_autopm_get_device() and scsi_autopm_put_device()
around scsi_test_unit_ready() in the sd_check_event() to resolve such problem.

Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-03-19 11:34:18 +00:00
Martin K. Petersen 18a4d0a22e [SCSI] Handle disk devices which can not process medium access commands
We have experienced several devices which fail in a fashion we do not
currently handle gracefully in SCSI. After a failure these devices will
respond to the SCSI primary command set (INQUIRY, TEST UNIT READY, etc.)
but any command accessing the storage medium will time out.

The following patch adds an callback that can be used by upper level
drivers to inspect the results of an error handling command. This in
turn has been used to implement additional checking in the SCSI disk
driver.

If a medium access command fails twice but TEST UNIT READY succeeds both
times in the subsequent error handling we will offline the device. The
maximum number of failed commands required to take a device offline can
be tweaked in sysfs.

Also add a new error flag to scsi_debug which allows this scenario to be
easily reproduced.

[jejb: fix up integer parsing to use kstrtouint]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 10:14:52 -06:00
Martin K. Petersen 89730393f2 [SCSI] sd: Make sure provisioning mode is reported correctly
The provisioning_mode parameter in sysfs did not get updated in the
SD_LBP_DISABLE case. Make sure the provisioning mode is always set
correctly.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 09:39:09 -06:00
Alan Stern 09b6b51b0b SCSI & usb-storage: add flags for VPD pages and REPORT LUNS
This patch (as1507) adds a skip_vpd_pages flag to struct scsi_device
and a no_report_luns flag to struct scsi_target.  The first is used to
control whether sd will look at VPD pages for information on block
provisioning, limits, and characteristics.  The second prevents
scsi_report_lun_scan() from issuing a REPORT LUNS command.

The patch also modifies usb-storage to set the new flag bits for all
USB devices and targets, and to stop adjusting the scsi_level value.

Historically we have seen that USB mass-storage devices often don't
support VPD pages or REPORT LUNS properly.  Until now we have avoided
these things by setting the scsi_level to SCSI_2 for all USB devices.
But this has the side effect of storing the LUN bits into the second
byte of each CDB, and now we have a report of a device which doesn't
like that.  The best solution is to stop abusing scsi_level and
instead have separate flags for VPD pages and REPORT LUNS.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Perry Wagle <wagle@mac.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-08 17:36:41 -08:00
Paolo Bonzini 0bfc96cb77 block: fail SCSI passthrough ioctls on partition devices
Linux allows executing the SG_IO ioctl on a partition or LVM volume, and
will pass the command to the underlying block device.  This is
well-known, but it is also a large security problem when (via Unix
permissions, ACLs, SELinux or a combination thereof) a program or user
needs to be granted access only to part of the disk.

This patch lets partitions forward a small set of harmless ioctls;
others are logged with printk so that we can see which ioctls are
actually sent.  In my tests only CDROM_GET_CAPABILITY actually occurred.
Of course it was being sent to a (partition on a) hard disk, so it would
have failed with ENOTTY and the patch isn't changing anything in
practice.  Still, I'm treating it specially to avoid spamming the logs.

In principle, this restriction should include programs running with
CAP_SYS_RAWIO.  If for example I let a program access /dev/sda2 and
/dev/sdb, it still should not be able to read/write outside the
boundaries of /dev/sda2 independent of the capabilities.  However, for
now programs with CAP_SYS_RAWIO will still be allowed to send the
ioctls.  Their actions will still be logged.

This patch does not affect the non-libata IDE driver.  That driver
however already tests for bd != bd->bd_contains before issuing some
ioctl; it could be restricted further to forbid these ioctls even for
programs running with CAP_SYS_ADMIN/CAP_SYS_RAWIO.

Cc: linux-scsi@vger.kernel.org
Cc: Jens Axboe <axboe@kernel.dk>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[ Make it also print the command name when warning - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-01-14 15:07:24 -08:00
Paolo Bonzini 577ebb374c block: add and use scsi_blk_cmd_ioctl
Introduce a wrapper around scsi_cmd_ioctl that takes a block device.

The function will then be enhanced to detect partition block devices
and, in that case, subject the ioctls to whitelisting.

Cc: linux-scsi@vger.kernel.org
Cc: Jens Axboe <axboe@kernel.dk>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-01-14 15:07:24 -08:00
Lin Ming 54f5758846 [SCSI] sd: check runtime PM status in sd_shutdown
sd_shutdown is called during reboot/poweroff.
It may fail if parent device, for example, ata port, was runtime suspended.

Fix it by checking runtime PM status of sd.
Exit immediately if sd was runtime suspended already.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-01-08 19:14:57 -05:00
Dave Kleikamp 21208ae5a2 [SCSI] sd: remove arbitrary SD_MAX_DISKS namespace limit
There is no reason to limit the SCSI disk namespace to sdXXX.

Add new error messages to sd_probe() in the unlikely event that either
ida_get_new() or sd_format_disk_name() fail.

Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-30 12:58:11 +04:00
Nao Nishijima fe2d1851e9 [SCSI] sd: Use sd_printk() instead of printk()
sd_ioctl() still use printk() for log output.
It should use sd_printk() instead of printk(), as well as other sd_*.

All SCSI messages should output via s*_printk() instead of printk().

Signed-off-by: Nao Nishijima <nao.nishijima.xt@hitachi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-29 00:16:20 -07:00
Luben Tuikov 0bcaa11154 [SCSI] Retrieve the Caching mode page (version 2)
Some kernel transport drivers unconditionally disable
retrieval of the Caching mode page. One such for example is
the BBB/CBI transport over USB. Such a restraint is too
harsh as some devices do support the Caching mode
page. Unconditionally enabling the retrieval of this mode
page over those transports at their transport code level may
result in some devices failing and becoming unusable.

This patch implements a method of retrieving the Caching
mode page without unconditionally enabling it in the
transports which unconditionally disable it. The idea is to
ask for all supported pages, page code 0x3F, and then search
for the Caching mode page in the mode parameter data
returned. The sd driver already asks for all the mode pages
supported by the attached device by setting the page code to
0x3F in order to find out if the media is write protected by
reading the WP bit in the Device Specific Parameter
field. It then attempts to retrieve only the Caching mode
page by setting the page code to 8 and actually attempting
to retrieve it if and only if the transport allows it.

The method implemented here is that if the transport doesn't
allow retrieval of the Caching mode page and the device is
not RBC, then we ask for all pages supported by setting the
page code to 0x3F (similarly to how the WP bit is retrieved
above), and then we search for the Caching mode page in the
mode parameter data returned.

With this patch, devices over SATA, report this (no change):

Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Write Protect is off
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

Smart devices report their Caching mode page. This is a
change where we'd previously see the kernel making
assumption about the device's cache being write-through:

Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: Attached scsi generic sg2 type 0
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] 610472646 4096-byte logical blocks: (2.50 TB/2.27 TiB)
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Write Protect is off
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Mode Sense: 47 00 10 08
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA

And "dumb" devices over BBB, are correctly shown not to
support reporting the Caching mode page:

Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Write Protect is off
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Mode Sense: 23 00 00 00
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] No Caching mode page present
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Assuming drive cache: write through

Version 2 adds this:

Some devices don't support page code 0x3F, and others require a
fixed transfer length of 192 bytes. This single commit includes a
patch by Alan Stern which fixes this.

Reported-and-tested-by: Richard Senior <richard@r-senior.demon.co.uk>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
2011-05-24 12:43:52 -04:00
Martin K. Petersen 2a8cfad06e [SCSI] sd: Unmap discard alignment needs to be converted to bytes
The block layer discard alignment is reported in bytes, not in units of
the logical block size.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
2011-05-24 12:38:15 -04:00
Lucas De Marchi 25985edced Fix common misspellings
Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-31 11:26:23 -03:00
James Bottomley 3dea642afd [SCSI] Revert "[SCSI] Retrieve the Caching mode page"
This reverts commit 24d720b726.

Previously we thought there was little possibility that devices would
crash with this, but some have been found.

Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-03-23 12:53:09 -05:00
Martin K. Petersen 09b9cc44c9 sd: Fail discard requests when logical block provisioning has been disabled
Ensure that we kill discard requests after logical block provisioning
has been disabled in sysfs.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 09:35:53 -07:00
Martin K. Petersen c98a0eb0e9 [SCSI] sd: Logical Block Provisioning update
SBC3r26 contains many changes to the Logical Block Provisioning
interfaces (formerly known as Thin Provisioning ditto). This patch
implements support for both the old and new schemes using the same
heuristic as before (whether the LBP VPD page is present).

The new code also allows the provisioning mode (i.e. choice of command)
to be overridden on a per-device basis via sysfs. Two additional modes
are supported in this version:

 - WRITE SAME(10) with the UNMAP bit set

 - WRITE SAME(10) without the UNMAP bit set. This allows us to support
   devices that predate the TP/LBP enhancements in SBC3 and which work
   by way zero-detection

Switching between modes has been consolidated in a helper function that
also updates the block layer topology according to the limitations of
the chosen command.

I experimented with trying WRITE SAME(16) if UNMAP fails, WRITE SAME(10)
if WRITE SAME(16) fails, etc. but found several devices that got
cranky. So for now we'll disable discard if one of the commands
fail. The user still has the option of selecting a different mode in
sysfs.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-03-14 18:37:34 -05:00
Tejun Heo f4013c3879 [SCSI] sd,sr: kill compat SDEV_MEDIA_CHANGE event
SDEV_MEDIA_CHANGE event was first added by commit a341cd0f (SCSI: add
asynchronous event notification API) for SATA AN support and then
extended to cover generic media change events by commit 285e9670
([SCSI] sr,sd: send media state change modification events).

This event was mapped to block device in userland with all properties
stripped to simulate CHANGE event on the block device, which, in turn,
was used to trigger further userspace action on media change.

The recent addition of disk event framework kept this event for
backward compatibility but it turns out to be unnecessary and causes
erratic and inefficient behavior.  The new disk event generates proper
events on the block devices and the compat events are mapped to block
device with all properties stripped, so the block device ends up
generating multiple duplicate events for single actual event.

This patch removes the compat event generation from both sr and sd as
suggested by Kay Sievers.  Both existing and newer versions of udev
and the associated tools will behave better with the removal of these
events as they from the beginning were expecting events on the block
devices.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-01-14 09:17:35 -06:00
Tejun Heo 2bae0093ca [SCSI] sd: implement sd_check_events()
Replace sd_media_change() with sd_check_events().

* Move media removed logic into set_media_not_present() and
  media_not_present() and set sdev->changed iff an existing media is
  removed or the device indicates UNIT_ATTENTION.

* Make sd_check_events() sets sdev->changed if previously missing
  media becomes present.

* Event is reported only if sdev->changed is set.

This makes media presence event reported if scsi_disk->media_present
actually changed or the device indicated UNIT_ATTENTION.  For backward
compatibility, SDEV_EVT_MEDIA_CHANGE is generated each time
sd_check_events() detects media change event.

[jejb: fix boot failure]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-01-14 09:17:34 -06:00
Linus Torvalds 275220f0fc Merge branch 'for-2.6.38/core' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.38/core' of git://git.kernel.dk/linux-2.6-block: (43 commits)
  block: ensure that completion error gets properly traced
  blktrace: add missing probe argument to block_bio_complete
  block cfq: don't use atomic_t for cfq_group
  block cfq: don't use atomic_t for cfq_queue
  block: trace event block fix unassigned field
  block: add internal hd part table references
  block: fix accounting bug on cross partition merges
  kref: add kref_test_and_get
  bio-integrity: mark kintegrityd_wq highpri and CPU intensive
  block: make kblockd_workqueue smarter
  Revert "sd: implement sd_check_events()"
  block: Clean up exit_io_context() source code.
  Fix compile warnings due to missing removal of a 'ret' variable
  fs/block: type signature of major_to_index(int) to major_to_index(unsigned)
  block: convert !IS_ERR(p) && p to !IS_ERR_NOR_NULL(p)
  cfq-iosched: don't check cfqg in choose_service_tree()
  fs/splice: Pull buf->ops->confirm() from splice_from_pipe actors
  cdrom: export cdrom_check_events()
  sd: implement sd_check_events()
  sr: implement sr_check_events()
  ...
2011-01-13 10:45:01 -08:00
James Bottomley a8733c7baf [SCSI] fix medium error problems with some arrays which can cause data corruption
Our current handling of medium error assumes that data is returned up
to the bad sector.  This assumption holds good for all disk devices,
all DIF arrays and most ordinary arrays.  However, an LSI array engine
was recently discovered which reports a medium error without returning
any data.  This means that when we report good data up to the medium
error, we've reported junk originally in the buffer as good.  Worse,
if the read consists of requested data plus a readahead, and the error
occurs in readahead, we'll just strip off the readahead and report
junk up to userspace as good data with no error.

The fix for this is to have the error position computation take into
account the amount of data returned by the driver using the scsi
residual data.  Unfortunately, not every driver fills in this data,
but for those who don't, it's set to zero, which means we'll think a
full set of data was transferred and the behaviour will be identical
to the prior behaviour of the code (believe the buffer up to the error
sector).  All modern drivers seem to set the residual, so that should
fix up the LSI failure/corruption case.

Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-12-22 23:26:48 -06:00
Jens Axboe fcc57045d5 Revert "sd: implement sd_check_events()"
This reverts commit c8d2e93735.

We run into merging problems with the SCSI tree, revert this one
so it can be handled by a postmerge tree there.

Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2010-12-22 09:48:49 +01:00
Luben Tuikov 24d720b726 [SCSI] Retrieve the Caching mode page
Some kernel transport drivers unconditionally disable
retrieval of the Caching mode page. One such for example is
the BBB/CBI transport over USB.  Such a restraint is too
harsh as some devices do support the Caching mode
page. Unconditionally enabling the retrieval of this mode
page over those transports at their transport code level may
result in some devices failing and becoming unusable.

This patch implements a method of retrieving the Caching
mode page without unconditionally enabling it in the
transports which unconditionally disable it. The idea is to
ask for all supported pages, page code 0x3F, and then search
for the Caching mode page in the mode parameter data
returned. The sd driver already asks for all the mode pages
supported by the attached device by setting the page code to
0x3F in order to find out if the media is write protected by
reading the WP bit in the Device Specific Parameter
field. It then attempts to retrieve only the Caching mode
page by setting the page code to 8 and actually attempting
to retrieve it if and only if the transport allows it.

The method implemented here is that if the transport doesn't
allow retrieval of the Caching mode page and the device is
not RBC, then we ask for all pages supported by setting the
page code to 0x3F (similarly to how the WP bit is retrieved
above), and then we search for the Caching mode page in the
mode parameter data returned.

With this patch, devices over SATA, report this (no change):

Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Write Protect is off
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

Smart devices report their Caching mode page. This is a
change where we'd previously see the kernel making
assumption about the device's cache being write-through:

Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: Attached scsi generic sg2 type 0
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] 610472646 4096-byte logical blocks: (2.50 TB/2.27 TiB)
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Write Protect is off
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Mode Sense: 47 00 10 08
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA

And "dumb" devices over BBB, are correctly shown not to
support reporting the Caching mode page:

Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Write Protect is off
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Mode Sense: 23 00 00 00
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] No Caching mode page present
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Assuming drive cache: write through

Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-12-21 12:23:53 -06:00
Alan Stern 3ff5588d3f [SCSI] sd: improve logic and efficiecy of media-change detection
This patch (as1415) improves the formerly incomprehensible logic in
sd_media_changed() (the current code refers to "changed" as a state,
whereas in fact it is a relation between two states).  It also adds a
big comment so that everyone can understand what is really going on.

The patch also improves efficiency by not reporting a media change
when no medium was ever present.  If no medium was present the last
time we checked and there's still no medium, it's not necessary to
tell the caller that a change occurred.  Doing so merely causes the
caller to attempt to revalidate a non-existent disk, which is a waste
of time.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-12-21 12:23:52 -06:00
Tejun Heo c8d2e93735 sd: implement sd_check_events()
Replace sd_media_change() with sd_check_events().  sd used to set the
changed state whenever the device is not ready, which can cause event
loop while the device is not ready.  Media presence handling code is
changed such that the changed state is set iff the media presence
actually changes.  UA still always sets the changed state and
NOT_READY always (at least where it used to set ->changed) clears
media presence, so no event is lost.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2010-12-16 17:53:39 +01:00
Tejun Heo 9f8a2c23c6 scsi: replace sr_test_unit_ready() with scsi_test_unit_ready()
The usage of TUR has been confusing involving several different
commits updating different parts over time.  Currently, the only
differences between scsi_test_unit_ready() and sr_test_unit_ready()
are,

* scsi_test_unit_ready() also sets sdev->changed on NOT_READY.

* scsi_test_unit_ready() returns 0 if TUR ended with UNIT_ATTENTION or
  NOT_READY.

Due to the above two differences, sr is using its own
sr_test_unit_ready(), but sd - the sole user of the above extra
handling - doesn't even need them.

Where scsi_test_unit_ready() is used in sd_media_changed(), the code
is looking for device ready w/ media present state which is true iff
TUR succeeds w/o sense data or UA, and when the device is not ready
for whatever reason sd_media_changed() explicitly marks media as
missing so there's no reason to set sdev->changed automatically from
scsi_test_unit_ready() on NOT_READY.

Drop both special handlings from scsi_test_unit_ready(), which makes
it equivalant to sr_test_unit_ready(), and replace
sr_test_unit_ready() with scsi_test_unit_ready().  Also, drop the
unnecessary explicit NOT_READY check from sd_media_changed().
Checking return value is enough for testing device readiness.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2010-12-16 17:53:39 +01:00
Arnd Bergmann 451a3c24b0 BKL: remove extraneous #include <smp_lock.h>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.

Remove this too as a cleanup.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-11-17 08:59:32 -08:00
Martin K. Petersen 518fa8e39b [SCSI] sd: Export effective protection mode in sysfs
Create a sysfs entry that reports the negotiated DIX/DIF protection mode
for a SCSI disk. This depends on the protection type the disk is
formatted with as well as the protection capabilities advertised by the
controller.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-25 14:57:44 -05:00
Linus Torvalds 5cc1035062 Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (141 commits)
  USB: mct_u232: fix broken close
  USB: gadget: amd5536udc.c: fix error path
  USB: imx21-hcd - fix off by one resource size calculation
  usb: gadget: fix Kconfig warning
  usb: r8a66597-udc: Add processing when USB was removed.
  mxc_udc: add workaround for ENGcm09152 for i.MX35
  USB: ftdi_sio: add device ids for ScienceScope
  USB: musb: AM35x: Workaround for fifo read issue
  USB: musb: add musb support for AM35x
  USB: AM35x: Add musb support
  usb: Fix linker errors with CONFIG_PM=n
  USB: ohci-sh - use resource_size instead of defining its own resource_len macro
  USB: isp1362-hcd - use resource_size instead of defining its own resource_len macro
  USB: isp116x-hcd - use resource_size instead of defining its own resource_len macro
  USB: xhci: Fix compile error when CONFIG_PM=n
  USB: accept some invalid ep0-maxpacket values
  USB: xHCI: PCI power management implementation
  USB: xHCI: bus power management implementation
  USB: xHCI: port remote wakeup implementation
  USB: xHCI: port power management implementation
  ...

Manually fix up (non-data) conflict: the SCSI merge gad renamed the
'hw_sector_size' member to 'physical_block_size', and the USB tree
brought a new use of it.
2010-10-22 20:30:48 -07:00
Linus Torvalds c70b5296e7 Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (84 commits)
  [SCSI] be2iscsi: SGE Len == 64K
  [SCSI] be2iscsi: Remove premature free of cid
  [SCSI] be2iscsi: More time for FW
  [SCSI] libsas: fix bug for vacant phy
  [SCSI] sd: Fix overflow with big physical blocks
  [SCSI] st: add MTWEOFI to write filemarks without flushing drive buffer
  [SCSI] libsas: Don't issue commands to devices that have been hot-removed
  [SCSI] megaraid_sas: Add Online Controller Reset to MegaRAID SAS drive
  [SCSI] lpfc 8.3.17: Update lpfc driver version to 8.3.17
  [SCSI] lpfc 8.3.17: Replace function reset methodology
  [SCSI] lpfc 8.3.17: SCSI fixes
  [SCSI] lpfc 8.3.17: BSG fixes
  [SCSI] lpfc 8.3.17: SLI Additions and Fixes
  [SCSI] lpfc 8.3.17: Code Cleanup and Locking fixes
  [SCSI] zfcp: Remove scsi_cmnd->serial_number from debug traces
  [SCSI] ipr: fix array error logging
  [SCSI] aha152x: enable PCMCIA on 64bit
  [SCSI] scsi_dh_alua: Handle all states correctly
  [SCSI] cxgb4i: connection and ddp setting update
  [SCSI] cxgb3i: fixed connection over vlan
  ...
2010-10-22 17:34:15 -07:00
Hans de Goede 5ce524bdff scsi/sd: add a no_read_capacity_16 scsi_device flag
I seem to have a knack for digging up buggy usb devices which don't work
with Linux, and I'm crazy enough to try to make them work.  So this time a
friend of mine asked me to get an mp4 player (an mp3 player which can play
videos on a small screen) to work with Linux.

It is based on the well known rockbox chipset for which we already have an
unusual devs entries to work around some of its bugs.  But this model
comes with an additional twist.

This model chokes on read_capacity_16 calls.  Now normally we don't make
those calls, but this model comes with an sdcard slot and when there is no
card in there (and shipped from the factory there is none), it reports a
size of 0.  However this time the programmers actually got the
read_capacity_10 response right!  So they substract one from the size as
stored internally in the mp3 player before reporting it back, resulting in
an answer of ...  0xffffffff sectors, causing sd.c to try a
read_capacity_16, on which the device crashes.

This patch adds a flag to scsi_device to indicate that a a device cannot
handle read_capacity_16, and when this flag is set if a device reports an
lba of 0xffffffff as answer to a read_capacity_10, assumes it tries to
report a size of 0.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22 10:22:05 -07:00
Jens Axboe fa251f8990 Merge branch 'v2.6.36-rc8' into for-2.6.37/barrier
Conflicts:
	block/blk-core.c
	drivers/block/loop.c
	mm/swapfile.c

Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2010-10-19 09:13:04 +02:00
Martin K. Petersen 526f7c7950 [SCSI] sd: Fix overflow with big physical blocks
The hw_sector_size variable could overflow if a device reported huge
physical blocks.  Switch to the more accurate physical_block_size
terminology and make sure we use an unsigned int to match the range
permitted by READ CAPACITY(16).

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-11 17:33:20 -05:00
Michael Reed 1a03ae0f55 [SCSI] sd name space exhaustion causes system hang
Following a site power outage which re-enabled all the ports on my FC
switches, my system subsequently booted with far too many luns!  I had
let it run hoping it would make multi-user.  It didn't.  :(  It hung solid
after exhausting the last sd device, sdzzz, and attempting to create sdaaaa
and beyond.  I was unable to get a dump.

Discovered using a 2.6.32.13 based system.

correct this by detecting when the last index is utilized and failing
the sd probe of the device.  Patch applies to scsi-misc-2.6.

Signed-off-by: Michael Reed <mdr@sgi.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-07 17:16:28 -05:00
Martin K. Petersen 045d3fe766 [SCSI] sd: Update thin provisioning support
Add support for the Thin Provisioning VPD page and use the TPU and TPWS
bits to switch between UNMAP and WRITE SAME(16) for discards.  If no TP
VPD page is present we fall back to old scheme where the max descriptor
count combined with the max lba count are used trigger UNMAP.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-09-17 13:07:55 -04:00
Tejun Heo 4913efe456 block: deprecate barrier and replace blk_queue_ordered() with blk_queue_flush()
Barrier is deemed too heavy and will soon be replaced by FLUSH/FUA
requests.  Deprecate barrier.  All REQ_HARDBARRIERs are failed with
-EOPNOTSUPP and blk_queue_ordered() is replaced with simpler
blk_queue_flush().

blk_queue_flush() takes combinations of REQ_FLUSH and FUA.  If a
device has write cache and can flush it, it should set REQ_FLUSH.  If
the device can handle FUA writes, it should also set REQ_FUA.

All blk_queue_ordered() users are converted.

* ORDERED_DRAIN is mapped to 0 which is the default value.
* ORDERED_DRAIN_FLUSH is mapped to REQ_FLUSH.
* ORDERED_DRAIN_FLUSH_FUA is mapped to REQ_FLUSH | REQ_FUA.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2010-09-10 12:35:36 +02:00