Commit Graph

24 Commits

Author SHA1 Message Date
Martin K. Petersen 5db44863b6 [SCSI] sd: Implement support for WRITE SAME
Implement support for WRITE SAME(10) and WRITE SAME(16) in the SCSI disk
driver.

 - We set the default maximum to 0xFFFF because there are several
   devices out there that only support two-byte block counts even with
   WRITE SAME(16). We only enable transfers bigger than 0xFFFF if the
   device explicitly reports MAXIMUM WRITE SAME LENGTH in the BLOCK
   LIMITS VPD.

 - max_write_same_blocks can be overriden per-device basis in sysfs.

 - The UNMAP discovery heuristics remain unchanged but the discard
   limits are tweaked to match the "real" WRITE SAME commands.

 - In the error handling logic we now distinguish between WRITE SAME
   with and without UNMAP set.

The discovery process heuristics are:

 - If the device reports a SCSI level of SPC-3 or greater we'll issue
   READ SUPPORTED OPERATION CODES to find out whether WRITE SAME(16) is
   supported. If that's the case we will use it.

 - If the device supports the block limits VPD and reports a MAXIMUM
   WRITE SAME LENGTH bigger than 0xFFFF we will use WRITE SAME(16).

 - Otherwise we will use WRITE SAME(10) unless the target LBA is beyond
   0xFFFFFFFF or the block count exceeds 0xFFFF.

 - no_write_same is set for ATA, FireWire and USB.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-11-13 22:45:42 -08:00
Martin K. Petersen 8c579ab69d [SCSI] sd: Avoid remapping bad reference tags
It does not make sense to translate ref tags with unexpected values.
Instead we simply ignore them and let the upper layers catch the
problem. Ref tags that contain the expected value are still remapped.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:10:59 +04:00
Martin K. Petersen 18a4d0a22e [SCSI] Handle disk devices which can not process medium access commands
We have experienced several devices which fail in a fashion we do not
currently handle gracefully in SCSI. After a failure these devices will
respond to the SCSI primary command set (INQUIRY, TEST UNIT READY, etc.)
but any command accessing the storage medium will time out.

The following patch adds an callback that can be used by upper level
drivers to inspect the results of an error handling command. This in
turn has been used to implement additional checking in the SCSI disk
driver.

If a medium access command fails twice but TEST UNIT READY succeeds both
times in the subsequent error handling we will offline the device. The
maximum number of failed commands required to take a device offline can
be tweaked in sysfs.

Also add a new error flag to scsi_debug which allows this scenario to be
easily reproduced.

[jejb: fix up integer parsing to use kstrtouint]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 10:14:52 -06:00
Dave Kleikamp 21208ae5a2 [SCSI] sd: remove arbitrary SD_MAX_DISKS namespace limit
There is no reason to limit the SCSI disk namespace to sdXXX.

Add new error messages to sd_probe() in the unlikely event that either
ida_get_new() or sd_format_disk_name() fail.

Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-30 12:58:11 +04:00
Martin K. Petersen c98a0eb0e9 [SCSI] sd: Logical Block Provisioning update
SBC3r26 contains many changes to the Logical Block Provisioning
interfaces (formerly known as Thin Provisioning ditto). This patch
implements support for both the old and new schemes using the same
heuristic as before (whether the LBP VPD page is present).

The new code also allows the provisioning mode (i.e. choice of command)
to be overridden on a per-device basis via sysfs. Two additional modes
are supported in this version:

 - WRITE SAME(10) with the UNMAP bit set

 - WRITE SAME(10) without the UNMAP bit set. This allows us to support
   devices that predate the TP/LBP enhancements in SBC3 and which work
   by way zero-detection

Switching between modes has been consolidated in a helper function that
also updates the block layer topology according to the limitations of
the chosen command.

I experimented with trying WRITE SAME(16) if UNMAP fails, WRITE SAME(10)
if WRITE SAME(16) fails, etc. but found several devices that got
cranky. So for now we'll disable discard if one of the commands
fail. The user still has the option of selecting a different mode in
sysfs.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-03-14 18:37:34 -05:00
Tejun Heo 2bae0093ca [SCSI] sd: implement sd_check_events()
Replace sd_media_change() with sd_check_events().

* Move media removed logic into set_media_not_present() and
  media_not_present() and set sdev->changed iff an existing media is
  removed or the device indicates UNIT_ATTENTION.

* Make sd_check_events() sets sdev->changed if previously missing
  media becomes present.

* Event is reported only if sdev->changed is set.

This makes media presence event reported if scsi_disk->media_present
actually changed or the device indicated UNIT_ATTENTION.  For backward
compatibility, SDEV_EVT_MEDIA_CHANGE is generated each time
sd_check_events() detects media change event.

[jejb: fix boot failure]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-01-14 09:17:34 -06:00
Martin K. Petersen 526f7c7950 [SCSI] sd: Fix overflow with big physical blocks
The hw_sector_size variable could overflow if a device reported huge
physical blocks.  Switch to the more accurate physical_block_size
terminology and make sure we use an unsigned int to match the range
permitted by READ CAPACITY(16).

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-11 17:33:20 -05:00
Martin K. Petersen 045d3fe766 [SCSI] sd: Update thin provisioning support
Add support for the Thin Provisioning VPD page and use the TPU and TPWS
bits to switch between UNMAP and WRITE SAME(16) for discards.  If no TP
VPD page is present we fall back to old scheme where the max descriptor
count combined with the max lba count are used trigger UNMAP.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-09-17 13:07:55 -04:00
Mike Christie e3b3e62467 [SCSI] scsi/block: increase flush/sync timeout
We have been seeing the flush request timeout with a wide
range of hardware from tgt+iser to FC targets from a major vendor.

After discussions about if the value should be configurable and
what the best value should be, this patch just increases the flush/sync
cache timeout to 1 minute. 2 minutes was determined to be too long, and
making it configurable was troublesome for users.

This patch was made over Linus's tree. It is not made over scsi-misc
or scsi-rc-fixes, because Linus's had block layer changes that my
patch was built over.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-09-05 14:57:04 -03:00
Arnd Bergmann 409f3499a2 scsi/sd: remove big kernel lock
Every user of the BKL in the sd driver is the
result of the pushdown from the block layer
into the open/close/ioctl functions.

The only place that used to rely on the BKL is
the sdkp->openers variable, which gets converted
into an atomic_t.

Nothing else seems to rely on the BKL, since the
functions do not touch global data without holding
another lock, and the open/close functions are
still protected from concurrent execution using
the bdev->bd_mutex.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-scsi@vger.kernel.org
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2010-08-07 18:26:08 +02:00
Martin K. Petersen e339c1a7c0 [SCSI] sd: WRITE SAME(16) / UNMAP support
Implement a function for handling discard requests that sends either
WRITE SAME(16) or UNMAP(10) depending on parameters indicated by the
device in the block limits VPD.

Extract unmap constraints and report them to the block layer.

Based in part by a patch by Christoph Hellwig <hch@lst.de>.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-12-10 08:54:15 -06:00
Martin K. Petersen 4e7392ec58 [SCSI] sd: Support disks formatted with DIF Type 2
Disks formatted with DIF Type 2 reject READ/WRITE 6/10/12/16 commands
when protection is enabled.  Only the 32-byte variants are supported.

Implement support for issusing 32-byte READ/WRITE and enable Type 2
drives in the protection type detection logic.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-10-02 09:47:04 -05:00
Martin K. Petersen 35e1a5d90b [SCSI] sd: Detach DIF from block integrity infrastructure
So far we have only issued DIF commands if CONFIG_BLK_DEV_INTEGRITY is
enabled.  However, communication between initiator and target should be
independent of protection information DMA.  There are DIF-only host
adapters coming out that will be able to take advantage of this.

Move the relevant DIF bits to sd.c.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-10-02 09:46:39 -05:00
Martin K. Petersen ea09bcc9c2 sd: Physical block size and alignment support
Extract physical block size and lowest aligned LBA from READ
CAPACITY(16) response and adjust queue parameters.

Report physical block size and alignment when applicable.

[jejb: fix up trailing whitespace]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-21 10:52:37 -05:00
Martin K. Petersen 70a9b87346 [SCSI] sd: Make revalidate less chatty
sd_revalidate ends up being called several times during device setup.
With this patch we print everything during the first scan.  Subsequent
invocations will only print a message if the parameter in question has
actually changed (LUN capacity has increased, etc.).

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-03-17 21:43:52 -04:00
James Bottomley 4c393e6e45 [SCSI] sd: fix compile failure with CONFIG_BLK_DEV_INTEGRITY=n
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-10-15 08:41:28 -04:00
Martin K. Petersen 9e06688e7d [SCSI] sd: Correctly handle all combinations of DIF and DIX
The old detection code couldn't handle all possible combinations of
DIX and DIF.  This version does, giving priority to DIX if the
controller is capable.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-10-13 09:28:58 -04:00
Linus Torvalds 18351070b8 Re-introduce "[SCSI] extend the last_sector_bug flag to cover more sectors"
This re-introduces commit 2b14290078,
which was reverted due to the regression it caused by commit
fca082c9f1.

That regression was not root-caused by the original commit, it was just
uncovered by it, and the real fix was done by Alan Stern in commit
580da34847 ("Fix USB storage hang on
command abort").

We can thus re-introduce the change that was confirmed by Alan Jenkins
to be still required by his odd card reader.

Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-08-05 21:42:21 -07:00
Linus Torvalds fca082c9f1 Revert "[SCSI] extend the last_sector_bug flag to cover more sectors"
This reverts commit 2b14290078, since it
seems to break some other USB storage devices (at least a JMicron USB to
ATA bridge).  As such, while it apparently fixes some cardreaders, it
would need to be made conditional on the exact reader it fixes in order
to avoid causing regressions.

Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-08-04 16:36:20 -07:00
Alan Jenkins 2b14290078 [SCSI] extend the last_sector_bug flag to cover more sectors
The last_sector_bug flag was added to work around a bug in certain usb
cardreaders, where they would crash if a multiple sector read included the
last sector. The original implementation avoids this by e.g. splitting an 8
sector read which includes the last sector into a 7 sector read, and a single
sector read for the last sector.  The flag is enabled for all USB devices.

This revealed a second bug in other usb cardreaders, which crash when they
get a multiple sector read which stops 1 sector short of the last sector.
Affected hardware includes the Kingston "MobileLite" external USB cardreader
and the internal USB cardreader on the Asus EeePC.

Extend the last_sector_bug workaround to ensure that any access which touches
the last 8 hardware sectors of the device is a single sector long.  Requests
are shrunk as necessary to meet this constraint.

This gives us a safety margin against potential unknown or future bugs
affecting multi-sector access to the end of the device.  The two known bugs
only affect the last 2 sectors.  However, they suggest that these devices
are prone to fencepost errors and that multi-sector access to the end of the
device is not well tested.  Popular OS's use multi-sector accesses, but they
rarely read the last few sectors.  Linux (with udev & vol_id) automatically
reads sectors from the end of the device on insertion.  It is assumed that
single sector accesses are more thoroughly tested during development.

Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-27 10:16:13 -04:00
Martin K. Petersen af55ff675a [SCSI] sd: Support for SCSI disk (SBC) Data Integrity Field
Support for controllers and disks that implement DIF protection
information:

 - During command preparation the RDPROTECT/WRPROTECT must be set
   correctly if the target has DIF enabled.

 - READ(6) and WRITE(6) are not supported when DIF is on.

 - The controller must be told how to handle the I/O via the
   protection operation field in scsi_cmnd.

 - Refactor the I/O completion code that extracts failed LBA from the
   returned sense data and handle DIF failures correctly.

 - sd_dif.c implements the functions required to prepare and complete
   requests with protection information attached.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-26 15:14:56 -04:00
Martin K. Petersen e0597d7001 [SCSI] sd: Identify DIF protection type and application tag ownership
If a disk is formatted with protection information (Inquiry bit
PROTECT=1) it is required to support Read Capacity(16).  Force use of
the 16-bit command in this case and extract the P_TYPE field which
indicates whether the disk is formatted using DIF Type 1, 2 or 3.

The ATO (App Tag Own) bit in the Control Mode Page indicates whether
the storage device or the initiator own the contents of the
DIF application tag.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-26 15:14:55 -04:00
Martin K. Petersen 5b635da11e [SCSI] sd: Move scsi_disk() accessor function to sd.h
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-12 08:22:31 -05:00
Martin K. Petersen aa91696e56 [SCSI] sd: Move sd.h header file
Christoph objected to having sd.h in include/scsi since it is internal
to the sd driver.  Move it to drivers/scsi/sd.h.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-12 08:22:31 -05:00