[ Upstream commit 9b1b0cb0636166187478ef68d5b95f5caea062ec ]
This is supposed to return negative error codes but the type is bool so
it returns true instead.
Fixes: b47b79d8a2 ("[media] media: i2c: max2175: Add MAX2175 support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eeb76afbe8d91e112396c6281cd020725160f006 ]
Stop video streaming when requested.
When s_stream is called to stop the video streaming, if/else condition calls
start_streaming function instead of the one for stopping it.
Fixes: 4361905962 ("media: imx214: Add imx214 camera sensor driver")
Signed-off-by: Daniel Gomez <daniel@qtec.com>
Signed-off-by: Ricardo Ribalda <ribalda@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49b20d981d ]
1) the numerator and/or denominator might be 0, in that case
fall back to the default frame interval. This is per the spec
and this caused a v4l2-compliance failure.
2) the updated frame interval wasn't returned in the s_frame_interval
subdev op.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 877cb8a444 ]
tc358743_cec_isr is misnammed, it is not the main isr.
So rename it to be consistent with its siblings,
tc358743_cec_handler.
It also does not check if its input parameter 'handled' is
is non NULL like its siblings, so add a check.
Fixes: a0ec8d1dc4 ("media: tc358743: add CEC support")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 576f5d4ba8 ]
During testing this sensor on iW-RainboW-G21D-Qseven platform in 8-bit DVP
mode with rcar-vin bridge noticed the capture worked fine for the first run
(with yavta), but for subsequent runs the bridge driver waited for the
frame to be captured. Debugging further noticed the data lines were
enabled/disabled in stream on/off callback and dumping the register
contents 0x3017/0x3018 in ov5640_set_stream_dvp() reported the correct
values, but yet frame capturing failed.
To get around this issue data lines are enabled in s_power callback.
(Also the sensor remains in power down mode if not streaming so power
consumption shouldn't be affected)
Fixes: f22996db44 ("media: ov5640: add support of DVP parallel interface")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b987d70e9 ]
Keep the sensor in software power down mode and wake up only in
ov5640_set_stream_dvp() callback.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52438c4463 ]
clang static analysis reports this error
m5mols_core.c:767:4: warning: Called function pointer
is null (null dereference) [core.CallAndMessage]
info->set_power(&client->dev, 0);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In other places, the set_power ptr is checked.
So add a check.
Fixes: bc125106f8 ("[media] Add support for M-5MOLS 8 Mega Pixel camera ISP")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c85f628f6 ]
Although the code is correct and doing the right thing, the clock diagram
showed the wrong register for the bit divider, which had me doubting the
understanding of the tree. Fix this to avoid doubts in the future.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Fixes: aa2882481c ("media: ov5640: Adjust the clock based on the expected rate")
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5b1d54135 ]
If NVM reading failed, the device was left powered on. Fix that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bfcba38d95 upstream.
v4l2_ctrl_handler_free() uses hdl->lock, which in ov5640 driver is set
to sensor's own sensor->lock. In ov5640_remove(), the driver destroys the
sensor->lock first, and then calls v4l2_ctrl_handler_free(), resulting
in the use of the destroyed mutex.
Fix this by calling moving the mutex_destroy() to the end of the cleanup
sequence, as there's no need to destroy the mutex as early as possible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org # v4.14+
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f1a64f5666 ]
From the measured hardware signal, OV5695 reset pin goes high for a
short period of time during boot-up. From the sensor specification, the
reset pin is active low and the DT binding defines the pin as active
low, which means that the values set by the driver are inverted and thus
the value requested in probe ends up high.
Fix it by changing probe to request the reset GPIO initialized to high,
which makes the initial state of the physical signal low.
In addition, DOVDD rising must occur before DVDD rising from spec., but
regulator_bulk_enable() API enables all the regulators asynchronously.
Use an explicit loops of regulator_enable() instead.
For power off sequence, it is required that DVDD falls first. Given the
bulk API does not give any guarantee about the order of regulators,
change the driver to use regulator_disable() instead.
The sensor also requires a delay between reset high and first I2C
transaction, which was assumed to be 8192 XVCLK cycles, but 1ms is
recommended by the vendor. Fix this as well.
Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64d4fc9926 ]
Fix build fault when CONFIG_HWMON is a module, and CONFIG_VIDEO_I2C
as builtin. This is due to 'imply hwmon' in the respective Kconfig.
Issue build log:
ld: drivers/media/i2c/video-i2c.o: in function `amg88xx_hwmon_init':
video-i2c.c:(.text+0x2e1): undefined reference to `devm_hwmon_device_register_with_info
Cc: rdunlap@infradead.org
Fixes: acbea67989 (media: video-i2c: add hwmon support for amg88xx)
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1451d5ae35 ]
This driver supports both the mt9v032 (color) and the mt9v022 (mono)
sensors. Depending on which sensor is used, the format from the sensor is
different. The format.code inside the dev struct holds this information.
The enum mbus and enum frame sizes need to take into account both type of
sensors, not just the color one. To solve this, use the format.code in
these functions instead of the hardcoded bayer color format (which is only
used for mt9v032).
[Sakari Ailus: rewrapped commit message]
Suggested-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e3df204f9 ]
The variable _rate is by ov5640_compute_sys_clk() which returns
zero if the PLL exceeds 1GHz. Unfortunately, the check to see
if the max PLL1 output is checking 'rate' and not '_rate' and
'rate' does not ever appear to be 0.
This patch changes the check against the returned value of
'_rate' to determine if the PLL1 output exceeds 1GHz.
Fixes: aa2882481c ("media: ov5640: Adjust the clock based on the expected rate")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0d962e061a upstream.
Enclose multiple macro parameters in parentheses in order to
make such macros safer and fix the Clang warning below:
drivers/media/i2c/adv748x/adv748x-afe.c:452:12: warning: operator '?:'
has lower precedence than '|'; '|' will be evaluated first
[-Wbitwise-conditional-parentheses]
ret = sdp_clrset(state, ADV748X_SDP_FRP, ADV748X_SDP_FRP_MASK, enable
? ctrl->val - 1 : 0);
Fixes: 3e89586a64 ("media: i2c: adv748x: add adv748x driver")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5439fa9263 upstream.
It is not clear what pixel format is actually configured in hardware on
reset. MEDIA_BUS_FMT_YUYV8_2X8, assumed on device probe since the
driver was intiially submitted, is for sure not the one.
Fix it by explicitly applying a known, driver default frame format just
after initial device reset.
Fixes: 2f6e240479 ("[media] SoC Camera: add driver for OV6650 sensor")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39034bb0c2 upstream.
Commit da298c6d98 ("[media] v4l2: replace video op g_mbus_fmt by pad
op get_fmt") converted a former ov6650_g_fmt() video operation callback
to an ov6650_get_fmt() pad operation callback. However, the converted
function disregards a format->which flag that pad operations should
obey and always returns active frame format settings.
That can be fixed by always responding to V4L2_SUBDEV_FORMAT_TRY with
-EINVAL, or providing the response from a pad config argument, likely
updated by a former user call to V4L2_SUBDEV_FORMAT_TRY .set_fmt().
Since implementation of the latter is trivial, go for it.
Fixes: da298c6d98 ("[media] v4l2: replace video op g_mbus_fmt by pad op get_fmt")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c6a2b6309 upstream.
User arguments passed to .get/set_fmt() pad operation callbacks may
contain unsupported values. The driver takes control over frame size
and pixel code as well as colorspace and field attributes but has never
cared for remainig format attributes, i.e., ycbcr_enc, quantization
and xfer_func, introduced by commit 11ff030c73 ("[media]
v4l2-mediabus: improve colorspace support"). Fix it.
Set up a static v4l2_mbus_framefmt structure with attributes
initialized to reasonable defaults and use it for updating content of
user provided arguments. In case of V4L2_SUBDEV_FORMAT_ACTIVE,
postpone frame size update, now performed from inside ov6650_s_fmt()
helper, util the user argument is first updated in ov6650_set_fmt() with
default frame format content. For V4L2_SUBDEV_FORMAT_TRY, don't copy
all attributes to pad config, only those handled by the driver, then
fill the response with the default frame format updated with resulting
pad config format code and frame size.
Fixes: 11ff030c73 ("[media] v4l2-mediabus: improve colorspace support")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1250073189 upstream.
Since its initial submission, the driver selects V4L2_COLORSPACE_JPEG
for supported formats other than V4L2_MBUS_FMT_SBGGR8_1X8. According
to v4l2-compliance test program, V4L2_COLORSPACE_JPEG applies
exclusively to V4L2_PIX_FMT_JPEG. Since the sensor does not support
JPEG format, fix it to always select V4L2_COLORSPACE_SRGB.
Fixes: 2f6e240479 ("[media] SoC Camera: add driver for OV6650 sensor")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 90c9e4a4db ]
Earlier it was possible that the parts of the driver that assumed runtime
PM was enabled were being called before runtime PM was enabled in the
driver's probe function. So enable runtime PM before registering the
sub-device.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61c03b631b ]
mipid02_probe misses a check for devm_gpiod_get_optional and may miss
the failure.
Add a check to fix the problem.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 981e445454 ]
The sensor data sheet clearly state that 2592x1944 only works at 15 fps
make sure we don't try to miss configure the pll out of acceptable
range.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57822068dd ]
The driver stores a frame interval value supposed to be in line with
hardware state in a device private structure. Since the driver initial
submission, the respective field of the structure has never been
initialised on device probe. Moreover, if updated from
.s_frame_interval(), a new value is stored before it is applied on
hardware. If an error occurs during device update, the stored value
may no longer reflect hardware state and consecutive calls to
.g_frame_interval() may return incorrect information.
Assuming a failed update of the device means its actual state hasn't
changed, update the frame interval field of the device private
structure with a new value only after it is successfully applied on
hardware so it always reflects actual hardware state to the extent
possible. Also, initialise the field with hardware default frame
interval on device probe.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1463b371af ]
The driver stores crop rectangle settings supposed to be in line with
hardware state in a device private structure. Since the driver initial
submission, crop rectangle width and height settings are not updated
correctly when rectangle offset settings are applied on hardware. If
an error occurs while the device is updated, the stored settings my no
longer reflect hardware state and consecutive calls to .get_selection()
as well as .get/set_fmt() may return incorrect information. That in
turn may affect ability of a bridge device to use correct DMA transfer
settings if such incorrect informamtion on active frame format returned
by .get/set_fmt() is used.
Assuming a failed update of the device means its actual settings haven't
changed, update crop rectangle width and height settings stored in the
device private structure correctly while the rectangle offset is
successfully applied on hardware so the stored values always reflect
actual hardware state to the extent possible.
Fixes: 2f6e240479 ("[media] SoC Camera: add driver for OV6650 sensor")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3143b459de ]
The driver stores frame format settings supposed to be in line with
hardware state in a device private structure. Since the driver initial
submission, those settings are updated before they are actually applied
on hardware. If an error occurs on device update, the stored settings
my not reflect hardware state anymore and consecutive calls to
.get_fmt() may return incorrect information. That in turn may affect
ability of a bridge device to use correct DMA transfer settings if such
incorrect informmation on active frame format returned by .get_fmt() is
used.
Assuming a failed device update means its state hasn't changed, update
frame format related settings stored in the device private structure
only after they are successfully applied so the stored values always
reflect hardware state as closely as possible.
Fixes: 2f6e240479 ("[media] SoC Camera: add driver for OV6650 sensor")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d669fbfca ]
The initial registers sequence is only loaded at probe
time. Afterward only the resolution and format specific
register are modified. Care must be taken to make sure
registers modified by one resolution setting are reverted
back when another resolution is programmed.
This was not done properly for the 720p case.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b188d6ba2 ]
Commit 4f996594ce ("[media] v4l2: make vidioc_s_crop const")
introduced a writable copy of constified user requested crop rectangle
in order to be able to perform hardware alignments on it. Later
on, commit 10d5509c8d ("[media] v4l2: remove g/s_crop from video
ops") replaced s_crop() video operation using that const argument with
set_selection() pad operation which had a corresponding argument not
constified, however the original behavior of the driver was not
restored. Since that time, any hardware alignment applied on a user
requested crop rectangle is not passed back to the user calling
.set_selection() as it should be.
Fix the issue by dropping the copy and replacing all references to it
with references to the crop rectangle embedded in the user argument.
Fixes: 10d5509c8d ("[media] v4l2: remove g/s_crop from video ops")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85c4043f1d ]
In ov2659_s_stream() return value for invoked function should be checked
and propagated.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c404af950d ]
Since commit afd9690c72 ("[media] ov6650: convert to the control
framework"), if an error occurs during initialization of a control
handler, resources possibly allocated to the handler are not freed
before device initialiaton is aborted. Fix it.
Fixes: afd9690c72 ("[media] ov6650: convert to the control framework")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pull i2c updates from Wolfram Sang:
- new driver for ICY, an Amiga Zorro card :)
- axxia driver gained slave mode support, NXP driver gained ACPI
- the slave EEPROM backend gained 16 bit address support
- and lots of regular driver updates and reworks
* 'i2c/for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (52 commits)
i2c: tegra: Move suspend handling to NOIRQ phase
i2c: imx: ACPI support for NXP i2c controller
i2c: uniphier(-f): remove all dev_dbg()
i2c: uniphier(-f): use devm_platform_ioremap_resource()
i2c: slave-eeprom: Add comment about address handling
i2c: exynos5: Remove IRQF_ONESHOT
i2c: stm32f7: Make structure stm32f7_i2c_algo constant
i2c: cht-wc: drop check because i2c_unregister_device() is NULL safe
i2c-eeprom_slave: Add support for more eeprom models
i2c: fsi: Add of_put_node() before break
i2c: synquacer: Make synquacer_i2c_ops constant
i2c: hix5hd2: Remove IRQF_ONESHOT
i2c: i801: Use iTCO version 6 in Cannon Lake PCH and beyond
watchdog: iTCO: Add support for Cannon Lake PCH iTCO
i2c: iproc: Make bcm_iproc_i2c_quirks constant
i2c: iproc: Add full name of devicetree node to adapter name
i2c: piix4: Add ACPI support
i2c: piix4: Fix probing of reserved ports on AMD Family 16h Model 30h
i2c: ocores: use request_any_context_irq() to register IRQ handler
i2c: designware: Fix optional reset error handling
...
As pointed by cppcheck:
[drivers/media/i2c/ov9650.c:706]: (error) Shifting by a negative value is undefined behaviour
[drivers/media/i2c/ov9650.c:707]: (error) Shifting by a negative value is undefined behaviour
[drivers/media/i2c/ov9650.c:721]: (error) Shifting by a negative value is undefined behaviour
Prevent mangling with gains with invalid values.
As pointed by Sylvester, this should never happen in practice,
as min value of V4L2_CID_GAIN control is 16 (gain is always >= 16
and m is always >= 0), but it is too hard for a static analyzer
to get this, as the logic with validates control min/max is
elsewhere inside V4L2 core.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
No need to check the argument of i2c_unregister_device() because the
function itself does it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
No need to check the argument of i2c_unregister_device() because the
function itself does it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some users have been having a hard time finding the hidden
menus. A typically case are camera sensor drivers
(e.g IMX219, OV5645, etc), which are common on embedded
platforms and not really "ancillary" devices.
The problem with MEDIA_SUBDRV_AUTOSELECT seems to be related
to the fact that it uses the "visible" syntax to hide
the menus.
This is not obvious and it normally takes some time to
figure out.
To fix the problem, add a comment on each of hidden menus,
which should clarify what option is causing menus to be hidden.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This is mostly a port of Jacopo's fix:
commit aa4bb8b883
Author: Jacopo Mondi <jacopo@jmondi.org>
Date: Fri Jul 6 05:51:52 2018 -0400
media: ov5640: Re-work MIPI startup sequence
In the OV5645 case, the changes are:
- At set_power(1) time power up MIPI Tx/Rx and set data and clock lanes in
LP11 during 'sleep' and 'idle' with MIPI clock in non-continuous mode.
- At set_power(0) time power down MIPI Tx/Rx (in addition to the current
power down of regulators and clock gating).
- At s_stream time enable/disable the MIPI interface output.
With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.
Many thanks to Fabio Estevam for his help debugging this issue.
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Parse async sub-devices related to the sensor by switching the async
sub-device registration function.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of blindly trusting getting the clock frequency succeeded end then
testing it against a pre-defined value, verify reading the value
succeeded.
Fixes: 879347f0c2 ("media: ov8856: Add support for OV8856 sensor")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a V4L2 sub-device driver for Omnivision ov5675 image sensor.
This is a camera sensor using the I2C bus for control and the
CSI-2 bus for data.
This driver supports following features:
- manual exposure and analog/digital gain control support
- vblank/hblank control support
- test pattern support
- media controller support
- runtime PM support
- support following resolutions:
+ 2592x1944 at 30FPS
+ 1296x972 at 30FPS
[Sakari Ailus: Wrapped a few long lines.]
[mchehab+samsung@kernel.org: fix a checkpatch warning]
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the general move to have i2c_new_*_device functions which return
ERR_PTR instead of NULL, this patch converts i2c_new_secondary_device().
There are only few users, so this patch converts the I2C core and all
users in one go. The function gets renamed to i2c_new_ancillary_device()
so out-of-tree users will get a build failure to understand they need to
adapt their error checking code.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> # adv748x
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # adv7511 + adv7604
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # adv7604
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Convert this driver to use the new i2c_new_dummy_device() call and bail
out if the dummy device cannot be registered to make failure more
visible to the user.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The I2C core framework provides a simplified probe framework from commit
b8a1a4cd5a ("i2c: Provide a temporary .probe_new() call-back type").
These drivers do not utilise the i2c_device_id table in the probe, so we
can easily convert them to utilise the simplified i2c driver
registration.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The I2C core framework provides a simplified probe framework from commit
b8a1a4cd5a ("i2c: Provide a temporary .probe_new() call-back type").
This driver does not utilise the i2c_device_id table in the probe, so we can
easily convert it to utilise the simplified i2c driver registration.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The I2C core framework provides a simplified probe framework from commit
b8a1a4cd5a ("i2c: Provide a temporary .probe_new() call-back type").
This driver does not utilise the i2c_device_id table in the probe, so we can
easily convert it to utilise the simplified i2c driver registration.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The I2C core framework provides a simplified probe framework from commit
b8a1a4cd5a ("i2c: Provide a temporary .probe_new() call-back type").
This driver does not utilise the i2c_device_id table in the probe, so we can
easily convert it to utilise the simplified i2c driver registration.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The I2C core framework provides a simplified probe framework from commit
b8a1a4cd5a ("i2c: Provide a temporary .probe_new() call-back type").
Convert the ADV748x to utilise this simplified i2c driver registration.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a goto from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
goto in four places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Dan Carpenter