MTD_OOB_PLACE is supposed to read/write the raw oob data similiar to the
MTD_OOB_RAW however due to a bug, currently it is not possible to read
more data that is specified by the oob 'free' regions.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since all userspace threads are frozen at the time the nand_suspend is called,
they aren't inside any nand function.
We don't call try_to_freeze in nand ether. Thus the only user that can
be inside the nand functions is an non freezeable kernel thread. Thus we
can safely wait for it to finish.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Adds NAND Flash Controller driver for MPC5121 Revision 2.
All device features, except hardware ECC and power management,
are supported.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In the branch where pagesize equalled NAND_DATA_ACCESS_SIZE, NumToRead
wasn't decremented in the `while (numToRead > 11)' loop.
Also the first and last while loops were duplicated in both branches.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Leo Chen <leochen@broadcom.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is a bug in nand prefetch read routine, which comes into effect
only if nand device is a 16-bit device (as we have in zoom boards).
This bug is effective only with below combination of conditions:
1. nand deivce, in use, is a 16 bit device
2. nand driver supports 'subpage' read
3. SW ECC is in use
This was not seen old kernel (ex: .23), because when, in early days,
we tested this (nand prefetch read in LDP boards) there was no
'subpage read' support.
Later when we had subpage read in (.27) kernel, we had hw ecc enabled
always in our internal tree. So, we missed this bug.
This patch fixes the issue.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Removing OMAP NAND driver, when loaded as a module, gives error and
does not get success. This fixes this and makes driver loadable and
removable run time.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fixing below warning in compilation:
drivers/mtd/nand/omap2.c: In function 'omap_write_buf_dma_pref':
drivers/mtd/nand/omap2.c:508: warning: passing argument 2 of
'omap_nand_dma_transfer' discards qualifiers from pointer target type
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
mxc_nand driver must support the RESET Command in order to support
Micron NAND which need a reset before any other command.
Signed-off-by: Eric Benard <eric@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add nand lock / unlock routines. At least 'micron' parts
support this.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
... verification for 'nand_erase_nand'
These checks are expected to be used by 'nand_lock' and 'nand_unlock'
routines too. As all these three are block aligned operations.
So, creating a helper function for this makes sense.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
MAX_MTD_DEVICES is about to be removed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The clock must already be off after mtd->suspend. Disabling it again
results in an negative overflow of the clock usage count. This didn't
hurt as mxcnd_resume undid it after wake up.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The probe function calls platform_set_drvdata with a valid pointer when
the probe is successful. As mxcnd_suspend and mxcnd_resume are only
called on bound devices, platform_get_drvdata always returns non-NULL.
This fix isn't critical as the pointer is always valid so it doesn't
matter if the compiler generated code for it or not.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The match_table field of the struct of_device_id is constant in <linux/of_platform.h>
so it is worth to make xps2_of_match also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make alauda_table also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The id_table field of the struct pci_driver is constant in <linux/pci.h>
so it is worth to make cafe_nand_tbl also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Introducing 'gpmc-nand.c' for GPMC specific NAND init.
For example: GPMC timing parameters and all.
This patch also migrates gpmc related calls from 'nand/omap2.c'
to 'gpmc-nand.c'.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit e99030609e ("mtd: orion_nand.c: add
error handling and use resource_size()") introduced a build error -- it
assigns something to a undeclared variable 'err', whereas the rest of
the code uses 'ret' for this task.
This patch fixes this typo and thus removes the build failure.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch extends the sh_flctl driver with support
for 16-bit bus configuration using SEL_16BIT and
support for multiplexed pins using SHBUSSEL.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains a few changes for the sh_flctl driver:
- not sh7723-only driver - get rid of kconfig dependency
- use dev_err() instead of printk()
- use __devinit and __devexit for probe()/remove()
- fix probe() return values
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The ts72xx platform has been updated to use the generic platform nand
driver (plat_nand.c). This removes the now-defunct ts7250.c nand driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Matthieu Crapet <mcrapet@gmail.com>
Cc: Jesse Off <joff@embeddedARM.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Due to I have renamed the platform_device.name,so this patch changes
this nand driver platform_driver name.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove unnecessary casts and use dev_get_platdata() to retrieve the
struct mfd_cell data from the platform.
Use resource_size() for the ioremap()'s.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use platform_get_resource() to fetch the memory resource and
add error handling for when it is missing. Use resource_size()
for the ioremap().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The ioremap'ed sizes are off by 1; use resource_size() for correct value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove unnecessary casts for p_nand, it is already a void __iomem *.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use kzalloc() instead of kmalloc()/memset().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The platform has never been fully merged
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
* git://git.infradead.org/mtd-2.6: (90 commits)
jffs2: Fix long-standing bug with symlink garbage collection.
mtd: OneNAND: Fix test of unsigned in onenand_otp_walk()
mtd: cfi_cmdset_0002, fix lock imbalance
Revert "mtd: move mxcnd_remove to .exit.text"
mtd: m25p80: add support for Macronix MX25L4005A
kmsg_dump: fix build for CONFIG_PRINTK=n
mtd: nandsim: add support for 4KiB pages
mtd: mtdoops: refactor as a kmsg_dumper
mtd: mtdoops: make record size configurable
mtd: mtdoops: limit the maximum mtd partition size
mtd: mtdoops: keep track of used/unused pages in an array
mtd: mtdoops: several minor cleanups
core: Add kernel message dumper to call on oopses and panics
mtd: add ARM pismo support
mtd: pxa3xx_nand: Fix PIO data transfer
mtd: nand: fix multi-chip suspend problem
mtd: add support for switching old SST chips into QRY mode
mtd: fix M29W800D dev_id and uaddr
mtd: don't use PF_MEMALLOC
mtd: Add bad block table overrides to Davinci NAND driver
...
Fixed up conflicts (mostly trivial) in
drivers/mtd/devices/m25p80.c
drivers/mtd/maps/pcmciamtd.c
drivers/mtd/nand/pxa3xx_nand.c
kernel/printk.c
This reverts commit 82613b0da6, because
commit daa0f15 (mtd: don't use __exit_p to wrap mxcnd_remove) is a
better solution. Not having a remove callback breaks rebinding because
resources are not freed on remove.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
I was going to play with a faulty nand image from real flash and noticed
that nandsim does not work with:
first_id_byte=0xec second_id_byte=0xd5 third_id_byte=0x51 fourth_id_byte=0xa6
This patch seems to fix it.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since the same nand controller is shared between ARCH_PXA and ARCH_MMP. Move
the pxa3xx_nand.h from mach directory to plat directoy.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
MTD_NAND_PXA3xx module is shared between ARCH_PXA and ARCH_MMP. Update
this configuration according to it.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Support samsung 2GbX8 and 32GbX8 nand flash.
Support micron 4GbX8 and 4GbX16 nand flash.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
In some bootloader, IRQ is enabled. Writing nand triggers unexpected
interrupts. So disable nand irq in initialization. After nand
initialized and in working state, irq is controlled by nand driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Nand driver uses IRQ_NAND as hardcode irq number. In ARCH_MMP, the irq
number is different. So get irq resource from platform device structure
and use it in initialization and deinitialization code.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Although nand controller is same between PXA3xx and MMP, the register space
is different. Remove the hardcode register address setting in pxa3xx_nand.h.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Slow down the tRp of Micron NAND flash timing.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Initialize the read buffer content to 0xFF.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
When fetch nand data with non-DMA mode, we should align info->data_size to
32bit, not 8bit.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The shift operator used here to convert from bytes to 32-bit words is
backwards.
Signed-off-by: David Hunter <hunterd42@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Symptom:
device_suspend(): mtd_cls_suspend+0x0/0x58 returns -11
PM: Device mtd14 failed to suspend: error -11
PM: Some devices failed to suspend
This patch enables other chips to be suspended if the active chip of
the controller has been suspended.
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The existing NAND infrastructure allows the default main and
mirror bad block tables to be overridden in nand_default_bbt().
However, the davinci_nand driver does not support this. Add
that support by adding fields to the davinci driver's platform
data so platform code can pass in their own bbt's and make the
davinci_nand driver honor them.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
CC: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The function mxcnd_remove is defined using __devexit, so don't use
__exit_p but __devexit_p to wrap it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The function excite_nand_remove is used only wrapped by __devexit_p so
define it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We want error information even if the kernel hasn't been built for verbose
debugging.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently, the program and erase sequences do not wait for completion,
instead relying on a subsequent waitfunc() callback. However, this causes
the chipselect to be deasserted while the NAND chip is still asserting the
busy pin, which can corrupt activity on other chipselects.
This patch switches to using the sequences recommended by the manual,
in which a wait is performed within the initial command sequence. We can
now re-use the status byte from the initial command sequence, rather than
having to do another status read in the waitfunc.
Since we're already touching the command sequences, it also cleans up some
cruft in SEQIN that isn't needed since we cannot program partial pages
outside of OOB.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reported-by: Suchit Lepcha <suchit.lepcha@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When a NAND operation is in progress, all other localbus operations
(including NOR flash) will have to wait for access to the bus. However, the
NAND operation may take longer to complete than the default timeout. Thus,
if NOR is accessed while a NAND operation is in progress, the NAND operation
will fail.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Return a negative error value instead of a positive
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The index is signed, make sure it is not negative
when we read the array element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Update the nand information passed to the core from the platform data to
setup the initial option value, so that flags such as NAND_SCAN_SILENT_NODEV
can pass through.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add NAND_SCAN_SILENT_NODEV to chip->options to the user-worrying messages
'No NAND device found!!!'. This message often worries users (was three
exclamation marks really necessary?) and especially in systems such as the
Simtec Osiris where there may be optional NAND devices which are not
known until probe time.
Revised version of the original NAND_PROBE_SPECULATIVE patch after comments
by Artem Bityutskiy about adding a whole new call.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is a quick and dirty patch to add panic_write for NAND flashes. The
patch seems to work OK on my CRIS board running a 2.6.26 kernel with a
ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit), and also on a
OpenRD base (Marvell Kirkwood) board with a Toshiba NAND 512MiB 3,3V
8-bit flash with 2.6.32-pre1.
Signed-off-by: Edgar E. Iglesias <edgar@axis.com>
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add __nand_calculate_ecc() which does not take struct mtd_info.
The built-in 256/512 software ECC calculation and correction tester
will use it.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Later versions of this controller also allow 4k pagesize,
so use mtd->writesize instead of a flag.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The main/spare areas are on different addresses on later versions
of the controller, so make them configurable.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The NAND controller has some limitations how to access the
internal buffers. It only allows 32 bit accesses. The driver
used to work around this by having special alignment aware
copy routines.
We now copy the whole page to a buffer in memory and let the
access functions use this buffer. This simplifies the driver.
A bonnie++ test showed that this has no negative performance
impact on the driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This factors the address cycle to a seperate function. This
becomes useful in a later patch where we can simplify the
command processing by making use of this function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The oob layout was initialized several times. Instead, use
a smallpage layout by default and switch to a largepage
afterwards if necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The original Freescale driver used to have eccoob descriptions like
this:
static struct nand_ecclayout nand_hw_eccoob_8 = {
.eccbytes = 5,
.eccpos = {6, 7, 8, 9, 10},
.oobfree = {{0, 5}, {11, 5}}
};
static struct nand_ecclayout nand_hw_eccoob_16 = {
.eccbytes = 5,
.eccpos = {6, 7, 8, 9, 10},
.oobfree = {{0, 6}, {12, 4}}
};
The former was used for 8bit flashes and the latter for 16bit flashes.
They honored the fact that the bad block marker on 8bit flashes is on byte 5
while on 16bit flashes it is on byte 11.
In the Kernel driver this was copied wrong and we ended up with two identical
descriptions.
Change it so that we have only one description which leaves byte 5 and byte
11 unspecified so that it won't be used by others.
Also, rename the descriptions to nand_hw_eccoob_smallpage and
nand_hw_eccoob_largepage so that it can't be confused with Nand chip bus
widths (what actually happened in this driver)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
This reverts commit 71b7d0d90d.
The problem which that commit attempted to fix was a bootloader issue,
which had been misunderstood. The 'fix' causes lots of false bad blocks
for existing users with sane firmware.
Thanks to Mathieu Berland for diagnosing the problem coherently.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a request_mem_region() before doing the ioremap(). Also, use the
resource_size macro instead of doing the end - start + 1 calc by hand.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The function mxcnd_remove is used only wrapped by __exit_p so define it
using __exit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Vladimir Barinov <vova.barinov@gmail.com>
Cc: Vladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Correct typo to use mask_ale from platform data when set to non-zero.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fixed following htmldocs warnings:
DOCPROC Documentation/DocBook/mtdnand.xml
Warning(drivers/mtd/nand/nand_base.c:769): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:785): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:824): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:947): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:996): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:1040): No description found for parameter 'page'
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (58 commits)
mtd: jedec_probe: add PSD4256G6V id
mtd: OneNand support for Nomadik 8815 SoC (on NHK8815 board)
mtd: nand: driver for Nomadik 8815 SoC (on NHK8815 board)
m25p80: Add Spansion S25FL129P serial flashes
jffs2: Use SLAB_HWCACHE_ALIGN for jffs2_raw_{dirent,inode} slabs
mtd: sh_flctl: register sh_flctl using platform_driver_probe()
mtd: nand: txx9ndfmc: transfer 512 byte at a time if possible
mtd: nand: fix tmio_nand ecc correction
mtd: nand: add __nand_correct_data helper function
mtd: cfi_cmdset_0002: add 0xFF intolerance for M29W128G
mtd: inftl: fix fold chain block number
mtd: jedec: fix compilation problem with I28F640C3B definition
mtd: nand: fix ECC Correction bug for SMC ordering for NDFC driver
mtd: ofpart: Check availability of reg property instead of name property
driver/Makefile: Initialize "mtd" and "spi" before "net"
mtd: omap: adding DMA mode support in nand prefetch/post-write
mtd: omap: add support for nand prefetch-read and post-write
mtd: add nand support for w90p910 (v2)
mtd: maps: add mtd-ram support to physmap_of
mtd: pxa3xx_nand: add single-bit error corrections reporting
...
Maxim Levitsky
Anatolij Gustschin
Roel Kluin
Vimal Singh
Vimal Singh
Eric Benard
Ben Hutchings
Uwe Kleine-König
Márton Németh
Andrey Yurovsky
Peter Huewe
Daniel Mack
Magnus Damm
Baruch Siach
H Hartley Sweeten
David Woodhouse
Wan ZongShun
Ralf Baechle
Linus Torvalds
Alexey Dobriyan
André Goddard Rosa
Sebastian Andrzej Siewior
Haojian Zhuang
David Hunter
Li Yang
Mark A. Greer
Scott Wood
Akinobu Mita
Ben Dooks
Atsushi Nemoto
Simon Kagstrom
Tony Lindgren
Sascha Hauer
Michael Roth
Leo (Hao) Chen
Claudio Scordino
Hemant Pedanekar
Jaswinder Singh Rajput