The struct mips_fpu_soft_struct and mips_fpu_hard_struct are
completely same now and the kernel fpu emulator assumes that. This
patch unifies them to mips_fpu_struct and get rid of mips_fpu_union.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Support for the GT-64120-based Wind River 4KC PPMC Evaluation board.
Signed-off-by: Rongkai.Zhan <Rongkai.zhan@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
I found that NPTL's pthread_cond_signal() does not work properly on
kernels compiled by gcc 4.1.x. I suppose inline asm for
__futex_atomic_op() was wrong. I suppose:
1. "=&r" constraint should be used for oldval.
2. Instead of "r" (uaddr), "=R" (*uaddr) for output and "R" (*uaddr)
for input should be used.
3. "memory" should be added to the clobber list.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch from Andrew Victor
These headers define the registers and bits for the SPI (Serial
Peripheral Interface), SSC (Synchronous Serial), TC (Timer/Counter) and
UDP (USB Device) peripherals integrated in the AT91RM9200 processor.
(They will probably also be usable for the AT91SAM9 series of SoC
processors)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
Added definition for the bits in the Chip ID register.
Corrected the capitalization of AT91_RTC_AMPM register name.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The byte order functions are visible to userspace. Unfortunately,
__arch_swab32() contains an assembly instruction which is invalid when
compiling for Thumb. This reverts to the C version when compiling for
Thumb.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
The netX processors have generic network bitstream engines (XMAC/XPEC).
This driver adds support for firmware loading and start, stop, reset
commands.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch adds support for the pointer FIFOs on netX.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch adds the base support for Hilscher's netX network
processors.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch maps the AT91RM9200's internal SRAM into the virtual memory
address space - just below the internal peripheral registers.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch adds the register definitions for Hilscher's netX network
processors.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Core support for the Samsung S3C2442, and the
serial port driver update to allow the serial
port blocks to be used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch fixes some dyntick locking issues on ARM as pointed
out by Russell King.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Using the low-level debug routines early in the
kernel debug cause the 1:1 mapping to get into
the TLB, which is not flushed until after the
CPU detection process (which needs the GPIO VA).
This patch moves the VA for the GPIO to the
same offset as the physical offset of the UART
to the GPIO.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vitaly Wool
This patch adds kernel headers for PNX4008 ARM platform.
It's basically the same as the previos one, but with the rmk's comments taken into account.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Dmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Updates to the lpd7a40x_platform files. Includes support for new
architecture, lpd7a400.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Updates to the lpd7a40x platform headers. Includes support for new
architecture, lpd7a400.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current stack treats NETIF_F_HW_CSUM and NETIF_F_NO_CSUM
identically so we test for them in quite a few places. For the sake
of brevity, I'm adding the macro NETIF_F_GEN_CSUM for these two. We
also test the disjunct of NETIF_F_IP_CSUM and the other two in various
places, for that purpose I've added NETIF_F_ALL_CSUM.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
A lot of people have asked for a way to disable tcp_cwnd_restart(),
and it seems reasonable to add a sysctl to do that.
Signed-off-by: David S. Miller <davem@davemloft.net>
The sysctl net.ipv4.ip_autoconfig is a legacy value that is not used.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's better to warn and fail rather than rarely triggering BUG on paths
that incorrectly call skb_trim/__skb_trim on a non-linear skb.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
I found a few more spots where pskb_trim_rcsum could be used but were not.
This patch changes them to use it.
Also, sk_filter can get paged skb data. Therefore we must use pskb_trim
instead of skb_trim.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The linearisation operation doesn't need to be super-optimised. So we can
replace __skb_linearize with __pskb_pull_tail which does the same thing but
is more general.
Also, most users of skb_linearize end up testing whether the skb is linear
or not so it helps to make skb_linearize do just that.
Some callers of skb_linearize also use it to copy cloned data, so it's
useful to have a new function skb_linearize_cow to copy the data if it's
either non-linear or cloned.
Last but not least, I've removed the gfp argument since nobody uses it
anymore. If it's ever needed we can easily add it back.
Misc bugs fixed by this patch:
* via-velocity error handling (also, no SG => no frags)
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various drivers use xmit_lock internally to synchronise with their
transmission routines. They do so without setting xmit_lock_owner.
This is fine as long as netpoll is not in use.
With netpoll it is possible for deadlocks to occur if xmit_lock_owner
isn't set. This is because if a printk occurs while xmit_lock is held
and xmit_lock_owner is not set can cause netpoll to attempt to take
xmit_lock recursively.
While it is possible to resolve this by getting netpoll to use
trylock, it is suboptimal because netpoll's sole objective is to
maximise the chance of getting the printk out on the wire. So
delaying or dropping the message is to be avoided as much as possible.
So the only alternative is to always set xmit_lock_owner. The
following patch does this by introducing the netif_tx_lock family of
functions that take care of setting/unsetting xmit_lock_owner.
I renamed xmit_lock to _xmit_lock to indicate that it should not be
used directly. I didn't provide irq versions of the netif_tx_lock
functions since xmit_lock is meant to be a BH-disabling lock.
This is pretty much a straight text substitution except for a small
bug fix in winbond. It currently uses
netif_stop_queue/spin_unlock_wait to stop transmission. This is
unsafe as an IRQ can potentially wake up the queue. So it is safer to
use netif_tx_disable.
The hamradio bits used spin_lock_irq but it is unnecessary as
xmit_lock must never be taken in an IRQ handler.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new xtables target, CONNSECMARK, which is used to specify rules
for copying security marks from packets to connections, and for
copyying security marks back from connections to packets. This is
similar to the CONNMARK target, but is more limited in scope in that
it only allows copying of security marks to and from packets, as this
is all it needs to do.
A typical scenario would be to apply a security mark to a 'new' packet
with SECMARK, then copy that to its conntrack via CONNMARK, and then
restore the security mark from the connection to established and
related packets on that connection.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a secmark field to IP and NF conntracks, so that security markings
on packets can be copied to their associated connections, and also
copied back to packets as required. This is similar to the network
mark field currently used with conntrack, although it is intended for
enforcement of security policy rather than network policy.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a SECMARK target to xtables, allowing the admin to apply security
marks to packets via both iptables and ip6tables.
The target currently handles SELinux security marking, but can be
extended for other purposes as needed.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a secmark field to the skbuff structure, to allow security subsystems to
place security markings on network packets. This is similar to the nfmark
field, except is intended for implementing security policy, rather than than
networking policy.
This patch was already acked in principle by Dave Miller.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and export new functions to the in-kernel SELinux API in support of the
new secmark-based packet controls.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assignment used as truth value in xfrm_del_sa()
and xfrm_get_policy().
Wrong argument type declared for security_xfrm_state_delete()
when SELINUX is disabled.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains a fix for the previous patch that adds security
contexts to IPsec policies and security associations. In the previous
patch, no authorization (besides the check for write permissions to
SAD and SPD) is required to delete IPsec policies and security
assocations with security contexts. Thus a user authorized to change
SAD and SPD can bypass the IPsec policy authorization by simply
deleteing policies with security contexts. To fix this security hole,
an additional authorization check is added for removing security
policies and security associations with security contexts.
Note that if no security context is supplied on add or present on
policy to be deleted, the SELinux module allows the change
unconditionally. The hook is called on deletion when no context is
present, which we may want to change. At present, I left it up to the
module.
LSM changes:
The patch adds two new LSM hooks: xfrm_policy_delete and
xfrm_state_delete. The new hooks are necessary to authorize deletion
of IPsec policies that have security contexts. The existing hooks
xfrm_policy_free and xfrm_state_free lack the context to do the
authorization, so I decided to split authorization of deletion and
memory management of security data, as is typical in the LSM
interface.
Use:
The new delete hooks are checked when xfrm_policy or xfrm_state are
deleted by either the xfrm_user interface (xfrm_get_policy,
xfrm_del_sa) or the pfkey interface (pfkey_spddelete, pfkey_delete).
SELinux changes:
The new policy_delete and state_delete functions are added.
Signed-off-by: Catherine Zhang <cxzhang@watson.ibm.com>
Signed-off-by: Trent Jaeger <tjaeger@cse.psu.edu>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users pass 32-bit values as addresses and internally they're
compared with 32-bit entities. So, change "laddr" and "raddr" types to
__be32.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users except two expect 32-bit big-endian value. One is of
->multiaddr = ->multiaddr
variety. And last one is "%08lX".
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many of the TCP congestion methods all just use ssthresh
as the minimum congestion window on decrease. Rather than
duplicating the code, just have that be the default if that
handle in the ops structure is not set.
Minor behaviour change to TCP compound. It probably wants
to use this (ssthresh) as lower bound, rather than ssthresh/2
because the latter causes undershoot on loss.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
