Make this depend on CONFIG_PM. This protection is necessary to not
cause any build errors with any combination of PM features especially
when supporting a new SoC where each PM features are being enabled
one-by-one during its depelopment.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With recent arm broadcast time clean-up from Mark Rutland, the dummy
broadcast device is always registered with timer subsystem. And since
the rating of the dummy clock event is very high, it may be preferred
over a real clock event.
This is a change in behavior from past and not an intended one. So
reduce the rating of the dummy clock-event so that real clock-event
device is selected when available.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes a kernel crash when using precise sampling (PEBS)
after a suspend/resume. Turns out the CPU notifier code is not invoked
on CPU0 (BP). Therefore, the DS_AREA (used by PEBS) is not restored properly
by the kernel and keeps it power-on/resume value of 0 causing any PEBS
measurement to crash when running on CPU0.
The workaround is to add a hook in the actual resume code to restore
the DS Area MSR value. It is invoked for all CPUS. So for all but CPU0,
the DS_AREA will be restored twice but this is harmless.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The i.MX35 has two bits per clock gate which are decoded as follows:
0b00 -> clock off
0b01 -> clock is on in run mode, off in wait/doze
0b10 -> clock is on in run/wait mode, off in doze
0b11 -> clock is always on
The reset value for the MAX clock is 0b10.
The MAX clock is needed by the SoC, yet unused in the Kernel, so the
common clock framework will disable it during late init time. It will
only disable clocks though which it detects as being turned on. This
detection is made depending on the lower bit of the gate. If the reset
value has been altered by the bootloader to 0b11 the clock framework
will detect the clock as turned on, yet unused, hence it will turn it
off and the system locks up.
This patch turns the MAX clock on unconditionally making the Kernel
independent of the bootloader.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
During the transition to the generic parser, the hook to the codec
specific automute function was forgotten. This resulted in the silent
output on some MacBooks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When neighbour table is full, dst_neigh_lookup/dst_neigh_lookup_skb will return
-ENOBUFS which is absolutely non zero, while all the code in kernel which use
above functions assume failure only on zero return which will cause panic. (for
example: : https://bugzilla.kernel.org/show_bug.cgi?id=54731).
This patch corrects above error with smallest changes to kernel source code and
also correct two return value check missing bugs in drivers/infiniband/hw/cxgb4/cm.c
Tested on my x86_64 SMP machine
Reported-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Tested-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Signed-off-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kconfig file help information incorrectly mentions that the
SMSC LAN75xx config option is for SMSC LAN95xx devices.
Signed-off-by: Robert de Vries <rhdv@xs4all.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross says:
====================
A few different bug fixes, including several for issues with userspace
communication that have gone unnoticed up until now. These are intended
for net/3.9.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dc975382d2 introduces napi support
but never calls napi_disable. This will generate a kernel oops
(kernel BUG at include/linux/netdevice.h:473!) every time, when
ndo_stop is called followed by ndo_start.
Add the missing napi_diable call.
Signed-off-by: Georg Hofmann <georg@hofmannsweb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Proviously we would only restart the FEC when PHY link or duplex state
changed. PHY does not always bring down the link for speed changes, in
which case we would not detect any change and keep FEC running.
Switching link speed without restarting the FEC results in the FEC being
stuck in an indefinite state, generating error conditions for every
packet.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scorpion processors have always been v7 CPUs. Fix the Kconfig
text to reflect this.
Reported-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Haojian Zhuang <haojian.zhuang@gmail.com>:
* 'armsoc/fix' of git://github.com/hzhuang1/linux:
ARM: mmp: add platform_device head file in gplugd
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
arch/arm/mach-mmp/gplugd.c: In function ‘gplugd_init’:
arch/arm/mach-mmp/gplugd.c:188:2: error: implicit declaration of
function ‘platform_device_register’
[-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[1]: *** [arch/arm/mach-mmp/gplugd.o] Error 1
make: *** [arch/arm/mach-mmp] Error 2
So append platform_device.h to resolve build issue.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
"chn" here is a number between 0 and 255, but ->chn_info[] only has
16 elements so there is a potential write beyond the end of the
array.
If the seq_mode isn't SEQ_2 then we let the individual drivers
(either opl3.c or midi_synth.c) handle it. Those functions all
do a bounds check on "chn" so I haven't changed anything here.
The opl3.c driver has up to 18 channels and not 16.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
4740f73fe5 "mfd: remove use of __devexit" removed the __devexit annotation
on the twl4030_madc_remove function, but left an __exit_p() present on the
pointer to this function. Using __exit_p was as wrong with the devexit in
place as it is now, but now we get a gcc warning about an unused function.
In order for the twl4030_madc_remove to work correctly in built-in code, we
have to remove the __exit_p.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
spec->dsp_state is initialized to DSP_DOWNLOAD_INIT, no need to reset
and check it in ca0132_download_dsp().
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of using the dspload_is_loaded() function, check the dsp_state
that is kept in the spec. The dspload_is_loaded() function returns
true if the DSP transfer was never started. This false-positive leads
to multiple second delays when ca0132_setup_efaults() times out on
each write.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If dspload_image() fails, it was ignored and dspload_wait_loaded() was
still called. dsp_loaded should never be set to true in this case,
skip it. The check in dspload_wait_loaded() return true if the DSP is
loaded or if it never started.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The latency tracers require the buffers to be in overwrite mode,
otherwise they get screwed up. Force the buffers to stay in overwrite
mode when latency tracers are enabled.
Added a flag_changed() method to the tracer structure to allow
the tracers to see what flags are being changed, and also be able
to prevent the change from happing.
Cc: stable@vger.kernel.org
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Changing the overwrite mode for the ring buffer via the trace
option only sets the normal buffer. But the snapshot buffer could
swap with it, and then the snapshot would be in non overwrite mode
and the normal buffer would be in overwrite mode, even though the
option flag states otherwise.
Keep the two buffers overwrite modes in sync.
Cc: stable@vger.kernel.org
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The vm_flags introduced in 6d7825b10d ("mm/fremap.c: fix oops on error
path") is supposed to avoid a compiler warning about unitialized
vm_flags without changing the generated code.
However I am concerned that this is going to be very brittle, and fail
with some compiler versions. The failure could be either of:
- compiler could actually load vma->vm_flags before checking for the
!vma condition, thus reintroducing the oops
- compiler could optimize out the !vma check, since the pointer just got
dereferenced shortly before (so the compiler knows it can't be NULL!)
I propose reversing this part of the change and initializing vm_flags to 0
just to avoid the bogus uninitialized use warning.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are part of a longer series that has been submitted some time
ago for the frame buffer tree, but it was never accepted there.
The first two of the five patches are bug fixes, so let's merge
this through arm-soc to get a working 3.9 kernel for at91.
* commit '67cf9c0a':
ARM: at91: fix LCD-wiring mode
atmel_lcdfb: fix 16-bpp modes on older SOCs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Two more for fixing PM suspend/resume IRQ on AIC5 and
GPIO used with pinctrl.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRQYyVAAoJEAf03oE53VmQsz0IAMfjyOwqbuKmSwjV6HZAsu/k
/p8MB6F5Fg4PuBsPim+F8/kIWYuxSH/H17nwdA9fgWt6E8Z0zFtfbqvQkaTxWI/K
HWLZh6Z4ZHalDBInl1bTJ+mzMH2EaIZmJDZF7uOsE5EJz9b+tMzSZbaWWLllFwvQ
mSMidkg0x9fSI7GAoO7x/uxDPV5TdU2pSw5rFUfAIURXlGX1OVE9/Mpy9Utmmlax
3af3C2FgnlSLaVTHUv7dnefaSkBTJNFb0kydn7sgNa0tIRj2/pfG+xeXV+pEB92Y
UhNKS850DyAyWgBBxckQuUnin2v3snMazfbRiKbBGFnGlbIomDdFhpNu7ynRvfc=
=9r9y
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
From Nicolas Ferre <nicolas.ferre@atmel.com>:
Two patches for Device Tree on at91sam9x5/NAND.
Two more for fixing PM suspend/resume IRQ on AIC5 and
GPIO used with pinctrl.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: fix infinite loop in at91_irq_suspend/resume
ARM: at91: add gpio suspend/resume support when using pinctrl
ARM: at91: dt: at91sam9x5: complete NAND pinctrl
ARM: at91: dt: at91sam9x5: correct NAND pins comments
Includes an update to -rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull fix for hlist_entry_safe() regression from Paul McKenney:
"This contains a single commit that fixes a regression in
hlist_entry_safe(). This macro references its argument twice, which
can cause NULL-pointer errors. This commit applies a gcc statement
expression, creating a temporary variable to avoid the double
reference. This has been posted to LKML at
https://lkml.org/lkml/2013/3/9/75.
Kudos to CAI Qian, whose testing uncovered this, to Eric Dumazet, who
spotted root cause, and to Li Zefan, who tested this commit."
* 'rcu/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
list: Fix double fetch of pointer in hlist_entry_safe()
ARM normally has an accurate clock source, so
we can theoretically use analog joysticks more
accurately and at the same time avoid the
build warning
#warning Precise timer not defined for this architecture.
from the joystick driver.
Now, why anybody would use that driver no ARM I have no
idea, but Ben Dooks enabled it in the s3c2410_defconfig
along with a bunch of other drivers, even though that
platform has neither ISA nor PCI support. It still
seems to be the right thing to fix this quirk.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Ben Dooks <ben-linux@fluff.org>
56bc911 "[media] s5p-fimc: Redefine platform data structure for fimc-is"
changed the bus_type member of struct fimc_source_info treewide, but
got one instance wrong in mach-s5pv210, which was evidently not
even build tested.
This adds the missing change to get s5pv210_defconfig to build again.
Applies on the Mauro's media tree.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch 72480014b8 "Fix device clock divisor calculations" was apparently
rebased incorrectly before it got upstream, causing a build error.
Replacing the "prate" pointer with the local parent_rate is most
likely the correct solution.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Mike Turquette <mturquette@linaro.org>
The current version of hlist_entry_safe() fetches the pointer twice,
once to test for NULL and the other to compute the offset back to the
enclosing structure. This is OK for normal lock-based use because in
that case, the pointer cannot change. However, when the pointer is
protected by RCU (as in "rcu_dereference(p)"), then the pointer can
change at any time. This use case can result in the following sequence
of events:
1. CPU 0 invokes hlist_entry_safe(), fetches the RCU-protected
pointer as sees that it is non-NULL.
2. CPU 1 invokes hlist_del_rcu(), deleting the entry that CPU 0
just fetched a pointer to. Because this is the last entry
in the list, the pointer fetched by CPU 0 is now NULL.
3. CPU 0 refetches the pointer, obtains NULL, and then gets a
NULL-pointer crash.
This commit therefore applies gcc's "({ })" statement expression to
create a temporary variable so that the specified pointer is fetched
only once, avoiding the above sequence of events. Please note that
it is the caller's responsibility to use rcu_dereference() as needed.
This allows RCU-protected uses to work correctly without imposing
any additional overhead on the non-RCU case.
Many thanks to Eric Dumazet for spotting root cause!
Reported-by: CAI Qian <caiqian@redhat.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Li Zefan <lizefan@huawei.com>
Pull ext2, ext3, reiserfs, quota fixes from Jan Kara:
"A fix for regression in ext2, and a format string issue in ext3. The
rest isn't too serious."
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext2: Fix BUG_ON in evict() on inode deletion
reiserfs: Use kstrdup instead of kmalloc/strcpy
ext3: Fix format string issues
quota: add missing use of dq_data_lock in __dquot_initialize
Creating snapshot passes extent_root to commit its transaction,
but it can lead to the warning of checking root for quota in
the __btrfs_end_transaction() when someone else is committing
the current transaction. Since we've recorded the needed root
in trans_handle, just use it to get rid of the warning.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
If one of qgroup fails to reserve firstly, we should return immediately,
it is unnecessary to continue check.
Signed-off-by: Wang Shilong <wangsl-fnst@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
The callers of lookup_inline_extent_info all handle getting an error back
properly, so return an error if we have corruption instead of being a jerk and
panicing. Still WARN_ON() since this is kind of crucial and I've been seeing it
a bit too much recently for my taste, I think we're doing something wrong
somewhere. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Doing this would reliably fail with -EBUSY for me:
# mount /dev/sdb2 /mnt/scratch; umount /mnt/scratch; mkfs.btrfs -f /dev/sdb2
...
unable to open /dev/sdb2: Device or resource busy
because mkfs.btrfs tries to open the device O_EXCL, and somebody still has it.
Using systemtap to track bdev gets & puts shows a kworker thread doing a
blkdev put after mkfs attempts a get; this is left over from the unmount
path:
btrfs_close_devices
__btrfs_close_devices
call_rcu(&device->rcu, free_device);
free_device
INIT_WORK(&device->rcu_work, __free_device);
schedule_work(&device->rcu_work);
so unmount might complete before __free_device fires & does its blkdev_put.
Adding an rcu_barrier() to btrfs_close_devices() causes unmount to wait
until all blkdev_put()s are done, and the device is truly free once
unmount completes.
Cc: stable@vger.kernel.org
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Remove a useless function declaration
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Using spinning case instead of blocking will result in better concurrency
overall.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Seems that the tracer flags have never been protected from
synchronous writes. Luckily, admins don't usually modify the
tracing flags via two different tasks. But if scripts were to
be used to modify them, then they could get corrupted.
Move the trace_types_lock that protects against tracers changing
to also protect the flags being set.
Cc: stable@vger.kernel.org
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
On LTC2978, only READ_TEMPERATURE is supported. It reports
the internal junction temperature. This register is unpaged.
On LTC3880, READ_TEMPERATURE and READ_TEMPERATURE2 are supported.
READ_TEMPERATURE is paged and reports external temperatures.
READ_TEMPERATURE2 is unpaged and reports the internal junction
temperature.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.2+
Acked-by: Jean Delvare <khali@linux-fr.org>
Hi.
I'm trying to send big chunks of memory from application address space via
TCP socket using vmsplice + splice like this
mem = mmap(128Mb);
vmsplice(pipe[1], mem); /* splice memory into pipe */
splice(pipe[0], tcp_socket); /* send it into network */
When I'm lucky and a huge page splices into the pipe and then into the socket
_and_ client and server ends of the TCP connection are on the same host,
communicating via lo, the whole connection gets stuck! The sending queue
becomes full and app stops writing/splicing more into it, but the receiving
queue remains empty, and that's why.
The __skb_fill_page_desc observes a tail page of a huge page and erroneously
propagates its page->pfmemalloc value onto socket (the pfmemalloc on tail pages
contain garbage). Then this skb->pfmemalloc leaks through lo and due to the
tcp_v4_rcv
sk_filter
if (skb->pfmemalloc && !sock_flag(sk, SOCK_MEMALLOC)) /* true */
return -ENOMEM
goto release_and_discard;
no packets reach the socket. Even TCP re-transmits are dropped by this, as skb
cloning clones the pfmemalloc flag as well.
That said, here's the proper page->pfmemalloc propagation onto socket: we
must check the huge-page's head page only, other pages' pfmemalloc and mapping
values do not contain what is expected in this place. However, I'm not sure
whether this fix is _complete_, since pfmemalloc propagation via lo also
oesn't look great.
Both, bit propagation from page to skb and this check in sk_filter, were
introduced by c48a11c7 (netvm: propagate page->pfmemalloc to skb), in v3.5 so
Mel and stable@ are in Cc.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chrome OS team reported a crash on a Pixel ChromeBook in TCP stack :
https://code.google.com/p/chromium/issues/detail?id=182056
commit a21d45726a (tcp: avoid order-1 allocations on wifi and tx
path) did a poor choice adding an 'avail_size' field to skb, while
what we really needed was a 'reserved_tailroom' one.
It would have avoided commit 22b4a4f22d (tcp: fix retransmit of
partially acked frames) and this commit.
Crash occurs because skb_split() is not aware of the 'avail_size'
management (and should not be aware)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Mukesh Agrawal <quiche@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are no internal speakers, we should not turn the eapd switch
off, because it might be necessary to keep high for Headphone.
BugLink: https://bugs.launchpad.net/bugs/1155016
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If krealloc() returns NULL, it *doesn't* free the original. So any code
of the form 'foo = krealloc(foo, …);' is almost certainly a bug.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This partially reverts commit 1696e6bc2a
("mtd: nand: kill NAND_NO_READRDY").
In that patch I overlooked a few things.
The original documentation for NAND_NO_READRDY included "True for all
large page devices, as they do not support autoincrement." I was
conflating "not support autoincrement" with the NAND_NO_AUTOINCR option,
which was in fact doing nothing. So, when I dropped NAND_NO_AUTOINCR, I
concluded that I then could harmlessly drop NAND_NO_READRDY. But of
course the fact the NAND_NO_AUTOINCR was doing nothing didn't mean
NAND_NO_READRDY was doing nothing...
So, NAND_NO_READRDY is re-introduced as NAND_NEED_READRDY and applied
only to those few remaining small-page NAND which needed it in the first
place.
Cc: stable@kernel.org [3.5+]
Reported-by: Alexander Shiyan <shc_work@mail.ru>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The i.MX25 DT machine descriptor calls a non existing imx25_timer_init()
function. This patch adds it to fix compilation.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The tokens MADV_HUGEPAGE and MADV_NOHUGEPAGE are not available with
glibc 2.12 and older. Define these tokens if they are not already
defined.
This patch fixes these build errors with older versions of glibc.
CC bench/numa.o
bench/numa.c: In function ‘alloc_data’:
bench/numa.c:334: error: ‘MADV_HUGEPAGE’ undeclared (first use in this function)
bench/numa.c:334: error: (Each undeclared identifier is reported only once
bench/numa.c:334: error: for each function it appears in.)
bench/numa.c:341: error: ‘MADV_NOHUGEPAGE’ undeclared (first use in this function)
make: *** [bench/numa.o] Error 1
Signed-off-by: Vinson Lee <vlee@twitter.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Irina Tirdea <irina.tirdea@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1363214064-4671-2-git-send-email-vlee@twitter.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
fix typo error introduced by commit ea0e6276 (usb: gadget: add
multiple definition guards) which causes the following build warning:
warning: "pr_vdebug" redefined
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
