Allow the triggering of CSA frame using mesh interface. The
rules are more or less same with IBSS, such as not allowed to
change between the band and channel width has to be same from
the previous mode. Also, move the ieee80211_send_action_csa
to a common space so that it can be re-used by mesh interface.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixes errors in the mesh powersave logic which
cause that remote peers do not get peer power mode change
notifications and mesh peer service periods (MPSPs) got
stuck.
When closing a peer link, set the (now invalid) peer-specific
power mode to 'unknown'.
Avoid overhead when local power mode is unchanged.
Reliably clear MPSP flags on peering status update.
Avoid MPSP flags getting stuck by not requesting a further
MPSP ownership if we already are an MPSP owner.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver requests to move to STATIC or DYNAMIC SMPS,
we send an action frame to each associated station and
reconfigure the channel context / driver.
Of course, non-MIMO stations are ignored.
The beacon isn't updated. The association response will
include the original capabilities. Stations that associate
while in non-OFF SMPS mode will get an action frame right
after association to inform them about our current state.
Note that we wait until the end of the EAPOL. Sending an
action frame before the EAPOL is finished can be an issue
for a few clients. Clients aren't likely to send EAPOL
frames in MIMO anyway.
When the SMPS configuration gets more permissive (e.g.
STATIC -> OFF), we don't wake up stations that are asleep
We remember that they don't know about the change and send
the action frame when they wake up.
When the SMPS configuration gets more restrictive (e.g.
OFF -> STATIC), we set the TIM bit for every sleeping STA.
uAPSD stations might send MIMO until they poll the action
frame, but this is for a short period of time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[fix vht streams loop, initialisation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Limit the current implementation to a single channel context used by
a single vif, thereby avoiding multi-vif/channel complexities.
Reuse the main function from AP CSA code, but move a portion out in
order to fit the STA scenario.
Add a new mac80211 HW flag so we don't break devices that don't support
channel switch with channel-contexts. The new behavior will be opt-in.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows calls for clients in AP_VLANs (e.g. for 4-addr) to succeed
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function adds the channel switch announcement implementation for the
IBSS code. It is triggered by userspace (mac80211/cfg) or by external
channel switch announcement, which have to be adopted. Both CSAs in
beacons and action frames are supported. As for AP mode, the channel
switch is applied after some time. However in IBSS mode, the channel
switch IEs are generated in the kernel.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the wdev from cfg80211 on to the driver as the vif
if given and it's valid for the driver.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To allow drivers to implement per-interface testmode operations
more easily, pass a wdev pointer if any identification for one
was given from userspace. Clean up the code a bit while at it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The count field in CSA must be decremented with each beacon
transmitted. This patch implements the functionality for drivers
using ieee80211_beacon_get(). Other drivers must call back manually
after reaching count == 0.
This patch also contains the handling and finish worker for the channel
switch command, and mac80211/chanctx code to allow to change a channel
definition of an active channel context.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[small cleanups, catch identical chandef]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The various components accessing the bitrates table must use consider
the used channel bandwidth to select only available rates or calculate
the bitrate correctly.
There are some rates in reduced bandwidth modes which can't be
represented as multiples of 500kbps, like 2.25 MBit/s in 5 MHz mode. The
standard suggests to round up to the next multiple of 500kbps, just do
that in mac80211 as well.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[make rate unsigned in ieee80211_add_tx_radiotap_header(), squash fix]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
As reported in https://bugzilla.kernel.org/show_bug.cgi?id=60514,
the station loop never initialises 'sinfo' and therefore adds up
a stack values, leaking stack information (the number of times it
adds values is easily obtained another way.)
Fix this by initialising the sinfo for each station to add.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Useful for userspace mesh to authenticate and peer without
a station entry, since both steps may fail anyway.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge mac80211 to avoid conflicts with the nl80211 attrbuf
changes.
Conflicts:
net/mac80211/iface.c
net/wireless/nl80211.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 6d810f1032
In this way an IBSS station will not use the AUTH messages
to trigger a state reinitialisation anymore.
The behaviour was racy and was not working properly.
It has been introduced to help wpa_supplicant to support
IBSS/RSN, however all the logic is now getting moved into
wpa_s itself which will also be in charge of handling the
AUTH messages thanks to the mgmt frame registration.
If userspace does not register for receiving AUTH frames
then mac80211 will still reply by itself.
At the same time, the auth frame registration counter can be
removed since it is not needed anymore.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[remove unused variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a CAC is running and stop_ap is called (e.g. when hostapd is killed
while performing CAC), the CAC must be aborted immediately.
Otherwise ieee80211_stop_ap() will try to stop it when it's too late -
wdev->channel is already NULL and the abort event can not be generated.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211 passes a NULL channel to mgmt_tx if the frame has
to be sent on the one currently in use by the device.
Make the implementation of mgmt_tx correctly handle this
case. Fail if offchan is required.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[fix RCU locking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently mesh uses mandatory rates as the default basic rates. Allow basic
rates to be configured during mesh join. Basic rates are applied only if
channel is also provided with mesh join command.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
[some whitespace fixes, refuse basic rates w/o channel]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The time it takes to see the peer link expire may differ
by a minute since sta_expire() is run once a minute as a
mesh housekeeping task.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My cfg80211/mac80211 locking unification broke the sdata
locking in ieee80211_set_power_mgmt, it needs to acquire
the lock for __ieee80211_request_smps(). Add the locking.
Reported-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support them only if the driver advertises support for them via
IEEE80211_HW_SUPPORTS_ACTIVE_MONITOR. Unlike normal monitor interfaces,
they are added to the driver, along with their MAC address.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using separate locks in cfg80211 and mac80211 has always
caused issues, for example having to unlock in places in
mac80211 to call cfg80211, which even needed a framework
to make cfg80211 calls after some functions returned etc.
Additionally, I suspect some issues people have reported
with the cfg80211 state getting confused could be due to
such issues, when cfg80211 is asking mac80211 to change
state but mac80211 is in the process of telling cfg80211
that the state changed (in another way.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously the mesh_auth_id was disabled. Instead set the
correct mesh authentication bit based on the mesh setup.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no real difference between *array and array, but
the former confuses smatch so write it differently. The
generated code is exactly the same.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The RCU docs used to state that rcu_barrier() included a wait
for an RCU grace period; however the comments for rcu_barrier()
as of commit f0a0e6f... "rcu: Clarify memory-ordering properties
of grace-period primitives" contradict this.
So add back synchronize_{rcu,net}() to where they once were,
but keep the rcu_barrier()s for the call_rcu() callbacks.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bob Copeland <bob@cozybit.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the code always copies the configured MCS mask (even if it is
set to default), but only uses it if legacy rates were also masked out.
Fix this by adding a flag that tracks whether the configured MCS mask is
set to default or not.
Optimize the code further by storing a pointer to the configured rate
mask in txrc instead of using memcpy.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When AP interface is stopped ssid_len in the BSS configuration
isn't cleared which can confuse drivers when switching modes.
Set the length to zero when stopping the AP interface.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Most times that mesh_path_add() is called, it is followed by
a lookup to get the just-added mpath. We can instead just
return the new mpath in the case that we allocated one (or the
existing one if already there), so do that. Also, reorder the
code in mesh_path_add a bit so that we don't need to allocate
in the pre-existing case.
Signed-off-by: Bob Copeland <bob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a ROC item is canceled just as it expires, the work
struct may be scheduled while it is running (and waiting
for the mutex). This results in it being run after being
freed, which obviously crashes.
To fix this don't free it when aborting is requested but
instead mark it as "to be freed", which makes the work a
no-op and allows freeing it outside.
Cc: stable@vger.kernel.org [3.6+]
Reported-by: Jouni Malinen <j@w1.fi>
Tested-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add P2P NoA settings for STA mode.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[fix docs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a key is allocated but not really added, there's no
need to go through the entire teardown process. Also, if
adding a key fails, ieee80211_key_link() can take care of
freeing it instead of the (only) caller.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the TX bytes/packets counters race-free by keeping
them per AC so concurrent TX on queues can't cause lost
or wrong updates. This works since each station belongs
to a single interface. While at it also make the bytes
counters 64-bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Earlier mac80211 would check whether some kind of mesh
security was enabled, when the real question was "is the
MPM in userspace"?
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh station types used to refer to whether the
station was secure or nonsecure. Really the salient
information is whether it is managed by the kernel or
userspace
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since hostapd will remove keys this isn't usually
an issue, but we shouldn't leak keys to the next
BSS started on the same interface. For VLANs this
also fixes a bug, keys that aren't removed would
otherwise be leaked.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During roaming, the crypto_tx_tailroom_needed_cnt counter
will often take values 2,1,0,1,2 because first keys are
removed and then new keys are added. This is inefficient
because during the 0->1 transition, synchronize_net must
be called to avoid packet races, although typically no
packets would be flowing during that time.
To avoid that, defer the decrement (2->1, 1->0) when keys
are removed (by half a second). This means the counter
will really have the values 2,2,2,3,4 ... 2, thus never
reaching 0 and having to do the 0->1 transition.
Note that this patch entirely disregards the drivers for
which this optimisation was done to start with, for them
the key removal itself will be expensive because it has
to synchronize_net() after the counter is incremented to
remove the key from HW crypto. For them the sequence will
look like this: 0,1,0,1,0,1,0,1,0 (*) which is clearly a
lot more inefficient. This could be addressed separately,
during key removal the 0->1->0 sequence isn't necessary.
(*) it starts at 0 because HW crypto is on, then goes to
1 when HW crypto is disabled for a key, then back to
0 because the key is deleted; this happens for both
keys in the example. When new keys are added, it goes
to 1 first because they're added in software; when a
key is moved to hardware it goes back to 0
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices can handle remain on channel requests differently
based on the request type/priority. Add support to
differentiate between different ROC types, i.e., indicate that
the ROC is required for sending managment frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The station change API isn't being checked properly before
drivers are called, and as a result it is difficult to see
what should be allowed and what not.
In order to comprehensively check the API parameters parse
everything first, and then have the driver call a function
(cfg80211_check_station_change()) with the additionally
information about the kind of station that is being changed;
this allows the function to make better decisions than the
old code could.
While at it, also add a few checks, particularly in mesh
and clarify the TDLS station lifetime in documentation.
To be able to reduce a few checks, ignore any flag set bits
when the mask isn't set, they shouldn't be applied then.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the ability to leave the plink_state unchanged not use a
magic -1 variable that isn't in the enum, but an explicit change
flag; reject invalid plink states or actions and move the needed
constants for plink actions to the right header file. Also
reject plink_state changes for non-mesh interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After Felix's patch it was still broken in case you
used more than just a single monitor interface. Fix
it better now.
Reported-by: Sujith Manoharan <sujith@msujith.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When not using channel contexts with only monitor mode interfaces being
active, report local->monitor_chandef to userspace.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's various code with strange indentation,
questionable loop and locking constructs, etc.
The bigger change is moving the "sdata" argument
to the first argument of all functions, like all
other mac80211 functions that have one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The information of the peer's capabilities is required for the driver
to perform TDLS Peer UAPSD operations. This information of the peer is
passed by the supplicant using NL80211_CMD_SET_STATION command. This
commit enhances the function nl80211_set_station to pass this
information of the peer to the driver in case this command is used
with the TDLS peer STA.
In addition, make the HT/VHT capability configuration handled more
consistently for other STA cases (reject both instead of just HT).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, the entire mesh beacon would be generated each
time the beacon timer fired. Instead generate a beacon
head and tail (so the TIM can easily be inserted when mesh
power save is on) when starting a mesh or the MBSS
parameters change.
Also add a mutex for protecting beacon updates and
preventing leaks.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For VHT, many more bandwidth changes are possible. As a first
step, stop toggling the IEEE80211_HT_CAP_SUP_WIDTH_20_40 flag
in the HT capabilities and instead introduce a bandwidth field
indicating the currently usable bandwidth to transmit to the
station. Of course, make all drivers use it.
To achieve this, make ieee80211_ht_cap_ie_to_sta_ht_cap() get
the station as an argument, rather than the new capabilities,
so it can set up the new bandwidth field.
If the station is a VHT station and VHT bandwidth is in use,
also set the bandwidth accordingly.
Doing this allows us to get rid of the supports_40mhz flag as
the HT capabilities now reflect the true capability instead of
the current setting.
While at it, also fix ieee80211_ht_cap_ie_to_sta_ht_cap() to not
ignore HT cap overrides when MCS TX isn't supported (not that it
really happens...)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Like with HT, make things a bit simpler in future patches by
passing the station to ieee80211_vht_cap_ie_to_sta_vht_cap()
instead of the vht_cap pointer. Also disable VHT here if HT
isn't supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few mesh utility functions will call
ieee80211_bss_info_change_notify(), and then the caller
might notify the driver of the same change again. Avoid
this redundancy by propagating the BSS changes and
generally calling bss_info_change_notify() once per
change.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add command to trigger radar detection in the driver/FW.
Once radar detection is started it should continuously
monitor for radars as long as the channel active.
If radar is detected usermode notified with 'radar
detected' event.
Scanning and remain on channel functionality must be disabled
while doing radar detection/scanning, and vice versa.
Based on original patch by Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Scans currently work by stopping the netdev tx queues but leaving the
mac80211 queues active. This stops the flow of incoming packets while
still allowing mac80211 to transmit nullfunc and probe request frames to
facilitate scanning. However, the driver may try to wake the mac80211
queues while in this state, which will also wake the netdev queues.
To prevent this, add a new queue stop reason,
IEEE80211_QUEUE_STOP_REASON_OFFCHANNEL, to be used when stopping the tx
queues for off-channel operation. This prevents the netdev queues from
waking when a driver wakes the mac80211 queues.
This also stops all frames from being transmitted, even those meant to
be sent off-channel. Add a new tx control flag,
IEEE80211_TX_CTL_OFFCHAN_TX_OK, which allows frames to be transmitted
when the queues are stopped only for the off-channel stop reason. Update
all locations transmitting off-channel frames to use this flag.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the code assigns channel contexts to VLANs
(for use by the TX/RX code) when the AP master gets
its channel context assigned. This works fine, but
in the upcoming radar detection work the VLANs don't
require a channel context (during radar detection)
and assigning one to them anyway causes issues with
locking and also inconsistencies -- a VLAN interface
that is added before radar detection would get the
channel context, while one added during it wouldn't.
Fix these issues moving the channel context copying
to a new explicit operation that will not be used
in the radar detection code.
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using 'sizeof' on array given as function argument returns
size of a pointer rather than the size of array.
Cc: stable@vger.kernel.org
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add routines to
- maintain a PS mode for each peer and a non-peer PS mode
- indicate own PS mode in transmitted frames
- track neighbor STAs power modes
- buffer frames when neighbors are in PS mode
- add TIM and Awake Window IE to beacons
- release frames in Mesh Peer Service Periods
Add local_pm to sta_info to represent the link-specific power
mode at this station towards the remote station. When a peer
link is established, use the default power mode stored in mesh
config. Update the PS status if the peering status of a neighbor
changes.
Maintain a mesh power mode for non-peer mesh STAs. Set the
non-peer power mode to active mode during peering. Authenticated
mesh peering is currently not working when either node is
configured to be in power save mode.
Indicate the current power mode in transmitted frames. Use QoS
Nulls to indicate mesh power mode transitions.
For performance reasons, calls to the function setting the frame
flags are placed in HWMP routing routines, as there the STA
pointer is already available.
Add peer_pm to sta_info to represent the peer's link-specific
power mode towards the local station. Add nonpeer_pm to
represent the peer's power mode towards all non-peer stations.
Track power modes based on received frames.
Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS
neighbor counter and group-addressed frame buffer).
Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame
buffering routines in the tx path. Update num_sta_ps to buffer
and release group-addressed frames after DTIM beacons.
Announce the awake window duration in beacons if in light or
deep sleep mode towards any peer or non-peer. Create a TIM IE
similarly to AP mode and add it to mesh beacons. Parse received
Awake Window IEs and check TIM IEs for buffered frames.
Release frames towards peers in mesh Peer Service Periods. Use
the corresponding trigger frames and monitor the MPSP status.
Append a QoS Null as trigger frame if neccessary to properly end
the MPSP. Currently, in HT channels MPSPs behave imperfectly and
show large delay spikes and frame losses.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com>
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the default mesh beacon interval and DTIM period to cfg80211
and make them accessible to nl80211. This enables setting both
values when joining an MBSS.
Previously the DTIM parameter was not set by mac80211 so the
driver's default value was used.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The established peer link count is indicated in mesh beacons and
used for other internal tasks. Previously it was not updated when
authenticated peering is performed in userspace.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Acked-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow mesh interface to disable the power save which is by default
turn on in certain chipset. Testing with 2 units of ZCN-1523H-5-16
featuring AR9280 chipset which have power save enabled by default.
Constant reset if the average signal of the peer mesh STA is below
-80 dBm and power save is enabled.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During FT roaming, wpa_supplicant attempts to set the
key before association. This used to be rejected, but
as a side effect of my commit 66e67e4189
("mac80211: redesign auth/assoc") the key was accepted
causing hardware crypto to not be used for it as the
station isn't added to the driver yet.
It would be possible to accept the key and then add it
to the driver when the station has been added. However,
this may run into issues with drivers using the state-
based station adding if they accept the key only after
association like it used to be.
For now, revert to the behaviour from before the auth
and assoc change.
Cc: stable@vger.kernel.org
Reported-by: Cédric Debarge <cedric.debarge@acksys.fr>
Tested-by: Cédric Debarge <cedric.debarge@acksys.fr>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The following changes are invalid and should be
disallowed when a station already exists:
* supported rates changes, except for TDLS peers
* listen interval changes
* HT capability changes
Disallow them and also update a mac80211 comment
explaining how they would be racy.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Today, stations are added already associated. That is
inefficient if, for example, the driver has no room
for stations any more because then the station will
go through the entire auth/assoc handshake, only to
be kicked out afterwards.
To address this a bit better, at least with drivers
using the new station state callback, allow hostapd
to add stations in unauthenticated mode, just after
receiving the AUTH frame, before even replying. Thus
if there's no more space at that point, it can send
a negative auth frame back. It still needs to handle
later state transition errors though, of course.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of calculating in ieee80211_bss_info_change_notify()
whether beaconing should be enabled or not, set it in the
correct places in the callers. This simplifies the logic in
this function at the expense of offchannel, but is also more
robust.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there are VLANs, stopping an AP is inefficient as it
calls rcu_barrier() once for each interface (the VLANs
and the AP itself). Optimise this by moving rcu_barrier()
out of the station cleanups and calling it only once for
all interfaces combined.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When all interfaces have been removed, there can't
be any stations left over, so there's no need to
flush again. Remove this, and all code associated
with it, which also simplifies the function.
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[change to flush stations with AP flush in second loop]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the logic to fill a struct rate_info with
a STA's last RX rate is accessible only in the cfg.c.
As the RX rate calculation might be needed elsewhere,
split this out into a separate function.
Signed-off-by: Saravana <saravanad@posedge.com>
[fix various whitespace issues, reword commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the low-level driver wants to support P2P GO
powersave configuration, it must set the cfg80211
flags and mac80211 will pass the parameters to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To achieve this, limit the number of retries to
31 (instead of 255) and use the three bits that
are then free for VHT flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change nl80211 to support specifying a VHT (or HT)
using the control channel frequency (as before) and
new attributes for the channel width and first and
second center frequency. The old channel type is of
course still supported for HT.
Also change the cfg80211 channel definition struct
to support these by adding the relevant fields to
it (and removing the _type field.)
This also adds new helper functions:
- cfg80211_chandef_create to create a channel def
struct given the control channel and channel type,
- cfg80211_chandef_identical to check if two channel
definitions are identical
- cfg80211_chandef_compatible to check if the given
channel definitions are compatible, and return the
wider of the two
This isn't entirely complete, but that doesn't matter
until we have a driver using it. In particular, it's
missing
- regulatory checks on the usable bandwidth (if that
even makes sense)
- regulatory TX power (database can't deal with it)
- a proper channel compatibility calculation for the
new channel types
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.
Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.
Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers (e.g. wl12xx) might need to know the vif
to roc on (mainly in order to configure the
rx filters correctly).
Add the vif to the op params, and update the current
users (iwlwifi) to use the new api.
Signed-off-by: Eliad Peller <eliad@wizery.com>
[fix hwsim]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This new callback can be used to tune the rate to be used to send
multicast frames.
In the current state the multicast rate can be specified on IBSS/MESH
joining only. This makes it impossible to select a custom multicast
rate when then join command is sent by an external program (e.g.
wpa_supplicant)
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers are not expected to handle it before drv_start has been called. It
will be called again after an interface has been brought up.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of using the pointer which can be re-used
fairly quickly due to allocator patterns and then
makes debugging difficult, maintain a counter and
use its value. Since it's a 64-bit value it can't
really wrap, but catch that case anyway since it
most likely points to a bug somewhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even before channel contexts/multi-channel, having a
single global TX power limit was already problematic,
in particular if two managed interfaces connected to
two APs with different power constraints. The channel
context introduction completely broke this though and
in fact I had disabled TX power configuration there
for drivers using channel contexts.
Change everything to track TX power per interface so
that different user settings and different channel
maxima are treated correctly. Also continue tracking
the global TX power though for compatibility with
applications that attempt to configure the wiphy's
TX power globally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TX power setting is currently per wiphy (hardware
device) but with multi-channel capabilities that doesn't
make much sense any more.
Allow drivers (and mac80211) to advertise support for
per-interface TX power configuration. When the TX power
is configured for the wiphy, the wdev will be NULL and
the driver can still handle that, but when a wdev is
given the TX power can be set only for that wdev now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the driver, a lot of setup may be
necessary to start operating as an AP, some of
which may fail. Add an explicit AP start driver
method to make such failures easier to handle,
and add an AP stop driver method for symmetry.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since cfg80211 will now call the explicit stop_ap
operation when an AP interface goes down, move all
teardown code there and remove it from interface
handling. The only thing that needs to stay is the
code to dev_close() all dependent VLANs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the user wants to scan using a vif configured as AP,
cfg80211 must give him a chance to do it, even if this
will disrupt the stations performance due to off-channel
scanning. To do so, this patch adds a 'force' flag to the
SCAN_TRIGGER command which tells cfg80211 to perform the
scanning operation even if the vif is an AP and the
beaconing has already started.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a number of unused variables that gcc
pointed out (when building with W=1) as well as
some conditions that can never be true due to
the datatypes used: unsigned values can't be
less than zero. Remove this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On each channel that the device is operating on, it
may need to listen using one or more chains depending
on the SMPS settings of the interfaces using it. The
previous channel context changes completely removed
this ability (before, it was available as the SMPS
mode).
Add per-context tracking of the required static and
dynamic RX chains and notify the driver on changes.
To achieve this, track the chains and SMPS mode used
on each virtual interface and update the channel
context whenever this changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of operating on a single channel only,
use the new channel context infrastructure in
all mac80211 code.
This enables drivers that want to use the new
channel context infrastructure to use multiple
channels, while nothing should change for all
the other drivers that don't support it.
Right now this disables both TX power settings
and spatial multiplexing powersave. Both need
to be re-enabled on a channel context basis.
Additionally, when channel contexts are used
drop the connection when channel switch is
received rather than trying to handle it. This
will have to be improved later.
[With fixes from Eliad and Emmanuel incorporated]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the driver, channel contexts may be used or
not. If they are used, the driver must have support for
hardware scan and remain-on-channel; otherwise the driver
must not advertise support for multiple channels.
Also prohibit WDS type interfaces when channel contexts
are to be used as there's no clear definition of which
channel they use.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mark keys that might be used to receive management
frames so drivers can fall back on software crypto
for them if they don't support hardware offload.
As the new flag is only set correctly for RX keys
and the existing IEEE80211_KEY_FLAG_SW_MGMT flag
can only affect TX, also rename the latter to
IEEE80211_KEY_FLAG_SW_MGMT_TX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull in mac80211.git to let the next patch apply
without conflicts, also resolving a hwsim conflict.
Conflicts:
drivers/net/wireless/mac80211_hwsim.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Various small fixes for net/mac80211/cfg.c:mpath_set_pinfo():
Initialize *pinfo before filling members in, handle MESH_PATH_RESOLVED
correctly, and remove bogus assignment; result in correct display
of FLAGS values and meaningful EXPTIME for expired paths in iw utility.
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit mac80211: avoid using synchronize_rcu in ieee80211_set_probe_resp
changed the return value when the probe response template is not present.
Revert to the earlier value of 1 - this fixes AP mode for drivers like
ath9k.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After cfg80211 got a P2P Device abstraction, add
support to mac80211. Whether it really is supported
or not will depend on whether or not the driver has
support for it, but mac80211 needs to change to be
able to support drivers that need a P2P Device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This could take a while (100ms+) and may delay sending assoc resp
in AP mode with WPS or P2P GO (as setting the probe resp takes place
there). We've encountered situations where the delay was big enough
to cause connection problems with devices like Galaxy Nexus.
Switch to using call_rcu with a free handler.
[Arik - rework to use plain buffer and instead of skb]
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sending probe requests, e.g. during software scanning,
these will go out on the *current* channel, so their IEs
need to be built from the current channel. At other times,
e.g. for beacons or probe request templates, the IEs will
be used on the *operating* channel and using the current
channel instead might result in errors.
Add the appropriate parameters to respect the difference.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using hw.conf.channel is wrong as it could be the
temporary channel if any function like the beacon
get function is called while scanning or during
other temporary out-of-channel activities.
Use oper_channel instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, ps mode is indicated per device (rather than
per interface), which doesn't make a lot of sense.
Moreover, there are subtle bugs caused by the inability
to indicate ps change along with other changes
(e.g. when the AP deauth us, we'd like to indicate
CHANGED_PS | CHANGED_ASSOC, as changing PS before
notifying about disassociation will result in null-packets
being sent (if IEEE80211_HW_SUPPORTS_DYNAMIC_PS) while
the sta is already disconnected.)
Keep the current per-device notifications, and add
parallel per-vif notifications.
In order to keep it simple, the per-device ps and
the per-vif ps are orthogonal - the per-vif ps
configuration is determined only by the user
configuration (enable/disable) and the connection
state, and is not affected by other vifs state and
(temporary) dynamic_ps/offchannel operations
(unlike per-device ps).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When AP interface is going down, the stations
are flushed (in ieee80211_do_stop()) only after
the beaconing was stopped.
However, drivers might rely on stations being
removed before the beaconing was stopped, in
order to clean up properly.
Fix it by flushing the stations on ap stop.
(we already do the same for other interface
types, e.g. in ieee80211_set_disassoc())
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
commit "mac80211: unify SW/offload remain-on-channel"
moved the cookie assignment from ieee80211_mgmt_tx()
to ieee80211_start_roc_work(). But the latter is only
called where offchannel is needed. If offchannel isn't
needed/used, a uninitialized cookie value would be returned
to userspace.
This patch sets the cookie value when offchannel isn't used.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This essentially reverts commit 2e165b8184 but
introduces the get_channel operation with a new
wireless_dev argument so that you can retrieve
the channel per interface. This is necessary as
even though we can track all interface channels
(except monitor) we can't track the channel type
used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 870d37fc22.
This code doesn't work as cfg80211 will call
set_monitor_enabled at the wrong time and it
doesn't seem to be possible to fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new P2P Device will have to be able to scan for
P2P search, so move scanning to use struct wireless_dev
instead of struct net_device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to be able to create P2P Device wdevs, move
the virtual interface management over to wireless_dev
structures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The management frame and remain-on-channel APIs will be
needed in the P2P device abstraction, so move them over
to the new wdev-based APIs. Userspace can still use both
the interface index and wdev identifier for them so it's
backward compatible, but for the P2P Device wdev it will
be able to use the wdev identifier only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the AC parameters change, drivers might rely
on getting a bss_info_changed notification with
BSS_CHANGED_QOS in addition to the conf_tx call.
Always call the function when userspace updates
are made (in AP/GO modes) and also set the change
flag when updates were made by the AP (in managed
mode.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We do not need it anymore since cfg80211 tracks
monitor channel and monitor channel type.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use cfg80211 the new .set_monitor_enabled instead
of tracking it inside mac80211.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This and ieee80211_add_ext_srates_ie() aren't
exported, so can't be used by drivers anyway,
but there's also no reason that they should be
so make them private to mac80211 and use sdata
instead of vif arguments.
Acked-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
* a lot of messages should be pr_info, not pr_debug
* wholesale use of pr_debug makes it require *both*
Kconfig and dynamic configuration
* there are still a lot of ifdefs
* the style is very inconsistent, sometimes the
sdata->name is printed in front
Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Get current rssi (in dBm) from the driver/FW.
Instead of reporting the signal received in the last
rx packet, which might be inaccurate if rx traffic is
low and beacon filtering is enabled, get the signal
from the driver/FW.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a remain-on-channel item is deleted, we remove it
from the list and then start the next item. However,
if it wasn't actually the first item then calling
ieee80211_start_next_roc() is wrong as it will start
the first item -- even if that was already started.
Fix the two places that do this and add a warning to
prevent the problem from reoccurring.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Track userspace registrations for authentication
frames received on an IBSS interface. This field
will be used to decide whether or not to send
"open system" authentication frames when a new
station joins an adhoc network.
Signed-off-by: Will Hawkins <hawkinsw@opentechinstitute.org>
[redesign the code flow a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixes the wrong assignment of mesh element TTL.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As defined in section 13.10.9.3 Case D (802.11-2012), this
control variable is used to limit the mesh STA to send only
one PREQ to a root mesh STA within this interval of time
(in TUs). The default value for this variable is set to
2000 TUs. However, for current implementation, the maximum
configurable of dot11MeshHWMPconfirmationInterval is
restricted by dot11MeshHWMPactivePathTimeout.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mesh_path_root_timer is invoked once the dot11MeshHWMPRootMode
is larger than 1. This patch also adds the backward compatible
to the previous setting on dot11MeshHWMPRootMode. If the user
configures as follow, it will still trigger the proactive RANN
with Gate Announcement.
iw mesh0 set mesh_param mesh_hwmp_rootmode 1
iw mesh0 set mesh_param mesh_gate_announcements 1
similar to the following setting:
iw mesh0 set mesh_param mesh_hwmp_rootmode 4
iw mesh0 set mesh_param mesh_gate_announcements 1
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the mesh configuration parameters dot11MeshHWMProotInterval
and dot11MeshHWMPactivePathToRootTimeout to be used by
proactive PREQ mechanism.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If you add a monitor interface in parallel to a normal interface
mac80211 will let you to change the channel type on the monitor
interface even if you are connected. Add an explicit check to
disallow this.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
[fix typo in commit log, use sdata instead of netdev]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise, we might call the driver callback before
the interface was uploaded.
Solves the following warning:
WARNING: at net/mac80211/driver-ops.h:12 ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211]()
wlan0: Failed check-sdata-in-driver check, flags: 0x0
Modules linked in: wlcore_sdio wl12xx wl18xx wlcore mac80211 cfg80211 [last unloaded: cfg80211]
[<c001b964>] (unwind_backtrace+0x0/0x12c) from [<c0495550>] (dump_stack+0x20/0x24)
[<c0495550>] (dump_stack+0x20/0x24) from [<c003ee28>] (warn_slowpath_common+0x5c/0x74)
[<c003ee28>] (warn_slowpath_common+0x5c/0x74) from [<c003eefc>] (warn_slowpath_fmt+0x40/0x48)
[<c003eefc>] (warn_slowpath_fmt+0x40/0x48) from [<bf5c1ad0>] (ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211])
[<bf5c1ad0>] (ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211]) from [<bf575960>] (nl80211_set_tx_bitrate_mask+0x350/0x358 [cfg80211])
[<bf575960>] (nl80211_set_tx_bitrate_mask+0x350/0x358 [cfg80211]) from [<c03e9e94>] (genl_rcv_msg+0x1a8/0x1e8)
[<c03e9e94>] (genl_rcv_msg+0x1a8/0x1e8) from [<c03e9164>] (netlink_rcv_skb+0x5c/0xc0)
[<c03e9164>] (netlink_rcv_skb+0x5c/0xc0) from [<c03e9ce0>] (genl_rcv+0x28/0x34)
[<c03e9ce0>] (genl_rcv+0x28/0x34) from [<c03e8e74>] (netlink_unicast+0x158/0x234)
[<c03e8e74>] (netlink_unicast+0x158/0x234) from [<c03e93e0>] (netlink_sendmsg+0x218/0x298)
[<c03e93e0>] (netlink_sendmsg+0x218/0x298) from [<c03b4e5c>] (sock_sendmsg+0xa4/0xc0)
[<c03b4e5c>] (sock_sendmsg+0xa4/0xc0) from [<c03b5af4>] (__sys_sendmsg+0x1d8/0x254)
[<c03b5af4>] (__sys_sendmsg+0x1d8/0x254) from [<c03b5ca8>] (sys_sendmsg+0x4c/0x70)
[<c03b5ca8>] (sys_sendmsg+0x4c/0x70) from [<c0013980>] (ret_fast_syscall+0x0/0x3c)
Note that calling the driver can also result
in undefined behaviour since it doesn't have
to deal with calls while down.
Signed-off-by: Eliad Peller <eliad@wizery.com>
[removed timestamps, added note - Johannes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In my redesign of remain-on-channel I forgot
that an item could be cancelled when it's a
dependent item that is part of another item.
Allow cancelling such items by removing them
from the dependents list.
Note that when we cancel the main item, all
its dependents are also cancelled. It would
be possible to not do that, but would need
tricks to promote an item from dependent to
top-level and is tricky in the HW ROC case.
Reported-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan pointed out to me that ieee80211_start_next_roc()
already calls ieee80211_run_deferred_scan() if the list
of ROC items is empty, so there's no need to call it
again after calling ieee80211_start_next_roc().
Reported-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
fix the coding style related to mesh parameters, especially the indentation,
as pointed out by Johannes Berg.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Redesign all the off-channel code, getting rid of
the generic off-channel work concept, replacing
it with a simple remain-on-channel list.
This fixes a number of small issues with the ROC
implementation:
* offloaded remain-on-channel couldn't be queued,
now we can queue it as well, if needed
* in iwlwifi (the only user) offloaded ROC is
mutually exclusive with scanning, use the new
queue to handle that case -- I expect that it
will later depend on a HW flag
The bigger issue though is that there's a bad bug
in the current implementation: if we get a mgmt
TX request while HW roc is active, and this new
request has a wait time, we actually schedule a
software ROC instead since we can't guarantee the
existing offloaded ROC will still be that long.
To fix this, the queuing mechanism was needed.
The queuing mechanism for offloaded ROC isn't yet
optimal, ideally we should add API to have the HW
extend the ROC if needed. We could add that later
but for now use a software implementation.
Overall, this unifies the behaviour between the
offloaded and software-implemented case as much
as possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IDLE handling in HW off-channel is broken right
now since we turn off IDLE only when the off-channel
period already started. Therefore, all drivers that
use it today (only iwlwifi!) must support off-channel
while idle, so playing with idle isn't needed at all.
Off-channel in general, since it's no longer used for
authentication/association, shouldn't affect PS, so
also remove that logic.
Also document a small caveat for reporting TX status
from off-channel frames in HW remain-on-channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we've removed all uses of the set_channel
API except for the monitor channel and in libertas,
clarify this. Split the libertas mesh use into a
new libertas_set_mesh_channel() operation, just to
keep backward compatibility, and rename the normal
set_channel() to set_monitor_channel().
Also describe the desired set_monitor_channel()
semantics more clearly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just like the AP mode patch, instead of setting
the channel and then joining the mesh network,
provide the channel to join the network on to
the join_mesh() function.
Like in AP mode, you can also give the channel
to the join-mesh nl80211 command now.
Unlike AP mode, it picks a default channel if
none was given.
As libertas uses mesh mode interfaces but has
no join_mesh callback and we can't simply break
it, keep some compatibility code for that case
and configure the channel directly for it.
In the non-libertas case, where we store the
channel until join, allow setting it while the
interface is down.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of setting the channel first and then
starting the AP, let cfg80211 store the channel
and provide it as one of the AP settings.
This means that now you have to set the channel
before you can start an AP interface, but since
hostapd/wpa_supplicant always do that we're OK
with this change.
Alternatively, it's now possible to give the
channel as an attribute to the start-ap nl80211
command, overriding any preset channel.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the set_channel function up so it can be used
by other code in this file in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need for ieee80211_set_channel to check
whether a change in configuration happened since
ieee80211_hw_config() auto-detects it.
Additionally, it's wrong to pretend the HT config
for the BSS changed, it didn't, the BSS can't be
up & running (AP beaconing etc.) when the channel
type is changed anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Standardize the debugging to be able to use dynamic_debug.
Coalesce formats, align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 3a25a8c ("mac80211: add improved HW queue control")
added support for offchannel queue mapping. However, this
mapping is only valid when the driver supports
IEEE80211_HW_QUEUE_CONTROL.
Check whether the driver supports IEEE80211_HW_QUEUE_CONTROL
before setting the hw_queue to the mapped offchannel queue.
(This patch doesn't have any actual effect, because
hw_queue is overridden in ieee80211_tx() anyway,
so this is merely some cleanup)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using | with a constant is always true.
Likely this should have be &.
cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new mesh configuration parameter "ht_opmode" and will
allow user to check the current HT protection mode selected. Users could
configure the protection mode by the command "iw mesh_iface set mesh_param
mesh_ht_protection_mode=2". The default protection mode of mesh is set to
non-HT mixed mode.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The signal and noise are forced to be positive since ethtool
deals in unsigned 64-bit values and this number should be human
readable. This gives easy access to some of the data formerly
exposed in the deprecated /proc/net/wireless file.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds hooks to call into the driver to get additional
stats for the ethtool API.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lets ethtool print out stats related to stations
connected to the interface. Does not yet get stats
from the underlying driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moving a STA to an AP VLAN prevents num_mcast_sta from being decremented
once the STA leaves, because sta->sdata changes. Fix this by checking
for AP VLANs as well.
Also exclude 4-addr VLAN stations from num_mcast_sta - remote 4-addr
stations ignore 3-address multicast frames anyway. In a typical bridge
configuration they receive the same packets as 4-address unicast.
This patch also fixes clearing the sdata->u.vlan.sta pointer when the
STA is removed from a 4-addr VLAN.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the current channel is known, add frequency and channel type to
NL80211_CMD_GET_INTERFACE.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In WoWLAN, we only get the triggers when we actually get
to suspend. As a consequence, drivers currently don't
know that the device should enable wakeup. However, the
device_set_wakeup_enable() API is intended to be called
when the wakeup is enabled, not later when needed.
Add a new set_wakeup() call to cfg80211 and mac80211 to
allow drivers to properly call device_set_wakeup_enable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 currently only supports one hardware queue
per AC. This is already problematic for off-channel
uses since if we go off channel while the BE queue
is full and then try to send an off-channel frame
the frame will never go out. This will become worse
when we support multi-channel since then a queue on
one channel might be full, but we have to stop the
software queue for all channels. That is obviously
not desirable.
To address this problem allow drivers to register
more hardware queues, and allow them to map them to
virtual interfaces. When they stop a hardware queue
the corresponding AC software queues on the correct
interfaces will be stopped as well. Additionally,
there's an off-channel queue to solve that problem
and a per-interface after-DTIM beacon queue. This
allows drivers to manage software queues closer to
how the hardware works.
Currently, there's a limit of 16 hardware queues.
This may or may not be sufficient, we can adjust it
as needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AP netdev is really only active when beaconing, so
manage the carrier state accordingly. Also do that for
VLAN interfaces enslaved to a given AP interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Basic rates are added with supported rates IE and extended supported
rates IE.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report Toffset to userspace.
Let userspace select the mesh synchronization method.
Signed-off-by: Marco Porsch <marco.porsch@s2005.tu-chemnitz.de>
Signed-off-by: Pavel Zubarev <pavel.zubarev@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers that don't support QoS also don't support
setting up their ACs, catch that early. While at
it, remove the input check since cfg80211 does it
now.
Also fix up the restart code to not try to set up
the queues in this case.
Finally also change the tx_conf array to have
IEEE80211_NUM_ACS entries instead of # of queues
since that's what it really needs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the plan to change mac80211's queue API to
not map ACs to queues 1:1, it seems necessary to
clarify some APIs that act on ACs rather than on
queues to spell that out explicitly. Do this.
Also verify that the AC number given is valid.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Airtime link metric estimation was broken in HT mesh, use
cfg80211_calculate_bitrate to get the right rate value.
Also factor out tx rate copying from sta_set_sinfo().
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh peer links are established only if average rssi of the peer
candidate satisfies the threshold. This is not in 802.11s specification
but was requested by David Fulgham, an open80211s user. This is a way to avoid
marginal peer links with stations that are barely within range.
This patch adds a new mesh configuration parameter, mesh_rssi_threshold. This
feature is supported only for hardwares that report signal in dBm.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "cfg80211: no cookies in cfg80211_send_XXX()"
Holger Schurig removed the cookies in the calls
from mac80211 to cfg80211, but the ones in the
other direction were left in. Remove them now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AP/GO mode API isn't very clearly defined, it
has "set beacon" and "new beacon" etc.
Modify the API to the following:
* start AP -- all settings
* change beacon -- new beacon data
* stop AP -- stop AP mode operation
This also reflects in the nl80211 API, rename
the commands there correspondingly (but keep
the old names for compatibility.)
Overall, this makes it much clearer what's going
on in the API.
Kalle developed the ath6kl changes, I created
the rest of the patch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the second part of the auth/assoc redesign,
the mac80211 part. This moves the auth/assoc code
out of the work abstraction and into the MLME, so
that we don't flip channels all the time etc.
The only downside is that when we are associated,
we need to drop the association in order to create
a connection to another AP, but for most drivers
this is actually desirable and the ability to do
was never used by any applications. If we want to
implement resource reservation with FT-OTA, we'd
probably best do it with explicit R-O-C in wpa_s.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Handle MCS masks set by the user.
* Match rates provided by the rate control algorithm to the mask set,
also in HT mode, and switch back to legacy mode if necessary.
* add debugfs files to observate the rate selection
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the future, when we start notifying drivers,
state transitions could potentially fail. To make
it easier to distinguish between programming bugs
and driver failures:
* rename sta_info_move_state() to
sta_info_pre_move_state() which can only be
called before the station is inserted (and
check this with a new station flag).
* rename sta_info_move_state_checked() to just
plain sta_info_move_state(), as it will be
the regular function that can fail for more
than just one reason (bad transition or an
error from the driver)
This makes the programming model easier -- one of
the functions can only be called before insertion
and can't fail, the other can fail.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A mesh node that joins the mesh network is by default a forwarding entity. This patch allows
the mesh node to set as non-forwarding entity. Whenever dot11MeshForwarding is set to 0, the
mesh node can prevent itself from forwarding the traffic which is not destined to him.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to the previous beacon filtering patch,
make CQM RSSI support depend on the flags that
the driver set for virtual interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bail out if sta_apply_parameters() returns an error.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When userspace attempts to authorize a station
that is already authorized, nothing happens as
you'd expect. Similarly, when it unauthorizes
a station that is associated, nothing happens.
However, when it unauthorizes a station that
isn't even associated yet, we erroneously try
to move the station to associated. This seems
to happen occasionally as a result of a race
when wpa_supplicant attempts to unauthorize
the port in managed mode. Particularly with my
new patches to keep stations, it can then move
a station into ASSOCIATED state before we have
really associated, which is really confusing.
I introduced this bug in
"mac80211: refactor station state transitions"
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit a9b3cd7f32 (rcu: convert uses of rcu_assign_pointer(x, NULL) to
RCU_INIT_POINTER) did a lot of incorrect changes, since it did a
complete conversion of rcu_assign_pointer(x, y) to RCU_INIT_POINTER(x,
y).
We miss needed barriers, even on x86, when y is not NULL.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If station info contains a beacon loss count, return
it to userspace.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Station entries can have various states, the most
important ones being auth, assoc and authorized.
This patch prepares us for telling the driver about
these states, we don't want to confuse drivers with
strange transitions, so with this we enforce that
they move in the right order between them (back and
forth); some transitions might happen before the
driver even knows about the station, but at least
runtime transitions will be ordered correctly.
As a consequence, IBSS and MESH stations will now
have the ASSOC flag set (so they can transition to
AUTHORIZED), and we can get rid of a special case
in TX processing.
When freeing a station, unwind the state so that
other parts of the code (or drivers later) can rely
on the transitions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to use RCU here, we can just lock
the station mutex instead. This allows the code
to sleep, which is necessary for later patches.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is already checked in cfg80211, so no need
to repeat the checks here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nl80211 station handling code is a bit messy
and doesn't do a lot of validation. It seems like
this could be an issue for drivers that don't use
mac80211 to validate everything.
As cfg80211 doesn't keep station state, move the
validation of allowing supported_rates to change
for TDLS only in station mode to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As per 802.11mb 13.9.11.3
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains the processing changes in mac80211.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements ht-cap over-rides for mac80211 drivers.
HT may be disabled, making an /a/b/g/n station act like an
a/b/g station. HT40 may be disabled forcing the station to
be HT20 even if the AP and local hardware support HT40.
MAX-AMSDU may be disabled.
AMPDU-Density may be increased.
AMPDU-Factor may be decreased.
This has been successfully tested with ath9k using patched
wpa_supplicant and iw.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The warning is spurious -- if !sta we always exit without using the
unassigned qos variable, and if we do find the sta we assign it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow setting a probe response template for an interface operating in
AP mode. Low level drivers are notified about changes in the probe
response template and are able to retrieve a copy of the current probe
response. This data can, for example, be uploaded to hardware as a
template.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just add API to get the channel & report it. Trivial really.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize rate control algorithms only when supported rates are known
for a TDLS peer sta. Direct Tx between peers is not allowed before the
link is enabled. In turn, this only occurs after a change_station()
call that sets supported rates.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For probe responses it can be useful to not wait for ACK to
avoid retransmissions if the station that sent the probe is
already on the next channel, so allow userspace to request
not caring about the ACK with a new nl80211 flag.
Since mac80211 needs to be updated for the new function
prototype anyway implement it right away -- it's just a
few lines of code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support probing clients with null data frames
in AP mode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will allow us to support dynamic WEP with 802.1X
properly in mac80211 by not encrypting outgoing and
accepting unencrypted incoming frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's an extra pair of parentheses here that
is simply confusing because it implies a nesting
that doesn't actually exist. Just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to verify whether the command is successful before allocating
the station entry to avoid extra processing. This also fixes a memory
leak on the error path.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only station flags that are already defined in nl80211 are added for
now.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I introduced in-kernel off-channel TX I
introduced a bug -- the work can't be canceled
again because the code clear the skb pointer.
Fix this by keeping track separately of whether
TX status has already been reported.
Cc: stable@kernel.org [2.6.38+]
Reported-by: Jouni Malinen <j@w1.fi>
Tested-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flaglock in struct sta_info has long been
something that I wanted to get rid of, this
finally does the conversion to atomic bitops.
The conversion itself is straight-forward in
most places, a few things needed to change a
bit since we can no longer use multiple bits
at the same time.
On x86-64, this is a fairly significant code
size reduction:
text data bss dec hex
427861 23648 1008 452517 6e7a5 before
425383 23648 976 450007 6ddd7 after
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark the STA entries of enabled TDLS peers with a new "peer authorized"
flag.
During link setup, allow special TDLS setup frames through the AP, but
otherwise drop all packets destined to the peer. This is required by the
TDLS (802.11z) specification in order to prevent reordering of MSDUs
between the AP and direct paths.
When setup completes and the peer is authorized, send data directly,
bypassing the AP.
In the Rx path, allow data to be received directly from TDLS peers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When adding a TDLS peer STA, mark it with a new flag in both nl80211 and
mac80211. Before adding a peer, make sure the wiphy supports TDLS and
our operating mode is appropriate (managed).
In addition, make sure all peers are removed on disassociation.
A TDLS peer is first added just before link setup is initiated. In later
setup stages we have more info about peer supported rates, capabilities,
etc. This info is reported via nl80211_set_station().
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Register and implement the TDLS cfg80211 callback functions.
Internally prepare and send TDLS management frames. We incorporate
local STA capabilities and supported rates with extra IEs given by
usermode. The resulting packet is either encapsulated in a data frame,
or assembled as an action frame. It is transmitted either directly or
through the AP, as mandated by the TDLS specification.
Declare support for the TDLS external setup wiphy capability. This
tells usermode to handle link setup and discovery on its own, and use the
kernel driver for sending TDLS mgmt packets.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when hostapd sets the station as authorized
we also overwrite its uAPSD parameter. This obviously
leads to buggy behaviour (later, with my patches that
actually add uAPSD support). To fix this, only apply
those parameters if they were actually set in nl80211,
and to achieve that add a bitmap of things to apply.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
save and configure tx param per sdata, rather than
per hardware.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx params are currently configured per hw, although they
should be configured per interface.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever the scan request or tx_mgmt is requesting not to
use CCK rate for managemet frames through
NL80211_ATTR_TX_NO_CCK_RATE attribute, then mac80211 should
select appropriate least non-CCK rate. This could help to
send P2P probes and P2P action frames at non 11b rates
without diabling 11b rates globally.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new nl80211 attribute to specify whether to send the management
frames in CCK rate or not. As of now the wpa_supplicant is disabling
CCK rate at P2P init itself. So this patch helps to send P2P probe
request/probe response/action frames being sent at non CCK rate in 2GHz
without disabling 11b rates.
This attribute is used with NL80211_CMD_TRIGGER_SCAN and
NL80211_CMD_FRAME commands to disable CCK rate for management frame
transmission.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set SSID information from nl80211 beacon parameters. Advertise changes
in SSID to low level drivers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface is removed, the mesh paths associated with it should
also be removed.
This fixes a bug we observed when reloading a device driver module
without reloading mac80211s.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add uapsd_queues and max_sp fields to ieee80211_sta.
These fields might be needed by low-level drivers in
order to configure the AP.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since a v1 of the mesh gate series was accidentally applied, this patch
contains the changes in v2.
These are:
- automatically make mesh gate a root node.
- use TU_TO_EXP_TIME macro.
- initialize timer instead of checking for NULL timer function.
- cleanups.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to set NL80211_MESHCONF_GATE_ANNOUNCEMENTS attribute,
which will advertise this mesh node as being a mesh gate.
NL80211_HWMP_ROOTMODE must be set or this will do nothing.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to set Root Announcement Interval for our mesh
interface. Also, RANN interval is now in proper units of TUs.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For iwlwifi, I decided not to use this API since
it just increased the complexity for little gain.
Since nobody else intends to use it, let's kill
it again. If anybody later needs to have it, we
can always revive it then.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When assigning a NULL value to an RCU protected pointer, no barrier
is needed. The rcu_assign_pointer, used to handle that but will soon
change to not handle the special case.
Convert all rcu_assign_pointer of NULL value.
//smpl
@@ expression P; @@
- rcu_assign_pointer(P, NULL)
+ RCU_INIT_POINTER(P, NULL)
// </smpl>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tx_conf array to save the current tx queues
configuration, and reconfig it on resume (ieee80211_reconfig).
On resume, the driver is being reconfigured. Without
reconfiguring the tx queues as well, the driver might
configure the device to use wrong ac params (e.g. ps-poll
instead of uapsd).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just like TKIP and CCMP, CMAC has the PN race.
It might not actually be possible to hit it now
since there aren't multiple ACs for management
frames, but fix it anyway.
Also move scratch buffers onto the stack.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we can process multiple packets at the
same time for different ACs, but the PN is
allocated from a single counter, we need to
use an atomic value there. Use atomic64_t to
make this cheaper on 64-bit platforms, other
platforms will support this through software
emulation, see lib/atomic64.c.
We also need to use an on-stack scratch buf
so that multiple packets won't corrupt each
others scratch buffers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the necessary mac80211 APIs to support
GTK rekey offload, mirroring the functionality
from cfg80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a memeber to the ieee80211_sta structure to indicate whether the STA
supports WME.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds dump support to testmode. The testmode
dump support in nl80211 requires using two of the
six cb->args, the rest can be used by the driver
to figure out where the dump position is at or to
store other data across invocations.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These definitions need to be exposed now that we can set the peer link
states via NL80211_ATTR_STA_PLINK_STATE. They were already being
(opaquely) reported by NL80211_STA_INFO_PLINK_STATE.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds sparse RCU annotations to most of
mac80211, only the mesh code remains to be
done.
Due the the previous patches, the annotations
are pretty simple. The only thing that this
actually changes is removing the RCU usage of
key->sta in debugfs since this pointer isn't
actually an RCU-managed pointer (it only has
a single assignment done before the key even
goes live). As that is otherwise harmless, I
decided to make it part of this patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sched_scan_stopped was called by the driver, mac80211 calls
cfg80211, which in turn was calling mac80211 back with a flag
"driver_initiated". This flag was used so that mac80211 would do the
necessary cleanup but would not call the driver. This was enough to
prevent the bounce back between the driver and mac80211, but not
between mac80211 and cfg80211.
To fix this, we now do the cleanup in mac80211 before calling
cfg80211. To help with locking issues, the workqueue was moved from
cfg80211 to mac80211.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few configuration functions correctly do
rcu_read_lock() but don't correctly reference
some pointers protected by RCU. Fix that.
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code in ieee80211_del_key() doesn't acquire the
key_mtx properly when it dereferences the keys. It
turns out that isn't actually necessary since the
key_mtx itself seems to be redundant since all key
manipulations are done under the RTNL, but as long
as we have the key_mtx we should use it the right
way too.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
net/mac80211/cfg.c: In function ‘sta_apply_parameters’:
net/mac80211/cfg.c:746: error: ‘struct sta_info’ has no member named ‘plink_state’
make[1]: *** [net/mac80211/cfg.o] Error 1
make: *** [net/mac80211/mac80211.ko] Error 2
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement support for HW scheduled scan. The mac80211 code doesn't perform
scheduled scans itself, but calls the driver to start and stop scheduled
scans.
This patch also creates a trace event class to be used by drv_hw_scan
and the new drv_sched_scan_start and drv_sched_stop functions, in
order to avoid duplicate code.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a new configuration option to support AMPE from userspace.
Prior to this series we only supported authentication in userspace: an
authentication daemon would authenticate peer candidates in userspace
and hand them over to the kernel. From that point the mesh stack would
take over and establish a peer link (Mesh Peering Management).
These patches introduce support for Authenticated Mesh Peering Exchange
in userspace. The userspace daemon implements the AMPE protocol and on
successfull completion create mesh peers and install encryption keys.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds basic support for the new WoWLAN
configuration in mac80211. The behaviour is
completely offloaded to the driver though,
with two new callbacks (suspend/resume).
Options for the driver include a complete
reconfiguration after wakeup, and exposing
all the triggers it wants to support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is based on (but now quite far from) the
original work from Luis and Eliad. Add support
for configuring WoWLAN triggers, and getting
the configuration out again. Changes from the
original patchset are too numerous to list,
but one important change needs highlighting:
the suspend() callback is passed NULL for the
trigger configuration if userspace has not
configured WoWLAN at all.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a new API for setting a TX rate mask in
drivers that have rate control in either the firmware or hardware.
This can be used for various purposes, for example, masking out the
11b rates in P2P operation.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The locking with SMPS requests means that the
debugs file should lock the mgd mutex, not the
iflist mutex. Calls to __ieee80211_request_smps()
need to hold that mutex, so add an assertion.
This has always been wrong, but for some reason
never been noticed, probably because the locking
error only happens while unassociated.
Cc: stable@kernel.org [2.6.34+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add station connected time in debugfs. This will be helpful to get a
measure of stability of the connection and for debugging stress issues
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To NL80211_MESH_SETUP_IE. This reflects our ability to insert any ie
into a mesh beacon, not simply path selection ies.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows user-space monitoring of BSS parameters for the associated
station. This is useful for debugging and verifying that the paramaters
are as expected.
[Exactly the same as before but bundled into a single message]
Signed-off-by: Paul Stewart <pstew@chromium.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If dynamic_ps is disabled, enabling power save before the 4-way
handshake completes may delay the station from being authorized to
send/receive traffic, i.e. increase roaming times. It also may result in
a failed 4-way handshake depending on the AP's timing requirements and
beacon interval, and the station's listen interval.
To fix this, prevent power save from being enabled while the station
isn't authorized and recalculate power save whenever the station's
authorized state changes.
Signed-off-by: Jason Young <a.young.jason@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For devices supported by iwlwifi sometimes
off-channel transmissions need to be handled
by the device completely. To support this
mac80211 needs to pass the frame directly
to the driver and not through the TX path
as the driver needs the frame and channel
information at the same time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some were indirectly set to NO_HT (zero), but I think
it's better to explicitly set it in case the enum ever
changes. In cfg.c, it seems the channel-type was just
ignored (and thus always set to NO_HT).
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no point in disallowing scanning for a
GO interface when it's not beaconing yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we cannot set the channel type, set the channel back to the
original.
Don't update the driver hardware if nothing actually changed.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the off-channel TX is done with remain-on-channel
offloaded to hardware, the reported cookie is wrong as
in that case we shouldn't use the SKB as the cookie but
need to instead use the corresponding r-o-c cookie
(XOR'ed with 2 to prevent API mismatches).
Fix this by keeping track of the hw_roc_skb pointer
just for the status processing and use the correct
cookie to report in this case. We can't use the
hw_roc_skb pointer itself because it is NULL'ed when
the frame is transmitted to prevent it being used
twice.
This fixes a bug where the P2P state machine in the
supplicant gets stuck because it never gets a correct
result for its transmitted frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver has remain-on-channel offload,
implement off-channel transmission using that
primitive.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows drivers to support remain-on-channel
offload if they implement smarter timing or need
to use a device implementation like iwlwifi.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let path selection frames for protocols other than HWMP be sent to
userspace via NL80211_CMD_REGISTER_FRAME. Also allow userspace to send
and receive mesh path selection frames.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Userspace will now be allowed to toggle between the default path
selection algorithm (HWMP, implemented in the kernel), and a vendor
specific alternative. Also in the same patch, allow userspace to add
information elements to mesh beacons. This is accordance with the
Extensible Path Selection Framework specified in version 7.0 of the
802.11s draft.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh parameters can be to setup a mesh or to configure it.
This patch renames the ambiguous name mesh_params to mesh_config
in preparation for mesh_setup.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for split default keys (unicast
and multicast) in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to specify that a given key
is default only for unicast and/or multicast
transmissions. Only WEP keys are for both,
WPA/RSN keys set here are GTKs for multicast
only. For more future flexibility, allow to
specify all combiations.
Wireless extensions can only set both so use
nl80211; WEP keys (connect keys) must be set
as default for both (but 802.1X WEP is still
possible).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.
This uses the recently added generic EWMA library function.
--
v2: fix ABI breakage and change factor to be a power of 2.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of tying mesh activity to interface up,
add join and leave commands for mesh. Since we
must be backward compatible, let cfg80211 handle
joining a mesh if a mesh ID was pre-configured
when the device goes up.
Note that this therefore must modify mac80211 as
well since mac80211 needs to lose the logic to
start the mesh on interface up.
We now allow querying mesh parameters before the
mesh is connected, which simply returns defaults.
Setting them (internally renamed to "update") is
only allowed while connected. Specify them with
the new mesh join command instead where needed.
In mac80211, beaconing must now also follow the
mesh enabled/not enabled state, which is done
by testing the mesh ID.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 used to do all its bookkeeping in
the notifier, but some new stuff will have
to use local variables so make the callback
return the netdev pointer.
Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TTL in path selection information elements is different from
the mesh ttl used in mesh data frames. Version 7.03 of the 11s
draft calls this ttl 'Element TTL'.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements the new off-channel TX API
in mac80211 with a new work item type. The
operation doesn't add a new work item when
we're on the right channel and there's no
wait time so that for example p2p probe
responses will be transmitted without delay.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With p2p, it is sometimes necessary to transmit
a frame (typically an action frame) on another
channel than the current channel. Enable this
through the CMD_FRAME API, and allow it to wait
for a response. A new command allows that wait
to be aborted.
However, allow userspace to specify whether or
not it wants to allow off-channel TX, it may
actually want to use the same channel only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.
This uses the recently added generic EWMA library function.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow antenna configuration by calling driver's function for it.
We disallow antenna configuration if the wiphy is already running, mainly to
make life easier for 802.11n drivers which need to recalculate HT capabilites.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The lower driver is notified when the fragmentation threshold changes
and upon a reconfig of the interface.
If the driver supports hardware TX fragmentation, don't fragment
packets in the stack.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the frame registration notification, we
can see when probe requests are requested and
notify the low-level driver via filtering. The
flag is also set in AP and IBSS modes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some stats for /proc/net/wireless (and wext in general) are not
being set. This patch addresses a few of those with values easily
obtained from mac80211 core.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need for the WDS peer address
to not be const, so make it const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This information is already available in mac80211, we just need to export it
via cfg80211 and nl80211.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds API to allow adding per-station GTKs,
updates mac80211 to support it, and also allows
drivers to remove a key from hwaccel again when
this may be necessary due to multiple GTKs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The locking around ieee80211_recalc_smps is
buggy -- it cannot acquire another interface's
mutex while the iflist mutex is held because
another code path could be holding the iface
mutex and trying to acquire the iflist mutex.
But the locking is also unnecessary, we only
check "ifmgd->associated" as a bool, and don't
use the pointer (in check_mgd_smps).
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable management frame transmission and subscribing
to management frames through nl80211 in both cfg80211
and mac80211. Also update a few places that I forgot
to update for P2P-client mode previously, and fix a
small bug with non-action frames in this API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an refcounting bug. Previously it
was possible to corrupt the per-device recv. filter
and monitor management counters when:
iw dev wlanX set monitor [new flags]
was issued on an active monitor interface.
Acked-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a driver advertises p2p device support,
mac80211 will handle it, but internally it will
rewrite the interface type to STA/AP rather than
P2P-STA/GO since otherwise a lot of paths need
to be touched that are otherwise identical. A
p2p boolean tells drivers whether or not a given
interface will be used for p2p or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is modifying the station flags, and
as such should hold the flags lock so it can
do so atomically vs. other flags modifications
and readers. This issue was introduced when
this code was added in eccb8e8f, as it used
the wrong lock (thus not fixing the race that
was previously documented in a comment.)
Cc: stable@kernel.org [2.6.31+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support to mac80211 for changing the interface
type even when the interface is UP, if the driver
supports it.
To achieve this
* add a new driver callback for switching,
* split some of the interface up/down code out
into new functions (do_open/do_stop), and
* maintain an own __SDATA_RUNNING bit that will
not be set during interface type, so that any
other code doesn't use the interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the introduction of ieee80211_sdata_running(),
some new code was introduced that uses netif_running()
instead. Switch all these instances over.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers to specify their own set of cipher
suites to advertise vendor-specific ciphers. The
driver is then required to implement hardware
crypto offload for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a mac80211-based driver advertises mesh mode
support, this will be advertised to userspace.
However, if mac80211 was compiled without mesh
support, then that won't actually be true. Fix
this by removing the bit for mesh if mesh isn't
compiled in.
Since this synchronizes what we advertise to
cfg80211 and actually support, it means we can
now rely on cfg80211's interface type checks
and need not check again in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Standardize logging messages from
printk(KERN_<level> "%s: " fmt , wiphy_name(foo), args);
to
wiphy_<level>(foo, fmt, args);
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to register for more than just
action frames by giving the frame subtype, and
make it possible to use this in various modes
as well.
With some tweaks and some added functionality
this will, in the future, also be usable in AP
mode and be able to replace the cooked monitor
interface currently used in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When MFP is disabled, action frames will not
be encrypted since they are management frames
and the only management frames that can then
be encrypted are authentication frames.
Therefore, setting the don't-encrypt flag on
action frames is unnecessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, mac80211 translates the cfg80211
cipher suite selectors into ALG_* values.
That isn't all too useful, and some drivers
benefit from the distinction between WEP40
and WEP104 as well. Therefore, convert it
all to use the cipher suite selectors.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_add_key() currently returns -ENOMEM in case of any error,
including a missing crypto algorithm. Change ieee80211_key_alloc()
and ieee80211_aes_{key_setup_encrypt,cmac_key_setup}() to encode
errors with ERR_PTR() rather than returning NULL, and change
ieee80211_add_key() accordingly.
Compile-tested only.
Reported-by: Marcin Owsiany <porridge@debian.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Key locking simplification removed key->sdata != NULL verification from
ieee80211_key_free(). While that is fine for most use cases, there is one
path where this function can be called with an unlinked key (i.e.,
key->sdata == NULL && key->local == NULL). This results in a NULL pointer
dereference with the current implementation. This is known to happen at
least with FT protocol when wpa_supplicant tries to configure the key
before association.
Avoid the issue by passing in the local pointer to
ieee80211_key_free(). In addition, do not clear the key from hw_accel
or debugfs if it has not yet been added. At least the hw_accel one could
trigger another NULL pointer dereference.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Another remnant of the previous key locking scheme
needs to be removed -- this causes a warning
otherwise as ieee80211_set_default_mgmt_key will
acquire a mutex.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chun-Yeow Yeoh
Marco Porsch
Emmanuel Grumbach
Arik Nemtsov
Felix Fietkau
Simon Wunderlich
John W. Linville
David Spinadel
Johannes Berg
Thomas Pedersen
Johannes Berg
Antonio Quartulli
Ashok Nagarajan
Colleen Twitty
Bob Copeland
Marek Puzyniak
Karl Beldan
Janusz Dziedzic
Ilan Peer
Jouni Malinen
Seth Forshee
Cong Ding
Chun-Yeow Yeoh
Saravana
Eliad Peller
Antonio Quartulli
Mahesh Palivela
LEO Airwarosu Yoichi Shinoda
Sujith Manoharan
Eyal Shapira
Nicolas Cavallari
Michal Kazior
Victor Goldenshtein
Will Hawkins
Pontus Fuchs
Joe Perches
David S. Miller
Ben Greear
Javier Cardona
Eric Dumazet
Paul Stewart
Helmut Schaa
Jouni Malinen
Rajkumar Manoharan
Stephen Hemminger
Wey-Yi Guy
Luciano Coelho
Yogesh Ashok Powar
Sujith Manoharan
Mohammed Shafi Shajakhan
Jason Young
Bruno Randolf
Christian Lamparter
Ben Hutchings