Earlier BeagleBoards were using pad AH8 muxed to GPIO29 for MMC write-protect.
However, this signal has been changed to pad AG9 in board revision C2.
Fix this by adding mux configuration for pad AG9, runtime check for board
revisions and set the gpio number and pad muxing accordingly.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Original message:
The previous value of the jtag_id was set for the omap730. For the
omap850, this value is different, and this was causing
autodetection to fail.
Reported-by:
Cory Maccarrone <darkstar6262@gmail.com>
Angelo Arrifano <miknix@gmail.com>
Alistair Buxton <a.j.buxton@gmail.com>
Signed-off-by: Angelo Arrifano <miknix@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes these compiler warnings:
arch/arm/plat-omap/iovmm.c: In function 'vmap_sg':
arch/arm/plat-omap/iovmm.c:202: warning: passing argument 1 of
'flush_cache_vmap' makes integer from pointer without a cast
arch/arm/plat-omap/iovmm.c:202: warning: passing argument 2 of
'flush_cache_vmap' makes integer from pointer without a cast
arch/arm/plat-omap/iovmm.c: In function 'sgtable_fill_vmalloc':
arch/arm/plat-omap/iovmm.c:393: warning: passing argument 1 of
'flush_cache_vmap' makes integer from pointer without a cast
arch/arm/plat-omap/iovmm.c:393: warning: passing argument 2 of
'flush_cache_vmap' makes integer from pointer without a cast
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The only way to flush posted write to L4 bus is to do a read back
of the same register right after the write.
This seems to be mostly needed in interrupt handlers to avoid
causing spurious interrupts.
The earlier fix has been to mark the L4 bus as strongly ordered
memory, which solves the problem, but causes performance penalties.
Similar to the fix, 03803a71041e3bc3c077f4e7b92f6ceaa9426df3
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The softreset at startup is introduced as TRM describes and also some
register bit definitions are added instead of magic number.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO135 is used as EHCI (port2) phy reset pin on Multi Media Daughter card
connected to OMAP3EVM.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch 941132606c split IO_ADDRESS
into OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS except for the omap4
code to avoid merge conflicts with the omap4 code that was queued
earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to commit d136f1bd36,
there's a bug when unregistering a generic netlink family,
which is caught by the might_sleep() added in that commit:
BUG: sleeping function called from invalid context at net/netlink/af_netlink.c:183
in_atomic(): 1, irqs_disabled(): 0, pid: 1510, name: rmmod
2 locks held by rmmod/1510:
#0: (genl_mutex){+.+.+.}, at: [<ffffffff8138283b>] genl_unregister_family+0x2b/0x130
#1: (rcu_read_lock){.+.+..}, at: [<ffffffff8138270c>] __genl_unregister_mc_group+0x1c/0x120
Pid: 1510, comm: rmmod Not tainted 2.6.31-wl #444
Call Trace:
[<ffffffff81044ff9>] __might_sleep+0x119/0x150
[<ffffffff81380501>] netlink_table_grab+0x21/0x100
[<ffffffff813813a3>] netlink_clear_multicast_users+0x23/0x60
[<ffffffff81382761>] __genl_unregister_mc_group+0x71/0x120
[<ffffffff81382866>] genl_unregister_family+0x56/0x130
[<ffffffffa0007d85>] nl80211_exit+0x15/0x20 [cfg80211]
[<ffffffffa000005a>] cfg80211_exit+0x1a/0x40 [cfg80211]
Fix in the same way by grabbing the netlink table lock
before doing rcu_read_lock().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following trace pops up if we try to suspend with 3c59x ethernet NIC
brought down:
root@b1:~# ifconfig eth16 down
root@b1:~# echo mem > /sys/power/state
...
3c59x 0000:00:10.0: suspend
3c59x 0000:00:10.0: PME# disabled
Trying to free already-free IRQ 48
------------[ cut here ]------------
Badness at c00554e4 [verbose debug info unavailable]
NIP: c00554e4 LR: c00554e4 CTR: c019a098
REGS: c7975c60 TRAP: 0700 Not tainted (2.6.31-rc4)
MSR: 00021032 <ME,CE,IR,DR> CR: 28242422 XER: 20000000
TASK = c79cb0c0[1746] 'bash' THREAD: c7974000
...
NIP [c00554e4] __free_irq+0x108/0x1b0
LR [c00554e4] __free_irq+0x108/0x1b0
Call Trace:
[c7975d10] [c00554e4] __free_irq+0x108/0x1b0 (unreliable)
[c7975d30] [c005559c] free_irq+0x10/0x24
[c7975d40] [c01e21ec] vortex_suspend+0x70/0xc4
[c7975d60] [c017e584] pci_legacy_suspend+0x58/0x100
This is because the driver manages interrupts without checking for
netif_running().
Though, there are few other issues with suspend/resume in this driver.
The intention of calling free_irq() in suspend() was to avoid any
possible spurious interrupts (see commit 5b039e681b
"3c59x PM fixes"). But,
- On resume, the driver was requesting IRQ just after pci_set_master(),
but before vortex_up() (which actually resets 3c59x chips).
- Issuing free_irq() on a shared IRQ doesn't guarantee that a buggy
HW won't trigger spurious interrupts in another driver that
requested the same interrupt. So, if we want to protect from
unexpected interrupts, then on suspend we should issue disable_irq(),
not free_irq().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems recursion field from "struct ip_tunnel" is not anymore needed.
recursion prevention is done at the upper level (in dev_queue_xmit()),
since we use HARD_TX_LOCK protection for tunnels.
This avoids a cache line ping pong on "struct ip_tunnel" : This structure
should be now mostly read on xmit and receive paths.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver mapped only 128 bytes of the CAN controller address space when a
CPC-PCI v2 was detected (incl. CPC-104P). This patch will fix it by always
mapping the whole address space (4096 bytes on all boards) of the
corresponding PCI BAR.
Signed-off-by: Sebastian Haas <haas@ems-wuensche.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DOCPROC Documentation/DocBook/networking.xml
Warning(net/sunrpc/clnt.c:647): No description found for parameter 'req'
Warning(net/sunrpc/clnt.c:647): No description found for parameter 'tk_ops'
Warning(net/sunrpc/clnt.c:647): Excess function parameter 'ops' description in 'rpc_run_bc_task'
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Ricardo Labiaga <Ricardo.Labiaga@netapp.com>
Cc: Benny Halevy <bhalevy@panasas.com>
Cc: Andy Adamson <andros@netapp.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we ever implement this, then we can stop returning an error.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating a port number to a socket and hashing that socket shall be
an atomic operation with regards to other port allocation. Otherwise,
we could allocate a port that is already being allocated to another
socket.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous update did not resched in inner loop causing watchdogs.
Rewrite inner loop to:
* account for delays better with less clock calls
* more accurate timing of delay:
- only delay if packet was successfully sent
- if delay is 100ns and it takes 10ns to build packet then
account for that
* use wait_event_interruptible_timeout rather than open coding it.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to man page of setsockopt, if optlen is not valid, kernel should return
-EINVAL. But a simple testcase as following, errno is 0, which means setsockopt
is successful.
addr.s_addr = inet_addr("192.1.2.3");
setsockopt(s, IPPROTO_IP, IP_MULTICAST_IF, &addr, 1);
printf("errno is %d\n", errno);
Xiaotian Feng(dfeng@redhat.com) caught the bug. We fix it firstly checking
the availability of optlen and then dealing with the logic like other options.
Reported-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Acked-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
git commit 75c5158f70 converted the clocksource spinlock to a
mutex. This causes the following BUG:
BUG: sleeping function called from invalid context at
kernel/mutex.c:280 in_atomic(): 0, irqs_disabled(): 1, pid: 2473,
name: pm-suspend 2 locks held by pm-suspend/2473:
#0: (&buffer->mutex){......}, at: [<ffffffff8115ab13>]
sysfs_write_file+0x3c/0x137
#1: (pm_mutex){......}, at: [<ffffffff810865b5>]
enter_state+0x39/0x130 Pid: 2473, comm: pm-suspend Not tainted 2.6.31
#1 Call Trace:
[<ffffffff810792f0>] ? __debug_show_held_locks+0x22/0x24
[<ffffffff8104a2ef>] __might_sleep+0x107/0x10b
[<ffffffff8141fca9>] mutex_lock_nested+0x25/0x43
[<ffffffff81073537>] clocksource_resume+0x1c/0x60
[<ffffffff81072902>] timekeeping_resume+0x1e/0x1c8
[<ffffffff812aee62>] __sysdev_resume+0x25/0xcf
[<ffffffff812aef79>] sysdev_resume+0x6d/0xae
[<ffffffff810864f8>] suspend_devices_and_enter+0x12b/0x1af
[<ffffffff8108665b>] enter_state+0xdf/0x130
[<ffffffff81085dc3>] state_store+0xb6/0xd3
[<ffffffff81204c73>] kobj_attr_store+0x17/0x19
[<ffffffff8115abd2>] sysfs_write_file+0xfb/0x137
[<ffffffff811057d2>] vfs_write+0xae/0x10b
[<ffffffff81208392>] ? __up_read+0x1a/0x7f
[<ffffffff811058ef>] sys_write+0x4a/0x6e
[<ffffffff81011b82>] system_call_fastpath+0x16/0x1b
clocksource_resume is called early in the resume process, there is
only one cpu, no processes are running and the interrupts are
disabled. It is therefore possible to resume the clocksources
without taking the clocksource mutex.
Reported-by: Xiaotian Feng <xtfeng@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Tested-by: Michal Schmidt <mschmidt@redhat.com>
Cc: Xiaotian Feng <xtfeng@gmail.com>
Cc: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <20090924172952.49697825@mschwide.boeblingen.de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The memory barrier semantics of futex_wait_queue_me() are
non-obvious. Add some commentary to try and clarify it.
Signed-off-by: Darren Hart <dvhltc@us.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Dinakar Guniguntala <dino@in.ibm.com>
Cc: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <20090924185447.694.38948.stgit@Aeon>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
...it does the same thing as cifs_fill_fileinfo, but doesn't handle the
flist ordering correctly. Also rename cifs_fill_fileinfo to a more
descriptive name and have it take an open flags arg instead of just a
write_only flag. That makes the logic in the callers a little simpler.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
openat() is still a young glibc facility, better to not use it in a
non performance critical program (perf list)
Many machines have older glibc (RHEL 4 Update 5 -> glibc-2.3.4-2.36
on my dev machine for example).
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ulrich Drepper <drepper@redhat.com>
LKML-Reference: <4ABB767D.6080004@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Multicast joins can succeed even if the IB port is down. This happens
when the SM runs on the same port with the requesting port. However,
IPoIB calls netif_carrier_on() when the join of the broadcast group
succeeds, without caring about the state of the IB port. The result
is an IPoIB interface in RUNNING state but without an active IB port
to support it.
If a bonding interface uses this IPoIB interface as a slave it might
not detect that this slave is almost useless and failover
functionality will be damaged. The fix checks the state of the IB
port in the carrier_task before calling netif_carrier_on().
Adresses: https://bugs.openfabrics.org/show_bug.cgi?id=1726
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We forget to set nfs_server.protocol in tcp case when old-style binary
options are passed to mount. The thing remains zero and never validated
afterwards. As the result, we hit BUG in fs/nfs/client.c:588.
Breakage has been introduced in NFS: Add nfs_alloc_parsed_mount_data
merged yesterday...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
DOCPROC Documentation/DocBook/networking.xml
Warning(net/sunrpc/clnt.c:647): No description found for parameter 'req'
Warning(net/sunrpc/clnt.c:647): No description found for parameter 'tk_ops'
Warning(net/sunrpc/clnt.c:647): Excess function parameter 'ops' description in 'rpc_run_bc_task'
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Ricardo Labiaga <Ricardo.Labiaga@netapp.com>
Cc: Benny Halevy <bhalevy@panasas.com>
Cc: Andy Adamson <andros@netapp.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
catas_reset() uses a pointer to mthca_dev, but mthca_dev is not valid
after the call to __mthca_restart_one().
Based on a similar patch for mlx4 (634354d7, "mlx4: Fix access to
freed memory") by Vitaliy Gusev <vgusev@openvz.org>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is the fourth respin of the patch to convert oplock breaks to
use the slow_work facility.
A customer of ours was testing a backport of one of the earlier
patchsets, and hit a "Busy inodes after umount..." problem. An oplock
break job had raced with a umount, and the superblock got torn down and
its memory reused. When the oplock break job tried to dereference the
inode->i_sb, the kernel oopsed.
This patchset has the oplock break job hold an inode and vfsmount
reference until the oplock break completes. With this, there should be
no need to take a tcon reference (the vfsmount implicitly holds one
already).
Currently, when an oplock break comes in there's a chance that the
oplock break job won't occur if the allocation of the oplock_q_entry
fails. There are also some rather nasty races in the allocation and
handling these structs.
Rather than allocating oplock queue entries when an oplock break comes
in, add a few extra fields to the cifsFileInfo struct. Get rid of the
dedicated cifs_oplock_thread as well and queue the oplock break job to
the slow_work thread pool.
This approach also has the advantage that the oplock break jobs can
potentially run in parallel rather than be serialized like they are
today.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
ConnectX can work more efficiently if the CPU cache line size is passed
to it with the INIT_HCA firmware command.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The definition of nes_netdev_ops has initializations of a local function
and eth_mac_addr for its ndo_set_mac_address field. This change uses only
the local function.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier I, s, fld;
position p0,p;
expression E;
@@
struct I s =@p0 { ... .fld@p = E, ...};
@s@
identifier I, s, r.fld;
position r.p0,p;
expression E;
@@
struct I s =@p0 { ... .fld@p = E, ...};
@script:python@
p0 << r.p0;
fld << r.fld;
ps << s.p;
pr << r.p;
@@
if int(ps[0].line)!=int(pr[0].line) or int(ps[0].column)!=int(pr[0].column):
cocci.print_main(fld,p0)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (57 commits)
drm/i915: Handle ERESTARTSYS during page fault
drm/i915: Warn before mmaping a purgeable buffer.
drm/i915: Track purged state.
drm/i915: Remove eviction debug spam
drm/i915: Immediately discard any backing storage for uneeded objects
drm/i915: Do not mis-classify clean objects as purgeable
drm/i915: Whitespace correction for madv
drm/i915: BUG_ON page refleak during unbind
drm/i915: Search harder for a reusable object
drm/i915: Clean up evict from list.
drm/i915: Add tracepoints
drm/i915: framebuffer compression for GM45+
drm/i915: split display functions by chip type
drm/i915: Skip the sanity checks if the current relocation is valid
drm/i915: Check that the relocation points to within the target
drm/i915: correct FBC update when pipe base update occurs
drm/i915: blacklist Acer AspireOne lid status
ACPI: make ACPI button funcs no-ops if not built in
drm/i915: prevent FIFO calculation overflows on 32 bits with high dotclocks
drm/i915: intel_display.c handle latency variable efficiently
...
Fix up trivial conflicts in drivers/gpu/drm/i915/{i915_dma.c|i915_drv.h}
* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze: (24 commits)
microblaze: Disable heartbeat/enable emaclite in defconfigs
microblaze: Support simpleImage.dts make target
microblaze: Fix _start symbol to physical address
microblaze: Use LOAD_OFFSET macro to get correct LMA for all sections
microblaze: Create the LOAD_OFFSET macro used to compute VMA vs LMA offsets
microblaze: Copy ppc asm-compat.h for clean handling of constants in asm and C
microblaze: Actually show KiB rather than pages in "Freeing initrd memory:"
microblaze: Support ptrace syscall tracing.
microblaze: Updated CPU version and FPGA family codes in PVR
microblaze: Generate correct signal and siginfo for integer div-by-zero
microblaze: Don't be noisy when userspace causes hardware exceptions
microblaze: Remove ipc.h file which points to non-existing asm-generic file
microblaze: Clear sticky FSR register after generating exception signals
microblaze: Ensure CPU usermode is set on new userspace processes
microblaze: Use correct kbuild variable KBUILD_CFLAGS
microblaze: Save and restore msr in hw exception
microblaze: Add architectural support for USB EHCI host controllers
microblaze: Implement include/asm/syscall.h.
microblaze: Improve checking mechanism for MSR instruction
microblaze: Add checking mechanism for MSR instruction
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
module: don't call percpu_modfree on NULL pointer.
module: fix memory leak when load fails after srcversion/version allocated
module: preferred way to use MODULE_AUTHOR
param: allow whitespace as kernel parameter separator
module: reduce string table for loaded modules (v2)
module: reduce symbol table for loaded modules (v2)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (42 commits)
Btrfs: hash the btree inode during fill_super
Btrfs: relocate file extents in clusters
Btrfs: don't rename file into dummy directory
Btrfs: check size of inode backref before adding hardlink
Btrfs: fix releasepage to avoid unlocking extents we haven't locked
Btrfs: Fix test_range_bit for whole file extents
Btrfs: fix errors handling cached state in set/clear_extent_bit
Btrfs: fix early enospc during balancing
Btrfs: deal with NULL space info
Btrfs: account for space used by the super mirrors
Btrfs: fix extent entry threshold calculation
Btrfs: remove dead code
Btrfs: fix bitmap size tracking
Btrfs: don't keep retrying a block group if we fail to allocate a cluster
Btrfs: make balance code choose more wisely when relocating
Btrfs: fix arithmetic error in clone ioctl
Btrfs: add snapshot/subvolume destroy ioctl
Btrfs: change how subvolumes are organized
Btrfs: do not reuse objectid of deleted snapshot/subvol
Btrfs: speed up snapshot dropping
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
truncate: use new helpers
truncate: new helpers
fs: fix overflow in sys_mount() for in-kernel calls
fs: Make unload_nls() NULL pointer safe
freeze_bdev: grab active reference to frozen superblocks
freeze_bdev: kill bd_mount_sem
exofs: remove BKL from super operations
fs/romfs: correct error-handling code
vfs: seq_file: add helpers for data filling
vfs: remove redundant position check in do_sendfile
vfs: change sb->s_maxbytes to a loff_t
vfs: explicitly cast s_maxbytes in fiemap_check_ranges
libfs: return error code on failed attr set
seq_file: return a negative error code when seq_path_root() fails.
vfs: optimize touch_time() too
vfs: optimization for touch_atime()
vfs: split generic_forget_inode() so that hugetlbfs does not have to copy it
fs/inode.c: add dev-id and inode number for debugging in init_special_inode()
libfs: make simple_read_from_buffer conventional
* git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
lsm: Use a compressed IPv6 string format in audit events
Audit: send signal info if selinux is disabled
Audit: rearrange audit_context to save 16 bytes per struct
Audit: reorganize struct audit_watch to save 8 bytes
The general one handles NULL, the static obsolescent
(CONFIG_HAVE_LEGACY_PER_CPU_AREA) one in module.c doesn't; Eric's
commit 720eba31 assumed it did, and various frobbings since then kept
that assumption.
All other callers in module.c all protect it with an if; this effectively
does the same as free_init is only goto if we fail percpu_modalloc().
Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Cc: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Américo Wang <xiyou.wangcong@gmail.com>
Tested-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Normally the twisty paths of sysfs will free the attributes, but not if
we fail before we hook it into sysfs (which is the last thing we do in
load_module).
(This sysfs code is a turd, no doubt there are other issues lurking too).
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
For the longest time now we've been using multiple MODULE_AUTHOR()
statements when a module has more than one author, but the comment here
disagrees.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Some boot mechanisms require that kernel parameters are stored in a
separate file which is loaded to memory without further processing
(e.g. the "Load from FTP" method on s390). When such a file contains
newline characters, the kernel parameter preceding the newline might
not be correctly parsed (due to the newline being stuck to the end of
the actual parameter value) which can lead to boot failures.
This patch improves kernel command line usability in such a situation
by allowing generic whitespace characters as separators between kernel
parameters.
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Also remove all parts of the string table (referenced by the symbol
table) that are not needed for kallsyms use (i.e. which were only
referenced by symbols discarded by the previous patch, or not
referenced at all for whatever reason).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Discard all symbols not interesting for kallsyms use: absolute,
section, and in the common case (!KALLSYMS_ALL) data ones.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'for-linus' of git://neil.brown.name/md: (97 commits)
md: raid-1/10: fix RW bits manipulation
md: remove unnecessary memset from multipath.
md: report device as congested when suspended
md: Improve name of threads created by md_register_thread
md: remove sparse warnings about lock context.
md: remove sparse waring "symbol xxx shadows an earlier one"
async_tx/raid6: add missing dma_unmap calls to the async fail case
ioat3: fix uninitialized var warnings
drivers/dma/ioat/dma_v2.c: fix warnings
raid6test: fix stack overflow
ioat2: clarify ring size limits
md/raid6: cleanup ops_run_compute6_2
md/raid6: eliminate BUG_ON with side effect
dca: module load should not be an error message
ioat: driver version 4.0
dca: registering requesters in multiple dca domains
async_tx: remove HIGHMEM64G restriction
dmaengine: sh: Add Support SuperH DMA Engine driver
dmaengine: Move all map_sg/unmap_sg for slave channel to its client
fsldma: Add DMA_SLAVE support
...
Jarkko Nikula
Tony Lindgren
Angelo Arrifano
Sanjeev Premi
Hiroshi DOYU
Ajay Kumar Gupta
Johannes Berg
Anton Vorontsov
Eric Dumazet
Sebastian Haas
Jaswinder Singh Rajput
Rémi Denis-Courmont
Stephen Hemminger
Shan Wei
David S. Miller
Martin Schwidefsky
Darren Hart
Russell King
Roland Dreier
Jeff Layton
Moni Shoua
Al Viro
Jack Morgenstein
Eli Cohen
Julia Lawall
Linus Torvalds
Rusty Russell
Peter Oberparleiter
Jan Beulich