The MAX77802 PMIC has two 32.768kHz Buffered Clock Outputs with
Low Jitter Mode. This patch adds support for these two clocks.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Like most clock drivers, the Maxim 77686 PMIC clock binding
follows the convention that the "#clock-cells" property is
used to specify the number of cells in a clock provider.
But the binding document is not clear enough that it shall
be set to 1 since the PMIC support multiple clocks outputs.
Also, explain that the clocks identifiers are defined in a
header file that can be included by Device Tree source with
client nodes to avoid using magic numbers.
Finally, add "clock-output-names" as an optional property
since now is supported by the clock driver.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Clocks drivers for Maxim PMIC are very similar so they can
be converted to use the generic Maxim clock driver.
Also, while being there use module_platform_driver() helper
macro to eliminate more boilerplate code.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Maxim Integrated Power Management ICs are very similar with
regard to their clock outputs. Most of the clock drivers for
these chips are duplicating code and are simpler enough that
can be converted to use a generic driver to consolidate code
and avoid duplication.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds a dt-binding include for Maxim 77686
PMIC clock IDs that can be used by both the max77686
clock driver and Device Tree source files.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Since commit 54196ccbe0 (of: consolidate linker section OF match table
declarations) which went into 3.16-rc1 the following compiler warning is
generated:
In file included from drivers/clk/clk-efm32gg.c:12:0: include/linux/of.h:772:20:
warning: comparison of distinct pointer types lacks a cast [enabled by default]
.data = (fn == (fn_type)NULL) ? fn : fn }
^
include/linux/of.h:785:3: note: in expansion of macro '_OF_DECLARE'
_OF_DECLARE(table, name, compat, fn, of_init_fn_1)
^
include/linux/clk-provider.h:545:42: note: in expansion of macro 'OF_DECLARE_1'
#define CLK_OF_DECLARE(name, compat, fn) OF_DECLARE_1(clk, name, compat, fn)
^
drivers/clk/clk-efm32gg.c:81:1: note: in expansion of macro 'CLK_OF_DECLARE'
CLK_OF_DECLARE(efm32ggcmu, "efm32gg,cmu", efm32gg_cmu_init);
^
Fix it by making efm32gg_cmu_init return void.
Cc: Rob Herring <robh@kernel.org>
Reported-by: Bryan Hundven <bryanhundven@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Use __initconst instead of __initdata for constant init data.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
As checkpatch suggests:
WARNING: Possible unnecessary 'out of memory' message,
remove an error message after failing kmalloc() from the PLL driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
- Fix Kconfig menu structure
- Fix number of syscalls
- Fix compilation warnings from allmodconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlQO4a0ACgkQykllyylKDCE1NACeIFiXdvY7iy4UZyGMTHcdPnH9
o+kAn0v4x8eSaBRXtqYyxMc74US4Qu2N
=3RdC
-----END PGP SIGNATURE-----
Merge tag 'microblaze-3.17-rc5' of git://git.monstr.eu/linux-2.6-microblaze
Pull arch/microblaze fixes from Michal Simek:
- Kconfig menu structure fix
- fix number of syscalls
- fix compilation warnings from allmodconfig
* tag 'microblaze-3.17-rc5' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Fix number of syscalls
microblaze: Rename Advance setup to Kernel features
microblaze: Add mm/Kconfig to advance menu
arch/microblaze/include/asm/uaccess.h: Use pr_devel() instead of pr_debug()
arch/microblaze/include/asm/entry.h: Include "linux/linkage.h" to avoid compiling issue
Endpoint 0 should not be disabled, so we start loop counter from number 1.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes kernel panic/interrupt storm/etc issues if bootloader
left s3c-hsotg module in enabled state. Now interrupt handler is enabled
only after proper configuration of hardware registers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This leads to potential spinlock recursion in composite framework, other
udc drivers also don't call it directly from pullup method.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes possible freeze caused by infinite loop in interrupt
context.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the Generic PHY Framework a NULL phy is considered to be a valid phy
thus the "if (hsotg->phy)" check does not give us the information whether
the Generic PHY Framework is used.
In addition to the above this patch also removes phy_init from probe and
phy_exit from remove. This is not necessary when init/exit is done in the
s3c_hsotg_phy_enable/disable functions.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver is removed s3c_hsotg_phy_disable is called three times
instead of once. This results in decreasing of the phy reference counter
below zero and thus consecutive inserts of the module fails.
This patch removes calls to s3c_hsotg_phy_disable from s3c_hsotg_remove
and s3c_hsotg_udc_stop.
s3c_hsotg_udc_stop is called from udc-core.c only after
usb_gadget_disconnect, which in turn calls s3c_hsotg_pullup, which
already calls s3c_hsotg_phy_disable.
s3c_hsotg_remove must be called only after udc_stop, so there is no
point in disabling phy once again there.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a queue is registered, the block layer turns off the bypass
setting (because bypass is enabled when the queue is created). This
doesn't work well for queues that are unregistered and then registered
again; we get a WARNING because of the unbalanced calls to
blk_queue_bypass_end().
This patch fixes the problem by making blk_register_queue() call
blk_queue_bypass_end() only the first time the queue is registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Tejun Heo <tj@kernel.org>
CC: James Bottomley <James.Bottomley@HansenPartnership.com>
CC: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@fb.com>
On systems with special thermal configurations make sure we make
note of the thermal setup. This is required for proper firmware
configuration on these systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This commit activates the SSCG deviation correction for the Armada
370. It uses the optional function introduced by the commit "clk:
mvebu: Fix clk frequency value if SSCG is enabled".
Without this fix the deviation measured on a Mirabox was of a few
second each hour, whereas with this fix it was reduced at around
50ppm (around 4s per day).
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Leigh Brown <leigh@solinno.co.uk>
Link: https://lkml.kernel.org/r/1409645719-20003-3-git-send-email-gregory.clement@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the SSCG (Spread Spectrum Clock Generator) is enabled, it shifts
the frequency of the clock. The percentage is no more than 1% but when
the clock is used for a timer it leads to a clock drift.
This patch allows to correct the affected clock when the SSCG is
enabled. The check is done in an new optional function related to each
SoC: is_sscg_enabled(). The fix is done with the other new optional
function related to each SoC: fix_sscg_deviation. If one these
functions are not present then no correction is done on the clock
frequency.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Leigh Brown <leigh@solinno.co.uk>
Link: https://lkml.kernel.org/r/1409645719-20003-2-git-send-email-gregory.clement@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
There is no need to use hex_dump_to_buffer() since we have a kernel helper to
dump up to 64 bytes just via printk(). In our case the actual size is 15 bytes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
PM entries of LPSS power domain were not implemented correctly
in commit c78b083066 "ACPI / LPSS: custom power domain for LPSS".
This patch fixes and completes these PM entries.
Fixes: c78b083066 (ACPI / LPSS: custom power domain for LPSS)
Signed-off-by: Li Aubrey <aubrey.li@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit 232de51437 ("ACPI / battery: fix wrong value of
capacity_now reported when fully charged")
There is nothing wrong or unexpected about 'capacity_now' increasing above
the last 'full_charge_capacity' value. Different charging cycles will cause
'full_charge_capacity' to vary, both up and down. Good battery firmwares
will update 'full_charge_capacity' when the current charging cycle is
complete, increasing it if necessary. It might even go above
'design_capacity' on a fresh and healthy battery.
Capping 'capacity_now' to 'full_charge_capacity' is plain wrong, and
printing a warning if this doesn't happen to match the 'design_capacity'
is both annoying and terribly wrong.
This results in bogus warnings on perfectly working systems/firmwares:
[Firmware Bug]: battery: reported current charge level (39800) is higher than reported maximum charge level (39800).
and wrong values being reported for 'capacity_now' and
'full_charge_capacity' after the warning has been triggered.
Fixes: 232de51437 ("ACPI / battery: fix wrong value of capacity_now reported when fully charged")
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit d719870b41 ("ACPI / battery: Fix warning message in
acpi_battery_get_state()")
Capping 'capacity_now' to 'full_charge_capacity' is plain wrong. If this
is necessary to work around some buggy firmware, then the workaround needs
protection against being applied to working firmwares.
Good battery firmwares will allow 'capacity_now' to increase above
'full_charge_capacity', and will update the latter when the battery
is fully charged. By capping 'capacity_now' we lose accurate capacity
reporting until charging is complete whenever 'full_charge_capacity'
needs to be increased.
Fixes: d719870b41 ("ACPI / battery: Fix warning message in acpi_battery_get_state()")
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When DYNAMIC_DEBUG enabled, pr_debug() depends on KBUILD_MODNAME which
also depends on the modules number in Makefile. The related information
in "scripts/Makefile.lib" line 94:
# $(modname_flags) #defines KBUILD_MODNAME as the name of the module it will
# end up in (or would, if it gets compiled in)
# Note: Files that end up in two or more modules are compiled without the
# KBUILD_MODNAME definition. The reason is that any made-up name would
# differ in different configs.
For this case, 'radio-si470x-i2c.o' and 'radio-si470x-common.o' are in
one line, so cause compiling issue. And 'uaccess.h' is a common shared
header (not specially for drivers), so use pr_devel() instead of is OK.
The related error with allmodconfig:
CC [M] drivers/media/radio/si470x/radio-si470x-i2c.o
CC [M] drivers/media/radio/si470x/radio-si470x-common.o
In file included from include/linux/printk.h:257:0,
from include/linux/kernel.h:13,
from drivers/media/radio/si470x/radio-si470x.h:29,
from drivers/media/radio/si470x/radio-si470x-common.c:115:
./arch/microblaze/include/asm/uaccess.h: In function 'access_ok':
include/linux/dynamic_debug.h:66:14: error: 'KBUILD_MODNAME' undeclared (first use in this function)
.modname = KBUILD_MODNAME, \
^
include/linux/dynamic_debug.h:76:2: note: in expansion of macro 'DEFINE_DYNAMIC_DEBUG_METADATA'
DEFINE_DYNAMIC_DEBUG_METADATA(descriptor, fmt); \
^
include/linux/printk.h:263:2: note: in expansion of macro 'dynamic_pr_debug'
dynamic_pr_debug(fmt, ##__VA_ARGS__)
^
./arch/microblaze/include/asm/uaccess.h:101:3: note: in expansion of macro 'pr_debug'
pr_debug("ACCESS fail: %s at 0x%08x (size 0x%x), seg 0x%08x\n",
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
"entry.h" needs 'asmlinkage', and "asm/linkage.h" does not provide it.
So need include "linux/linkage.h" to use generic one instead of.
The related error (with allmodconfig under microblaze):
CC [M] drivers/net/ethernet/emulex/benet/be_main.o
In file included from ./arch/microblaze/include/asm/processor.h:17:0,
from include/linux/prefetch.h:14,
from drivers/net/ethernet/emulex/benet/be_main.c:18:
./arch/microblaze/include/asm/entry.h:33:19: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'void'
extern asmlinkage void do_notify_resume(struct pt_regs *regs, int in_syscall);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch wires up three new syscalls for powerpc. The three
new syscalls are seccomp, getrandom and memfd_create.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
CONFIG_FHANDLE is a requirement for systemd and with the increasing
uptake of systemd within distros it makes sense for 64 bit defconfigs
to include it.
Signed-off-by: Cyril Bur <cyril.bur@au1.ibm.com>
As opal_message_init() uses machine_early_initcall(powernv, ), and
opal_hmi_handler_init() depends on that early initcall, so it also needs
use machine_* to check the machine_id.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
ABIv2 kernels are failing to backtrace through the kernel. An example:
39.30% readseek2_proce [kernel.kallsyms] [k] find_get_entry
|
--- find_get_entry
__GI___libc_read
The problem is in valid_next_sp() where we check that the new stack
pointer is at least STACK_FRAME_OVERHEAD below the previous one.
ABIv1 has a minimum stack frame size of 112 bytes consisting of 48 bytes
and 64 bytes of parameter save area. ABIv2 changes that to 32 bytes
with no paramter save area.
STACK_FRAME_OVERHEAD is in theory the minimum stack frame size,
but we over 240 uses of it, some of which assume that it includes
space for the parameter area.
We need to work through all our stack defines and rationalise them
but let's fix perf now by creating STACK_FRAME_MIN_SIZE and using
in valid_next_sp(). This fixes the issue:
30.64% readseek2_proce [kernel.kallsyms] [k] find_get_entry
|
--- find_get_entry
pagecache_get_page
generic_file_read_iter
new_sync_read
vfs_read
sys_read
syscall_exit
__GI___libc_read
Cc: stable@vger.kernel.org # 3.16+
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Values acquired from Open Firmware are in 32-bit big endian format
and need to be handled on little endian architectures. This patch
ensures values are in cpu endian when hotplugging memory.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
The tx_empty() callback currently checks the TXEMPTY bit in the interrupt
status register to decided whether the FIFO should be reported as empty or
not. The bit in this register gets set when the FIFO state transitions from
non-empty to empty but is cleared again in the interrupt handler. This means
it is not suitable to be used to decided whether the FIFO is currently empty
or not. Instead use the TXEMPTY bit from the status register which will be
set as long as the FIFO is empty.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In set_termios(), interrupts where not disabled if UART_ENABLE_MS() was
false.
Tested on at91sam9g35.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org> # >= 3.16
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Another new ACPI identifier for the 8250 dw bindings to cover newer Intel
SoCs such as Braswell.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the uwb_dev->bce entry is set before calling uwb_dev_add in
uwbd_dev_onair so that usermode will only see the device after it is
properly initialized. This fixes a kernel panic that can occur if
usermode tries to access the IEs sysfs attribute of a UWB device before
the driver has had a chance to set the beacon cache entry.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull ext4 bugfix from Ted Ts'o.
[ Hmm. It's possible we should make kfree() aware of error pointers,
and use IS_ERR_OR_NULL rather than a NULL check. But in the meantime
this is obviously the right fix. - Linus ]
* 'for_linus_urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: avoid trying to kfree an ERR_PTR pointer
Pull nfsd bugfixes from Bruce Fields:
"A couple minor nfsd bugfixes"
* 'for-3.17' of git://linux-nfs.org/~bfields/linux:
lockd: fix rpcbind crash on lockd startup failure
nfsd4: fix rd_dircount enforcement
Use the correct register address for Calibration Active and Interrupt
Enable.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I've not done a full audit of all mouse drivers, I noticed these ones were
missing the POINTER property while working on the POINTING_STICK property.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is useful for userspace to know that there not dealing with a regular
mouse but rather with a pointing stick (e.g. a trackpoint) so that
userspace can e.g. automatically enable middle button scrollwheel
emulation.
It is impossible to tell the difference from the evdev info without
resorting to putting a list of device / driver names in userspace, this is
undesirable.
Add a property which allows userspace to see if a device is a pointing
stick, and set it on all the pointing stick drivers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch corrects a lack of testing.
If fw is NULL when calling firmware_load(), it results in a kernel oops.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d24d481b7d (usb-storage: Modify and export adjust_quirks so
that it can be used by uas) added the 'u' flag to the quirks module
parameter for usb-storage, but neglected to update the
documentation. This patch adds the documentation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org> # 3.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Javier Martinez Canillas
Uwe Kleine-König
Soren Brinkmann
Linus Torvalds
Robert Baldyga
Marek Szyprowski
Kamil Debski
Alan Stern
Alex Deucher
Gregory CLEMENT
Andy Shevchenko
Fu Zhonghui
Bjørn Mork
Michal Simek
Chen Gang
Pranith Kumar
Cyril Bur
Li Zhong
Anton Blanchard
Thomas Falcon
Jeff Layton
Cong Wang
Lars-Peter Clausen
Richard Genoud
Alan Cox
Thomas Pugliese
Taylor Braun-Jones
Klaus Goger
Hans de Goede
Jean-Michel Hautbois