Fix typo: s/resouces/resources/ in a pr_debug
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Axon MSI driver depends on more than just PCI_MSI, so add a
Kconfig fragment for it. Fixes randconfig build failures.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There's no way for us to express to firmware that we want a
discontiguous, or non-zero based, range of MSI-X entries. So we
must reject such requests.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
So at least you can see what kernel you're booting if you die
before the kernel prints it mid-way through start_kernel().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch enables oprofile for all 3 FX variants and GX variant of the
750 processor.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to offset by *pos bytes, not *pos words.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Based on an original patch from Roel Kluin <roel.kluin@gmail.com>.
The write size calculated during regs and fpcr writes may currently
go negative. Because size is unsigned, this will wrap, and our
check for EFBIG will fail.
Instead, do the check for EFBIG before subtracting from size.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Change the ps3av_auto_videomode() mode id argument type from unsigned to
signed so a negative id can be detected and reported as an -EINVAL failure.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To help users diagnose hotpug memory problems, change the
printing of memory hotplug errors from DBG() to pr_err().
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc 64 bit architecture defines three flags for the
DABR (Data Address Breakpoint Register). Add definitions
for the currently missing DABR_DATA_WRITE and DABR_DATA_READ
flags to the powerpc reg.h file.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add macros for the GS (guest state) bit to the list of MSR bit definitions.
On PowerPC cores that support embedded hypervisor mode, GS is cleared if
the system is running in hypervisor state (and MSR[PR] is cleared), and set
if it's running in guest state. See the Power ISA 2.06 specification for
more information.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For ppc750 processors which use 4 performance counters instead of the
6 G4 uses but otherwise is compatible with G4.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
spuctx_switch_state() warns if ktime goes backwards, but it
sometimes compares an uninitialized value, which showed that
the data was unreliable when we actually saw the warning.
Initialize it to the current time in order to get correct data.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When identify_cpu() is called a second time with a logical PVR, it
only copies a subset of the cpu_spec fields so as to avoid overwriting
the performance monitor fields that were initialized based on the
real PVR.
However some of the other, non performance monitor related fields are
also not copied:
* pvr_mask
* pvr_value
* mmu_features
* machine_check
The fact that pvr_mask is not copied can result in show_cpuinfo()
showing the cpu as "unknown", if we override an unknown PVR with a
logical one - as reported by Shaggy.
So change the logic to copy all fields, and then put back the PMC
related ones in the case that we're overwriting a real PVR with a
logical one.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The for-loop body of identify_cpu() has gotten a little big, so move the
loop body logic into a separate function. No other changes.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds the necessary bits and pieces to powerpc implementation of
ioremap to benefit from caller tracking in /proc/vmallocinfo, at least
for ioremap's done after mem init as the older ones aren't tracked.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Setting G5's cpu frequency transition latency to CPUFREQ_ETERNAL stops
ondemand governor from working. I measured the latency using sched_clock
and haven't seen much higher than 11000ns, so I set this to 12000ns for
my configuration. Possibly other configurations will be different?
Ideally the generic code would be able to measure it in case the platform
does not provide it.
But this simple patch at least makes it throttle again.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This reverts commit e088e4c9cd.
Removing the sysfs interface for p4-clockmod was flagged as a
regression in bug 12826.
Course of action:
- Find out the remaining causes of overheating, and fix them
if possible. ACPI should be doing the right thing automatically.
If it isn't, we need to fix that.
- mark p4-clockmod ui as deprecated
- try again with the removal in six months.
It's not really feasible to printk about the deprecation, because
it needs to happen at all the sysfs entry points, which means adding
a lot of strcmp("p4-clockmod".. calls to the core, which.. bleuch.
Signed-off-by: Dave Jones <davej@redhat.com>
The registers for the local bus are incorrectly set to 0xf8005000 rather
than there actual location of 0xfef05000.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
p54: fix race condition in memory management
cfg80211: test before subtraction on unsigned
iwlwifi: fix error flow in iwl*_pci_probe
rt2x00 : more devices to rt73usb.c
rt2x00 : more devices to rt2500usb.c
bonding: Fix device passed into ->ndo_neigh_setup().
vlan: Fix vlan-in-vlan crashes.
net: Fix missing dev->neigh_setup in register_netdevice().
tmspci: fix request_irq race
pkt_sched: act_police: Fix a rate estimator test.
tg3: Fix 5906 link problems
SCTP: change sctp_ctl_sock_init() to try IPv4 if IPv6 fails
IPv6: add "disable" module parameter support to ipv6.ko
sungem: another error printed one too early
aoe: error printed 1 too early
net pcmcia: worklimit reaches -1
net: more timeouts that reach -1
net: fix tokenring license
dm9601: new vendor/product IDs
netlink: invert error code in netlink_set_err()
...
The Freescale Serial Synchronous Interface (SSI) is an audio device present on
some Freescale SOCs. Various implementations of the SSI have a different
transmit and receive FIFO depth, but are otherwise identical. To support
these variations, add a new property fsl,fifo-depth to the SSI node that
specifies the depth of the FIFOs.
Also update the MPC8610 HPCD device tree with this property.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The e500mc core supports the new tlbilx instructions that do core
local invalidates and also provide us the ability to take down
all TLB entries matching a given PID.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On MPC837X CPUs Dual-Role USB isn't always available (for example DR
USB pins can be muxed away to eSDHC).
U-Boot adds status = "disabled" property into the DR USB nodes to
indicate that we must not try to configure or probe Dual-Role USB,
otherwise we'll break eSDHC support on targets with MPC837X CPUs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The interrupt pending register is write 1 clear. If there are more than
one external interrupts pending at the same time, acking the first
interrupt by reading pending register then OR the corresponding bit and
write back to pending register will also clear other interrupt pending
bits. That will cause loss of interrupt.
Signed-off-by: Da Yu <dayu@datangmobile.cn>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Impact: remove lots of lguest boot WARN_ON() when CONFIG_SPARSE_IRQ=y
We now need to call irq_to_desc_alloc_cpu() before
set_irq_chip_and_handler_name(), but we can't do that from init_IRQ (no
kmalloc available).
So do it as we use interrupts instead. Also means we only alloc for
irqs we use, which was the intent of CONFIG_SPARSE_IRQ anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
Impact: fix lguest boot crash on modern Intel machines
The code in early_init_intel does:
if (c->x86 > 6 || (c->x86 == 6 && c->x86_model >= 0xd)) {
u64 misc_enable;
rdmsrl(MSR_IA32_MISC_ENABLE, misc_enable);
And that rdmsr faults (not allowed from non-0 PL). We can get around
this by mugging the family ID part of the cpuid. 5 seems like a good
number.
Of course, this is a hack (how very lguest!). We could just indicate
that we don't support MSRs, or implement lguest_rdmst.
Reported-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: Patrick McHardy <kaber@trash.net>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, pebs: correct qualifier passed to ds_write_config() from ds_request_pebs()
x86, bts: remove bad warning
x86: add Dell XPS710 reboot quirk
x86, math-emu: fix init_fpu for task != current
x86: EFI: Back efi_ioremap with init_memory_mapping instead of FIX_MAP
x86: fix DMI on EFI
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (28 commits)
Blackfin arch: SPI_MMC is now mainlined MMC_SPI
Blackfin arch: disable legacy /proc/scsi/ support by default
Blackfin arch: remove duplicated ANOMALY_05000448 ifdef check
Blackfin arch: add stubs for anomalies 447 and 448
Blackfin arch: cleanup bfin_sport.h header and export it to userspace
Blackfin arch: fix bug - gdb signull case make trunk kernel panic frequently
Blackfin arch: remove spurious dash when dcache is off
Blackfin arch: mark init_pda as __init as only __init funcs all it
Blackfin arch: fix bug - On bf548-ezkit, ethernet fails to work after wakeup from "mem"
Blackfin arch: Random read/write errors are a bad thing
Blackfin arch: update default kernel config, select KSZ8893M driver for BF518
Blackfin arch: Fix bug - KGDB single step into the middle of a 4 bytes instruction on bf561 after soft bp is hit
Blackfin arch: Fix bug - make ksz8893m driver available when bfin_mac is enabled
Blackfin arch: make sure people do not set the kernel load address too high
Blackfin arch: fix bug - The SPORT_HYS bit is not set for BF561 0.5
Blackfin arch: update anomaly sheets to match latest public info
Blackfin arch: Fix BUG - kernel fails to build in pm.c when allow wakeup fromi standby by GPIO
Blackfin arch: PM_BFIN_WAKE_GP: update help
Blackfin arch: fix bug - kgdb fails to continue after setting breakpoint on bf561-ezkit kernel with smp patch
Blackfin arch: Enable Write Back Cache on all Blackfin Boards
...
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ata: add CFA specific identify data words
remove stale comment from <linux/hdreg.h>
AT91: initialize Compact Flash on AT91SAM9263 cpu
ide: add at91_ide driver
ide: allow to wrap interrupt handler
ide-iops: fix odd-length ATAPI PIO transfers
ide: NULL noise: drivers/ide/ide-*.c
ide: expiry() returns int, negative expiry() return values won't be noticed
This is a build fix required after "x86-64: seccomp: fix 32/64 syscall
hole" (commit 5b1017404a). MIPS doesn't
have the issue that was fixed for x86-64 by that patch.
This also doesn't solve the N32 issue which is that N32 seccomp processes
will be treated as non-compat processes thus only have access to N64
syscalls.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We recently discovered a problem with passing of DMA attributes on SN
systems with the older PIC chips.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jeremy Higdon <jeremy@sgi.com>
Cc: <habeck@sgi.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch updates the Xilinx ML507 device tree to match the released
ML507 powerpc reference design (ml507_ppc440_emb_ref). This patch is
needed to boot Linux on the ML507 powerpc reference design without
manually generating and tweaking a device tree from the project directory.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
ds_write_config() can write the BTS as well as the PEBS part of
the DS config. ds_request_pebs() passes the wrong qualifier, which
results in the wrong configuration to be written.
Reported-by: Stephane Eranian <eranian@googlemail.com>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
LKML-Reference: <20090305085721.A22550@sedona.ch.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In case a ptraced task is reaped (while the tracer is still attached),
ds_exit_thread() is called before ptrace_exit(). The latter will
release the bts_tracer and remove the thread's ds_ctx.
The former will WARN() if the context is not NULL.
Oleg Nesterov submitted patches that move ptrace_exit() before
exit_thread() and thus reverse the order of the above calls.
Remove the bad warning. I will add it again when Oleg's changes are in.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
LKML-Reference: <20090305084954.A22000@sedona.ch.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Andrew Victor <avictor.za@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is IDE host driver for AT91 (SAM9, CAP9, AT572D940HF) Static Memory
Controller with Compact Flash True IDE Mode logic.
Driver have to switch 8/16 bit bus width when accessing Task Tile or Data
Register. Moreover some extra things need to be done when setting PIO mode.
Only PIO mode is used, hardware have no DMA support. If interrupt line is
connected through GPIO extra quirk is needed to cope with fake interrupts.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Andrew Victor <avictor.za@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use copy_to_user_page and copy_from_user_page instead of
memcpy. copy_to_user_page does cache flush when necessary.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
