Commit Graph

40 Commits

Author SHA1 Message Date
Viresh Kumar ea505bc99f spi/pl022: Allow request for higher frequency than maximum possible
Currently, if we request for frequency greater than maximum possible, spi driver
returns error.

For example, if the spi block src frequency is 333/4 MHz, i.e. 83.33.. MHz,
maximum frequency programmable would be src/2. Which would come around 41.6...

It is difficult to pass frequency in these figures. We normally try to program
in round figures, like 42 MHz and it should get programmed to <=
requested_frequency, i.e. 41.6...

For this to happen, we must not return error even if requested freq is higher
than max possible. But should program it to max possible.

Reported-by: Vinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2012-04-27 12:07:40 -06:00
Viresh Kumar 5eb806a3a6 spi/pl022: Fix calculate_effective_freq()
calculate_effective_freq() was still not optimized and there were cases when it
returned without error and with values of cpsr and scr as zero.

Also, the variable named found is not used well.

This patch targets to optimize and correct this routine. Tested for SPEAr.

Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Vinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2012-04-27 10:47:51 -06:00
Vinit Shenoy eb798c641a spi/pl022: Fix range checking for bits per word
pl022 ssp controller supports word lengths from 4 to 16 (or 32) bits.
Currently implemented checks were incorrect. It has following check

if (pl022->vendor->max_bpw >= 32)

which must be checking for <=.

Also error print message is incorrect, that prints "range is from 1 to
16".

Fix both these issues.

Signed-off-by: Vinit Shenoy <vinit.shenoy@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2012-04-17 17:54:05 -06:00
Mark Brown 1e45860f54 ARM: 7366/3: amba: Remove AMBA level regulator support
The AMBA bus regulator support is being used to model on/off switches
for power domains which isn't terribly idiomatic for modern kernels with
the generic power domain code and creates integration problems on platforms
which don't use regulators for their power domains as it's hard to tell
the difference between a regulator that is needed but failed to be provided
and one that isn't supposed to be there (though DT does make that easier).

Platforms that wish to use the regulator API to manage their power domains
can indirect via the power domain interface.

This feature is only used with the vape supply of the db8500 PRCMU
driver which supplies the UARTs and MMC controllers, none of which have
support for managing vcore at runtime in mainline (only pl022 SPI
controller does).  Update that supply to have an always_on constraint
until the power domain support for the system is updated so that it is
enabled for these users, this is likely to have no impact on practical
systems as probably at least one of these devices will be active and
cause AMBA to hold the supply on anyway.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2012-04-13 14:04:08 +01:00
Linus Torvalds ef08e78268 Merge branch 'next' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine update from Vinod Koul:
 "This includes the cookie cleanup by Russell, the addition of context
  parameter for dmaengine APIs, more arm dmaengine driver cleanup by
  moving code to dmaengine, this time for imx by Javier and pl330 by
  Boojin along with the usual driver fixes."

Fix up some fairly trivial conflicts with various other cleanups.

* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (67 commits)
  dmaengine: imx: fix the build failure on x86_64
  dmaengine: i.MX: Fix merge of cookie branch.
  dmaengine: i.MX: Add support for interleaved transfers.
  dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages.
  dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'.
  dmaengine: imx-dma: remove unused arg of imxdma_sg_next.
  dmaengine: imx-dma: remove internal structure.
  dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure.
  dmaengine: imx-dma: remove 'in_use' field of 'internal' structure.
  dmaengine: imx-dma: remove sg member from internal structure.
  dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function.
  dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function.
  dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function.
  dmaengine: imx-dma: remove dma_mode member of internal structure.
  dmaengine: imx-dma: remove data member from internal structure.
  dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c
  dmaengine: at_hdmac: add slave config operation
  dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic
  dmaengine/dma_slave: introduce inline wrappers
  dma: imx-sdma: Treat firmware messages as warnings instead of erros
  ...
2012-03-29 15:34:57 -07:00
Linus Torvalds 5f0e685f31 SPI changes for v3.4.
Mostly a bunch of new drivers and driver bug fixes; but this also
 includes a few patches that create a core message queue infrastructure
 for the spi subsystem instead of making each driver open code it.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJPZ2QWAAoJEEFnBt12D9kB0LIP/2vtRDlf8wz7svU1Jc7hqkNs
 tH32KzUdHu4UJ2UzOqQC8PyeWFRbaTG26PYNKDSeuyT6ymkz2tNcAyOgzfnztPQF
 G/t25crIvN5L2940ZtBdJ24YV2wuIPnFAzGpPkFPpQKAbpXr0LLA42842++eX+Hg
 /eYkiwMjHXXN3BuoeqnMLNrdO2XaRkKbGeRW05gG/sGWKtVhbGmtlMWlNM3QhLix
 qAqUQ/tv0YqmlpZjv4t78EeqnH/Qw19F/o+Afbe50R1SEmzYDIMC1vby/eTImp5q
 8I2pJnLrk7CL1y2vQEDo+anvN+314yfCWk8FDr/ZvXf30vyzTe+gSEeeh8Z7EHHL
 w0BN8LFv6Odb5P38NS4knpUNZ7L66Va5psJhD+olERfmVaqXcnGdxS7WI8Hln8jQ
 H8pmXht7m561BN4YMBaT5n2F34BSAZqngAVVv6xfcuCWVphB/VJCpiBZ0HO0o4yP
 6T2FzoTWSRbEtht97AZmLCYdaDf0rYetrEGQSxKkiWAPnAgkCME7oR9FBqlLvRG0
 5LizCW0KX19EgjXAnJ4E1Syh2iMEZasYK6vPNG3zksMI0gzaRAzURitBN1TBxqzA
 L9LcTZO7kpuN9/ZgpDozMaNQaUO1T+Giz3IJm0GlqSMl8Xcii0St8sOiUqfdEKf5
 jKa1N0wliyDhPsT6wJlm
 =6Nsu
 -----END PGP SIGNATURE-----

Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6

Pull SPI changes for v3.4 from Grant Likely:
 "Mostly a bunch of new drivers and driver bug fixes; but this also
  includes a few patches that create a core message queue infrastructure
  for the spi subsystem instead of making each driver open code it."

* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
  spi/fsl-espi: Make sure pm is within 2..32
  spi/fsl-espi: make the clock computation easier to read
  spi: sh-hspi: modify write/read method
  spi: sh-hspi: control spi clock more correctly
  spi: sh-hspi: convert to using core message queue
  spi: s3c64xx: Fix build
  spi: s3c64xx: remove unnecessary callback msg->complete
  spi: remove redundant variable assignment
  spi: release lock on error path in spi_pump_messages()
  spi: Compatibility with direction which is used in samsung DMA operation
  spi-topcliff-pch: add recovery processing in case wait-event timeout
  spi-topcliff-pch: supports a spi mode setup and bit order setup by IO control
  spi-topcliff-pch: Fix issue for transmitting over 4KByte
  spi-topcliff-pch: Modify pci-bus number dynamically to get DMA device info
  spi/imx: simplify error handling to free gpios
  spi: Convert to DEFINE_PCI_DEVICE_TABLE
  spi: add Broadcom BCM63xx SPI controller driver
  SPI: add CSR SiRFprimaII SPI controller driver
  spi-topcliff-pch: fix -Wuninitialized warning
  spi: Mark spi_register_board_info() __devinit
  ...
2012-03-21 10:32:00 -07:00
Alexandre Bounine 16052827d9 dmaengine/dma_slave: introduce inline wrappers
Add inline wrappers for device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to hide new parameter from current users of affected interfaces.
Convert current users to use new wrappers instead of direct calls.
Suggested by Russell King [https://lkml.org/lkml/2012/2/3/269].

Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-21 19:20:22 +05:30
Linus Walleij ffbbdd2132 spi: create a message queueing infrastructure
This rips the message queue in the PL022 driver out and pushes
it into (optional) common infrastructure. Drivers that want to
use the message pumping thread will need to define the new
per-messags transfer methods and leave the deprecated transfer()
method as NULL.

Most of the design is described in the documentation changes that
are included in this patch.

Since there is a queue that need to be stopped when the system
is suspending/resuming, two new calls are implemented for the
device drivers to call in their suspend()/resume() functions:
spi_master_suspend() and spi_master_resume().

ChangeLog v1->v2:
- Remove Kconfig entry and do not make the queue support optional
  at all, instead be more agressive and have it as part of the
  compulsory infrastructure.
- If the .transfer() method is implemented, delete print a small
  deprecation notice and do not start the transfer pump.
- Fix a bitrotted comment.
ChangeLog v2->v3:
- Fix up a problematic sequence courtesy of Chris Blair.
- Stop rather than destroy the queue on suspend() courtesy of
  Chris Blair.

Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2012-03-07 19:19:48 -07:00
Viresh Kumar 258aea76f5 dmaengine: Pass dma_slave_config .device_fc = NULL for all existing users
.device_fc is added in struct dma_slave_config recently. All user drivers, which
want DMA to be the flow controller must pass this field as false. As earlier
driver don't look to use this feature, mark it false for now.

Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-02-22 18:15:37 +05:30
Russell King a5ab6291b1 Fix section mismatch in spi-pl022.c
WARNING: drivers/spi/built-in.o(.devinit.text+0xdb8): Section mismatch in reference from the function pl022_probe() to the function .init.text:pl022_dma_probe()
The function __devinit pl022_probe() references
a function __init pl022_dma_probe().
If pl022_dma_probe is only used by pl022_probe then
annotate pl022_dma_probe with a matching annotation.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2012-02-13 11:57:58 -07:00
Chris Blair 14af60b6fb spi/pl022: Add high priority message pump support
This switches the PL022 worker to a kthread in order to get
hold of a mechanism to control the message pump priority. On
low-latency systems elevating the message kthread to realtime
priority give a real sleek response curve. This has been
confirmed by measurements. Realtime priority elevation for
a certain PL022 port can be requested from platform data.

Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2012-02-02 11:32:16 -07:00
Linus Torvalds 57f2685c16 Merge branch 'next' of git://git.infradead.org/users/vkoul/slave-dma
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (53 commits)
  ARM: mach-shmobile: specify CHCLR registers on SH7372
  dma: shdma: fix runtime PM: clear channel buffers on reset
  dma/imx-sdma: save irq flags when use spin_lock in sdma_tx_submit
  dmaengine/ste_dma40: clear LNK on channel startup
  dmaengine: intel_mid_dma: remove legacy pm interface
  ASoC: mxs: correct 'direction' of device_prep_dma_cyclic
  dmaengine: intel_mid_dma: error path fix
  dmaengine: intel_mid_dma: locking and freeing fixes
  mtd: gpmi-nand: move to dma_transfer_direction
  mtd: fix compile error for gpmi-nand
  mmc: mxs-mmc: fix the dma_transfer_direction migration
  dmaengine: add DMA_TRANS_NONE to dma_transfer_direction
  dma: mxs-dma: Don't use CLKGATE bits in CTRL0 to disable DMA channels
  dma: mxs-dma: make mxs_dma_prep_slave_sg() multi user safe
  dma: mxs-dma: Always leave mxs_dma_init() with the clock disabled.
  dma: mxs-dma: fix a typo in comment
  DMA: PL330: Remove pm_runtime_xxx calls from pl330 probe/remove
  video i.MX IPU: Fix display connections
  i.MX IPU DMA: Fix wrong burstsize settings
  dmaengine/ste_dma40: allow fixed physical channel
  ...

Fix up conflicts in drivers/dma/{Kconfig,mxs-dma.c,pl330.c}

The conflicts looked pretty trivial, but I'll ask people to verify them.
2012-01-17 18:40:24 -08:00
Linus Torvalds fbce1c234f Changes queued in gpio/next for the start of the 3.3 merge window
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJPBSJSAAoJEEFnBt12D9kBDmIP/R6PWxg+NrJaGDmxRWBBkOch
 iI4Et7GT3Sk5hYqPz0kehiSz1F4bqpYK3JmdfqotJIhQCM2znXM+BaDLzgFnMsRf
 g4t70PIZQMpk3pj4gtIkMpZCkRdA9VFriIf1cEdHcLiRdNVsXlTE6CcQT4fbE1P/
 JTAGBrVDwbchuoPsf7Mbu8SYT+cQdWLKpgzC4fAzI++QoYyYBtfvuCHTE4VvasNS
 jMDOfT+u0Gwp6LW34v0gKk7MXEQzeq07r1VZxMyuaWbRQoiLr5d1fy97+Fh5+4dU
 Rb9C6zGIoBzRdiJLlfNYrls/FueDHwPyIwXuapMp5QbaGN5fkhVpIVIhYICOLdHW
 IXH2V3saK1s6QbD7nErNT2lCWZQSCUKq/PR9W40dj3PYAI0oxbRBSoPdfGuW1Bl7
 fYqClUza1Bln8bEmmsvAOnIDdfs6zpkWmfouwx4AGaHTfzIAg4VRdoxdUpS8h+/d
 sNEYi99IuYfl3KWCwQbWJMgCOvoBdOGZSCsTrXnjLf1HJCsQOt/Md69Ff6DLn1VR
 gDp0EeqgDH5oXJmQTW1WjXaJJair2j8pY8mlmGxl1AqA4aY8C3dxIfHxlBPzdxii
 I6KTPaIUSXZaOo6e7XDjjjTzabL4q0aQGT5ahpKj928Rnx00QZNXoTy4FmYkL+0k
 j7QZfM/p6+vfxekKUR17
 =9ugo
 -----END PGP SIGNATURE-----

Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6

Changes queued in gpio/next for the start of the 3.3 merge window

* tag 'gpio-for-linus-20120104' of git://git.secretlab.ca/git/linux-2.6:
  gpio: Add decode of WM8994 GPIO configuration
  gpio: Convert GPIO drivers to module_platform_driver
  gpio: Fix typo in comment in Samsung driver
  gpio: Explicitly index samsung_gpio_cfgs
  gpio: Add Linus Walleij as gpio co-maintainer
  of: Add device tree selftests
  of: create of_phandle_args to simplify return of phandle parsing data
  gpio/powerpc: Eliminate duplication of of_get_named_gpio_flags()
  gpio/microblaze: Eliminate duplication of of_get_named_gpio_flags()
  gpiolib: output basic details and consolidate gpio device drivers
  pch_gpio: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
  pch_gpio: Support new device LAPIS Semiconductor ML7831 IOH
  spi/pl022: make the chip deselect handling thread safe
  spi/pl022: add support for pm_runtime autosuspend
  spi/pl022: disable the PL022 block when unused
  spi/pl022: move device disable to workqueue thread
  spi/pl022: skip default configuration before suspending
  spi/pl022: fix build warnings
  spi/pl022: only enable RX interrupts when TX is complete
2012-01-07 12:15:36 -08:00
Linus Torvalds d3d0b02434 Merge branch 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
  sound: aaci: Enable module alias autogeneration for AMBA drivers
  watchdog: sp805: Enable module alias autogeneration for AMBA drivers
  fbdev: amba: Enable module alias autogeneration for AMBA drivers
  serial: pl011: Enable module alias autogeneration for AMBA drivers
  serial: pl010: Enable module alias autogeneration for AMBA drivers
  spi: pl022: Enable module alias autogeneration for AMBA drivers
  rtc: pl031: Enable module alias autogeneration for AMBA drivers
  rtc: pl030: Enable module alias autogeneration for AMBA drivers
  mmc: mmci: Enable module alias autogeneration for AMBA drivers
  input: ambakmi: Enable module alias autogeneration for AMBA drivers
  gpio: pl061: Enable module alias autogeneration for AMBA drivers
  dmaengine: pl330: Enable module alias autogeneration for AMBA drivers
  dmaengine: pl08x: Enable module alias autogeneration for AMBA drivers
  hwrng: nomadik: Enable module alias autogeneration for AMBA drivers
  ARM: amba: Auto-generate AMBA driver module aliases during modpost
  ARM: amba: Move definition of struct amba_id to mod_devicetable.h
2012-01-06 18:03:30 -08:00
Virupax Sadashivpetimath 8b8d719161 spi/pl022: make the chip deselect handling thread safe
There is a possibility that the pump_message and giveback
run in parallel on a SMP system. Both the pump_message and
giveback threads work on the same SPI message queue.
Results will be in correct if the pump_message gets to
work on the queue first.

when the pump_message works with the queue, it reads the
head of the queue and removes it from the queue. pump_message
activates the chip select depending on this message read.

This leads to giveback working on the modified queue or a
emptied queue. If the queue is empty or if the next message on
the queue (which is not the actual next message, as the pump
message has removed the next message from the queue) is not for
the same SPI device as that Of the previous one, giveback will
de-activate the chip select activated by pump_message(),
which is wrong.

To solve this problem pump_message is made not to run and
access the queue until the giveback is done handling the queue.
I.e. by making the cur_msg NULL after the giveback has read the
queue.

Also a state variable has been introduced to keep track of when
the CS for next message is already activated and avoid to
double-activate it.

Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-01 17:16:08 +01:00
Chris Blair 53e4acea0e spi/pl022: add support for pm_runtime autosuspend
Adds support for configuring the spi bus to use autosuspend for
runtime power management. This can reduce the latency in starting an
spi transfer by not suspending the device immediately following
completion of a transfer. If another transfer then takes place before
the autosuspend timeout, the call to resume the device can return
immediately rather than needing to risk sleeping in order to resume
the device.

Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-01 17:16:08 +01:00
Virupax Sadashivpetimath 0ad2deeab5 spi/pl022: disable the PL022 block when unused
Make sure we clear the enable bit when the block is not used.
This will save some energy in certain hardware versions.

Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-01 17:16:08 +01:00
Chris Blair d4b6af2e0e spi/pl022: move device disable to workqueue thread
Moves the disabling of the device and clocks to the same thread in
which the device and clocks are enabled. This avoids SMP issues where
the device can be enabled for a transfer by one thread and then
disabled by the completion of the previous transfer in another thread.

Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-01 17:16:08 +01:00
Virupax Sadashivpetimath 4ca9fb46d8 spi/pl022: skip default configuration before suspending
The loading of the default configuration before suspending has
been in the driver since its inception, but it is not really
needed. Especially so since we take to all the trouble of
enabling and disabling power and clock just to do this. Let's
scrap this now.

Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-01 17:16:08 +01:00
Jonas Aaberg c4a4784308 spi/pl022: fix build warnings
The driver build complains with newer compilers unless you
initialize this struct properly.

Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-01 17:16:07 +01:00
Chris Blair 172289df40 spi/pl022: only enable RX interrupts when TX is complete
For interrupt mode transfers, start with only TX interrupts enabled
to reduce the overall number of interrupts received. Once TX is
complete, enable RX interrupts to complete the transfer.

Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-01 17:16:07 +01:00
Dave Martin 7eeac71b9f spi: pl022: Enable module alias autogeneration for AMBA drivers
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
2011-11-22 10:58:32 +00:00
Vinod Koul e0d23ef29e Merge branch 'dma_slave_direction' into next_test_dirn
resolved conflicts:
	drivers/media/video/mx3_camera.c
2011-11-17 14:54:57 +05:30
Ulf Hansson 71e63e748e ARM: 7149/1: spi/pl022: Enable clock in probe
Make sure we enable the clock before leaving probe.

Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-11-08 18:25:03 +00:00
Vinod Koul a485df4b44 spi, serial: move to dma_transfer_direction
fixup usage of dma direction by introducing dma_transfer_direction,
this patch moves spi, serial drivers to use new enum

Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
2011-10-31 09:40:26 +05:30
Linus Torvalds 18c0635363 Merge branch 'spi/next' of git://git.secretlab.ca/git/linux-2.6
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6:
  drivercore: Add helper macro for platform_driver boilerplate
  spi: irq: Remove IRQF_DISABLED
  OMAP: SPI: Fix the trying to free nonexistent resource error
  spi/spi-ep93xx: add module.h include
  spi/tegra: fix compilation error in spi-tegra.c
  spi: spi-dw: fix all sparse warnings
  spi/spi-pl022: Call pl022_dma_remove(pl022) only if enable_dma is true
  spi/spi-pl022: calculate_effective_freq() must set rate <= requested rate
  spi/spi-pl022: Don't allocate more sg than required.
  spi/spi-pl022: Use GFP_ATOMIC for allocation from tasklet
  spi/spi-pl022: Resolve formatting issues
2011-10-29 07:28:36 -07:00
Russell King 7ff6bcf048 clk: spi-pl022: convert to clk_prepare()/clk_unprepare()
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-09-27 09:25:53 +01:00
Peter Hüwe 6cfa6279ed ARM: 7079/1: spi: Fix builderror in spi-pl022.c
This patch fixes a build error, introduced by commit (67fc8b9f, "PM: add
runtime PM support to core Primecell driver") which unfortunately was a little
bit incomplete and did contain a typo (11 instead of 22).
I'm not sure how this patch could have been tested back then, if it
doesn't even compile ;)

The build failure was:
drivers/spi/spi-pl022.c:2292: error: 'adev' undeclared (first use in
this function)
drivers/spi/spi-pl022.c:2344: error: 'pl022_suspend' undeclared here
(not in a function)

The build failure appears e.g. for the u8500 and realview defconfig.

Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-09-22 16:21:43 +01:00
Russell King 92b97f0aac PM: add runtime PM support to core Primecell driver
Add runtime PM support to the core Primecell driver, following the PCI
model of how this is done.

Rather than having every driver fiddle about with enabling runtime PM,
that's dealt with in the core and instead, drivers just do a put() in
their probe and a balancing get() in their remove function to activate
runtime PM for the device.

As we're dealing with enabling runtime PM in the core, fix up spi-pl022
as it must not enable and disable runtime PM itself anymore.

Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-09-22 16:21:42 +01:00
Viresh Kumar 3e3ea71627 spi/spi-pl022: Call pl022_dma_remove(pl022) only if enable_dma is true
pl022_dma_remove() should be called only if enable_dma is true. There is no
point calling it when pl022_dma_probe() is not called, which again depends on
enable_dma.

Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-09-21 09:41:48 -06:00
Viresh Kumar 0379b2a33a spi/spi-pl022: calculate_effective_freq() must set rate <= requested rate
There were few issues with calculate_effective_freq() routine:
- It was returning first rate found >= requested rate. Now, if system have spi's
  rate as 83 MHz, with possible prescaled rates as 83, 41.5, 20.75, 13.83 (as we
  can prescale with multiples of 2). If user has given rate to be programmed as
  22 MHz, then driver programmes it to 41.5 MHz. This looks to be incorrect, as
  user might have given the upper limit of the device, and we are programming it
  above it.
- Driver finds the first satisfying rate and programmes it, but with other
  values of scr & cpsdvsr, it is possible to get more closer rate.

This patch fixes these two issues, with some reformatting inside the code.  This
also creates a inline routine to calculate prescaled rate based on spi's rate,
cpsdvsr and scr.

Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-09-21 09:41:47 -06:00
Viresh Kumar b181565ee6 spi/spi-pl022: Don't allocate more sg than required.
In routine configure_dma(), if transfer->len = PAGE_SIZE, then pages is one more
than required. While leads to one more sg getting allocated.

This is wrong. Correct this to allocate correct number of sg.

Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-09-21 09:41:47 -06:00
Viresh Kumar 538a18dc18 spi/spi-pl022: Use GFP_ATOMIC for allocation from tasklet
tasklets don't allow invocation to sleeping routines. In configure_dma()
routine, sg_alloc_table() was called with GFP_KERNEL flag and so this causes
crash when called from tasklet.

Replace GFP_KERNEL with GFP_ATOMIC to get this fixed.

Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-09-21 09:41:47 -06:00
Viresh Kumar f1e45f86ed spi/spi-pl022: Resolve formatting issues
There were few formatting related issues in code. This patch fixes them.
Fixes include:
- Remove extra blank lines
- align code to 80 cols
- combine several lines to one line
- Replace multiple spaces with tabs
- Remove spaces before labels

Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-09-20 11:22:59 -06:00
Linus Walleij 50658b6602 spi/pl022: remove function cannot exit
The remove function in the PL022 driver cannot abort the remove
function any way, so restructure the code so as not to make that
assumption. Remove will now proceed no matter whether it can
stop the transfer queue or not.

Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-08-02 14:54:11 +01:00
Grant Likely f8db4cc4f2 Merge branch 'spi/merge' into spi/next 2011-06-17 08:32:26 -06:00
Linus Walleij 78b2b911bf spi/pl022: strengthen FIFO watermark level checks
The platform configuration can select custom FIFO watermarks, but
these may conflict the actual FIFO size of the PL022 variant if
set too high. So strengthen the sanity checks to deny any
conflicting settings.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-06-16 08:27:05 -06:00
Rabin Vincent bcda6ff8dd spi/pl022: support runtime PM
Insert notifiers for the runtime PM API. With this the runtime
PM layer kicks in to action where used.

Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Rebased to Linux 3.0-rc3, edit description]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-06-16 08:27:00 -06:00
Linus Walleij 083be3f053 spi/pl022: initialize burstsize from FIFO trigger level
Configure the DMA burstsize from the FIFO trigger level supplied
with the controller configuration data. This is based on a patch
from Virupax, but I rewrote it differently.

Reported-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-06-16 08:26:58 -06:00
Grant Likely ca632f5566 spi: reorganize drivers
Sort the SPI makefile and enforce the naming convention spi_*.c for
spi drivers.

This change also rolls the contents of atmel_spi.h into the .c file
since there is only one user of that particular include file.

v2: - Use 'spi-' prefix instead of 'spi_' to match what seems to be
      be the predominant pattern for subsystem prefixes.
    - Clean up filenames in Kconfig and header comment blocks

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
2011-06-06 01:16:30 -06:00