The ore need suplied a r4w_get_page/r4w_put_page API
from Filesystem so it can get cache pages to read-into when
writing parial stripes.
Also I commented out and NULLed the .writepage (singular)
vector. Because it gives terrible write pattern to raid
and is apparently not needed. Even in OOM conditions the
system copes (even better) with out it.
TODO: How to specify to write_cache_pages() to start
or include a certain page?
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Current ore_check_io API receives a residual
pointer, to report partial IO. But it is actually
not used, because in a multiple devices IO there
is never a linearity in the IO failure.
On the other hand if every failing device is reported
through a received callback measures can be taken to
handle only failed devices. One at a time.
This will also be needed by the objects-layout-driver
for it's error reporting facility.
Exofs is not currently using the new information and
keeps the old behaviour of failing the complete IO in
case of an error. (No partial completion)
TODO: Use an ore_check_io callback to set_page_error only
the failing pages. And re-dirty write pages.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
All users of the ore will need to check if current code
supports the given layout. For example RAID5/6 is not
currently supported.
So move all the checks from exofs/super.c to a new
ore_verify_layout() to be used by ore users.
Note that any new layout should be passed through the
ore_verify_layout() because the ore engine will prepare
and verify some internal members of ore_layout, and
assumes it's called.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
If at read/write_done the actual IO was shorter then requested,
reported in returned ios->length. It is not an error. The reminder
of the pages should just be unlocked but not marked uptodate or
end_page_writeback. They will be re issued later by the VFS.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Usually a single IO is confined to one group of devices
(group_width) and at the boundary of a raid group it can
spill into a second group. Current code would allocate a
full device_table size array at each io_state so it can
comply to requests that span two groups. Needless to say
that is very wasteful, specially when device_table count
can get very large (hundreds even thousands), while a
group_width is usually 8 or 10.
* Change ore API to trim on IO that spans two raid groups.
The user passes offset+length to ore_get_rw_state, the
ore might trim on that length if spanning a group boundary.
The user must check ios->length or ios->nrpages to see
how much IO will be preformed. It is the responsibility
of the user to re-issue the reminder of the IO.
* Modify exofs To copy spilled pages on to the next IO.
This means one last kick is needed after all coalescing
of pages is done.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
ore_components already has a comps member so this leads
to things like comps->comps which is annoying. the name oc
was already used in new code. So rename all old usage of
ore_components comps => ore_components oc.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
ORE stands for "Objects Raid Engine"
This patch is a mechanical rename of everything that was in ios.c
and its API declaration to an ore.c and an osd_ore.h header. The ore
engine will later be used by the pnfs objects layout driver.
* File ios.c => ore.c
* Declaration of types and API are moved from exofs.h to a new
osd_ore.h
* All used types are prefixed by ore_ from their exofs_ name.
* Shift includes from exofs.h to osd_ore.h so osd_ore.h is
independent, include it from exofs.h.
Other than a pure rename there are no other changes. Next patch
will move the ore into it's own module and will export the API
to be used by exofs and later the layout driver
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Exofs raid engine was saving on memory space by having a single layout-info,
single pid, and a single device-table, global to the filesystem. Then passing
a credential and object_id info at the io_state level, private for each
inode. It would also devise this contraption of rotating the device table
view for each inode->ino to spread out the device usage.
This is not compatible with the pnfs-objects standard, demanding that
each inode can have it's own layout-info, device-table, and each object
component it's own pid, oid and creds.
So: Bring exofs raid engine to be usable for generic pnfs-objects use by:
* Define an exofs_comp structure that holds obj_id and credential info.
* Break up exofs_layout struct to an exofs_components structure that holds a
possible array of exofs_comp and the array of devices + the size of the
arrays.
* Add a "comps" parameter to get_io_state() that specifies the ids creds
and device array to use for each IO.
This enables to keep the layout global, but the device-table view, creds
and IDs at the inode level. It only adds two 64bit to each inode, since
some of these members already existed in another form.
* ios raid engine now access layout-info and comps-info through the passed
pointers. Everything is pre-prepared by caller for generic access of
these structures and arrays.
At the exofs Level:
* Super block holds an exofs_components struct that holds the device
array, previously in layout. The devices there are in device-table
order. The device-array is twice bigger and repeats the device-table
twice so now each inode's device array can point to a random device
and have a round-robin view of the table, making it compatible to
previous exofs versions.
* Each inode has an exofs_components struct that is initialized at
load time, with it's own view of the device table IDs and creds.
When doing IO this gets passed to the io_state together with the
layout.
While preforming this change. Bugs where found where credentials with the
wrong IDs where used to access the different SB objects (super.c). As well
as some dead code. It was never noticed because the target we use does not
check the credentials.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
ios.c will be moving to an external library, for use by the
objects-layout-driver. Remove from it some exofs specific functions.
Also g_attr_logical_length is used both by inode.c and ios.c
move definition to the later, to keep it independent
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
In future raid code we will need to know the IO offset/length
and if it's a read or write to determine some of the array
sizes we'll need.
So add a new exofs_get_rw_state() API for use when
writeing/reading. All other simple cases are left using the
old way.
The major change to this is that now we need to call
exofs_get_io_state later at inode.c::read_exec and
inode.c::write_exec when we actually know these things. So this
patch is kept separate so I can test things apart from other
changes.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
* 'for-2.6.39/core' of git://git.kernel.dk/linux-2.6-block: (65 commits)
Documentation/iostats.txt: bit-size reference etc.
cfq-iosched: removing unnecessary think time checking
cfq-iosched: Don't clear queue stats when preempt.
blk-throttle: Reset group slice when limits are changed
blk-cgroup: Only give unaccounted_time under debug
cfq-iosched: Don't set active queue in preempt
block: fix non-atomic access to genhd inflight structures
block: attempt to merge with existing requests on plug flush
block: NULL dereference on error path in __blkdev_get()
cfq-iosched: Don't update group weights when on service tree
fs: assign sb->s_bdi to default_backing_dev_info if the bdi is going away
block: Require subsystems to explicitly allocate bio_set integrity mempool
jbd2: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
jbd: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
fs: make fsync_buffers_list() plug
mm: make generic_writepages() use plugging
blk-cgroup: Add unaccounted time to timeslice_used.
block: fixup plugging stubs for !CONFIG_BLOCK
block: remove obsolete comments for blkdev_issue_zeroout.
blktrace: Use rq->cmd_flags directly in blk_add_trace_rq.
...
Fix up conflicts in fs/{aio.c,super.c}
Before when creating a new inode, we'd set the sb->s_dirt flag,
and sometime later the system would write out s_nextid as part
of the sb_info. Also on inode sync we would force the sb sync
as well.
Define the s_nextid as a new partition attribute and set it
every time we create a new object.
At mount we read it from it's new place.
We now never set sb->s_dirt anywhere in exofs. write_super
is actually never called. The call to exofs_write_super from
exofs_put_super is also removed because the VFS always calls
->sync_fs before calling ->put_super twice.
To stay backward-and-forward compatible we also write the old
s_nextid in the super_block object at unmount, and support zero
length attribute on mount.
This also fixes a BUG where in layouts when group_width was not
a divisor of EXOFS_SUPER_ID (0x10000) the s_nextid was not read
from the device it was written to. Because of the sliding window
layout trick, and because the read was always done from the 0
device but the write was done via the raid engine that might slide
the device view. Now we read and write through the raid engine.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
* Set all inode->i_mapping->backing_dev_info to point to
the per super-block sb->s_bdi.
* Calculating a read_ahead that is:
- preferable 2 stripes long
(Future patch will add a mount option to override this)
- Minimum 128K aligned up to stripe-size
- Caped to maximum-IO-sizes round down to stripe_size.
(Max sizes are governed by max bio-size that fits in a page
times number-of-devices)
CC: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
It is incorrect to test inode dirty bits without participating in the inode
writeback protocol. Inode writeback sets I_SYNC and clears I_DIRTY_?, then
writes out the particular bits, then clears I_SYNC when it is done. BTW. it
may not completely write all pages out, so I_DIRTY_PAGES would get set
again.
This is a standard pattern used throughout the kernel's writeback caches
(I_SYNC ~= I_WRITEBACK, if that makes it clearer).
And so it is not possible to determine an inode's dirty status just by
checking I_DIRTY bits. Especially not for the purpose of data integrity
syncs.
Missing the check for these bits means that fsync can complete while
writeback to the inode is underway. Inode writeback functions get this
right, so call into them rather than try to shortcut things by testing
dirty state improperly.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This reverts commit 115e19c535.
Apparently setting inode->bdi to one's own sb->s_bdi stops VFS from
sending *read-aheads*. This problem was bisected to this commit. A
revert fixes it. I'll investigate farther why is this happening for the
next Kernel, but for now a revert.
I'm sending to stable@kernel.org as well, since it exists also in
2.6.37. 2.6.36 is good and does not have this patch.
CC: Stable Tree <stable@kernel.org>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
exofs_new_inode() was incrementing the inode->i_count and
decrementing it in create_done(), in a bad attempt to make sure
the inode will still be there when the asynchronous create_done()
finally arrives. This was very stupid because iput() was not called,
and if it was actually needed, it would leak the inode.
However all this is not needed, because at exofs_evict_inode()
we already wait for create_done() by waiting for the
object_created event. Therefore remove the superfluous ref counting
and just Thicken the comment at exofs_evict_inode() a bit.
While at it change places that open coded wait_obj_created()
to call the already available wrapper.
CC: Dave Chinner <dchinner@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Though it has been promised that inode->i_mapping->backing_dev_info
is not used and the supporting code is fine. Until the pointer
will default to NULL, I'd rather it points to the correct thing
regardless.
At least for future infrastructure coder it is a clear indication
of where are the key points that inodes are initialized.
I know because it took me time to find this out.
Signed-off-by: Boaz Harrosh <Boaz Harrosh bharrosh@panasas.com>
Last BUG fix added a flag to the the page_collect structure
to communicate with readpage_strip. This calls for a clean up
removing that flag's reincarnations in the read functions
parameters.
Signed-off-by: Boaz Harrosh <Boaz Harrosh bharrosh@panasas.com>
This BUG is there since the first submit of the code, but only triggered
in last Kernel. It's timing related do to the asynchronous object-creation
behaviour of exofs. (Which should be investigated farther)
The bug is obvious hence the fixed.
Signed-off-by: Boaz Harrosh <Boaz Harrosh bharrosh@panasas.com>
* 'for-linus' of git://git.open-osd.org/linux-open-osd:
exofs: Fix groups code when num_devices is not divisible by group_width
exofs: Remove useless optimization
exofs: exofs_file_fsync and exofs_file_flush correctness
exofs: Remove superfluous dependency on buffer_head and writeback
These changes are crafted based on the similar
conversion done to ext2 by Nick Piggin.
* Remove the deprecated ->truncate vector. Let exofs_setattr
take care of on-disk size updates.
* Call truncate_pagecache on the unused pages if
write_begin/end fails.
* Cleanup exofs_delete_inode that did stupid inode
writes and updates on an inode that will be
removed.
* And finally get rid of exofs_get_block. We never
had any blocks it was all for calling nobh_truncate_page.
nobh_truncate_page is not actually needed in exofs since
the last page is complete and gone, just like all the other
pages. There is no partial blocks in exofs.
I've tested with this patch, and there are no apparent
failures, so far.
CC: Nick Piggin <npiggin@suse.de>
CC: Christoph Hellwig <hch@lst.de>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Replace inode_setattr with opencoded variants of it in all callers. This
moves the remaining call to vmtruncate into the filesystem methods where it
can be replaced with the proper truncate sequence.
In a few cases it was obvious that we would never end up calling vmtruncate
so it was left out in the opencoded variant:
spufs: explicitly checks for ATTR_SIZE earlier
btrfs,hugetlbfs,logfs,dlmfs: explicitly clears ATTR_SIZE earlier
ufs: contains an opencoded simple_seattr + truncate that sets the filesize just above
In addition to that ncpfs called inode_setattr with handcrafted iattrs,
which allowed to trim down the opencoded variant.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
exofs_releasepage && exofs_invalidatepage are never called.
Leave the WARN_ONs but remove any code. Remove the
cleanup other stale #includes.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
* 'for-linus' of git://git.open-osd.org/linux-open-osd:
exofs: confusion between kmap() and kmap_atomic() api
exofs: Add default address_space_operations
All vectors of address_space_operations should be initialized
by the filesystem. Add the missing parts.
This is actually an optimization, by using
__set_page_dirty_nobuffers. The default, in case of NULL,
would be __set_page_dirty_buffers which has these extar if(s).
.releasepage && .invalidatepage should both not be called
because page_private() is NULL in exofs. Put a WARN_ON if
they are called, to indicate the Kernel has changed in this
regard, if when it does.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This gives the filesystem more information about the writeback that
is happening. Trond requested this for the NFS unstable write handling,
and other filesystems might benefit from this too by beeing able to
distinguish between the different callers in more detail.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If an object is referenced by a directory but does not
exist on a target, it is a very serious corruption that
means:
1. Either a power failure with very slim chance of it
happening. Because the directory update is always submitted
much after object creation, but if a directory is written
to one device and the object creation to another it might
theoretically happen.
2. It only ever happened to me while developing with BUGs
causing file corruption. Crashes could also cause it but
they are more like case 1.
In any way the object does not exist, so data is surely lost.
If there is a mix-up in the obj-id or data-map, then lost objects
can be salvaged by off-line fsck. The only recoverable information
is the directory name. By letting it appear as a regular empty file,
with date==0 (1970 Jan 1st) ownership to root, we enable recovery
of the only useful information. And also enable deletion or over-write.
I can see how this can hurt.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
* inode.c operations are full-pages based, and not actually
true scatter-gather
* Lets us use more pages at once upto 512 (from 249) in 64 bit
* Brings us much much closer to be able to use exofs's io_state engine
from objlayout driver. (Once I decide where to put the common code)
After RAID0 patch the outer (input) bio was never used as a bio, but
was simply a page carrier into the raid engine. Even in the simple
mirror/single-dev arrangement pages info was copied into a second bio.
It is now easer to just pass a pages array into the io_state and prepare
bio(s) once.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
We now support striping over mirror devices. Including variable sized
stripe_unit.
Some limits:
* stripe_unit must be a multiple of PAGE_SIZE
* stripe_unit * stripe_count is maximum upto 32-bit (4Gb)
Tested RAID0 over mirrors, RAID0 only, mirrors only. All check.
Design notes:
* I'm not using a vectored raid-engine mechanism yet. Following the
pnfs-objects-layout data-map structure, "Mirror" is just a private
case of "group_width" == 1, and RAID0 is a private case of
"Mirrors" == 1. The performance lose of the general case over the
particular special case optimization is totally negligible, also
considering the extra code size.
* In general I added a prepare_stripes() stage that divides the
to-be-io pages to the participating devices, the previous
exofs_ios_write/read, now becomes _write/read_mirrors and a new
write/read upper layer loops on all devices calling
_write/read_mirrors. Effectively the prepare_stripes stage is the all
secret.
Also truncate need fixing to accommodate for striping.
* In a RAID0 arrangement, in a regular usage scenario, if all inode
layouts will start at the same device, the small files fill up the
first device and the later devices stay empty, the farther the device
the emptier it is.
To fix that, each inode will start at a different stripe_unit,
according to it's obj_id modulus number-of-stripe-units. And
will then span all stripe-units in the same incrementing order
wrapping back to the beginning of the device table. We call it
a stripe-units moving window.
Special consideration was taken to keep all devices in a mirror
arrangement identical. So a broken osd-device could just be cloned
from one of the mirrors and no FS scrubbing is needed. (We do that
by rotating stripe-unit at a time and not a single device at a time.)
TODO:
We no longer verify object_length == inode->i_size in exofs_iget.
(since i_size is stripped on multiple objects now).
I should introduce a multiple-device attribute reading, and use
it in exofs_iget.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
* Layouts describe the way a file is spread on multiple devices.
The layout information is stored in the objects attribute introduced
in this patch.
* There can be multiple generating function for the layout.
Currently defined:
- No attribute present - use below moving-window on global
device table, all devices.
(This is the only one currently used in exofs)
- an obj_id generated moving window - the obj_id is a randomizing
factor in the otherwise global map layout.
- An explicit layout stored, including a data_map and a device
index list.
- More might be defined in future ...
* There are two attributes defined of the same structure:
A-data-files-layout - This layout is used by data-files. If present
at a directory, all files of that directory will
be created with this layout.
A-meta-data-layout - This layout is used by a directory and other
meta-data information. Also inherited at creation
of subdirectories.
* At creation time inodes are created with the layout specified above.
A usermode utility may change the creation layout on a give directory
or file. Which in the case of directories, will also apply to newly
created files/subdirectories, children of that directory.
In the simple unaltered case of a newly created exofs, no layout
attributes are present, and all layouts adhere to the layout specified
at the device-table.
* In case of a future file system loaded in an old exofs-driver.
At iget(), the generating_function is inspected and if not supported
will return an IO error to the application and the inode will not
be loaded. So not to damage any data.
Note: After this patch we do not yet support any type of layout
only the RAID0 patch that enables striping at the super-block
level will add support for RAID0 layouts above. This way we
are past and future compatible and fully bisectable.
* Access to the device table is done by an accessor since
it will change according to above information.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
* Abstract away those members in exofs_sb_info that are related/needed
by a layout into a new exofs_layout structure. Embed it in exofs_sb_info.
* At exofs_io_state receive/keep a pointer to an exofs_layout. No need for
an exofs_sb_info pointer, all we need is at exofs_layout.
* Change any usage of above exofs_sb_info members to their new name.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
* Last debug trimming left in some stupid print, remove them.
Fixup some other prints
* Shift printing from inode.c to ios.c
* Add couple of prints when memory allocation fails.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
exofs uses simple_write_end() for it's .write_end handler. But
it is not enough because simple_write_end() does not call
mark_inode_dirty() when it extends i_size. So even if we do
call mark_inode_dirty at beginning of write out, with a very
long IO and a saturated system we might get the .write_inode()
called while still extend-writing to file and miss out on the last
i_size updates.
So override .write_end, call simple_write_end(), and afterwords if
i_size was changed call mark_inode_dirty().
It stands to logic that since simple_write_end() was the one extending
i_size it should also call mark_inode_dirty(). But it looks like all
users of simple_write_end() are memory-bound pseudo filesystems, who
could careless about mark_inode_dirty(). I might submit a
warning-comment patch to simple_write_end() in future.
CC: Stable <stable@kernel.org>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
This patch changes on-disk format, it is accompanied with a parallel
patch to mkfs.exofs that enables multi-device capabilities.
After this patch, old exofs will refuse to mount a new formatted FS and
new exofs will refuse an old format. This is done by moving the magic
field offset inside the FSCB. A new FSCB *version* field was added. In
the future, exofs will refuse to mount unmatched FSCB version. To
up-grade or down-grade an exofs one must use mkfs.exofs --upgrade option
before mounting.
Introduced, a new object that contains a *device-table*. This object
contains the default *data-map* and a linear array of devices
information, which identifies the devices used in the filesystem. This
object is only written to offline by mkfs.exofs. This is why it is kept
separate from the FSCB, since the later is written to while mounted.
Same partition number, same object number is used on all devices only
the device varies.
* define the new format, then load the device table on mount time make
sure every thing is supported.
* Change I/O engine to now support Mirror IO, .i.e write same data
to multiple devices, read from a random device to spread the
read-load from multiple clients (TODO: stripe read)
Implementation notes:
A few points introduced in previous patch should be mentioned here:
* Special care was made so absolutlly all operation that have any chance
of failing are done before any osd-request is executed. This is to
minimize the need for a data consistency recovery, to only real IO
errors.
* Each IO state has a kref. It starts at 1, any osd-request executed
will increment the kref, finally when all are executed the first ref
is dropped. At IO-done, each request completion decrements the kref,
the last one to return executes the internal _last_io() routine.
_last_io() will call the registered io_state_done. On sync mode a
caller does not supply a done method, indicating a synchronous
request, the caller is put to sleep and a special io_state_done is
registered that will awaken the caller. Though also in sync mode all
operations are executed in parallel.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
In anticipation for multi-device operations, we separate osd operations
into an abstract I/O API. Currently only one device is used but later
when adding more devices, we will drive all devices in parallel according
to a "data_map" that describes how data is arranged on multiple devices.
The file system level operates, like before, as if there is one object
(inode-number) and an i_size. The io engine will split this to the same
object-number but on multiple device.
At first we introduce Mirror (raid 1) layout. But at the final outcome
we intend to fully implement the pNFS-Objects data-map, including
raid 0,4,5,6 over mirrored devices, over multiple device-groups. And
more. See: http://tools.ietf.org/html/draft-ietf-nfsv4-pnfs-obj-12
* Define an io_state based API for accessing osd storage devices
in an abstract way.
Usage:
First a caller allocates an io state with:
exofs_get_io_state(struct exofs_sb_info *sbi,
struct exofs_io_state** ios);
Then calles one of:
exofs_sbi_create(struct exofs_io_state *ios);
exofs_sbi_remove(struct exofs_io_state *ios);
exofs_sbi_write(struct exofs_io_state *ios);
exofs_sbi_read(struct exofs_io_state *ios);
exofs_oi_truncate(struct exofs_i_info *oi, u64 new_len);
And when done
exofs_put_io_state(struct exofs_io_state *ios);
* Convert all source files to use this new API
* Convert from bio_alloc to bio_kmalloc
* In io engine we make use of the now fixed osd_req_decode_sense
There are no functional changes or on disk additions after this patch.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
There are two places that initialize inodes: exofs_iget() and
exofs_new_inode()
As more members of exofs_i_info that need initialization are
added this code will grow. (soon)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Iner-loops printing is converted to EXOFS_DBG2 which is #defined
to nothing.
It is now almost bareable to just leave debug-on. Every operation
is printed once, with most relevant info (I hope).
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Boaz,
Congrats on getting all the OSD stuff into 2.6.30!
I just pulled the git, and saw that the IBM copyrights are still there.
Please remove them from all files:
* Copyright (C) 2005, 2006
* International Business Machines
IBM has revoked all rights on the code - they gave it to me.
Thanks!
Avishay
Signed-off-by: Avishay Traeger <avishay@gmail.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
When failing a read request in the sync path, called from
write_begin, I forgot to free the allocated bio, fix it.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
libosd users that need to work with bios, must sometime use
the request_queue associated with the osd_dev. Make a wrapper for
that, and convert all in-tree users.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For supporting of chained-bios we can not inspect the first
bio only, as before. Caller shall pass the total length of the
request, ie. sum_bytes(bio-chain).
Also since the bio might be a chain we don't set it's direction
on behalf of it's callers. The bio direction should be properly
set prior to this call. So fix a couple of write users that now
need to set the bio direction properly
[In this patch I change both library code and user sites at
exofs, to make it easy on integration. It should be submitted
via James's scsi-misc tree.]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
CC: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch ties all operation vectors into a file system superblock
and registers the exofs file_system_type at module's load time.
* The file system control block (AKA on-disk superblock) resides in
an object with a special ID (defined in common.h).
Information included in the file system control block is used to
fill the in-memory superblock structure at mount time. This object
is created before the file system is used by mkexofs.c It contains
information such as:
- The file system's magic number
- The next inode number to be allocated
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
implementation of directory and inode operations.
* A directory is treated as a file, and essentially contains a list
of <file name, inode #> pairs for files that are found in that
directory. The object IDs correspond to the files' inode numbers
and are allocated using a 64bit incrementing global counter.
* Each file's control block (AKA on-disk inode) is stored in its
object's attributes. This applies to both regular files and other
types (directories, device files, symlinks, etc.).
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
