The BPCSHIFT based macros, btoc*, ctob*, offtoc* and ctooff are either not
used or don't need to be used. The NDPP, NDPP, NBBY macros don't need to
be used but instead are replaced directly by PAGE_SIZE and PAGE_CACHE_SIZE
where appropriate. Initial patch and motivation from Nicolas Kaiser.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:30096a
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
We need xfs_bulkstat() to report inode stat for inodes with link count
zero but reference count non zero.
The fix here:
http://oss.sgi.com/archives/xfs/2007-09/msg00266.html
changed this behavior and made xfs_bulkstat() to filter all unlinked
inodes including those that are not destroyed yet but held by reference.
The attached patch returns back to the original behavior by marking the
on-disk inode buffer "dirty" when di_mode is cleared (at that time both
inode link and reference counter are zero).
SGI-PV: 972004
SGI-Modid: xfs-linux-melb:xfs-kern:29914a
Signed-off-by: Vlad Apostolov <vapo@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
- sanity check for NULL user buffer in xfs_ioc_bulkstat[_compat]()
- remove the special case for XFS_IOC_FSBULKSTAT with count == 1. This
special case causes bulkstat to fail because the special case uses
xfs_bulkstat_single() instead of xfs_bulkstat() and the two functions
have different semantics. xfs_bulkstat() will return the next inode
after the one supplied while skipping internal inodes (ie quota inodes).
xfs_bulkstate_single() will only lookup the inode supplied and return
an error if it is an internal inode.
- in xfs_bulkstat(), need to initialise 'lastino' to the inode supplied
so in cases were we return without examining any inodes the scan wont
restart back at zero.
- sanity check for valid *ubcountp values. Cannot sanity check for valid
ubuffer here because some users of xfs_bulkstat() don't supply a buffer.
- checks against 'ubleft' (the space left in the user's buffer) should be
against 'statstruct_size' which is the supplied minimum object size.
The mixture of checks against statstruct_size and 0 was one of the
reasons we were skipping inodes.
- if the formatter function returns BULKSTAT_RV_NOTHING and an error and
the error is not ENOENT or EINVAL then we need to abort the scan. ENOENT
is for inodes that are no longer valid and we just skip them. EINVAL is
returned if we try to lookup an internal inode so we skip them too. For
a DMF scan if the inode and DMF attribute cannot fit into the space left
in the user's buffer it would return ERANGE. We didn't handle this error
and skipped the inode. We would continue to skip inodes until one fitted
into the user's buffer or we completed the scan.
- put back the recalculation of agino (that got removed with the last fix)
at the end of the while loop. This is because the code at the start of
the loop expects agino to be the last inode examined if it is non-zero.
- if we found some inodes but then encountered an error, return success
this time and the error next time. If the formatter aborted with ENOMEM
we will now return this error but only if we couldn't read any inodes.
Previously if we encountered ENOMEM without reading any inodes we
returned a zero count and no error which falsely indicated the scan was
complete.
SGI-PV: 973431
SGI-Modid: xfs-linux-melb:xfs-kern:30089a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Here 'agino' increments through the inodes in an allocation group. At the
end of the innermost 'for' loop it will hold the value of the next inode
to look at (ie the first inode in the next cluster/chunk). Assigning
'lastino' to 'agino' resets it to the last inode in the last inode cluster
we just looked at. This causes us to look up the very same cluster and
examine all the inodes all over again, and again, and again...
We also want to set 'lastino' for the cases when we're not interested in
the inode so that the next call to bulkstat won't re-examine the same
uninteresting inodes.
SGI-PV: 971064
SGI-Modid: xfs-linux-melb:xfs-kern:29840a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
In the following scenario xfs_bulkstat() returns incorrect stale inode
state:
1. File_A is created and its inode synced to disk. 2. File_A is unlinked
and doesn't exist anymore. 3. Filesystem sync is invoked. 4. File_B is
created. File_B happens to reclaim File_A's inode. 5. xfs_bulkstat() is
called and detects File_B but reports the
incorrect File_A inode state.
Explanation for the incorrect inode state is that inodes are not
immediately synced on file create for performance reasons. This leaves the
on-disk inode buffer uninitialized (or with old state from a previous
generation inode) and this is what xfs_bulkstat() would report.
The patch marks the on-disk inode buffer "dirty" on unlink. When the inode
is reclaimed (by a new file create), xfs_bulkstat() would filter this
inode by the "dirty" mark. Once the inode is flushed to disk, the on-disk
buffer "dirty" mark is automatically removed and a following
xfs_bulkstat() would return the correct inode state.
Marking the on-disk inode buffer "dirty" on unlink is achieved by setting
the on-disk di_nlink field to 0. Note that the in-core di_nlink has
already been set to 0 and a corresponding transaction logged by
xfs_droplink(). This is an exception from the rule that any on-disk inode
buffer changes has to be followed by a disk write (inode flush).
Synchronizing the in-core to on-disk di_nlink values in advance (before
the actual inode flush to disk) should be fine in this case because the
inode is already unlinked and it would never change its di_nlink again for
this inode generation.
SGI-PV: 970842
SGI-Modid: xfs-linux-melb:xfs-kern:29757a
Signed-off-by: Vlad Apostolov <vapo@sgi.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Mark Goodwin <markgw@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Biggest bit is duplicating the dinode structure so we have one annotated for
native endianess and one for disk endianess. The other significant change
is that xfs_xlate_dinode_core is split into one helper per direction to
allow for proper annotations, everything else is trivial.
As a sidenode splitting out the incore dinode means we can move it into
xfs_inode.h in a later patch and severely improving on the include hell in
xfs.
SGI-PV: 968563
SGI-Modid: xfs-linux-melb:xfs-kern:29476a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
* 32bit struct xfs_fsop_bulkreq has different size and layout of
members, no matter the alignment. Move the code out of the #else
branch (why was it there in the first place?). Define _32 variants of
the ioctl constants.
* 32bit struct xfs_bstat is different because of time_t and on
i386 because of different padding. Make xfs_bulkstat_one() accept a
custom "output formatter" in the private_data argument which takes care
of the xfs_bulkstat_one_compat() that takes care of the different
layout in the compat case.
* i386 struct xfs_inogrp has different padding.
Add a similar "output formatter" mecanism to xfs_inumbers().
SGI-PV: 967354
SGI-Modid: xfs-linux-melb:xfs-kern:29102a
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
The previous attempts to fix the linux inode use-after-free in xfs_iunpin
simply made the problem harder to hit. We actually need complete exclusion
between xfs_reclaim and xfs_iunpin, as well as ensuring that the i_flags
are consistent during both of these functions. Introduce a new spinlock
for exclusion and the i_flags, and fix up xfs_iunpin to use igrab before
marking the inode dirty.
SGI-PV: 952967
SGI-Modid: xfs-linux-melb:xfs-kern:26964a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
list, to increase our potential readahead window and in turn improve
bulkstat performance.
SGI-PV: 944409
SGI-Modid: xfs-linux-melb:xfs-kern:26607a
Signed-off-by: Nathan Scott <nathans@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
batches of inode cluster buffers at once, before any blocking reads are
issued.
SGI-PV: 944409
SGI-Modid: xfs-linux-melb:xfs-kern:26606a
Signed-off-by: Nathan Scott <nathans@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
extract inline attributes out of the bulkstat buffer (for that case),
rather than using an (extremely expensive for large icount filesystems)
iget for fetching attrs.
SGI-PV: 944409
SGI-Modid: xfs-linux-melb:xfs-kern:26602a
Signed-off-by: Nathan Scott <nathans@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
updates and only sync back to the xfs inode when nessecary
SGI-PV: 946679
SGI-Modid: xfs-linux-melb:xfs-kern:203362a
Signed-off-by: Christoph Hellwig <hch@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!