It exceeded 80 characters. Split it into two lines.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes multiple locations where a little endian host is assumed during
ser/des of messages sent to/received from the chip.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for dropping gratuitous ARP frames which is
requirement for WFA Hotspot2.0.
Hotspot2.0 capability is enabled in driver if extended capabilities
IE from BSS descriptor has 11u interworking enabled.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
EXT_CAPAB_IE format involves IEEE header followed by bytestream of
capabilities. Current structure has incorrect member u8 for data;
fix it by defining it as u8[0].
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have usb_deregister() call in our rmmod routine. deauth,
shutdown etc. commands will be sent to FW later when bus
driver calls disconnect handler.
This mechanism works fine with SDIO and PCIe interfaces, but
there is an issue with USB.
USB bus driver returns all URBs submitted for receiving data
and command response immediately after usb_deregister() with
failure status. Hence we don't send deauth, shutdown etc.
command to firmware.
The problem is fixed by moving code from disconnect handler to
rmmod routine for USB interface.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add flags intended to report various auxiliary information
and introduce the NL80211_RXMGMT_FLAG_ANSWERED flag to report
that the frame was already answered by the device.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[REPLIED->ANSWERED, reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bug 60747 - 1286:2044 [Microsoft Surface Pro]
Marvell 88W8797 wifi show 3 interface under network
https://bugzilla.kernel.org/show_bug.cgi?id=60747
This issue was also reported previously by OLPC and some folks from
the community.
There are 3 network interfaces with different types being created
when mwifiex driver is loaded:
1. mlan0 (infra. STA)
2. uap0 (AP)
3. p2p0 (P2P_CLIENT)
The Network Manager attempts to use all 3 interfaces above without
filtering the managed interface type. As the result, 3 identical
interfaces are displayed under network manager. If user happens to
click on an entry under which its interface is uap0 or p2p0, the
association will fail.
Work around it by removing the creation of AP and P2P interfaces
at driver loading time. These interfaces can be added with 'iw' or
other applications manually when they are needed.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
config: make ARCH=m68k allmodconfig
All error/warnings:
drivers/net/wireless/mwifiex/cfg80211.c: In function
'mwifiex_fill_coalesce_rule_info':
>> drivers/net/wireless/mwifiex/cfg80211.c:2493:3: error: implicit
declaration of function 'mwifiex_is_pattern_supported'
[-Werror=implicit-function-declaration]
drivers/net/wireless/mwifiex/cfg80211.c: At top level:
drivers/net/wireless/mwifiex/cfg80211.c:2537:12: warning:
'mwifiex_cfg80211_set_coalesce' defined but not used
[-Wunused-function]
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Coalesce filters are configured in firmware based on settings
received from cfg80211.
Packet type which is required by firmware is determined based on
provided patterns in a rule:
Unicast: if pattern '01' with offset 0 is found
Multicast: if pattern '33:33' or '01:00:5e' with offset 0 is found
Broadcast: if pattern 'ff:ff:ff:ff' with offset 0 is found
Some example coalesce configuration files:
1) Coalesce Rx data packets from 192.168.0.88
mac address of our device is 00:50:43:21:53:7A
Source IP address offset comes out as 52 after following
calculations:
32 bytes of HW 802.11 header + 8 bytes LLC +
12 bytes in IPV4 header till source IP address
Destination mac is at offset 6 in HW header.
delay=100
condition=1
patterns=01,6+00:50:43:22,10+53:7A,52+c0:a8:00:58
2) Coalesce all broadcast and multicast packets(Multiple packet
types are not allowed in a single rule. Hence created separate
rules)
delay=400
condition=1
patterns=33:33
delay=400
condition=1
patterns=ff:ff:ff:ff
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The offset number is increased to accomodate requests from
user to match more fields in a Rx packet.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is modified so that it can be reused for coalesce feature.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Their names were generic. We need to define similar macros
for coalesce feature. Hence they are renamed here.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever available, use cfg80211_scan_request to populates rates
in outgoing probe request. This will help to advertise band specific
rates and fix an issue where 11b rates were advertised in probe
request going out on 11a band.
This will also ensure that we do not advertise 11b rates while P2P
scan is going on.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It has introduced by recent commit 6b41f941d7cd: "mwifiex:
handle driver initialization error paths" which adds error
path handling for mwifiex_fw_dpc().
release_firmware(adapter->*) is called for success as well
as failure paths. In failure paths, adapter is already freed
at this point.
The issue is fixed by moving mwifiex_free_adapter() call.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We missed bss_mode check for P2P client.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an issue wherein adhoc rates were being copied
into association request from P2P client.
Cc: <stable@vger.kernel.org> # 3.10.y
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an issue wherein association would fail on P2P
interfaces. This happened because we are checking priv->mode
against NL80211_IFTYPE_STATION. While this check is correct for
infrastructure stations, it would fail P2P clients for which mode
is NL80211_IFTYPE_P2P_CLIENT.
Better check would be bss_role which has only 2 values: STA/AP.
Cc: <stable@vger.kernel.org> # 3.10.y
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both type and pkt_len variables are in host endian and these should be in
Little Endian in the payload.
Signed-off-by: Tomasz Moń <desowin@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some function definitions are moved to appropriate place
to avoid forward declarations.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex_fw_dpc() asynchronously takes care of firmware download
and initialization. Currently the error paths in mwifiex_fw_dpc()
are not handled. So if wrong firmware is downloaded, required
cleanup work is not performed. memory is leaked and workqueue
remains unterminated in this case.
mwifiex_terminate_workqueue() is moved to avoid forward
declaration.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We support maximum simultaneous 2 non-AP station interfaces and
they can assume role of Station/P2P client/P2P GO.
Advertise this support to cfg80211 so that concurrent P2P/STA
operation is possible.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We already have 'struct mwifiex_ie_types_header' with same
definition. Hence host_cmd_tlv is removed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For PCIe cards, when wrong firmware is downloaded, firmware is
failed to be ready in 10 seconds. We should return an error at
this point. But currently we are sending first command to firmware.
As expected firmware doesn't respond to this command and command
timeout occurs.
This patch fixes the problem by removing unnecessary 'ret'
variable modifications in "if (ret) {" block.
The block is just supposed to update "adapter->winner" flag.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is observed that when wrong firmware is downloaded for
PCIe card, system hangs for 10 seconds. The reason is mdelay()
is used when firmware status is polled.
Replace mdelay with msleep(non-blocking API) to fix the issue.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After downloading the firmware, firmware status is checked by
reading a register. Polling interval is 100 msecs. Therefore 100
retries means the status is checked for 10 secs which is more than
sufficient for firmware to get ready.
This patch removes 1000 retries macro usage, because 100secs
time is not practical.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clear the data pointer stored in USB interface structure in
this handler. This helps to return from mwifiex_usb_disconnect()
if driver deinitialization is already performed while handling
an error path for mwifiex_usb_probe().
USB8797 card gets enumerated twice. First enumeration is for
firmware download and second enumeration expects firmware
initialization. mwifiex_usb_probe() always takes care of
deinitialization for first enumeration after firmware download.
Also, this change matches our handling for SDIO and PCIe
interfaces.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As if_ops.init_if() is called in mwifiex_register(),
corresponding cleanup routine should be called in
mwifiex_unregister().
Currently it's there in mwifiex_adapter_cleanup(), hence
interface specific cleanup is not performed if driver
initialization is failed.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is already there in mwifiex_unregister(). So unnecessary
call in mwifiex_adapter_cleanup() is removed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently it is in mwifiex_adapter_cleanup() which doesn't get
called if driver initialization is failed causing memory leak.
scan_delay_timer is initialized in mwifiex_register(), so it
should be deleted in mwifiex_unregister(). Hence it has been
moved to appropriate place.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If reboot command is issued when device is in connected state,
system hangs while booting. This issue is fixed by doing cleanup
in shutdown handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is bug fix for an invalid boundry check for WPS IE.
We should check max IE length against defined macro; instead we were
checking it against size of pointer. Fix it.
Also move IE length check before allocation of memory.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During P2P handshake, P2P client needs to send deauth after EAPOL
FAILURE to GO. We need add bss mode for P2P client when handle deauth
request.
Without this change, deauth can not be sent out from P2P client side.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before sending command to firmware, we need to check the frame type.
We skip registering the mgmt frame that has already been registered.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some GO will send deauth or disassoc packet at the end of WPS
handshake, which causes P2P connecion failure due to the race
condition between event path and data path.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In function 'mwifiex_write_data_complete' it need tx info to find
the mwifiex_private to updates statistics and wake up tx queues.
Or we may trigger tx queues timeout when transmitting lots of mgmt
frames.
Signed-off-by: Huawei Yang <harvey.huawei.yang@gmail.com>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete packets from TX queues for this mwifiex_private structure
when bridged packet count reaches maximum threshold. Bridged packets
from each RA List are deleted till they fall to low threshold of 128.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Maintain total outstanding packet count for RA list instead of total
outstanding size as packet count metric seems more reasonable for
checking threshold etc.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pkt_count is used to determine if BA can be formed on this RA list
by comparing it with randomly generated BA threshold. The pkt_count
variable name here is ambiguous and does not reflect its usage
correctly. Rename it to ba_pkt_count.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Under uAP mode mwifiex may stop all net tx queues on forwarding
packets. This may stop some tx queues and they never have chance
to be waked up. There is also no need to check tx_pending and
stop queues here. Because local host has such kind of check when
transmitting packets and it's not proper to have forwarding affect
local transmitting.
Signed-off-by: Huawei Yang <harvey.huawei.yang@gmail.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert the mwifiex/pci driver to use dev_pm_ops for power management and
remove Legacy PM handling. This change re-uses existing suspend and resume
interfaces for dev_pm_ops, and changes CONFIG_PM ifdefs to CONFIG_PM_SLEEP
as the driver does not support run-time PM.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During tear down (e.g. mwifiex_sdio_remove during system suspend),
mwifiex left IRQs enabled for a significant period of time when it was
unable to handle them correctly. This caused interrupt storms and
interfered with the bluetooth interface on the same SDIO card.
Solve this by disabling interrupts at the point when they can no longer
be handled correctly, which is at the start of mwifiex_remove_card().
For cleanliness, we now enable interrupts in the mwifiex_add_card() path,
to be symmetrical with the disabling of interrupts. We also couple the
registration of the sdio IRQ handler with the actual enable/disable of
interrupts at the hardware level.
I also removed a write to this register in mwifiex_init_sdio which seemed
pointless and won't cause any ill effects now that we only register
the SDIO IRQ handler when we are ready to accept interrupts.
Includes some corrections from Amitkumar Karwar.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently packet patterns and it's enum/structures are used only
for WoWLAN feature. As we intend to reuse them for new feature
packet coalesce, they are renamed in this patch.
Older names are kept for backward compatibility purpose.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
After receiving channel switch announcement from AP, scan and
association on that channel is blocked for DFS_CHAN_MOVE_TIME
(10 seconds). Hence station will be able to connect to the AP,
once it is moved to new channel.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds code to parse requested AP's 11h capabilities
and add 11h information in association request.
Also, deauth is sent to the AP after receiving channel switch
announcement event from firmware. This happens when AP advertises
WLAN_EID_CHANNEL_SWITCH IE in it's beacon.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use negative check (if(!bss_desc)) and return failure
instead of failing a NULL check later in
mwifiex_check_network_compatibility() routine.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When trying to unset a previously-set multicast list (i.e. the new list
has 0 entries), mwifiex_set_multicast_list() was calling down to
mwifiex_request_set_multicast_list() while leaving
mcast_list.num_multicast_addr as an uninitialized value.
We were arriving at mwifiex_cmd_mac_multicast_adr() which would then
proceed to do an often huge memcpy of
mcast_list.num_multicast_addr*ETH_ALEN bytes, causing memory corruption
and hard to debug crashes.
Fix this by setting mcast_list.num_multicast_addr to 0 when no multicast
list is provided. Similarly, fix up the logic in
mwifiex_request_set_multicast_list() to unset the multicast list that
was previously sent to the hardware in such cases.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bing Zhao
John W. Linville
Tobias Waldekranz
Avinash Patil
Amitkumar Karwar
Vladimir Kondratiev
Stone Piao
Tomasz Moń
Huawei Yang
Shuah Khan
Daniel Drake