When suspending, tpm_infineon calls the generic suspend function of the
TPM framework. However, the TPM framework does not return and the system
hangs upon suspend. When sending the necessary command "TPM_SaveState"
directly within the driver, suspending and resuming works fine.
Signed-off-by: Marcel Selhorst <m.selhorst@sirrix.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Debora Velarde <debora@linux.vnet.ibm.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: <stable@kernel.org> [2.6.32.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An unfortunate "WARNING" in the message amd64_edac dumps when the system
doesn't support DRAM ECC or ECC checking is not enabled in the BIOS
used to trigger kerneloops which qualified the message as an OOPS thus
misleading the users. See, e.g.
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/422536http://bugzilla.kernel.org/show_bug.cgi?id=15238
Downgrade the message level to KERN_NOTICE and fix the formulation.
Cc: stable@kernel.org # .32.x
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Use proper values to initialize bool configuration variables, tabs rather than
spaces, no braces for one-line else clause, __set_bit() when the operation
doesn't have to be atomic, input_set_abs_params() rather than writing the
fields directly, and call hid_hw_stop() when appropriate to handle failures in
the probe.
Signed-off-by: Michael Poole <mdpoole@troilus.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch corrects a userspace pointer dereference in the VGA arbiter
in 2.6.32.1.
copy_from_user() is used at line 822 to copy the contents of buf into
kbuf, but a call to strncmp() on line 964 uses buf rather than kbuf. This
problem led to a GPF in strncmp() when X was started on my x86_32 systems.
X triggered the behavior with a write of "target PCI:0000:01:00.0" to
/dev/vga_arbiter.
The patch has been tested against 2.6.32.1 and observed to correct the GPF
observed when starting X or manually writing the string "target
PCI:0000:01:00.0" to /dev/vga_arbiter.
Signed-off-by: Andy Getzendanner <james.getzendanner@students.olin.edu>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-linus' of ../drm-next:
drm/radeon/kms: retry auxch on 0x20 timeout value.
drm/radeon: Skip dma copy test in benchmark if card doesn't have dma engine.
drm/radeon/kms: fix screen clearing before fbcon.
drm/radeon/kms: add quirk for VGA without DDC on rv730 XFX card.
drm/radeon/kms: don't crash if no DDC bus on VGA/DVI connector.
drm/radeon/kms: change Kconfig text to reflect the new option.
drm/radeon/kms: suspend and resume audio stuff
ATOM appears to return 0x20 which seems to mean some sort of timeout.
retry the transaction up to 10 times before failing, this
makes DP->VGA convertor we bought work at least a bit more predictably.
Signed-off-by: Dave Airlie <airlied@redhat.com>
radeon_copy_dma is only available for r200 or newer cards.
Call to radeon_copy_dma would result to NULL pointer
dereference if benchmarking asic without dma engine.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/for-airlied' of /home/airlied/kernel/drm-next:
nouveau: fix state detection with switchable graphics
drm/nouveau: move dereferences after null checks
drm/nv50: make the pgraph irq handler loop like the pre-nv50 version
drm/nv50: delete ramfc object after disabling fifo, not before
drm/nv50: avoid unloading pgraph context when ctxprog is running
drm/nv50: align size of buffer object to the right boundaries.
drm/nv50: disregard dac outputs in nv50_sor_dpms()
drm/nv50: prevent multiple init tables being parsed at the same time
drm/nouveau: make dp auxch xfer len check for reads only
drm/nv40: make INIT_COMPUTE_MEM a NOP, just like nv50
drm/nouveau: Add proper vgaarb support.
drm/nouveau: Fix fbcon on mixed pre-NV50 + NV50 multicard.
drivers/gpu/drm/nouveau/nouveau_grctx.c: correct NULL test
drm/nouveau: call ttm_bo_wait with the bo lock held to prevent hang
drm/nouveau: Fixup semaphores on pre-nv50 cards.
drm/nouveau: Add getparam to get available PGRAPH units.
drm/nouveau: Add module options to disable acceleration.
drm/nouveau: fix non-vram notifier blocks
Even if this bumps the version to 1 it does not mean the driver is
out of staging. From what we know this is the last backwards
incompatible change to the driver.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When time-based throttling is implemented, we need to bump minor.
When the old way of detecting scanout is removed, we need to bump major.
In the meantime, this change should not break existing user-space.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This will prevent things from falling over if the user frees the flip
buffer before we complete the flip, since we'll hold an internal
reference.
Reported-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit cbda12d77e (drm/i915: implement
new pm ops for i915) introduced the problem that if s2disk hibernation
is aborted, the system will crash, because i915_pm_freeze() does
nothing, while it should at least reverse some operations carried out
by i915_suspend().
Fix this issue by splitting the i915 suspend into a freeze part a
suspend part, where the latter is not executed before creating a
hibernation image, and the i915 resume into a "low-level" resume part
and a thaw part, where the former is not executed after the image has
been created.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
This memset_io was added to debug something way back and got
left behind, memset the fb to black so the borders don't be all white.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The MI_DISPLAY_FLIP command needs to be set the same pipe
source image like in pipe source register, e.g source image
size minus one. This fixes screen corrupt issue on Ironlake.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
On Ironlake plane flip interrupt means flip done event already, the
behavior is not like old chips, and perform like other usual interrupt.
So only need to handle flip done event when receiving that interrupt.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
When a new page flip is requested, we need to both queue an unpin for
the current framebuffer, and also increment the flip pending count on
the newly submitted buffer.
At flip finish time, we need to unpin the old fb and decrement the flip
pending count on the new buffer.
The old code was conflating the two, and led to hangs when new direct
rendered apps were started, replacing the existing frame buffer. This
patch splits out the buffers and prevents the hangs.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
On 945, we need to avoid entering self-refresh if the compressor is
busy, or we may cause display FIFO underruns leading to ugly flicker.
Fixes fdo bug #24314, kernel bug #15043.
Tested-by: Alexander Lam <lambchop468@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Julien Cristau <jcristau@debian.org> (fd.o #25371)
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
An untiled framebuffer must be aligned to 64k. This is normally handled
by intel_pin_and_fence_fb_obj(), but the intelfb_create() likes to be
different and do the pinning itself. However, it aligns the buffer
object incorrectly for pre-i965 chipsets causing a PGTBL_ERR when it is
installed onto the output.
Fixes:
KMS error message while initializing modesetting -
render error detected: EIR: 0x10 [i915]
http://bugs.freedesktop.org/show_bug.cgi?id=22936
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
Before changing the status of a buffer with a pending write we will await
upon a new flush for that buffer. So we can take advantage of any flushes
posted whilst the buffer is active and pending processing by the GPU, by
clearing its write_domain and updating its last_rendering_seqno -- thus
saving a potential flush in deep queues and improves flushing behaviour
upon eviction for both GTT space and fences.
In order to reduce the time spent searching the active list for matching
write_domains, we move those to a separate list whose elements are
the buffers belong to the active/flushing list with pending writes.
Orignal patch by Chris Wilson <chris@chris-wilson.co.uk>, forward-ported
by me.
In addition to better performance, this also fixes a real bug. Before
this changes, i915_gem_evict_everything didn't work as advertised. When
the gpu was actually busy and processing request, the flush and subsequent
wait would not move active and dirty buffers to the inactive list, but
just to the flushing list. Which triggered the BUG_ON at the end of this
function. With the more tight dirty buffer tracking, all currently busy and
dirty buffers get moved to the inactive list by one i915_gem_flush operation.
I've left the BUG_ON I've used to prove this in there.
References:
Bug 25911 - 2.10.0 causes kernel oops and system hangs
http://bugs.freedesktop.org/show_bug.cgi?id=25911
Bug 26101 - [i915] xf86-video-intel 2.10.0 (and git) triggers kernel oops
within seconds after login
http://bugs.freedesktop.org/show_bug.cgi?id=26101
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Adam Lantos <hege@playma.org>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
Got Ironlake DPLL parameter table, which reflects the hardware
optimized values. So this one trys to list DPLL parameters for
different output types, should potential fix clock issue seen
on new Arrandale CPUs.
This fixes DPLL setting failure on one 1920x1080 dual channel
LVDS for Ironlake. Test has also been made on LVDS panels with
smaller size and CRT/HDMI/DP ports for different monitors on
their all supported modes.
Update:
- Change name of double LVDS to dual LVDS.
- Fix SSC 120M reference clock to use the right range.
Cc: CSJ <changsijay@gmail.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Revert the following change from commit 6f8372b6 ("RDMA/cm: fix
loopback address support")
The defined behavior of rdma_bind_addr is to associate an RDMA
device with an rdma_cm_id, as long as the user specified a non-
zero address. (ie they weren't just trying to reserve a port)
Currently, if the loopback address is passed to rdma_bind_addr,
no device is associated with the rdma_cm_id. Fix this.
It turns out that important apps such as Open MPI depend on
rdma_bind_addr() NOT associating any RDMA device when binding to a
loopback address. Open MPI is being updated to deal with this, but at
least until a new Open MPI release is available, maintain the previous
behavior: allow rdma_bind_addr() to succeed, but do not bind to a
device.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
cohd_fin has already been verified not to be NULL, so the argument to
BUG_ON cannot be true.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression *x;
expression e;
identifier l;
@@
if (x == NULL || ...) {
... when forall
return ...; }
... when != goto l;
when != x = e
when != &x
*x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If submitting new buffer failed, a wrong descriptor gets completed and it
doesn't check, if a callback is at all defined, which can lead to an Oops. Fix
these bugs and make ipu_update_channel_buffer() void, because it never fails.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch fixes two potential races in the velocity driver:
* Move the ACK and error handler to the interrupt handler. This fixes a
potential race with shared interrupts when the other device interrupts
before the NAPI poll handler has finished. As the velocity driver hasn't
acked it's own interrupt, it will then steal the interrupt from the
other device.
* Use spin_lock_irqsave in velocity_poll. In the current code, the
interrupt handler will deadlock if e.g., the NAPI poll handler is
executing when an interrupt (for another device) comes in since it
tries to take the already held lock.
Also unlock the spinlock only after enabling the interrupt in
velocity_poll.
The error path is moved to the interrupt handler since this is where the
ISR is checked now.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Anders Grafstrom <anders.grafstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
velocity_set_coalesce touches ISR and some other sensitive registers not
covered by the rtnl lock, so take the velocity spinlock.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new RTL8187B device.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MODULE_VERSION doesn't make too much sense for drivers merged
into main tree, as git is much better tracking revisions than
any developer might ever be.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make Apple MagicMouse Kconfig entry consistent with other dirvers.
Also expand the tristate text a little bit more, so that it doesn't
clash with already existing HID_APPLE.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Magic Mouse requires that a driver send an unlock Report(Feature) command,
similar to the Wacom wireless tablet and Sixaxis controller quirks. This turns
on an Input Report that isn't published in the input Report descriptor that
contains touch data (and usually overrides the normal motion and click Report).
Because the mouse has only one switch and no scroll wheel, the driver
(under control of parameters) emulates a middle button and scroll wheel.
User space could also ignore and/or re-synthesize those events based on
the reported events.
Some user-space tools to talk to the mouse directly (that is, when it is not
associated with the host's HIDP stack) are at
http://github.com/entrope/linux-magicmouse
Signed-off-by: Michael Poole <mdpoole@troilus.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Apple Magic Mouse (and probably other devices) publish reports that are not
called out in their HID report descriptors -- they only send them when enabled
through other writes to the device. This allows a driver to handle these
unlisted reports.
Signed-off-by: Michael Poole <mdpoole@troilus.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added support for MosArt dual-touch panels, present in the Asus T91MT notebook.
Signed-off-by: Stephane Chatty <chatty@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fixed stupid copy-paste bug in touchscreen emulation for the Stantum multitouch
panel: a flag was reset just before being tested.
Signed-off-by: Stephane Chatty <chatty@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
======
This fix is related to
http://bugzilla.kernel.org/show_bug.cgi?id=15142
but does not address that exact issue.
======
sysfs does like attributes being removed while they are being accessed
(i.e. read or written) and waits for the access to complete.
As accessing some md attributes takes the same lock that is held while
removing those attributes a deadlock can occur.
This patch addresses 3 issues in md that could lead to this deadlock.
Two relate to calling flush_scheduled_work while the lock is held.
This is probably a bad idea in general and as we use schedule_work to
delete various sysfs objects it is particularly bad.
In one case flush_scheduled_work is called from md_alloc (called by
md_probe) called from do_md_run which holds the lock. This call is
only present to ensure that ->gendisk is set. However we can be sure
that gendisk is always set (though possibly we couldn't when that code
was originally written. This is because do_md_run is called in three
different contexts:
1/ from md_ioctl. This requires that md_open has succeeded, and it
fails if ->gendisk is not set.
2/ from writing a sysfs attribute. This can only happen if the
mddev has been registered in sysfs which happens in md_alloc
after ->gendisk has been set.
3/ from autorun_array which is only called by autorun_devices, which
checks for ->gendisk to be set before calling autorun_array.
So the call to md_probe in do_md_run can be removed, and the check on
->gendisk can also go.
In the other case flush_scheduled_work is being called in do_md_stop,
purportedly to wait for all md_delayed_delete calls (which delete the
component rdevs) to complete. However there really isn't any need to
wait for them - they have already been disconnected in all important
ways.
The third issue is that raid5->stop() removes some attribute names
while the lock is held. There is already some infrastructure in place
to delay attribute removal until after the lock is released (using
schedule_work). So extend that infrastructure to remove the
raid5_attrs_group.
This does not address all lockdep issues related to the sysfs
"s_active" lock. The rest can be address by splitting that lockdep
context between symlinks and non-symlinks which hopefully will happen.
Signed-off-by: NeilBrown <neilb@suse.de>
Unset the bit that indicates that a ctxprog can continue at the end.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
ramfc is zero'ed upon destruction, so it's safer to do things in the right
order.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
- We need to disable pgraph fifo access before checking the current channel,
otherwise we could still hit a running ctxprog.
- The writes to 0x400500 are already handled by pgraph->fifo_access and are
therefore redundant, moreover pgraph fifo access should not be reenabled
before current context is set as invalid. So remove them altogether.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
- In the current situation the padding that is added is dangerous to write
to, userspace could potentially overwrite parts of another bo.
- Depth and stencil buffers are supposed to be large enough in general so
the waste of memory should be acceptable.
- Alternatives are hiding the padding from users or splitting vram into 2
zones.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes DVI+VGA on my 9400, and likely a lot of other configurations that
got broken by the previos DVI-over-DP fix.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
With DVI and DP plugged, the DVI clock change interrupts being run can
cause DP link training to fail. This adds a spinlock around init table
parsing to prevent this.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The wrong pointer was tested.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, PAE frames are not assigned proper sequence numbers.
Since sending PAE frames as part of aggregates breaks
crupto with several APs, they are sent as normal MPDUs.
Fix the seqeuence number issue by updating the frame with the
internal sequence number.
Tested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding a mapping for the 'AL Network Chat' usage from the 'Consumer' usage
page (USB HID Usage Tables v1.11). This usage is used by some keyboards for
a multimedia key.
Signed-off-by: Leo P White <lpw25@cam.ac.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If a CHPID is offline during a device shutdown the ccw_device_halt|clear
may fail and the qdio device stays in state STOPPED until the shutdown is
finished. If an interrupt occurs before the device is set to INACTIVE
the STOPPED state triggers a WARN_ON in the interrupt handler.
Prevent this WARN_ON by catching the STOPPED state in the interrupt
handler.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Inbound traffic handling may hang if next buffer to check is in
state ERROR, polling is stopped and the final check for further
available inbound buffers disregards buffers in state ERROR.
This patch includes state ERROR when checking availability of
more inbound buffers.
Cc: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Test the value that was just allocated rather than the previously tested one.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression *x;
expression e;
identifier l;
@@
if (x == NULL || ...) {
... when forall
return ...; }
... when != goto l;
when != x = e
when != &x
*x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify the HW checksum state for frames handed to GRO processing.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code was written long ago when it was not possible to
reshape a degraded array. Now it is so the current level of
degraded-ness needs to be taken in to account. Also newly addded
devices should only reduce degradedness if they are deemed to be
in-sync.
In particular, if you convert a RAID5 to a RAID6, and increase the
number of devices at the same time, then the 5->6 conversion will
make the array degraded so the current code will produce a wrong
value for 'degraded' - "-1" to be precise.
If the reshape runs to completion end_reshape will calculate a correct
new value for 'degraded', but if a device fails during the reshape an
incorrect decision might be made based on the incorrect value of
"degraded".
This patch is suitable for 2.6.32-stable and if they are still open,
2.6.31-stable and 2.6.30-stable as well.
Cc: stable@kernel.org
Reported-by: Michael Evans <mjevans1983@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
It appears we aren't required to do memory sizing ourselves on nv40
either. NV40 init tables read a strap from PEXTDEV_BOOT_0 into a
CRTC register, and then later use that value to select a memory
configuration (written to PFB_CFG0, just like INIT_COMPUTE_MEM on
earlier cards) with INIT_IO_RESTRICT_PROG.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We used single shared fbops struct and patched it at fb init time with
pointers to the right variant. On mixed multicard, this meant that
it was either sending NV50-style commands to all cards, or NV04-style
commands to all cards.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Test the just-allocated value for NULL rather than some other value.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,y;
statement S;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
(
if ((x) == NULL) S
|
if (
- y
+ x
== NULL)
S
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: David Airlie <airlied@linux.ie>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nouveau_gem_ioctl_cpu_prep calls ttm_bo_wait without the bo lock held.
ttm_bo_wait unlocks that lock, and so must be called with it held.
Currently this bug causes libdrm nouveau_bo_busy() to hang the machine.
Signed-off-by: Luca Barbieri <luca at luca-barbieri.com>
Acked-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Apparently, they generate a PFIFO interrupt each time one of the
semaphore methods is executed if its ctxdma wasn't manually marked as
valid. This patch makes it flip the valid bit in response to the
DMA_SEMAPHORE method (which triggers the IRQ even for a valid ctxdma).
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On nv50, this will be needed by applications using CUDA to know
how much stack/local memory to allocate.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
noaccel=1 disables all acceleration and doesn't even attempt
initialising PGRAPH+PFIFO, nofbaccel=1 only makes fbcon unaccelerated.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Due to a thinko, these were previously forced to VRAM even if we allocated
them in GART.
This commit fixes that bug, but keeps the previous behaviour of using VRAM
by default until it's been tested properly across more chipsets.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is strange - like really really strange, twilight zone of strange.
VGA ports have DDC buses, but sometimes for some reasons the BIOS
says we don't and we oops - AMD mentioned bios bugs so we'll have
to add quirks.
reported on irc by nirbheek and
https://bugzilla.redhat.com/show_bug.cgi?id=554323
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Fix ondemand to not request targets outside policy limits
[CPUFREQ] Fix use after free of struct powernow_k8_data
[CPUFREQ] fix default value for ondemand governor
iwl_set_rxon_ht() only get called in iwl_post_associate(); which cause
possible incorrect ht configuration. Adding the call in iwl_mac_config() if
IEEE80211_CONF_CHANGE_CHANNEL flag is set to re-configure and send rxon
command.
Fixes
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2146
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Original code incorrectly assumed only status-type-0
IOCBs would be queued to the response-queue, and thus all
entries would safely reference a VHA from the IOCB
'handle.'
Cc: stable@kernel.org
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The status FC_CTELS_STATUS_REJECT for all FC BSG errors is not
appropriate. Instead, report -EIO in the result field if there was a
problem in zfcp with the FC BSG request. If the request is good from
our point of view, report result 0, status FC_CTELS_STATUS_OK and let
userspace read the Accept or Reject from the payload (as documented in
scsi_bsg_fc.h).
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
retval should be SUCCESS/FAILED which is defined at scsi.h
retval = 0 is directing wrong return value. It must be retval = SUCCESS.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'v4l_for_linus' of git://linuxtv.org/fixes:
V4L/DVB: dvb-core: fix initialization of feeds list in demux filter
V4L/DVB: dvb_demux: Don't use vmalloc at dvb_dmx_swfilter_packet
V4L/DVB: Fix the risk of an oops at dvb_dmx_release
* 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Remove superfluous setup_frame_reg call
sh: Don't continue unwinding across interrupts
sh: Setup frame pointer in handle_exception path
sh: Correct the offset of the return address in ret_from_exception
usb: r8a66597-hcd: Fix up spinlock recursion in root hub polling.
usb: r8a66597-hcd: Flush the D-cache for the pipe-in transfer buffers.
A DVB demultiplexer device can be used to set up either a PES filter or
a section filter. In the former case, the ts field of the feed union of
struct dmxdev_filter is used, in the latter case the sec field of the
same union is used.
The ts field is a struct list_head, and is currently initialized in the
open() method of the demux device. When for a given demuxer a section
filter is set up, the sec field is played with, thus if a PES filter
needs to be set up after that the ts field will be corrupted, causing a
kernel oops.
This fix moves the list head initialization to
dvb_dmxdev_pes_filter_set(), so that the ts field is properly
initialized every time a PES filter is set up.
Signed-off-by: Francesco Lavra <francescolavra@interfree.it>
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Walls <awalls@radix.net>
Tested-by: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As dvb_dmx_swfilter_packet() is protected by a spinlock, it shouldn't sleep.
However, vmalloc() may call sleep. So, move the initialization of
dvb_demux::cnt_storage field to a better place.
Reviewed-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dvb_dmx_init tries to allocate virtual memory for 2 pointers: filter and feed.
If the second vmalloc fails, filter is freed, but the pointer keeps pointing
to the old place. Later, when dvb_dmx_release() is called, it will try to
free an already freed memory, causing an OOPS.
Reviewed-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set state of the device as "initializing" during and after cleanup
to ensure that unsolicited data from the device is not passed on.
We especially want to avoid processing new device announcements
"0xaa 0x00" that can come up before we perform reconnect operation.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Ingo pointed out that we really don't give the user enough warning to make
a decision here. So revise the Kconfig text with a better warning.
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 7036251180 ("tty: fix race in tty_fasync") and
commit b04da8bfdf ("fnctl: f_modown should call write_lock_irqsave/
restore") that tried to fix up some of the fallout but was incomplete.
It turns out that we really cannot hold 'tty->ctrl_lock' over calling
__f_setown, because not only did that cause problems with interrupt
disables (which the second commit fixed), it also causes a potential
ABBA deadlock due to lock ordering.
Thanks to Tetsuo Handa for following up on the issue, and running
lockdep to show the problem. It goes roughly like this:
- f_getown gets filp->f_owner.lock for reading without interrupts
disabled, so an interrupt that happens while that lock is held can
cause a lockdep chain from f_owner.lock -> sighand->siglock.
- at the same time, the tty->ctrl_lock -> f_owner.lock chain that
commit 7036251180 introduced, together with the pre-existing
sighand->siglock -> tty->ctrl_lock chain means that we have a lock
dependency the other way too.
So instead of extending tty->ctrl_lock over the whole __f_setown() call,
we now just take a reference to the 'pid' structure while holding the
lock, and then release it after having done the __f_setown. That still
guarantees that 'struct pid' won't go away from under us, which is all
we really ever needed.
Reported-and-tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Américo Wang <xiyou.wangcong@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Fix leak of relocs along do_execbuffer error path
drm/i915: slow acpi_lid_open() causes flickering - V2
drm/i915: Disable SR when more than one pipe is enabled
drm/i915: page flip support for Ironlake
drm/i915: Fix the incorrect DMI string for Samsung SX20S laptop
drm/i915: Add support for SDVO composite TV
drm/i915: don't trigger ironlake vblank interrupt at irq install
drm/i915: handle non-flip pending case when unpinning the scanout buffer
drm/i915: Fix the device info of Pineview
drm/i915: enable vblank interrupt on ironlake
drm/i915: Prevent use of uninitialized pointers along error path.
drm/i915: disable hotplug detect before Ironlake CRT detect
Use DECLARE_WAIT_QUEUE_HEAD_ONSTACK to make lockdep happy
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Different motherboards have different PNP declarations for
W83781D/W83782D chips. Some declare the whole range of I/O ports (8
ports), some declare only the useful ports (2 ports at offset 5) and
some declare fancy ranges, for example 4 ports at offset 4. To
properly handle all cases, request all ports individually for probing.
After we have determined that we really have a W83781D or W83782D
chip, the useful port range will be requested again, as a single
block.
I did not see a board which needs this yet, but I know of one for lm78
driver and I'd like to keep the logic of these two drivers in sync.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Different motherboards have different PNP declarations for LM78/LM79
chips. Some declare the whole range of I/O ports (8 ports), some
declare only the useful ports (2 ports at offset 5) and some declare
fancy ranges, for example 4 ports at offset 4. To properly handle all
cases, request all ports individually for probing. After we have
determined that we really have an LM78 or LM79 chip, the useful port
range will be requested again, as a single block.
This fixes the driver on the Olivetti M3000 DT 540, at least.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
The #define ADT7462_VOLT_COUNT is wrong, it should be 13 not 12. All the
for loops that use this as a limit count are of the typical form, "for
(n = 0; n < ADT7462_VOLT_COUNT; n++)", so to loop through all voltages
w/o missing the last one it is necessary for the count to be one greater
than it is. (Specifically, you will miss the +1.5V 3GPIO input with count
= 12 vs. 13.)
Signed-off-by: Ray Copeland <ray.copeland@aprius.com>
Acked-by: "Darrick J. Wong" <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
The functionality bit vector is always returned as a little-endian
32-bit number by the device, so it must be byte-swapped to the host
endianness.
On the other hand, the delay value is handled by the USB stack, so no
byte swapping is needed on our side.
This fixes bug #15105:
http://bugzilla.kernel.org/show_bug.cgi?id=15105
Reported-by: Jens Richter <jens@richter-stutensee.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Jens Richter <jens@richter-stutensee.de>
Cc: Till Harbaum <till@harbaum.org>
Cc: stable@kernel.org
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] Call flush_dcache_page after PIO data transfers in libata-sff.c
ahci: add Acer G725 to broken suspend list
libata: fix ata_id_logical_per_physical_sectors
libata-scsi passthru: fix bug which truncated LBA48 return values
The new cs5535-* drivers use PCI header config info rather than MSRs to
determine the memory region to use for things like GPIOs and MFGPTs. As
anticipated, we've run into a buggy BIOS:
[ 0.081818] pci 0000:00:14.0: reg 10: [io 0x6000-0x7fff]
[ 0.081906] pci 0000:00:14.0: reg 14: [io 0x6100-0x61ff]
[ 0.082015] pci 0000:00:14.0: reg 18: [io 0x6200-0x63ff]
[ 0.082917] pci 0000:00:14.2: reg 20: [io 0xe000-0xe00f]
[ 0.083551] pci 0000:00:15.0: reg 10: [mem 0xa0010000-0xa0010fff]
[ 0.084436] pci 0000:00:15.1: reg 10: [mem 0xa0011000-0xa0011fff]
[ 0.088816] PCI: pci_cache_line_size set to 32 bytes
[ 0.088938] pci 0000:00:14.0: address space collision: [io 0x6100-0x61ff] already in use
[ 0.089052] pci 0000:00:14.0: can't reserve [io 0x6100-0x61ff]
This is a Soekris board, and its BIOS sets the size of the PCI ISA bridge
device's BAR0 to 8k. In reality, it should be 8 bytes (BAR0 is used for
SMBus stuff). This quirk checks for an incorrect size, and resets it
accordingly.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Tested-by: Leigh Porter <leigh@leighporter.org>
Tested-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: fix r300 vram width calculations
drm/radeon/kms: rs400/480 MC setup is different than r300.
drm/radeon/kms: make initial state of load detect property correct.
drm/radeon/kms: disable HDMI audio for now on rv710/rv730
drm/radeon/kms: don't call suspend path before cleaning up GPU
drivers/gpu/drm/radeon/radeon_combios.c: fix warning
ati_pcigart: fix printk format warning
drm/r100/kms: Emit cache flush to the end of command buffer. (v2)
drm/radeon/kms: fix regression rendering issue on R6XX/R7XX
drm/radeon/kms: move blit initialization after we disabled VGA
It is possible (and expected) for there to be holes in the h->drv[]
array, that is, some elements may be NULL pointers. cciss_seq_show
needs to be made aware of this possibility to avoid an Oops.
To reproduce the Oops which this fixes:
1) Create two "arrays" in the Array Configuratino Utility and
several logical drives on each array.
2) cat /proc/driver/cciss/cciss* in an infinite loop
3) delete some of the logical drives in the first "array."
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Boot testing on my rs480 laptop found the MC idle never happened
on startup, a quick check with AMD found the idle bit is in a different
place on the rs4xx than r300.
Implement a new rs400 mc idle function to fix this.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current root hub polling code exhibits a spinlock recursion on the
private controller lock. r8a66597_root_hub_control() is called from
r8a66597_timer() which grabs the lock and disables IRQs. The following
chain emerges:
r8a66597_timer() <-- lock taken
r8a66597_root_hub_control()
r8a66597_check_syssts()
usb_hcd_poll_rh_status() <-- acquires the same lock
/* insert death here */
The entire chain requires IRQs to be disabled, so we just unlock and
relock around the call to usb_hcd_poll_rh_status() while leaving the
IRQ state unchanged.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
This implements the same D-cache flushing logic for r8a66597-hcd as
Catalin's isp1760 (http://patchwork.kernel.org/patch/76391/) change,
with the same note applying here as well:
When the HDC driver writes the data to the transfer buffers it
pollutes the D-cache (unlike DMA drivers where the device writes
the data). If the corresponding pages get mapped into user space,
there are no additional cache flushing operations performed and
this causes random user space faults on architectures with
separate I and D caches (Harvard) or those with aliasing D-cache.
This fixes up crashes during USB boot on SH7724 and others:
http://marc.info/?l=linux-sh&m=126439837308912&w=2
Reported-by: Goda Yusuke <goda.yusuke@renesas.com>
Tested-by: Goda Yusuke <goda.yusuke@renesas.com>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
In suspend path we unmap the GART table while in cleaning up
path we will unbind buffer and thus try to write to unmapped
GART leading to oops. In order to avoid this we don't call the
suspend path in cleanup path. Cleanup path is clever enough
to desactive GPU like the suspend path is doing, thus this was
redondant.
Tested on: RV370, R420, RV515, RV570, RV610, RV770 (all PCIE)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/radeon/radeon_combios.c: In function 'radeon_combios_get_lvds_info':
drivers/gpu/drm/radeon/radeon_combios.c:893: warning: comparison is always false due to limited range of data type
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix ati_pcigart printk format warning:
drivers/gpu/drm/ati_pcigart.c:115: warning: format '%Lx' expects type 'long long unsigned int', but argument 3 has type 'dma_addr_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cache flush is required in case CPU is accessing rendered data.
This fixes glean/readPixSanity test case and random rendering
errors in sauerbraten and warzone2100.
v2 Fix comment ordering in r100_fence_ring_emit and remove extra
defines added in first version.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It seems that some R6XX/R7XX silently ignore HDP flush when
programmed through ring, this patch addback an ioctl callback
to allow R6XX/R7XX hw to perform such flush through MMIO in
order to fix a regression. For more details see:
http://bugzilla.kernel.org/show_bug.cgi?id=15186
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
VGA might be overwritting VRAM and corrupt our blit shader leading
to corruption, it likely won't happen if you load fbcon right after
radeon. Thanks to Shawn Starr and Andre Maasikas for tracking down
this issue.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This device generates ABS_Z and ABS_RX events, while it should be
generating ABS_X and ABS_Y instead. Using the MULTI_INPUT quirk solves
this issue.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Daniel Oliveira Nascimento <don@syst.com.br>
[jkosina@suse.cz: fixed blacklist ordering while resolving conflict]
[jkosina@suse.cz: fixed typo to make it compile]
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This change corrects an issue that will cause false hangs when using either
82575 or 82580 in legacy interrupt mode. The issue is caused when there is
a slow traffic flow and an "ethtool -r" is executed while using legacy or
MSI interrupts. MSI-X is not affected by this issue due to the fact that
we were already reconfiguring the vectors after reset.
If possible it would be best to push this for net-2.6 since it is resolving
a bug but if that is not possible then net-next-2.6 will be fine.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following a gpu hang, we would leak the relocation buffer. So simply
earrange the error path to always free the relocation buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
acpi_lid_open() could take up to 10ms on my computer. Some component is
calling the drm GETCONNECTOR ioctl many times in a row. This results in
flickering (for example, when starting a video). Fix it by assuming an
always connected lid status.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Eric Anholt <eric@anholt.net>
Self Refresh should be disabled on dual plane configs. Otherwise, as
the SR watermark is not calculated for such configs, switching to non
VGA mode causes FIFO underrun and display flicker.
This fixes Korg Bug #14897.
Signed-off-by: David John <davidjon@xenontk.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
This fixes the regression introduced by commit
42590a7501 ("x86/agp: Fix
agp_amd64_init and agp_amd64_cleanup").
The commit 61684ceaad fixed the
above regression but it's not enough. When amd64-agp is built as
a module, AGP isn't initialized, iommu is initialized, all the
aperture is owned by the iommu.
Reported-by: Marin Mitov <mitov@issp.bas.bg>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Marin Mitov <mitov@issp.bas.bg>
LKML-Reference: <20100204090802S.fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
flush_dcache_page() must be called after (!ATA_TFLAG_WRITE) the
data copying to avoid D-cache aliasing with user space or I-D cache
coherency issues (when reading data from an ATA device using PIO,
the kernel dirties the D-cache but there is no flush_dcache_page()
required on Harvard architectures).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acer G725 shares the same suspend problem with the HP laptops which
lose ATA devices on resume. New firmware which fixes the problem is
already available. Add G725 with old firmwares to the broken suspend
list.
This problem has been reported in bko#15104.
http://bugzilla.kernel.org/show_bug.cgi?id=15104
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jani-Matti Hätinen <jani-matti.hatinen@iki.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix assignment which overwrote SAT ATA PASS-THROUGH command EXTEND
bit setting (ATA_TFLAG_LBA48)
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
a developer had complained of getting lots of warnings:
"eth16 selects TX queue 98, but real number of TX queues is 64"
http://www.mail-archive.com/e1000-devel@lists.sourceforge.net/msg02200.html
As there was no follow up on that bug, I am submitting this
patch assuming that the other return points will not return
invalid txq's, and also that this fixes the bug (not tested).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e5a43549f7 (ixgbe: remove
skb_dma_map/unmap calls from driver) looks to have introduced a bug in
ixgbe_tx_map. If we get an error from a PCI DMA call, we loop backwards
through count until it becomes -1 and return that.
The caller of ixgbe_tx_map expects 0 on error, so return that instead.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o context resources can be in used, while resource cleanup is in progress,
during fw recover.
o Null pointer execption can occur in send_cmd_desc, if fw recovery
module frees tx ring without rtnl lock.
o Same applies to ethtool register dump.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For NX2031, first try to scrub interrupt before requesting firmware
reset. Return statement was missing after scrubbbing interrupt.
Signed-off-by: Vernon Mauery <vernux@us.ibm.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The book keeping structure for transmit always had the flags value
cleared so transmit DMA maps were never released correctly.
Based on patch by Jarek Poplawski, problem observed by Michael Breuer.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a CONFIG_SSB_SDIOHOST typo.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Reported-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Tested-By: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit c7ab5ef9bc entitled "b43: implement
short slot and basic rate handling" reduced the transmit throughput for
my BCM4311 device from 18 Mb/s to 0.7 Mb/s. The basic rate handling
portion is OK, the problem is in the short slot handling.
Prior to this change, the short slot enable/disable routines were never
called. Experimentation showed that the critical part was changing the
value at offset 0x0010 in the shared memory. This is supposed to contain
the 802.11 Slot Time in usec, but if it is changed from its initial value
of zero, performance is destroyed. On the other hand, changing the value
in the MMIO register corresponding to the Interframe Slot Time increased
performance from 18 to 22 Mb/s. A BCM4306/3 also shows dramatic
improvement of the transmit rate from 5.3 to 19.0 Mb/s.
Other changes in the patch include removal of the magic number for the
MMIO register, and allowing the slot time to be set for any PHY operating
in the 2.4 GHz band. Previously, the routine was executed only for G PHYs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [Any stable version back through 2.6.28]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For historical reasons, we don't have most of the in-tree
drivers residing on hid-bus properly selectable in kernel
configuration unless CONFIG_EMBEDDED is set.
This has been introduced on Linus' request from 14 Oct
===
As to the Kconfig options - do they really add so much space that you need to
ask for the quirks? You didn't use to. Can you make the questions depend on
EMBEDDED, or at least on the HID_COMPAT thing or whatever?
===
This still makes perfect sense for small and tiny drivers, which
just fix report descriptors, fix up HID->input mappings that slightly
violates HUT standard, send one extra packet to the device that is
needed before it becomes functional, etc.
Since then, we have been gathering more and more HID-bus drivers,
which are full-fledged drivers. For these, the size argument becomes
more valid. Plus the devices are much more special than "just violates
HID specification in this one or two tiny unimportant points".
Therefore I am marking such drivers as properly selectable no matter
the setting of CONFIG_EMBEDDED, while keeping all the small and tiny
ones compiled by default.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
With Wacom tablet mode-setting moved from userspace into kernel,
we don't have to consider failures of device queries through the
_raw callback as hard failure, as the driver can safely continue
anyway.
This is consistent with the current USB driver in wacom_sys.c
Reported-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that hid_output_raw_report works, port the PS3 Sixaxis
Bluetooth quirk from user-space, into kernel-space.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hid-wacom driver required user-space to poke at the tablet
to make it send data about the cursor location.
This patch makes it do the same thing but in the kernel.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In commit 2da31939a4 ("Bluetooth: Implement raw output support for HIDP
layer"), support for Bluetooth hid_output_raw_report was added, but it
pushes the data to the intr socket instead of the ctrl one. This has been
fixed by 6bf8268f9a ("Bluetooth: Use the control channel for raw HID reports")
Still, it is necessary to distinguish whether the report in question should be
either FEATURE or OUTPUT. For this, we have to extend the generic HID API,
so that hid_output_raw_report() callback provides means to specify this
value so that it can be passed down to lower level hardware drivers (currently
Bluetooth and USB).
Based on original patch by Bastien Nocera <hadess@hadess.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added support for the Pixart Imaging Inc. Optical Touch Screen found in the MSI
AE2220 and other new all in one computers to the Quanta Optical Touch
dual-touch panel driver found in the latest git clone
git://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git.
Signed-off-by: Alex Neblett <alexneblett01@yahoo.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix typo in ioat2_quiesce. check 'tmo' is zero, not 'end'. Also applies
to 2.6.32.3
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (23 commits)
connector: Delete buggy notification code.
be2net: use eq-id to calculate cev-isr reg offset
Bluetooth: Use the control channel for raw HID reports
Bluetooth: Add DFU driver for Atheros Bluetooth chipset AR3011
Bluetooth: Redo checks in IRQ handler for shared IRQ support
Bluetooth: Fix memory leak in L2CAP
Bluetooth: Remove double free of SKB pointer in L2CAP
cdc_ether: Partially revert "usbnet: Set link down initially ..."
be2net: Fix memset() arg ordering.
bonding: bond_open error return value
ixgbe: if ixgbe_copy_dcb_cfg is going to fail learn about it early
ixgbe: set the correct DCB bit for pg tx settings
igbvf: fix issue w/ mapped_as_page being left set after unmap
drivers/net: ks8851_mll ethernet network driver
be2net: Bug fix to support newer generation of BE ASIC
starfire: clean up properly if firmware loading fails
mac80211: fix NULL pointer dereference when ftrace is enabled
netfilter: ctnetlink: fix expectation mask dump
ipv6: conntrack: Add member of user to nf_ct_frag6_queue structure
ath9k: fix eeprom INI values override for 2GHz-only cards
...
This is the counterpart to cba767175b
("pktcdvd: remove broken dev_t export of class devices"). Device is not
registered using dev_t, so it should not be destroyed using device_destroy
which looks up the device by dev_t. This will fail and adding the device
again will fail with the "duplicate name" error. This is fixed using
device_unregister instead of device_destroy.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The probe function passes a pointer to a struct fb_info to
platform_set_drvdata(), so don't interpret the return value of
platform_get_drvdata() as a pointer to struct imxfb_info.
The original imxfb_info *fbi backlight_power was NULL but in imxfb_suspend
it was 4 resulting in an oops as imxfb_suspend calls
imxfb_disable_controller(fbi) which in turn has
if (fbi->backlight_power)
fbi->backlight_power(0);
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
write_kmem() used to assume vwrite() always return the full buffer length.
However now vwrite() could return 0 to indicate memory hole. This
creates a bug that "buf" is not advanced accordingly.
Fix it to simply ignore the return value, hence the memory hole.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <tj@kernel.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Otherwise vmalloc_to_page() will BUG().
This also makes the kmem read/write implementation aligned with mem(4):
"References to nonexistent locations cause errors to be returned." Here we
return -ENXIO (inspired by Hugh) if no bytes have been transfered to/from
user space, otherwise return partial read/write results.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the kernel oops when dev_dbg is called with mx3_fbi->txd == NULL
Fix the late initialisation of mx3fb->backlight_level. If not, in the
chain of function started by init_fb_chan(), in __blank() call
sdc_set_brightness(mx3fb, mx3fb->backlight_level) that will shut down the
CONTRAST PWM output.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski <at> gmx.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Tue, Feb 02, 2010 at 02:57:14PM -0800, Greg KH (gregkh@suse.de) wrote:
> > There are at least two ways to fix it: using a big cannon and a small
> > one. The former way is to disable notification registration, since it is
> > not used by anyone at all. Second way is to check whether calling
> > process is root and its destination group is -1 (kind of priveledged
> > one) before command is dispatched to workqueue.
>
> Well if no one is using it, removing it makes the most sense, right?
>
> No objection from me, care to make up a patch either way for this?
Getting it is not used, let's drop support for notifications about
(un)registered events from connector.
Another option was to check credentials on receiving, but we can always
restore it without bugs if needed, but genetlink has a wider code base
and none complained, that userspace can not get notification when some
other clients were (un)registered.
Kudos for Sebastian Krahmer <krahmer@suse.de>, who found a bug in the
code.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device generates ABS_Z and ABS_RX events, while it should be
generating ABS_X and ABS_Y instead. Using the MULTI_INPUT quirk solves
this issue.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Daniel Oliveira Nascimento <don@syst.com.br>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
While debugging a dma driver I noticed a memleak after
unloading the driver module.
Caught by kmemleak.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cfq-iosched: Do not idle on async queues
blk-cgroup: Fix potential deadlock in blk-cgroup
block: fix bugs in bio-integrity mempool usage
block: fix bio_add_page for non trivial merge_bvec_fn case
drbd: null dereference bug
drbd: fix max_segment_size initialization
I happen to own a keyboard identified as 05af:3062 which is labeled as
"FlatX Coldless Combo" by "Prodige", which exhibits input problems without
NOGET quirk. For some reason, lsusb reports this device as "Jing-Mold
Enterprise Co., Ltd", which is not mentioned anywhere on the package.
A quick search on the intenet shows that there a other people who have
this in their lsusb output, but apparently they don't have the problem
I am seeing (or they are not such furious typists as myself).
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
cev-isr reg offset for each function is better calculated using (any) eq-id
alloted to that function instead of using pci-func number(which
does not work in some configurations...)
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves disable_controller() in the r8a66597-hdc
driver to disable all interrupts and clear status flags. It
also makes sure that disable_controller() is called during
probe(). This fixes the relatively rare case of unexpected
pending interrupts after kexec reboot.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The spi_sh_msiof.c driver presently misconfigures REDG and TEDG. TEDG==0
outputs data at the **rising edge** of the clock and REDG==0 samples data
at the **falling edge** of the clock. Therefore for SPI, TEDG must be
equal to REDG, otherwise the last byte received is not sampled in SPI
mode 3.
This brings the driver in line with the SH7723 HW Reference Manual
settings documented in Figures 20.20 and 20.21 ("SPI Clock and data
timing").
Signed-off-by: Markus Pietrek <Markus.Pietrek@emtrion.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In the transmit path of firewire-net (IPv4 over 1394), the following
race condition may occur:
- The networking soft IRQ inserts a datagram into the 1394 async
request transmit DMA.
- The 1394 async transmit completion tasklet runs to finish cleaning
up (unlink datagram from list of pending ones, release skb and
outbound 1394 transaction object) --- before the networking soft IRQ
had a chance to proceed and add the datagram to the list of pending
datagrams.
This caused a panic in the 1394 async transmit completion tasklet when
it dereferenced unitialized list heads:
http://bugzilla.kernel.org/show_bug.cgi?id=15077
The fix is to add checks in the tx soft IRQ and in the tasklet to
determine which of these two is the last referrer to the transaction
object. Then handle the cleanup of the object by the last referrer
rather than assuming that the tasklet is always the last one.
There is another similar race: Between said tasklet and fwnet_close,
i.e. at ifdown. However, that race is much less likely to occur in
practice and shall be fixed in a separate update.
Reported-by: Илья Басин <basinilya@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The previous changeset left behind an unused inode variable.
This patch removes it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As the padlock driver for SHA uses a software fallback to perform
partial hashing, it must implement custom import/export functions.
Otherwise hmac which depends on import/export for prehashing will
not work with padlock-sha.
Reported-by: Wolfgang Walter <wolfgang.walter@stwm.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
No other driver does anything remotely like this that I know of except
for the tty drivers, and I can't see any reason for random/urandom to do
it. In fact, it's a (trivial, harmless) timing information leak. And
obviously, it generates power- and flash-cycle wasting I/O, especially
if combined with something like hwrngd. Also, it breaks ubifs's
expectations.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: Fix oops after radeon_cs_parser_init() failure.
drm/radeon/kms: move radeon KMS on/off switch out of staging.
drm/radeon/kms: Bailout of blit if error happen & protect with mutex V3
drm/vmwgfx: Don't send bad flags to the host
drm/vmwgfx: Request SVGA version 2 and bail if not found
drm/vmwgfx: Correctly detect 3D
drm/ttm: remove unnecessary save_flags and ttm_flag_masked in ttm_bo_util.c
drm/kms: Remove incorrect comment in struct drm_mode_modeinfo
drm/ttm: remove padding from ttm_ref_object on 64bit builds
drm/radeon/kms: release agp on error.
drm/kms/radeon/agp: Move the check of the aper_size after drm_acp_acquire and drm_agp_info
drm/kms/radeon/agp: Fix warning, format ‘%d’ expects type ‘int’, but argument 4 has type ‘size_t’
drm/ttm: Avoid conflicting reserve_memtype during ttm_tt_set_page_caching.
drm/kms/radeon: pick digitial encoders smarter. (v3)
drm/radeon/kms: use active device to pick connector for encoder
drm/radeon/kms: fix incorrect logic in DP vs eDP connector checking.
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/agp: Fix agp_amd64_init regression
x86: Add quirk for Intel DG45FC board to avoid low memory corruption
x86: Add Dell OptiPlex 760 reboot quirk
x86, UV: Fix RTC latency bug by reading replicated cachelines
oprofile/x86: add Xeon 7500 series support
oprofile/x86: fix crash when profiling more than 28 events
lib/dma-debug.c: mark file-local struct symbol static.
x86/amd-iommu: Fix deassignment of a device from the pt_domain
x86/amd-iommu: Fix IOMMU-API initialization for iommu=pt
x86/amd-iommu: Fix NULL pointer dereference in __detach_device()
x86/amd-iommu: Fix possible integer overflow
The WM8350 LED driver needs to be able to enable and disable the
regulators it is using. Previously the core wasn't properly enforcing
status change constraints so the driver was able to function but this
has always been intended to be required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If radeon_cs_parser_init() fails, radeon_cs_ioctl() calls
radeon_cs_parser_fini() with the non-zero error value. The latter dereferenced
parser->ib which hasn't been initialized yet -> boom. Add a test for parser->ib
being non-NULL before dereferencing it.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Callers (acpi_memhotplug.c, dock.c and others) check for the return
value of acpi_bus_add() and assume a valid device was returned in
case zero was returned.
Thus return -ENODEV if no device was found in acpi_bus_scan and
propagate this through acpi_bus_add and acpi_bus_start.
Also remove a confusing comment in acpiphp_glue.c, acpi_bus_scan
will and cannot invoke if acpi_bus_add returns no valid device.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If acpi_bus_add does not return a device and it's passed
to acpi_bus_start, bad things will happen:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffff8128402d>] acpi_bus_start+0x14/0x24
...
[<ffffffffa008977a>] acpiphp_bus_add+0xba/0x130 [acpiphp]
[<ffffffffa008aa72>] enable_device+0x132/0x2ff [acpiphp]
[<ffffffffa0089b68>] acpiphp_enable_slot+0xb8/0x130 [acpiphp]
[<ffffffffa0089df7>] handle_hotplug_event_func+0x87/0x190 [acpiphp]
Next patch would make this NULL pointer check obsolete, but
better having one more than one missing...
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: stable@kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
We are happy enough that the KMS driver is stable enough for enough people
for the kms enable/disable to leave staging. Distros can now contemplate
turning this on.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If an error happen in r600_blit_prepare_copy report it rather
than WARNING and keeping execution. For instance if ib allocation
failed we did just warn about but then latter tried to access
NULL ib ptr causing oops. This patch also protect r600_copy_blit
with a mutex as otherwise one process might overwrite blit temporary
data with new one possibly leading to GPU lockup.
Should partialy or totaly fix:
https://bugzilla.redhat.com/show_bug.cgi?id=553279
V2 failing blit initialization is not fatal, fallback to memcpy when
this happen
V3 init blit before startup as we pin in startup, remove duplicate
code (this one was actualy tested unlike V2)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes the driver not loading on older versions of VMware.
Signed-off-by: Peter Hanzel <hanzelpeter@gmail.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Re-order structure ttm_ref_object to remove 8 bytes of alignment padding
on 64 bit builds, so shrinking its size from 72 to 64 bytes allowing it
to fit into a smaller slab.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
First call drm_agp_acquire to check if agp has been acquired.
Second call drm_agp_info to fill in the info data struct, including aper_size.
Finally do the check to see if the aper_size makes sense.
Signed-off-by: John Kacur <jkacur@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Fix warning by using %zu instead of %d for size_t
- Fix spelling mistake, "to" should be "too".
Signed-off-by: John Kacur <jkacur@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes errors like:
> reserve_ram_pages_type failed 0x15b7a000-0x15b7b000, track 0x8, req 0x10
when a BO is moved between WC and UC areas.
Reported-by: Xavier Chantry <shiningxc@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
booting a Lenovo W500 with LVDS + DP outputs showed up a TODO we had
on our list, to pick a correct digital encoder block. The LVTMA
encoder requires the second digital encoder, all others can use any
encoder at all.
This fixes the digital encoder selection logic to enable LVDS/DP combos
to work okay.
V2: fix silly addition of connector dig_block and cleanup the other
places in the code that pick the encoder.
V3: rename to dig_encoder and clean up further - also fix
the picking algorithm.
tested on Lenovo W500 + desktop 3650 cards.
Signed-off-by: Dave Airlie <airlied@redhat.com>
On the W500 we have UNIPHY routed to both DVI and DP, this seems
to always pick the DVI connector which means link training fails.
Switch to using active device to pick the connector, this seems
like it should be safe from a code review, and it fixes things
a bit more here.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes the regression introduced by commit
42590a7501 ("x86/agp: Fix
agp_amd64_init and agp_amd64_cleanup").
The above commit changes agp_amd64_init() not to do anything if
gart_iommu_aperture is not zero.
If GART iommu calls agp_amd64_init(), we need to skip
agp_amd64_init() when it's called later via module_init.
The problem is that gart_iommu_init() calls agp_amd64_init()
with not zero gart_iommu_aperture so agp_amd64_init() is never
initialized.
When gart_iommu_init() calls agp_amd64_init(), agp should be
always initialized.
Reported-by: Marin Mitov <mitov@issp.bas.bg>
Reported-by: Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Marin Mitov <mitov@issp.bas.bg>
Tested-by: Kevin Winchester <kjwinchester@gmail.com>
Cc: davej@redhat.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20100125141006O.fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit ac019360fe changed the irq handler logic to BUG_ON rather than
returning IRQ_NONE when the incoming argument is invalid. While this
works in most cases, it doesn't work when the IRQ is shared with other
devices (or when DEBUG_SHIRQ is enabled).
So revert the previous change and replace the warning message with a
comment explaining that we want this behavior.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for page flipping on Ironlake, which uses
different interrupt bits for triggering flip submit IRQs.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: hand-resolved for rebasing off of render power saving patch]
Signed-off-by: Eric Anholt <eric@anholt.net>
Zhenyu noticed that the ironlake vblank enabling patch has one
issue that it will trigger vblank starting from irq postinstall,
this isn't necessary. This patch addresses this issue by only
adding the vblank into DEIER but mask them in DEIMR, so that it
won't trigger vblank interrupt at irq install.
Signed-off-by: Li Peng <peng.li@intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
An earlier commit removed the lock_kernel/unlock_kernel pair but forgot
to remove the unlock_kernel call in the cleanup path at the end of the
function.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
asic3 also needs tmio_core or otherwise will fail to build.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Don't unconditionally dereference the WM97xx core platform data since
it may not be present, causing an oops.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
For pressure-based multi-touch devices, a direct way to send sensor
intensity data per finger is needed. This patch adds the ABS_MT_PRESSURE
event to the MT protocol.
Requested-by: Yoonyoung Shim <jy0922.shim@samsung.com>
Requested-by: Mika Kuoppala <mika.kuoppala@nokia.com>
Requested-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
I missed converting one dev_info call to deb_dbg before submitting the driver.
Without this change, a message will be printed to dmesg for each button press
if a RC6 remote is used.
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: stable <stable@kernel.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We are missing these when building the pci_dev from scratch off
the Open Firmware device-tree
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 37e8273cd3 ("usbnet: Set link down
initially for drivers that update link state") changed the initial link
state in cdc_ether and other drivers based on the understanding that the
devices they support generate link change interrupts. However, this is
optional in the CDC Ethernet protocol, and two users have reported in
<http://bugzilla.kernel.org/show_bug.cgi?id=14791> that the link state
for their devices remains down. Therefore, revert the change in
cdc_ether.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Avi Rozen <avi.rozen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
Fix failure exit in ipathfs
fix oops in fs/9p late mount failure
fix leak in romfs_fill_super()
get rid of pointless checks after simple_pin_fs()
Fix failure exits in bfs_fill_super()
fix affs parse_options()
Fix remount races with symlink handling in affs
Fix a leak in affs_fill_super()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI: remove IOH range fetching
PCI: fix nested spinlock hang in aer_inject
The convention for API functions in kernel is to return errno value;
bond_open would return -1 if alb setup failed. The only reason that
could happen is if kmalloc() failed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call ixgbe_copy_dcb_cfg() earlier in the ixgbe_dcbnl_set_all() so that
we can learn if this is going to fail as early as possible. Previously,
ixgbe_down or ixgbe_close were being called before this check and the
IXGBE_RESETTING bit was being set and cleared. Worse if this failed
the corresponding ixgbe_up/ndo_open would not called.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the correct bit BIT_PG_TX when tx PG settings are set.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change fixes an issue in igbvf with mapped_as_page being left set
after a page is unmapped which results in buffers which are mapped via map
single being unmapped as page.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hello David Miller,
I fix a bug in ks8851_mll driver, which has existed since 2.6.32-rc6.
>From : David J. Choi <david.choi@micrel.com>
Fix a bug that the data pointers in the interrupt handler are set wrong, which is related with the 5th parameter of request_irq().
Signed-off-by : David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug fix in be2net for newer generation of BladeEngine ASIC.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many many ways one can capitalize "Lifebook B Series"...
Signed-off-by: Jon Dodgson <crayzeejon@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] aic79xx: check for non-NULL scb in ahd_handle_nonpkt_busfree
[SCSI] zfcp: Set hardware timeout as requested by BSG request.
[SCSI] zfcp: Introduce bsg_timeout callback.
[SCSI] scsi_transport_fc: Allow LLD to reset FC BSG timeout
[SCSI] zfcp: add missing compat ptr conversion
[SCSI] zfcp: Fix linebreak in hba trace
[SCSI] zfcp: Issue zfcp_fc_wka_port_put after FC CT BSG request
[SCSI] qla2xxx: Update version number to 8.03.01-k10.
[SCSI] fc-transport: Use packed modifier for fc_bsg_request structure.
[SCSI] qla2xxx: Perform fast mailbox read of flash regardless of size nor address alignment.
[SCSI] qla2xxx: Correct FCP2 recovery handling.
[SCSI] scsi_lib: Fix bug in completion of bidi commands
[SCSI] mptsas: Fix issue with chain pools allocation on katmai
[SCSI] aacraid: fix File System going into read-only mode
[SCSI] lpfc: fix file permissions
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] fix single stepped svcs with TRACE_IRQFLAGS=y
[S390] zcrypt: Do not remove coprocessor for error 8/72
[S390] sclp_vt220: set initial terminal window size
[S390] use set_current_state in sigsuspend
[S390] irqflags: add missing types.h include
[S390] dasd: fix possible NULL pointer errors
Having missed the ENOMEM return via i915_gem_fault(), there are probably
other paths that I also missed. By not enabling NORETRY by default these
paths can run the shrinker and take memory from the system (but not from
our own inactive lists because our shrinker can not run whilst we hold
the struct mutex) and this may allow the system to survive a little longer
whilst our drivers consume all available memory.
References:
OOM killer unexpectedly called with kernel 2.6.32
http://bugzilla.kernel.org/show_bug.cgi?id=14933
v2: Pass gfp into page mapping.
v3: Use new read_cache_page_gfp() instead of open-coding.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unsurprisingly, Texas Instruments TSB43AB23 exhibits the same behaviour
as TSB43AB22/A in dual buffer IR DMA mode: If descriptors are located
at physical addresses above the 31 bit address range (2 GB), the
controller will overwrite random memory. With luck, this merely
prevents video reception. With only a little less luck, the machine
crashes.
We use the same workaround here as with TSB43AB22/A: Switch off the
dual buffer capability flag and use packet-per-buffer IR DMA instead.
Another possible workaround would be to limit the coherent DMA mask to
31 bits.
In Linux 2.6.33, this change serves effectively only as documentation
since dual buffer mode is not used for any controller anymore. But
somebody might want to re-enable it in the future to make use of
features of dual buffer DMA that are not available in packet-per-buffer
mode.
In Linux 2.6.32 and older, this update is vital for anyone with this
controller, more than 2 GB RAM, a 64 bit kernel, and FireWire video or
audio applications.
We have at least four reports:
http://bugzilla.kernel.org/show_bug.cgi?id=13808http://marc.info/?l=linux1394-user&m=126154279004083https://bugzilla.redhat.com/show_bug.cgi?id=552142http://marc.info/?l=linux1394-user&m=126432246128386
Reported-by: Paul Johnson
Reported-by: Ronneil Camara
Reported-by: G Zornetzer
Reported-by: Mark Thompson
Cc: stable@kernel.org
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
For SGI UV node controllers (HUB) rev 2.0 or greater, use
replicated cachelines to read the RTC timer. This optimization
allows faster simulataneous reads from a given socket.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20100122154140.GB4975@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Do not use an unchecked variable UBI_IOCMKVOL ioctl.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@vger.kernel.org
In a case where the number of the input data is bigger than the
modulus of the key, the coprocessor adapters will report an 8/72
error. This case is not caught yet, thus the adapter will be taken
offline. To prevent this, we return an -EINVAL instead.
Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When opening a SCLP VT220 terminal, the terminal window size is not
initialized (defaults to zero).
Since the SCLP VT220 terminal supports only 80x24, explicitly set
the window size to prevent (n)curses applications from guessing
the default setting.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix possible NULL pointer in DASD messages and correct discipline
checking.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
netdev_open() will return without cleaning up net device or hardware state
if firmware loading fails. This results in a BUG() on a second attempt to
bring the interface up, reported in
<http://bugzilla.kernel.org/show_bug.cgi?id=15091>, and probably has even
worse effects if the driver is removed afterwards.
Call netdev_close() to clean up on failure.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=15091
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Reported-by: Michael Moffatt <michael@moffatt.org.nz>
Tested-by: Michael Moffatt <michael@moffatt.org.nz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit db5d247a "firewire: fix use of multiple AV/C devices, allow
multiple FCP listeners" introduced a regression into 2.6.33-rc3:
The core freed payloads of incoming requests to FCP_Request or
FCP_Response before a userspace driver accessed them.
We need to copy such payloads for each registered userspace client
and free the copies according to the lifetime rules of non-FCP client
request resources.
(This could possibly be optimized by reference counts instead of
copies.)
The presently only kernelspace driver which listens for FCP requests,
firedtv, was not affected because it already copies FCP frames into an
own buffer before returning to firewire-core's FCP handler dispatcher.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Presently, firewire-core only checks whether descriptors that are to be
added by userspace drivers to the local node's config ROM do not exceed
a size of 256 quadlets. However, the sum of the bare minimum ROM plus
all descriptors (from firewire-core, from firewire-net, from userspace)
must not exceed 256 quadlets.
Otherwise, the bounds of a statically allocated buffer will be
overwritten. If the kernel survives that, firewire-core will
subsequently be unable to parse the local node's config ROM.
(Note, userspace drivers can add descriptors only through device files
of local nodes. These are usually only accessible by root, unlike
device files of remote nodes which may be accessible to lesser
privileged users.)
Therefore add a test which takes the actual present and required ROM
size into account for all descriptors of kernelspace and userspace
drivers.
Cc: stable@kernel.org
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The first page flip queued will replace the current front buffer, which
should have a 0 pending flip count. So at finish time we need to handle
that case (i.e. if the flip count is 0 *or* dec_and_test is 0 we need to
wake the waiters).
Also fix up an error path in the queue function and add some debug
output (only enabled with driver debugging).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: fix memory leak in update path
UBI: add more checks to chdev open
UBI: initialise update marker
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (fschmd) Fix a memleak on multiple opens of /dev/watchdog
hwmon: (asus_atk0110) Do not fail if MBIF is missing
hwmon: (amc6821) Double unlock bug
hwmon: (smsc47m1) Fix section mismatch
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (95 commits)
drm/radeon/kms: preface warning printk with driver name
drm/radeon/kms: drop unnecessary printks.
drm: fix regression in fb blank handling
drm/radeon/kms: make hibernate work on IGPs
drm/vmwgfx: Optimize memory footprint for DMA buffers.
drm/ttm: Allow system memory as a busy placement.
drm/ttm: Fix race condition in ttm_bo_delayed_delete (v3, final)
drm/nv50: prevent switching off SOR when in use for DVI-over-DP
drm/nv50: fail auxch transaction if reply count not what we expect
drm/nouveau: fix failure path if userspace specifies no valid memtypes
drm/nouveau: report LVDS as disconnected if lid closed
drm/radeon/kms: fix legacy get_engine/memory clock
drm/radeon/kms/atom: atom parser fixes
drm/radeon/kms: clean up atombios pll code
drm/radeon/kms: clean up pll struct
drm/radeon/kms/atom: fix crtc lock ordering
drm/radeon: r6xx/r7xx possible security issue, system ram access
drm/radeon/kms: r600/r700 don't test ib if ib initialization fails
drm/radeon/kms: Forbid creation of framebuffer with no valid GEM object
drm/radeon/kms: r600 handle irq vector ring overflow
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
virtio_net: Make delayed refill more reliable
sfc: Use fixed-size buffers for MCDI NVRAM requests
sfc: Add workspace for GMAC bug workaround to MCDI MAC_STATS buffer
tcp_probe: avoid modulus operation and wrap fix
qlge: Only free resources if they were allocated
netns xfrm: deal with dst entries in netns
sky2: revert config space change
vlan: fix vlan_skb_recv()
netns xfrm: fix "ip xfrm state|policy count" misreport
sky2: Enable/disable WOL per hardware device
net: Fix IPv6 GSO type checks in Intel ethernet drivers
igb/igbvf: cleanup exception handling in tx_map_adv
MAINTAINERS: Add Intel igbvf maintainer
e1000/e1000e: don't use small hardware rx buffers
fmvj18x_cs: add new id (Panasonic lan & modem card)
be2net: swap only first 2 fields of mcc_wrb
Please add support for Microsoft MN-120 PCMCIA network card
be2net: fix bug in rx page posting
wimax/i2400m: Add support for more i6x50 SKUs
e1000e: enhance frame fragment detection
...
This patch adds a new USB HID driver for the Ortek WKB-2000, working around an
incorrect LogicalMaximum value in the USB resource descriptor.
Tracked by http://bugzilla.kernel.org/show_bug.cgi?id=14787
Bug originally reported by Ubuntu users: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/405390
Signed-off-by: Johnathon Harris <jmharris@gmail.com>
Tested-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I have seen RX stalls on a machine that experienced a suspected
OOM. After the stall, the RX buffer is empty on the guest side
and there are exactly 16 entries available on the host side. As
the number of entries is less than that required by a maximal
skb, the host cannot proceed.
The guest did not have a refill job scheduled.
My diagnosis is that an OOM had occured, with the delayed refill
job scheduled. The job was able to allocate at least one skb, but
not enough to overcome the minimum required by the host to proceed.
As the refill job would only reschedule itself if it failed completely
to allocate any skbs, this would lead to an RX stall.
The following patch removes this stall possibility by always
rescheduling the refill job until the ring is totally refilled.
Testing has shown that the RX stall no longer occurs whereas
previously it would occur within a day.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The low-level MCDI code always uses 32-bit MMIO operations, and
callers must pad input and output buffers to multiples of 4 bytes.
The MCDI NVRAM functions are not doing this. Also, their buffers are
declared as variable-length arrays with no explicit maximum length.
Switch to a fixed buffer size based on the chunk size used by the
MTD driver (which is a multiple of 4).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a hardware bug in the SFC9000 family, the firmware must
transfer raw GMAC statistics to host memory before aggregating them
into the cooked (speed-independent) MAC statistics. Extend the stats
buffer to support this.
The length of the buffer is explicit in the MAC_STATS command, so this
change is backward-compatible on both sides.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently qlge tries to release regions even if they were not allocated.
This causes messages like the following in the kernel log
Trying to free nonexistent resource <00000000006af400-00000000006af4ff>
Trying to free nonexistent resource <00003c04ff9f4000-00003c04ff9f7fff>
Trying to free nonexistent resource <00003c04ffc00000-00003c04ffcfffff>
This patch fixes the goto logic in order to not release the resources
if they were not allocated.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Among other changes, this commit:
commit 06d0f0663e
Author: Sujith <Sujith.Manoharan@atheros.com>
Date: Thu Feb 12 10:06:45 2009 +0530
ath9k: Enable Fractional N mode
changed the hw attach code to fix up initialization values only for
dual band devices, however the commit message did not give a reason as
to why this would be useful or necessary.
According to tests by Jorge Boncompte, this breaks at least some
2GHz-only cards, so the code should be changed back to the
unconditional INI fixup.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Jorge Boncompte <jorge@dti2.net>
Cc: stable@kernel.org
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are a few station addresses that are
char *, instead of the normal u8 *; gcc
gives pointer signedness warnings for some
of those, so use u8 * consistently.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mdelay function was used between I/O access commands, that causes peak
in CPU usage. Fix it by substitution mdelay to msleep.
Expand usage on fitPC2 compatible boards according to DMI identification.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The aer_inject module hangs in aer_inject() when checking the device's
error masks. The hang is due to a recursive use of the aer_inject lock.
The aer_inject() routine grabs the lock while processing the error and then
calls pci_read_config_dword to read the masks. The pci_read_config_dword
routine is earlier overridden by pci_read_aer, which among other things,
grabs the aer_inject lock.
Fixed by moving the pci_read_config_dword calls to read the masks to before
the lock is taken.
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Pineview doesn't has CXSR and need GTT-based hardware status page.
It fixes a X boot hung issue on Pinview since commit cfdf1f
Signed-off-by: Li Peng <peng.li@intel.com>
Acked-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
so far vblank interrupt on ironlake is disabled, this would cause
bad gfx performance if userspace calls drm_wait_vblank. This patch
enables vblank interrupt on ironlake and follows vblank get/put
model.
Signed-off-by: Li Peng <peng.li@intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This tries to fix CRT detect loop hang seen on some Ironlake form
factor, to clear up hotplug detect state before taking CRT detect
to make sure next hotplug detect cycle is consistent.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
When /dev/watchdog gets opened a second time we return -EBUSY, but
we already have got a kref then, so we end up leaking our data struct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
MBIF (motherboard identification) is only used to print the name of
the board, it's not essential for the driver; do not fail if it's
missing. Based on Juan's patch.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Acked-by: Juan RP <xtraeme@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
smsc47m1_restore is called from sm_smsc47m1_exit, which is an __exit
function, so it can't be __init.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Obviously, this register had some other impact that is causing
the regression. Either it is masking some other access or needs
to be reset in some path.
Either, way it is best to just revert the change for 2.6.33
This reverts commit 166a0fd4c7.
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcel Selhorst
Borislav Petkov
Michael Poole
Andy Getzendanner
Dave Airlie
Pauli Nieminen
Thomas Hellstrom
Jakob Bornecrantz
Jesse Barnes
Rafael J. Wysocki
Matthew Garrett
Marcin Slusarz
Owain Ainsworth
Zhenyu Wang
Chris Wilson
Daniel Vetter
David S. Miller
Sean Hefty
Julia Lawall
Guennadi Liakhovetski
Simon Kagstrom
Jelle Martijn Kok
Linus Torvalds
Jiri Kosina
Stephane Chatty
Stephane Chatty
NeilBrown
Maarten Maathuis
Ben Skeggs
Roel Kluin
Sujith
Bastien Nocera
Leo P White
Jan Glauber
Ursula Braun
Divy Le Ray
Marcin Kościelnicki
Luca Barbieri
Francisco Jerez
Wey-Yi Guy
Anirban Chakraborty
Xiaotian Feng
Swen Schillig
Kashyap, Desai
Francesco Lavra
Mauro Carvalho Chehab
Dmitry Torokhov
Yong Zhang
Jean Delvare
Ray Copeland
Andres Salomon
Stephen M. Cameron
Rafał Miłecki
Paul Mundt
Dave Airlie
Jerome Glisse
Andrew Morton
Randy Dunlap
Thadeu Lima de Souza Cascardo
Alexander Duyck
Thomas Meyer
David John
FUJITA Tomonori
Catalin Marinas
Tejun Heo
Douglas Gilbert
Krishna Kumar
Anton Blanchard
Amit Kumar Salecha
Yoichi Yuasa
stephen hemminger
Michael Buesch
Larry Finger
Alex Neblett
Dan Williams
Richard Röjfors
Uwe Kleine-König
Wu Fengguang
KAMEZAWA Hiroyuki
Sergey Matyukevich
Alberto Panizzo
Evgeniy Polyakov
Anatolij Gustschin
Alexander Shishkin
Sathya Perla
Magnus Damm
Markus Pietrek
Stefan Richter
Herbert Xu
Matt Mackall
Mark Brown
Michel Dänzer
Thomas Renninger
Peter Hanzel
Austin Yuan
Richard Kennedy
John Kacur
Dave Airlie
Vikram Kandukuri
Mike Frysinger
Zhao Yakui
Li Peng
Hans Verkuil
Dmitry Artamonow
Henrik Rydberg
David Härdeman
Benjamin Herrenschmidt
Ben Hutchings
John Fastabend
Choi, David
Ajit Khaparde
Jon Dodgson
Dimitri Sivanich
Mika Westerberg
Felix Beck
Hendrik Brueckner
Stefan Haberland
Ben Hutchings
Al Viro
Johnathon Harris
Guido Barzini
Breno Leitao
Jens Axboe
Felix Fietkau
Johannes Berg
Denis Turischev
Andrew Patterson
Dan Carpenter
Hans de Goede
Luca Tettamanti
Jeff Mahoney