Usually harmless, since the scatterlist is always hard-coded to a length
of 1, but it triggers a BUG() if CONFIG_DEBUG_SG=y, so we better fix it.
This fixes <http://bugzilla.kernel.org/show_bug.cgi?id=9934>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch acts as a preparation for using checksum offload for IB
devices capable of inserting/verifying checksum in IP packets. The
patch does not actaully turn on NETIF_F_SG - we defer that to the
patches adding checksum offload capabilities.
We only add support for send gathers for datagram mode, since existing
HW does not support checksum offload on connected QPs.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
All current InfiniBand devices can handle all DMA addresses, and it's
hard to imagine anyone would be silly enough to build a new device
that couldn't. Therefore, enable the NETIF_F_HIGHDMA feature for IPoIB.
This has no effect for no, but is needed when we enable gather/scatter
support and checksum stateless offloads.
Signed-off-by: Eli Cohen <eli@mellnaox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX HCA supports shrinking WQEs, so that a single work request
can be made of multiple units of wqe_shift. This way, WRs can differ
in size, and do not have to be a power of 2 in size, saving memory and
speeding up send WR posting. Unfortunately, if we do this then the
wqe_index field in CQEs can't be used to look up the WR ID anymore, so
our implementation does this only if selective signaling is off.
Further, on 32-bit platforms, we can't use vmap() to make the QP
buffer virtually contigious. Thus we have to use constant-sized WRs to
make sure a WR is always fully within a single page-sized chunk.
Finally, we use WRs with the NOP opcode to avoid wrapping around the
queue buffer in the middle of posting a WR, and we set the
NoErrorCompletion bit to avoid getting completions with error for NOP
WRs. However, NEC is only supported starting with firmware 2.2.232,
so we use constant-sized WRs for older firmware. And, since MLX QPs
only support SEND, we use constant-sized WRs in this case.
When stamping during NOP posting, do stamping following setting of the
NOP WQE valid bit.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We use struct mlx4_buf for kernel QP, CQ and SRQ buffers, and the code
to look up an entry is duplicated in get_cqe_from_buf() and the QP and
SRQ versions of get_wqe(). Factor this out into mlx4_buf_offset().
This will also make it easier to switch over to using vmap() for buffers.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a standard NIC and RDMA/iWARP driver for NetEffect 1/10Gb ethernet adapters.
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the allocation of the MTT or the mailbox failed, mthca_fmr_alloc()
would return 0 (success) no matter what. This leads to crashes a
little down the road, when we try to dereference eg mr->mtt, which was
really ERR_PTR(-Ewhatever).
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The string mlx4_ib_version was defined, but never used. Print out the
version once when the first device is initialized.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We have recently discovered that Tavor mode requires each WQE in a
posted list of receive WQEs to have a valid NDA field at all times.
This requirement holds true for regular QPs as well as for SRQs. This
patch prelinks the receive queue in a regular QP and keeps the free
list in SRQ always properly linked.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The SRQ receive posting functions make sure that srq->first_free never
becomes negative, so we can remove tests of whether it is negative.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Allocate memory for the page_list field of struct ib_pool_fmr only
when caching is enabled for the FMR pool, since the field is not used
otherwise. This can save significant amounts of memory for large
pools with caching turned off.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a host just goes away (crash, power loss, etc.) without tearing
down its IB connections, it can get stale connection errors when it
tries to reconnect to targets upon rebooting. Retrying the connection
a few times will prevent sysadmins from playing the "which disk(s)
went missing?" game.
This would have made things slightly quicker when tracking down some
of the recent bugs, but it also helps quite a bit when you've got a
large number of targets hanging off a wedged server.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The firmware QUERY_ADAPTER command does not return vendor_id,
device_id, and revision_id; eliminate these fields from the query.
Initialize the rev_id field of the mlx4 device via init_node_data (MAD
IFC query), as is done in the query_device verb implementation.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For memfree devices, the firmware QUERY_ADAPTER command does not
return vendor_id, device_id, and revision_id; do not return these
fields in the QUERY_ADAPTER function for memfree devices.
Instead, for memfree devices, initialize the rev_id field of the mthca
device via init_node_data (MAD IFC query), as is done in the
query_device verb implementation.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 732a2170 ("IB/ipoib: Bound the net device to the ipoib_neigh
structue") left a misleading debug print (n->dev would be a bond
device only if boding is used). Clean it up.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move up the code that checks for a situation where the remote GID
stored in the ipoib_neigh is different than the one present in the
neighbour (handle gratuitous ARP) or that a bonding fail over has
happened but the neighbour still has a pointer to an ipoib_neigh
created by a different device than the current slave. This will cause
the driver to apply the check also for connected mode neighbours.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In mthca_reg_phys_mr(), we calculate the page size for the HCA
hardware to use to map the buffer list passed in by the consumer.
For example, if the consumer passes in
[0] addr 0x1000, size 0x1000
[1] addr 0x2000, size 0x1000
then the algorithm would come up with a page size of 0x2000 and a list
of two pages, at 0x0000 and 0x2000. Usually, this would work fine
since the memory region would start at an offset of 0x1000 and have a
length of 0x2000.
However, the old code did not take into account the alignment of the
IO virtual address passed in. For example, if the consumer passed in
a virtual address of 0x6000 for the above, then the offset of 0x1000
would not be used correctly because the page mask of 0x1fff would
result in an offset of 0.
We can fix this quite neatly by making sure that the page shift we use
is no bigger than the first bit where the start of the first buffer
and the IO virtual address differ. Also, we can further simplify the
code by removing the special case for a single buffer by noticing that
it doesn't matter if we use a page size that is too big. This allows
the loop to compute the page shift to be replaced with __ffs().
Thanks to Bryan S Rosenburg <rosnbrg@us.ibm.com> for pointing out the
original bug and suggesting several ways to improve this patch.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch enables ehca to redirect any PMA queries to the
actual PMA QP.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Reviewed-by: Joachim Fenkes <fenkes@de.ibm.com>
Reviewed-by: Christoph Raisch <raisch@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IB spec doesn't allow packets to QP0 sent on any other VL than VL15.
Hardware doesn't filter those packets on the send side, so we need to do
this in the driver and firmware.
As eHCA doesn't support QP0, we can just filter out all traffic going to
QP0, regardless of SL or VL.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Paths with hop_limit > 1 indicate that the connection will be routed
between IB subnets. Update the subnet local field in the CM REQ based
on the hop_limit value. In addition, if the path is routed, then set
the LIDs in the REQ to the permissive LIDs. This is used to indicate
to the passive side that it should use the LIDs in the received local
route header (LRH) associated with the REQ when programming the QP.
This is a temporary work-around to the IB CM to support IB router
development until the IB router specification is completed. It is not
anticipated that this work-around will cause any interoperability
issues with existing stacks or future stacks that will properly
support IB routers when defined.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With the sg table code, every SCSI driver is now either chain capable
or broken (or has sg_tablesize set so chaining is never activated), so
there's no need to have a check in the host template.
Also tidy up the code by moving the scatterlist size defines into the
SCSI includes and permit the last entry of the scatterlist pools not
to be a power of two.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.25: (1470 commits)
[IPV6] ADDRLABEL: Fix double free on label deletion.
[PPP]: Sparse warning fixes.
[IPV4] fib_trie: remove unneeded NULL check
[IPV4] fib_trie: More whitespace cleanup.
[NET_SCHED]: Use nla_policy for attribute validation in ematches
[NET_SCHED]: Use nla_policy for attribute validation in actions
[NET_SCHED]: Use nla_policy for attribute validation in classifiers
[NET_SCHED]: Use nla_policy for attribute validation in packet schedulers
[NET_SCHED]: sch_api: introduce constant for rate table size
[NET_SCHED]: Use typeful attribute parsing helpers
[NET_SCHED]: Use typeful attribute construction helpers
[NET_SCHED]: Use NLA_PUT_STRING for string dumping
[NET_SCHED]: Use nla_nest_start/nla_nest_end
[NET_SCHED]: Propagate nla_parse return value
[NET_SCHED]: act_api: use PTR_ERR in tcf_action_init/tcf_action_get
[NET_SCHED]: act_api: use nlmsg_parse
[NET_SCHED]: act_api: fix netlink API conversion bug
[NET_SCHED]: sch_netem: use nla_parse_nested_compat
[NET_SCHED]: sch_atm: fix format string warning
[NETNS]: Add namespace for ICMP replying code.
...
Needed to propagate it down to the ip_route_output_flow.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed to propagate it down to the __ip_route_output_key.
Signed_off_by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
in_dev_find() need a namespace to pass it to fib_get_table(), so add
an argument.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes TOPDIR from infiniband Makefile and delete
one include statement pointing to a non-existing directory
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <mshefty@ichips.intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
Correctly work around T3A issues by checking "hwtype != T3A" instead of
"hwtype == T3B". This will be needed for new hardware types.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The existing logic incorrectly maps this buffer list:
0: addr 0x10001000, size 0x1000
1: addr 0x10002000, size 0x1000
To this bogus page list:
0: 0x10000000
1: 0x10002000
The shift calculation must also take into account the address of the
first entry masked by the page_mask as well as the last address+size
rounded up to the next page size.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- for kernel mode cqs, call event notification handler when flushing.
- flush QP when moving from RTS -> CLOSING.
- fix logic to identify a kernel mode qp.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the increment of s_hdrwords into the existing if block that tests
if we're doing a send with immediate, to save one test of the opcode.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
qdisc_run() now tests for queue_stopped() before calling
__qdisc_run(), and the same check is done in every iteration of
__qdisc_run(), so another check is not required in the driver xmit.
This means that ipoib_start_xmit() no longer needs to test
netif_queue_stopped(); the test was added to fix earlier kernels,
where the networking stack did not guarantee that the xmit method of
an LLTX driver would not be called after the queue was stopped, but
current kernels do provide this guarantee.
To validate, I put a debug in the TX_BUSY path which never hit with 64
threads running overnight exercising this code a few 100 million
times.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add new mappings from port physical state (a HW register value) to the
IB SubnGet(PortInfo) port physical state.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IBA7220 uses a count-based triggering mechanism, and therefore
can't use the same bandwidth verification mechanism as older chips.
To support the 7220, allow enabling and disabling armlaunch errors on
application request. Minor robustness improvements as well.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clean up some unused header fields, minor related cleanup.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IBA7220 includes many more configurable IB settings. Getting/setting
these is now grouped into a pair of chip specific functions accessed via
function pointers. Provide sysfs access to these settings.
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This adds the new (sometimes empty) chip-specific functions to the older
chips, and makes the initialization and related functions consistent across
all 3 chips.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This code has been unused for some time, but still had leftovers
from when it was used.
Signed-off-by: Dave Olson <dave.olson@qlogic.com
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some HW revisions of eHCA2 may cause an RC connection to break if they
received RDMA Reads over that connection before. This can be
prevented by assuring that, after the first RDMA Read, the QP receives
a new RDMA Read every few million link packets.
Include code into the driver that inserts an empty (size 0) RDMA Read
into the message stream every now and then if the consumer doesn't
post them frequently enough.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch enhances ehca with a capability to "autodetect" the ports
being connected physically. In order to utilize that function the
module option nr_ports must be set to -1 (default is 2 - two
ports). This feature is experimental and will made the default later.
More detail:
If the user connects only one port to the switch, current code requires
1) port one to be connected and
2) module option nr_ports=1 to be given.
If autodetect is enabled, ehca will not wait at creation of the GSI QP
for the respective port to become active. Since firmware does not
accept modify_qp() while the port is down at initialization, we need
to cache all calls to modify_qp() for the SMI/GSI QP and just return a
good return code.
When a port is activated and we get a PORT_ACTIVE event, we replay the
cached modify-qp() parms and re-trigger any posted recv WRs. Only then
do we forward the PORT_ACTIVE event to registered clients.
The result of this autodetect patch is that all ports will be
accessible by the users. Depending on their respective cabling only
those ports that are connected properly will become operable. If a
user tries to modify a regular QP of a non-connected port, modify_qp()
will fail. Furthermore, ibv_devinfo should show the port state
accordingly.
Note that this patch primarily improves the loading behaviour of
ehca. If the cable is removed while the driver is operating and
plugged in again, firmware will handle that properly by sending an
appropriate async event.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
