Commit Graph

41 Commits

Author SHA1 Message Date
Brandt, Todd E 3831261eb0 PM / Sleep: increase ftrace coverage in suspend/resume
Change where ftrace is disabled and re-enabled during system
suspend/resume to allow tracing of device driver pm callbacks.
Ftrace will now be turned off when suspend reaches
disable_nonboot_cpus() instead of at the very beginning of system
suspend.

Ftrace was disabled during suspend/resume back in 2008 by
Steven Rostedt as he discovered there was a conflict in the
enable_nonboot_cpus() call (see commit f42ac38 "ftrace: disable
tracing for suspend to ram").  This change preserves his fix by
disabling ftrace, but only at the function where it is known
to cause problems.

The new change allows tracing of the device level code for better
debug.

[rjw: Changelog]
Signed-off-by: Todd Brandt <todd.e.brandt@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-07-26 00:49:07 +02:00
Bernie Thompson 9350de06be PM / wakeup: Adjust messaging for wake events during suspend
This adds in a new message to the wakeup code which adds an
indication to the log that suspend was cancelled due to a wake event
occouring during the suspend sequence. It also adjusts the message
printed in suspend.c to reflect the potential that a suspend was
aborted, as opposed to a device failing to suspend.

Without these message adjustments one can end up with a kernel log
that says that a device failed to suspend with no actual device
suspend failures, which can be confusing to the log examiner.

Signed-off-by: Bernie Thompson <bhthompson@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-06-11 23:53:37 +02:00
Zhang Rui c26b78a2d8 PM / sleep: invalidate TEST_CPUS and TEST_CORE support for freeze state
freeze state is a software suspend state that does not run into
low-level platform callbacks which may interact with BIOS.
And freeze state does not need to disable the processors.

But the current pm_test support misleads users because users
can enter freeze state with pm_test set to TEST_CPUS/TEST_CORE,
while this pm_test setting never takes actions.

So, invalidate TEST_CPUS/TEST_CORE for freeze state in this patch.
Then users will get an error instead, when trying to
enter freeze state with pm_test mode set to TEST_CPUS/TEST_CORE.

Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-04-05 14:18:25 +02:00
Zhang Rui 08605acc7e PM / sleep: add TEST_PLATFORM support for freeze state
Invoke freeze_enter() after suspend_test(TEST_PLATFORM) being invoked.

So when setting /sys/power/pm_test to "platform", it can be used to
check if freeze state is working well after all devices are suspended
and before processors are blocked,

Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-04-05 14:18:25 +02:00
Zhang Rui 7e73c5ae6e PM: Introduce suspend state PM_SUSPEND_FREEZE
PM_SUSPEND_FREEZE state is a general state that
does not need any platform specific support, it equals
frozen processes + suspended devices + idle processors.

Compared with PM_SUSPEND_MEMORY,
PM_SUSPEND_FREEZE saves less power
because the system is still in a running state.
PM_SUSPEND_FREEZE has less resume latency because it does not
touch BIOS, and the processors are in idle state.

Compared with RTPM/idle,
PM_SUSPEND_FREEZE saves more power as
1. the processor has longer sleep time because processes are frozen.
   The deeper c-state the processor supports, more power saving we can get.
2. PM_SUSPEND_FREEZE uses system suspend code path, thus we can get
   more power saving from the devices that does not have good RTPM support.

This state is useful for
1) platforms that do not have STR, or have a broken STR.
2) platforms that have an extremely low power idle state,
   which can be used to replace STR.

The following describes how PM_SUSPEND_FREEZE state works.
1. echo freeze > /sys/power/state
2. the processes are frozen.
3. all the devices are suspended.
4. all the processors are blocked by a wait queue
5. all the processors idles and enters (Deep) c-state.
6. an interrupt fires.
7. a processor is woken up and handles the irq.
8. if it is a general event,
   a) the irq handler runs and quites.
   b) goto step 4.
9. if it is a real wake event, say, power button pressing, keyboard touch, mouse moving,
   a) the irq handler runs and activate the wakeup source
   b) wakeup_source_activate() notifies the wait queue.
   c) system starts resuming from PM_SUSPEND_FREEZE
10. all the devices are resumed.
11. all the processes are unfrozen.
12. system is back to working.

Known Issue:
The wakeup of this new PM_SUSPEND_FREEZE state may behave differently
from the previous suspend state.
Take ACPI platform for example, there are some GPEs that only enabled
when the system is in sleep state, to wake the system backk from S3/S4.
But we are not touching these GPEs during transition to PM_SUSPEND_FREEZE.
This means we may lose some wake event.
But on the other hand, as we do not disable all the Interrupts during
PM_SUSPEND_FREEZE, we may get some extra "wakeup" Interrupts, that are
not available for S3/S4.

The patches has been tested on an old Sony laptop, and here are the results:

Average Power:
1. RPTM/idle for half an hour:
   14.8W, 12.6W, 14.1W, 12.5W, 14.4W, 13.2W, 12.9W
2. Freeze for half an hour:
   11W, 10.4W, 9.4W, 11.3W 10.5W
3. RTPM/idle for three hours:
   11.6W
4. Freeze for three hours:
   10W
5. Suspend to Memory:
   0.5~0.9W

Average Resume Latency:
1. RTPM/idle with a black screen: (From pressing keyboard to screen back)
   Less than 0.2s
2. Freeze: (From pressing power button to screen back)
   2.50s
3. Suspend to Memory: (From pressing power button to screen back)
   4.33s

>From the results, we can see that all the platforms should benefit from
this patch, even if it does not have Low Power S0.

Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-02-09 22:30:44 +01:00
Rafael J. Wysocki 300d3739e8 Revert "NMI watchdog: fix for lockup detector breakage on resume"
Revert commit 45226e9 (NMI watchdog: fix for lockup detector breakage
on resume) which breaks resume from system suspend on my SH7372
Mackerel board (by causing a NULL pointer dereference to happen) and
is generally wrong, because it abuses the CPU hotplug functionality
in a shamelessly blatant way.

The original issue should be addressed through appropriate syscore
resume callback instead.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2012-08-08 20:49:45 +02:00
Sameer Nanda 45226e944c NMI watchdog: fix for lockup detector breakage on resume
On the suspend/resume path the boot CPU does not go though an
offline->online transition.  This breaks the NMI detector post-resume
since it depends on PMU state that is lost when the system gets
suspended.

Fix this by forcing a CPU offline->online transition for the lockup
detector on the boot CPU during resume.

To provide more context, we enable NMI watchdog on Chrome OS.  We have
seen several reports of systems freezing up completely which indicated
that the NMI watchdog was not firing for some reason.

Debugging further, we found a simple way of repro'ing system freezes --
issuing the command 'tasket 1 sh -c "echo nmilockup > /proc/breakme"'
after the system has been suspended/resumed one or more times.

With this patch in place, the system freeze result in panics, as
expected.

These panics provide a nice stack trace for us to debug the actual issue
causing the freeze.

[akpm@linux-foundation.org: fiddle with code comment]
[akpm@linux-foundation.org: make lockup_detector_bootcpu_resume() conditional on CONFIG_SUSPEND]
[akpm@linux-foundation.org: fix section errors]
Signed-off-by: Sameer Nanda <snanda@chromium.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Mandeep Singh Baines <msb@chromium.org>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-07-30 17:25:13 -07:00
Srivatsa S. Bhat 443772d408 ftrace: Disable function tracing during suspend/resume and hibernation, again
If function tracing is enabled for some of the low-level suspend/resume
functions, it leads to triple fault during resume from suspend, ultimately
ending up in a reboot instead of a resume (or a total refusal to come out
of suspended state, on some machines).

This issue was explained in more detail in commit f42ac38c59 (ftrace:
disable tracing for suspend to ram). However, the changes made by that commit
got reverted by commit cbe2f5a6e8 (tracing: allow tracing of
suspend/resume & hibernation code again). So, unfortunately since things are
not yet robust enough to allow tracing of low-level suspend/resume functions,
suspend/resume is still broken when ftrace is enabled.

So fix this by disabling function tracing during suspend/resume & hibernation.

Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2012-07-01 13:31:22 +02:00
Rafael J. Wysocki 1e73203cd1 PM / Sleep: Move disabling of usermode helpers to the freezer
The core suspend/hibernation code calls usermodehelper_disable() to
avoid race conditions between the freezer and the starting of
usermode helpers and each code path has to do that on its own.
However, it is always called right before freeze_processes()
and usermodehelper_enable() is always called right after
thaw_processes().  For this reason, to avoid code duplication and
to make the connection between usermodehelper_disable() and the
freezer more visible, make freeze_processes() call it and remove the
direct usermodehelper_disable() and usermodehelper_enable() calls
from all suspend/hibernation code paths.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
2012-03-28 23:30:21 +02:00
Rafael J. Wysocki bc25cf5089 PM / Sleep: Drop suspend_stats_update()
Since suspend_stats_update() is only called from pm_suspend(),
move its code directly into that function and remove the static
inline definition from include/linux/suspend.h.  Clean_up
pm_suspend() in the process.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
2012-02-17 23:36:23 +01:00
Rafael J. Wysocki 93e1ee43a7 PM / Sleep: Make enter_state() in kernel/power/suspend.c static
The enter_state() function in kernel/power/suspend.c should be
static and state_store() in kernel/power/suspend.c should call
pm_suspend() instead of it, so make that happen (which also reduces
code duplication related to suspend statistics).

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
2012-02-17 23:36:10 +01:00
Rafael J. Wysocki 55ae451918 PM / Sleep: Unify kerneldoc comments in kernel/power/suspend.c
The kerneldoc comments in kernel/power/suspend.c are not formatted
in the same way and the quality of some of them is questionable.
Unify the formatting and improve the contents.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
2012-02-17 23:36:03 +01:00
Marcos Paulo de Souza 8916e3702e PM / Suspend: Avoid code duplication in suspend statistics update
The code
       if (error) {
               suspend_stats.fail++;
               dpm_save_failed_errno(error);
       } else
               suspend_stats.success++;

Appears in the kernel/power/main.c and kernel/power/suspend.c.

This patch just creates a new function to avoid duplicated code.

Suggested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Marcos Paulo de Souza <marcos.mage@gmail.com>
Acked-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2012-02-09 23:55:43 +01:00
Rafael J. Wysocki cf579dfb82 PM / Sleep: Introduce "late suspend" and "early resume" of devices
The current device suspend/resume phases during system-wide power
transitions appear to be insufficient for some platforms that want
to use the same callback routines for saving device states and
related operations during runtime suspend/resume as well as during
system suspend/resume.  In principle, they could point their
.suspend_noirq() and .resume_noirq() to the same callback routines
as their .runtime_suspend() and .runtime_resume(), respectively,
but at least some of them require device interrupts to be enabled
while the code in those routines is running.

It also makes sense to have device suspend-resume callbacks that will
be executed with runtime PM disabled and with device interrupts
enabled in case someone needs to run some special code in that
context during system-wide power transitions.

Apart from this, .suspend_noirq() and .resume_noirq() were introduced
as a workaround for drivers using shared interrupts and failing to
prevent their interrupt handlers from accessing suspended hardware.
It appears to be better not to use them for other porposes, or we may
have to deal with some serious confusion (which seems to be happening
already).

For the above reasons, introduce new device suspend/resume phases,
"late suspend" and "early resume" (and analogously for hibernation)
whose callback will be executed with runtime PM disabled and with
device interrupts enabled and whose callback pointers generally may
point to runtime suspend/resume routines.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
2012-01-29 20:38:29 +01:00
Srivatsa S. Bhat bcda53faf5 PM / Sleep: Replace mutex_[un]lock(&pm_mutex) with [un]lock_system_sleep()
Using [un]lock_system_sleep() is safer than directly using mutex_[un]lock()
on 'pm_mutex', since the latter could lead to freezing failures. Hence convert
all the present users of mutex_[un]lock(&pm_mutex) to use these safe APIs
instead.

Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2011-12-08 23:22:29 +01:00
Tejun Heo 03afed8bc2 freezer: clean up freeze_processes() failure path
freeze_processes() failure path is rather messy.  Freezing is canceled
for workqueues and tasks which aren't frozen yet but frozen tasks are
left alone and should be thawed by the caller and of course some
callers (xen and kexec) didn't do it.

This patch updates __thaw_task() to handle cancelation correctly and
makes freeze_processes() and freeze_kernel_threads() call
thaw_processes() on failure instead so that the system is fully thawed
on failure.  Unnecessary [suspend_]thaw_processes() calls are removed
from kernel/power/hibernate.c, suspend.c and user.c.

While at it, restructure error checking if clause in suspend_prepare()
to be less weird.

-v2: Srivatsa spotted missing removal of suspend_thaw_processes() in
     suspend_prepare() and error in commit message.  Updated.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
2011-11-21 12:32:24 -08:00
Paul Gortmaker 6e5fdeedca kernel: Fix files explicitly needing EXPORT_SYMBOL infrastructure
These files were getting <linux/module.h> via an implicit non-obvious
path, but we want to crush those out of existence since they cost
time during compiles of processing thousands of lines of headers
for no reason.  Give them the lightweight header that just contains
the EXPORT_SYMBOL infrastructure.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:30:05 -04:00
Paul Gortmaker 74da1ff713 kernel: fix several implicit usasges of kmod.h
These files were implicitly relying on <linux/kmod.h> coming in via
module.h, as without it we get things like:

kernel/power/suspend.c💯 error: implicit declaration of function ‘usermodehelper_disable’
kernel/power/suspend.c:109: error: implicit declaration of function ‘usermodehelper_enable’
kernel/power/user.c:254: error: implicit declaration of function ‘usermodehelper_disable’
kernel/power/user.c:261: error: implicit declaration of function ‘usermodehelper_enable’

kernel/sys.c:317: error: implicit declaration of function ‘usermodehelper_disable’
kernel/sys.c:1816: error: implicit declaration of function ‘call_usermodehelper_setup’
kernel/sys.c:1822: error: implicit declaration of function ‘call_usermodehelper_setfns’
kernel/sys.c:1824: error: implicit declaration of function ‘call_usermodehelper_exec’

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 09:20:12 -04:00
Dan Carpenter 528f7ce6e4 PM / Suspend: Off by one in pm_suspend()
In enter_state() we use "state" as an offset for the pm_states[]
array.  The pm_states[] array only has PM_SUSPEND_MAX elements so
this test is off by one.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
2011-10-16 23:27:46 +02:00
ShuoX Liu 2a77c46de1 PM / Suspend: Add statistics debugfs file for suspend to RAM
Record S3 failure time about each reason and the latest two failed
devices' names in S3 progress.
We can check it through 'suspend_stats' entry in debugfs.

The motivation of the patch:

We are enabling power features on Medfield. Comparing with PC/notebook,
a mobile enters/exits suspend-2-ram (we call it s3 on Medfield) far
more frequently. If it can't enter suspend-2-ram in time, the power
might be used up soon.

We often find sometimes, a device suspend fails. Then, system retries
s3 over and over again. As display is off, testers and developers
don't know what happens.

Some testers and developers complain they don't know if system
tries suspend-2-ram, and what device fails to suspend. They need
such info for a quick check. The patch adds suspend_stats under
debugfs for users to check suspend to RAM statistics quickly.

If not using this patch, we have other methods to get info about
what device fails. One is to turn on  CONFIG_PM_DEBUG, but users
would get too much info and testers need recompile the system.

In addition, dynamic debug is another good tool to dump debug info.
But it still doesn't match our utilization scenario closely.
1) user need write a user space parser to process the syslog output;
2) Our testing scenario is we leave the mobile for at least hours.
   Then, check its status. No serial console available during the
   testing. One is because console would be suspended, and the other
   is serial console connecting with spi or HSU devices would consume
   power. These devices are powered off at suspend-2-ram.

Signed-off-by: ShuoX Liu <shuox.liu@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2011-10-16 23:27:45 +02:00
Kevin Hilman a5e4fd8783 PM / Suspend: Export suspend_set_ops, suspend_valid_only_mem
Some platforms wish to implement their PM core suspend code as
modules.  To do so, these functions need to be exported to modules.

[rjw: Replaced EXPORT_SYMBOL with EXPORT_SYMBOL_GPL]

Reported-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2011-07-15 23:58:19 +02:00
MyungJoo Ham 3b5fe85252 PM / Suspend: Add .suspend_again() callback to suspend_ops
A system or a device may need to control suspend/wakeup events. It may
want to wakeup the system after a predefined amount of time or at a
predefined event decided while entering suspend for polling or delayed
work. Then, it may want to enter suspend again if its predefined wakeup
condition is the only wakeup reason and there is no outstanding events;
thus, it does not wakeup the userspace unnecessary or unnecessary
devices and keeps suspended as long as possible (saving the power).

Enabling a system to wakeup after a specified time can be easily
achieved by using RTC. However, to enter suspend again immediately
without invoking userland and unrelated devices, we need additional
features in the suspend framework.

Such need comes from:

 1. Monitoring a critical device status without interrupts that can
wakeup the system. (in-suspend polling)
 An example is ambient temperature monitoring that needs to shut down
the system or a specific device function if it is too hot or cold. The
temperature of a specific device may be needed to be monitored as well;
e.g., a charger monitors battery temperature in order to stop charging
if overheated.

 2. Execute critical "delayed work" at suspend.
 A driver or a system/board may have a delayed work (or any similar
things) that it wants to execute at the requested time.
 For example, some chargers want to check the battery voltage some
time (e.g., 30 seconds) after the battery is fully charged and the
charger has stopped. Then, the charger restarts charging if the voltage
has dropped more than a threshold, which is smaller than "restart-charger"
voltage, which is a threshold to restart charging regardless of the
time passed.

This patch allows to add "suspend_again" callback at struct
platform_suspend_ops and let the "suspend_again" callback return true if
the system is required to enter suspend again after the current instance
of wakeup. Device-wise suspend_again implemented at dev_pm_ops or
syscore is not done because: a) suspend_again feature is usually under
platform-wise decision and controls the behavior of the whole platform
and b) There are very limited devices related to the usage cases of
suspend_again; chargers and temperature sensors are mentioned so far.

With suspend_again callback registered at struct platform_suspend_ops
suspend_ops in kernel/power/suspend.c with suspend_set_ops by the
platform, the suspend framework tries to enter suspend again by
looping suspend_enter() if suspend_again has returned true and there has
been no errors in the suspending sequence or pending wakeups (by
pm_wakeup_pending).

Tested at Exynos4-NURI.

[rjw: Fixed up kerneldoc comment for suspend_enter().]

Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2011-07-15 23:58:19 +02:00
Rafael J. Wysocki 2d2a9163bd Merge branch 'syscore' into for-linus
* syscore:
  PM: Remove sysdev suspend, resume and shutdown operations
  PM / PowerPC: Use struct syscore_ops instead of sysdevs for PM
  PM / UNICORE32: Use struct syscore_ops instead of sysdevs for PM
  PM / AVR32: Use struct syscore_ops instead of sysdevs for PM
  PM / Blackfin: Use struct syscore_ops instead of sysdevs for PM
  ARM / Samsung: Use struct syscore_ops for "core" power management
  ARM / PXA: Use struct syscore_ops for "core" power management
  ARM / SA1100: Use struct syscore_ops for "core" power management
  ARM / Integrator: Use struct syscore_ops for core PM
  ARM / OMAP: Use struct syscore_ops for "core" power management
  ARM: Use struct syscore_ops instead of sysdevs for PM in common code
2011-05-17 23:23:40 +02:00
MyungJoo Ham 3c43193608 PM / Suspend: Do not ignore error codes returned by suspend_enter()
The current implementation of suspend-to-RAM returns 0 if there is an
error from suspend_enter(), because suspend_devices_and_enter() ignores
the return value from suspend_enter().  This patch addresses this issue
and properly keep the error return from suspend_enter() and let
suspend_devices_and_enter relay the error return.

Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2011-05-17 23:19:16 +02:00
Rafael J. Wysocki 2e711c04db PM: Remove sysdev suspend, resume and shutdown operations
Since suspend, resume and shutdown operations in struct sysdev_class
and struct sysdev_driver are not used any more, remove them.  Also
drop sysdev_suspend(), sysdev_resume() and sysdev_shutdown() used
for executing those operations and modify all of their users
accordingly.  This reduces kernel code size quite a bit and reduces
its complexity.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-11 21:37:15 +02:00
Rafael J. Wysocki 87186475a4 PM: Fix warning in pm_restrict_gfp_mask() during SNAPSHOT_S2RAM ioctl
A warning is printed by pm_restrict_gfp_mask() while the
SNAPSHOT_S2RAM ioctl is being executed after creating a hibernation
image, because pm_restrict_gfp_mask() has been called once already
before the image creation and suspend_devices_and_enter() calls it
once again.  This happens after commit 452aa6999e
(mm/pm: force GFP_NOIO during suspend/hibernation and resume).

To avoid this issue, move pm_restrict_gfp_mask() and
pm_restore_gfp_mask() from suspend_devices_and_enter() to its caller
in kernel/power/suspend.c.

Reported-by: Alexandre Felipe Muller de Souza <alexandrefm@mandriva.com.br>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
2011-05-11 21:10:14 +02:00
Rafael J. Wysocki 2ca6f62f59 PM: Fix error code paths executed after failing syscore_suspend()
If syscore_suspend() fails in suspend_enter(), create_image() or
resume_target_kernel(), it is necessary to call sysdev_resume(),
because sysdev_suspend() has been called already and succeeded
and we are going to abort the transition.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-18 23:58:59 +02:00
Rafael J. Wysocki 40dc166cb5 PM / Core: Introduce struct syscore_ops for core subsystems PM
Some subsystems need to carry out suspend/resume and shutdown
operations with one CPU on-line and interrupts disabled.  The only
way to register such operations is to define a sysdev class and
a sysdev specifically for this purpose which is cumbersome and
inefficient.  Moreover, the arguments taken by sysdev suspend,
resume and shutdown callbacks are practically never necessary.

For this reason, introduce a simpler interface allowing subsystems
to register operations to be executed very late during system suspend
and shutdown and very early during resume in the form of
strcut syscore_ops objects.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-03-15 00:43:46 +01:00
Linus Torvalds 008d23e485 Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
  Documentation/trace/events.txt: Remove obsolete sched_signal_send.
  writeback: fix global_dirty_limits comment runtime -> real-time
  ppc: fix comment typo singal -> signal
  drivers: fix comment typo diable -> disable.
  m68k: fix comment typo diable -> disable.
  wireless: comment typo fix diable -> disable.
  media: comment typo fix diable -> disable.
  remove doc for obsolete dynamic-printk kernel-parameter
  remove extraneous 'is' from Documentation/iostats.txt
  Fix spelling milisec -> ms in snd_ps3 module parameter description
  Fix spelling mistakes in comments
  Revert conflicting V4L changes
  i7core_edac: fix typos in comments
  mm/rmap.c: fix comment
  sound, ca0106: Fix assignment to 'channel'.
  hrtimer: fix a typo in comment
  init/Kconfig: fix typo
  anon_inodes: fix wrong function name in comment
  fix comment typos concerning "consistent"
  poll: fix a typo in comment
  ...

Fix up trivial conflicts in:
 - drivers/net/wireless/iwlwifi/iwl-core.c (moved to iwl-legacy.c)
 - fs/ext4/ext4.h

Also fix missed 'diabled' typo in drivers/net/bnx2x/bnx2x.h while at it.
2011-01-13 10:05:56 -08:00
Linus Torvalds c8940eca75 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  spi / PM: Support dev_pm_ops
  PM: Prototype the pm_generic_ operations
  PM / Runtime: Generic resume shouldn't set RPM_ACTIVE unconditionally
  PM: Use dev_name() in core device suspend and resume routines
  PM: Permit registration of parentless devices during system suspend
  PM: Replace the device power.status field with a bit field
  PM: Remove redundant checks from core device resume routines
  PM: Use a different list of devices for each stage of device suspend
  PM: Avoid compiler warning in pm_noirq_op()
  PM: Use pm_wakeup_pending() in __device_suspend()
  PM / Wakeup: Replace pm_check_wakeup_events() with pm_wakeup_pending()
  PM: Prevent dpm_prepare() from returning errors unnecessarily
  PM: Fix references to basic-pm-debugging.txt in drivers-testing.txt
  PM / Runtime: Add synchronous runtime interface for interrupt handlers (v3)
  PM / Hibernate: When failed, in_suspend should be reset
  PM / Hibernate: hibernation_ops->leave should be checked too
  Freezer: Fix a race during freezing of TASK_STOPPED tasks
  PM: Use proper ccflag flag in kernel/power/Makefile
  PM / Runtime: Fix comments to match runtime callback code
2011-01-10 08:14:53 -08:00
Jean Pihet 938cfed18b perf: Add calls to suspend trace point
Uses the machine_suspend trace point, called from the
generic kernel suspend_devices_and_enter function.

Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Arjan van de Ven <arjan@linux.intel.com>
CC: Thomas Renninger <trenn@suse.de>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linux-pm@lists.linux-foundation.org
LKML-Reference: <1294253342-29056-2-git-send-email-j-pihet@ti.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2011-01-05 21:25:28 +01:00
Rafael J. Wysocki a2867e08c8 PM / Wakeup: Replace pm_check_wakeup_events() with pm_wakeup_pending()
To avoid confusion with the meaning and return value of
pm_check_wakeup_events() replace it with pm_wakeup_pending() that
will work the other way around (ie. return true when system-wide
power transition should be aborted).

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2010-12-24 15:02:42 +01:00
Jiri Kosina 4b7bd36470 Merge branch 'master' into for-next
Conflicts:
	MAINTAINERS
	arch/arm/mach-omap2/pm24xx.c
	drivers/scsi/bfa/bfa_fcpim.c

Needed to update to apply fixes for which the old branch was too
outdated.
2010-12-22 18:57:02 +01:00
Rafael J. Wysocki c9e664f1fd PM / Hibernate: Fix memory corruption related to swap
There is a problem that swap pages allocated before the creation of
a hibernation image can be released and used for storing the contents
of different memory pages while the image is being saved.  Since the
kernel stored in the image doesn't know of that, it causes memory
corruption to occur after resume from hibernation, especially on
systems with relatively small RAM that need to swap often.

This issue can be addressed by keeping the GFP_IOFS bits clear
in gfp_allowed_mask during the entire hibernation, including the
saving of the image, until the system is finally turned off or
the hibernation is aborted.  Unfortunately, for this purpose
it's necessary to rework the way in which the hibernate and
suspend code manipulates gfp_allowed_mask.

This change is based on an earlier patch from Hugh Dickins.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Hugh Dickins <hughd@google.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: stable@kernel.org
2010-12-06 23:52:08 +01:00
Lionel Debroux 2f55ac072f suspend: constify platform_suspend_ops
While at it, fix two checkpatch errors.
Several non-const struct instances constified by this patch were added after
the introduction of platform_suspend_ops in checkpatch.pl's list of "should
be const" structs (79404849e9).

Patch against mainline.
Inspired by hunks of the grsecurity patch, updated for newer kernels.

Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-11-16 14:14:02 +01:00
Rafael J. Wysocki ce4410116c PM / Suspend: Fix ordering of calls in suspend error paths
The ACPI suspend code calls suspend_nvs_free() at a wrong place,
which may lead to a memory leak if there's an error executing
acpi_pm_prepare(), because acpi_pm_finish() will not be called in
that case.  However, the root cause of this problem is the
apparently confusing ordering of calls in suspend error paths that
needs to be fixed.

In addition to that, fix a typo in a label name in suspend.c.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Len Brown <len.brown@intel.com>
2010-07-19 02:00:35 +02:00
Rafael J. Wysocki c125e96f04 PM: Make it possible to avoid races between wakeup and system sleep
One of the arguments during the suspend blockers discussion was that
the mainline kernel didn't contain any mechanisms making it possible
to avoid races between wakeup and system suspend.

Generally, there are two problems in that area.  First, if a wakeup
event occurs exactly when /sys/power/state is being written to, it
may be delivered to user space right before the freezer kicks in, so
the user space consumer of the event may not be able to process it
before the system is suspended.  Second, if a wakeup event occurs
after user space has been frozen, it is not generally guaranteed that
the ongoing transition of the system into a sleep state will be
aborted.

To address these issues introduce a new global sysfs attribute,
/sys/power/wakeup_count, associated with a running counter of wakeup
events and three helper functions, pm_stay_awake(), pm_relax(), and
pm_wakeup_event(), that may be used by kernel subsystems to control
the behavior of this attribute and to request the PM core to abort
system transitions into a sleep state already in progress.

The /sys/power/wakeup_count file may be read from or written to by
user space.  Reads will always succeed (unless interrupted by a
signal) and return the current value of the wakeup events counter.
Writes, however, will only succeed if the written number is equal to
the current value of the wakeup events counter.  If a write is
successful, it will cause the kernel to save the current value of the
wakeup events counter and to abort the subsequent system transition
into a sleep state if any wakeup events are reported after the write
has returned.

[The assumption is that before writing to /sys/power/state user space
will first read from /sys/power/wakeup_count.  Next, user space
consumers of wakeup events will have a chance to acknowledge or
veto the upcoming system transition to a sleep state.  Finally, if
the transition is allowed to proceed, /sys/power/wakeup_count will
be written to and if that succeeds, /sys/power/state will be written
to as well.  Still, if any wakeup events are reported to the PM core
by kernel subsystems after that point, the transition will be
aborted.]

Additionally, put a wakeup events counter into struct dev_pm_info and
make these per-device wakeup event counters available via sysfs,
so that it's possible to check the activity of various wakeup event
sources within the kernel.

To illustrate how subsystems can use pm_wakeup_event(), make the
low-level PCI runtime PM wakeup-handling code use it.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: markgross <markgross@thegnar.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
2010-07-19 01:58:48 +02:00
Matthew Garrett dd4c4f17d7 suspend: Move NVS save/restore code to generic suspend functionality
Saving platform non-volatile state may be required for suspend to RAM as
well as hibernation. Move it to more generic code.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2010-06-10 11:02:34 -04:00
Tejun Heo 5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Rafael J. Wysocki 452aa6999e mm/pm: force GFP_NOIO during suspend/hibernation and resume
There are quite a few GFP_KERNEL memory allocations made during
suspend/hibernation and resume that may cause the system to hang, because
the I/O operations they depend on cannot be completed due to the
underlying devices being suspended.

Avoid this problem by clearing the __GFP_IO and __GFP_FS bits in
gfp_allowed_mask before suspend/hibernation and restoring the original
values of these bits in gfp_allowed_mask durig the subsequent resume.

[akpm@linux-foundation.org: fix CONFIG_PM=n linkage]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:26 -08:00
Rafael J. Wysocki a9d7052363 PM: Separate suspend to RAM functionality from core
Move the suspend to RAM and standby code from kernel/power/main.c
to two separate files, kernel/power/suspend.c containing the basic
functions and kernel/power/suspend_test.c containing the automatic
suspend test facility based on the RTC clock alarm.

There are no changes in functionality related to these modifications.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
2009-06-12 21:32:33 +02:00