wm5110 rev D is the first chip to use headphone detection IP 2, specify
such and make a small correction as the impedance value is actually read
in 0.5 ohm increments now.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
No point in revisiting ranges the detection will be no more accurate
the second time simply report that the resistance is right on the
range boundry.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The microphone detection code is run as delayed work to provide
additional debounce, it is possible that the jack could have been
removed by the time we process the microphone detection. Turn this
case into a no op.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
We need to make sure we reset back to our starting state, especially
making sure that we have disabled poll in the register cache.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Improve readability by creating a define for each microphone detection
level.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
In the case of a device tree system there will be no pdata attached to
the device, causing us to deference a NULL pointer. Better to take the
pdata from the Arizona structure as this will always exist and we know
will have been populated since it is populated by the MFD device which
binds in the extcon driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patchset modify extcon core to remove unnecessary allocation sequence for
'dev' instance and change extcon_dev_register() interface. extcon-gpio use
gpiolib API to get debounce time and include small fix of extcon core/device
driver.
Detailed description for patchset:
1. Modify extcon core driver
- The extcon-gpio driver use gpio_set_debounce() API provided from gpiolib
if gpio driver for SoC support gpio_set_debounce() function and support 'gpio_
activ_low' filed to check whether gpio active state is 1(high) or 0(low).
- Change field type of 'dev' in structure extcon_dev and remove the sequence
of allocating memory of 'struct dev' on extcon_dev_register() function because
extcon device must need 'struct device.
- Change extcon_dev_register() prototype to simplify it and remove unnecessary
parameter as below:
2. Fix coding style and typo
- extcon core : Fix indentation coding style and remove unnecessary casting
- extcon-max8997 : Fix checkpatch warning
- extcon-max77693 : Fix checkpatch warning
- extcon-arizona : Fix typo of comment and modify minor issue
- extcon-palmas : Use dev_get_platdata()
3. Modify extcon-arizona driver
- Modify minor issue about micbias and comparision statement
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8Hr2
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next
Chanwoo writes:
Update extcon for 3.13
This patchset modify extcon core to remove unnecessary allocation sequence for
'dev' instance and change extcon_dev_register() interface. extcon-gpio use
gpiolib API to get debounce time and include small fix of extcon core/device
driver.
Detailed description for patchset:
1. Modify extcon core driver
- The extcon-gpio driver use gpio_set_debounce() API provided from gpiolib
if gpio driver for SoC support gpio_set_debounce() function and support 'gpio_
activ_low' filed to check whether gpio active state is 1(high) or 0(low).
- Change field type of 'dev' in structure extcon_dev and remove the sequence
of allocating memory of 'struct dev' on extcon_dev_register() function because
extcon device must need 'struct device.
- Change extcon_dev_register() prototype to simplify it and remove unnecessary
parameter as below:
2. Fix coding style and typo
- extcon core : Fix indentation coding style and remove unnecessary casting
- extcon-max8997 : Fix checkpatch warning
- extcon-max77693 : Fix checkpatch warning
- extcon-arizona : Fix typo of comment and modify minor issue
- extcon-palmas : Use dev_get_platdata()
3. Modify extcon-arizona driver
- Modify minor issue about micbias and comparision statement
This patch remove extcon_dev_register()'s second parameter which means
the pointer of parent device to simplify prototype of this function.
So, if extcon device has the parent device, it should set the pointer of
parent device to edev.dev.parent in extcon device driver instead of in
extcon_dev_register().
Cc: Graeme Gregory <gg@slimlogic.co.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Every other pdata field is specified unshifted the patch handles
shifting for the MICBIAS from the microphone detection polarity
configurations in the extcon driver rather than demanding it in
pdata to match other fields.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
We should move range when the measured value is greater than or equal to
the max value not when greater than.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
We want the trig_sts bits to be cleared in all cases where we consider
the jack detection interrupt to have been handled. Specifically, if a
duplicate detection event was suppressed these bits were not cleared
causing the CODEC to not enter a low power state. This patch clears the
bits on the duplicate detection code path.
Reported-by: Ryo Tsutsui <ryo.tsutsui@wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This fixes up braces coding style issue by using checkpatch script.
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix 80 column coding sytle issues by using checkpatch script.
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
None of the delayed work the driver schedules has particularly short delays
and it is not performance sensitive so let the scheduler run it wherever
is most efficient rather than in a per CPU workqueue by using the system
power efficient workqueue.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Help mitigate against mechanical bounce during the initial detection by
allowing the configuration of an additional debounce on top of that the
hardware does during the initial phase of microphone detection operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the user moves directly from one button to another then we won't get a
no buttons pressed event and will therefore end up reporting that two
buttons are simultaneously pressed which isn't supported by the hardware.
Make sure we clear any existing button reports before reporting any new
ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In pathological cases the microphone detection may fail to report, for
example due to a failure to get a stable measurement. Provide a timeout
to cover such cases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than measuring both HP channels we can simply directly measure the
microphone impedance and then rely on MICDET for final confirmation of the
presence of a suitable microphone. This improves the overall performance
of the identification process.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This extra check makes the procedure take longer and is of marginal use
in identification so do not execute it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sometimes we can trigger measurements early if contacts are shorted during
a slow insertion. As well as debouncing add further robustness by retrying
if we get a high impedance measurement for headphones as this can indicate
that the headphones were not yet connected.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Occasionally we can trigger an interrupt before we have completed
impedance measurement, although the valid bit will still be set. This
patch spins reading the impedance value until a valid value is seen.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In cases where we see a brief (dis)connection of the jack detection signals
we may see a noop jack insertion or removal where the jack has returned to
the original state by the time the interrupt is serviced. Suppress these
events in order to save work and avoid confusing the rest of the code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure greater reliability by increasing the minimum threashold for
identifying a microphone.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to do this as HPDET identification will cause MICBIAS to
be powered down again.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Arizona button detection circuit is configurable, allowing the system
integrator to program a range of thresholds for the buttons supported on
the accessory but currently the driver uses the default button ranges and
does not provide any flexibility in how this is exposed to the application
layer.
Provide platform data allowing the user to control this and to map
the buttons to keys in the input subsystem.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In some pathological use cases users may insert an accessory very slowly
causing multiple indeterminate measurements. Handle this by retrying many
measurements before we give up and declare a headphone.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Running HPDET while the headphone outputs are enabled can disrupt the
operation of HPDET. In order to avoid this HPDET needs to disable the
headphone outputs and ASoC needs to not enable them while HPDET is
running.
For extcon instead of checking if the headphone output is enabled when
doing magic application unconditionally disable the output and restore
the state which ASoC wants set when undoing the magic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have a very similar sequence doing magic writes in several places
(one of which missed an update to interlock with the CODEC driver) so
factor it out into a function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When using HPDET to identify the accessory still run MICDET before we
report a microphone in order to ensure that the accessory identified is
compatible with the MICDET detection ranges after having confirmed that
the device is not using a headphone.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This should always be the most accurate reading for supported accessory
configurations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is important to clear the wake trigger status bits otherwise DCVDD
will be held high independent of the state of the LDOENA line.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The magic is already done as part of enabling the headphone output so
does not need to be done when the headphone outputs are enabled. We hold
the DAPM lock so the headphone status can't be changed underneath us.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The HPDET identification method does not have the same natural debounce
built into it that the standard MICDET method does so add some extra on
top of what the jack detection does in hardware to make sure we get a
robust result.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When starting microphone detection some headsets should be exposed to
the fully regulated microphone bias in order to ensure that they behave
in an optimal fashion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow systems to tune detection rate and debounce suitably for their
mechanical parameters.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We now have mechanisms in place to allow retries so let's use them rather
than guessing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure we clamp as quickly as possible after removal by disabling the
debounce while there is an accessory present.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With some GPIO control it is possible to detect microphones in a wider
range of configurations by directly measuring the microphone impedance
when the HPDET method cannot distinguish between the behaviour of the
two grounds. Allow a GPIO to be provided in platform data and use it to
implement this behaviour.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
The accessory detection functionality in Arizona devices is flexible and
supports several system designs in addition to the default one implemented
by the existing driver. One such design uses the HPDET feature to determine
what kind of accessory is present by comparing measurements taken with the
two headphone grounds available on the device, implement that if selected
by platform data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Use the headphone detection to identify if the accessory is a headphone or
line load. There are two different revisions of the IP with different
register layouts, support both.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Some system designs provide an input on GPIO5 which in conjunction with
the jack detection feature indicates the presence of an accessory.
Support such systems, using the microphone clamp feature to minimise
wakeups of the processor.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Newer Arizona devices include a microphone clamp function which is tied to
jack detect. Activate this feature when present in order to ensure best
performance of the subsystem.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Allow configuration of the rise time for MICBIAS via platform data, the
delay required depends on things like the external component selection.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Charles Keepax
Greg Kroah-Hartman
Chanwoo Choi
Sachin Kamat
Mark Brown
Mark Brown